look up the accepted values for the linear expansion coefficient for aluminum, brass, and copper.compare these values with your experimental values. what is the percentage difference in each case? is your experimental error consistently high or low?

Because of the imbalance, the power protection circuits will activate

if the neutral wire is unplugged.

If the neutral wire is damaged or disconnected, the out-of-balance current cannot, but must, return to the supply via the star point. As a result, this current follows the wires back to the source. The neutral current and neutral power in a balanced system are both zero. A balanced three-phase system may be thought of as three single-phase systems linked to a neutral line. As a result, if the supply voltage and motor impedance are both balanced, the induction motor draws a balanced current. The balancing current in the motor's three phases results in no current in the neutral. As a result, there is no need for a neutral in a three-phase induction motor.

Learn more about  induction motor from here;

https://brainly.com/question/30337216

#SPJ4

A marble rolls off a tabletop that is 1.4 m high and lands horizontally at a place 2 m from the edge of the table, t = 0.45 sec, VT=4.95 m/s, V=2.22 m/s

The conservation of energy principle can be used to compute the speed of the marble roll when it lands on the ground. Due to its height, the stone only contains potential energy at its initial position. The stone only contains kinetic energy in its final position as a result of its motion.

Generally, the equation for motion is mathematically given as

S= ut + 0.5at²

Therefore

y = Vo t + 0.5gt^2

1 = 0.5x 98 x 6²

1=4.9t^2

t= 0.45 seconds.

c) The acceleration in the x-direction will be zero because there is no force operating in that direction.

d) Throughout the marble's flight, gravity is exerting itself on it in the y direction. As a result, the marble's acceleration in the y direction will be equal to the acceleration caused by gravity

b) Horizontal motions are uniform.

V=Horizontal displacement/time

V=1/0.45

V=2.22m/s

C) Vx: 2.22 m/s At bottom,

Vy² = Voy² + 2as

Vy² = 2x95x1

Vy² = 19.6

VT=4.95 m/s

Learn more about marble rolls here

https://brainly.com/question/27864202

#SPJ4

The hare is currently 100 meters from the finish line and 895 metres from the starting line. The tortoise is 895 m from the starting line and is travelling at a speed of 0.27 m/s in the direction of the finish line.

The tortoise must go 895 meters whereas the hare must travel only 100 meters to reach the finish line. The tortoise will keep moving towards the finish line and may finally cross it before the hare wakes up if the hare dozes off for a predetermined period of time.

Inertia has an impact on both moving and stationary objects, according to Newton's first law of motion. According to Newton's first law, an item will remain at rest or move straight ahead at a constant speed unless another force is operating on it that is not balanced.

Therefore, If the hare travels at a speed of 15 m/s, he can afford to rest for a maximum of 6.67 seconds without losing the race.

Learn more about speed here:

https://brainly.com/question/6280317

#SPJ4

Answer:

C. 7.3 kg

Explanation:

The weight of the shelf can be calculated using the equation:

W = mg

where m is the mass of the shelf and g is the acceleration due to gravity (10 m/s^2).

Since the tension in each wire is equal and equal to 80 N, the total tension in the two wires is 80 N + 80 N = 160 N.

The horizontal component of the tension in each wire can be calculated using the equation:

T_horizontal = T * cos(25)

where T is the tension in each wire and 25 is the angle between the wire and the horizontal.

The horizontal component of the tension in each wire is equal to the weight of the shelf, so we can set the two equal:

T_horizontal = W

80 * cos(25) = W

W = 80 * cos(25) = 74.17 N

Finally, we can calculate the mass of the shelf using the equation for weight:

m = W / g

m = 74.17 / 10

m = 7.417 kg

Therefore, the mass of the shelf is approximately 7.417 kg, which is closest to option C, 7.3 kg.

The engine does 1,358,400 Joules of work. The engine has a power of 340 kW. The car has 1,412,800 Joules of kinetic energy after 4 seconds.

A) The work done by the engine can be calculated using the work-energy theorem, which states that the work done on an object is equal to its change in kinetic energy. Therefore, the work done by the engine can be calculated as follows:

[tex]Work = (1/2) \times m \times v^2 - (1/2) \times m \times u^2[/tex]

where m is the mass of the car, v is the final velocity, and u is the initial velocity. Substituting the given values, we get:

[tex]Work = (1/2) \times 450 \times (88)^2 - (1/2) \times 450 \times (0)^2 = 1,358,400 J[/tex]

Therefore, the engine does 1,358,400 Joules of work.

B) The power of the engine is the rate at which it can do work. It can be calculated using the formula:

Power = Work / time

Substituting the values, we get:

Power = 1,358,400 J / 4 s = 339,600 watts or 340 kW (rounded to two significant figures)

Therefore, the engine has a power of 340 kW.

C) The kinetic energy of the car after 4 seconds can be calculated using the formula:

Kinetic energy = [tex](1/2) \times m \times v^2[/tex]

Substituting the given values, we get:

Kinetic energy =[tex](1/2) \times 450 \times (88)^2[/tex] [tex](1/2) \times 450 \times (88)^2[/tex]  = 1,412,800 J

Therefore, the car has 1,412,800 Joules of kinetic energy after 4 seconds.

To learn more about work, power, and kinetic energy:

brainly.com/question/14371286

#SPJ1

The density of the liquid in which the aluminum ball was submerged is found to be 2.7g/cm³.

When submerged in a certain liquid, a 3.90 kilogram aluminum metal ball has an apparent mass of 2.50 kg.

Aluminum has a density of 2.7gm/cm3.

We already know that 3.9 kg = 3900gm density = mass/volume

2.7 = 3900/volume

volume = 3900/2.7 cm³

We also know that the volume of liquid displaced Equals the volume of the ball,

The mass of liquid exhibited = the apparent weight of the Al ball = 2.5 kg = 2500 gm, and

Density of liquid = 2500/(3900/2.7)

= 2.7 gm/cm³

As a result, the density of the liquid is 2.7 gm/cm3.

To know more about density, visit,

https://brainly.com/question/1354972

#SPJ4

Plants get the energy to make their food through the flowers and is therefore denoted as option B.

This is referred to as the process in which green plants manufacture their food in the presence of sunlight and is the reason why they are referred to as primary producers.

Plants have flowers and leaves which help to trap sunlight from the sun through the chlorophyll. The chlorophyll is a green pigment which is present in the chloroplast and they are all found in the flowers of plants which is therefore the reason why it was chosen as the correct choice.

Read more about Photosynthesis here https://brainly.com/question/19160081

#SPJ1

A negative slope's graph slopes downhill from left to right. When viewing a graph on a xy coordinate plane, the slope is negative because as x rises, y falls.

The line is sloped downhill from left to right when there is a negative slope. Here, the inverse link between the two variables depicted along the x- and y-axes of the negative slope graph applies. The other variable decreases when the first variable goes up.

Negative values are below the origin on the y-axis and to the left of the origin on the x-axis. If the x-value is negative, begin at the origin and go to the left. In the event that the y-coordinate is negative, descend.

A line that slopes positively ascends from left to right. Remember that a line with a negative slope descends from left to right.

Therefore, Graph below the x axis and in the negative downward slope direction.

Learn more about Graph here:

https://brainly.com/question/1463001

#SPJ4

If an object is dropped, it is released from rest and falls freely under the influence of gravity. The acceleration due to gravity is approximately 10 m/s^2 near the surface of the Earth. This means that the object's speed will increase by 10 m/s every second it falls.

If the same object is thrown down instead of dropped, it will initially have some initial velocity in addition to the acceleration due to gravity. The acceleration due to gravity will remain the same at approximately 10 m/s^2. However, the total acceleration of the object will be the vector sum of the acceleration due to gravity and the initial acceleration from the throw.

If the object is thrown straight down, the initial velocity will be in the same direction as the acceleration due to gravity, and the total acceleration will be the sum of the magnitudes of the two accelerations, which is 10 m/s^2 + the initial acceleration from the throw.

To learn more about acceleration, visit here

https://brainly.com/question/12550364

#SPJ4

The diameter of the wire is 0.3 cm.

Wire gauge is a measurement of wire diameter. This determines the amount of electric current the wire can safely carry, as well as its electrical resistance and weight.

The diameter of the wire given in the question is calculated as follows;

Diameter of Wire = Length of wire/Number of turns of wire

from the diagram, the length of the wire = 3 cm

the number of turns of the wire = 10

Diameter of Wire = ( 3 cm ) / 10

Diameter of Wire = 0.3 cm

Learn more about diameter of wire here: https://brainly.com/question/24082232

#SPJ1

The two factors that can help determine air pressure are the temperature of the air and the cloud patterns in the air that are in options c and d, because wind speed and moisture content of the air are not direct measures of air pressure.

It depends upon the temperature, as when the temperature increases, air molecules gain energy and move faster, leading to a decrease in air pressure, and as the temperature decreases, there is an increase in air pressure. Some clouds are present at low air pressure, while others are at high air pressure.

Hence, the two factors that can help determine air pressure are the temperature of the air and the cloud patterns in the air that are in options c and d, because wind speed and moisture content of the air are not direct measures of air pressure.

Learn more about the air pressure here.

https://brainly.com/question/15189000

#SPJ1

The time for a pulse of laser light to reach the Moon and bounce back to Earth is 2.57 seconds.

It takes about 2 1/2 seconds for the laser light to go from Earth, be reflected off the surface of the moon, and come back. Distance from Earth to the moon in miles is about 238,900 miles.

477,000 miles or 2 x 238,900 is the round trip from Earth to Moon.

Light travels at 186,000 miles per second.

The total time taken is 477,000 miles / 186,000 miles/sec = 2.57 seconds.

We calculated the precise distance based on the time, divided by two, and the speed of light.

Thus, the time taken by the pulse of laser light to reach the Moon and bounce back to Earth is 2.57 seconds.

To learn more about the speed of light,

brainly.com/question/17771723

#SPJ4

The minimum uncertainty in the position of a proton accelerated in a cyclotron to a very high speed is equal to the wavelength of the light emitted from the particle as it is accelerated.

The minimum uncertainty in the position of the proton is determined by Heisenberg's uncertainty principle. According to this principle, the minimum uncertainty in the position of the proton is equal to the wavelength of the light used to measure its position. In other words, the minimum uncertainty in the position of the proton is equal to the inverse of the energy of the light used to measure its position. In the case of a cyclotron, the light used to measure the position of the proton is the light emitted from the particle as it is accelerated. The energy of this light is related to the speed of the proton. Thus, the minimum uncertainty in the position of the proton is equal to the inverse of the energy of the light, which is equal to the inverse of the speed of the proton - or the wavelength of the light emitted from the particle as it is accelerated.

To learn more about uncertainty click here https://brainly.com/question/15103386

#SPJ4

Answer:

The formula for calculating the length change due to a temperature change is:

ΔL = α * L * ΔT

where α is the linear expansivity, L is the original length of the bar, and ΔT is the change in temperature.

So in this case, the length change of each bar would be:

ΔL = 1.0 x 10^-5 K^-1 * 3m * (40°C - 28°C)

Converting the temperatures to Kelvin (28°C = 28 + 273 = 301 K and 40°C = 40 + 273 = 313 K), we get:

ΔL = 1.0 x 10^-5 K^-1 * 3m * (313 K - 301 K)

ΔL = 1.0 x 10^-5 * 3 * 12

ΔL = 0.00036 m

So each bar will increase in length by approximately 0.00036 meters when the temperature changes from 28°C to 40°C. To allow for this increase in length, a safety gap of 0.00036 meters should be left between each bar.

Answer:

Uniform Motion

Explanation:

When an object travels equal distances (in this case displacement) in equal intervals of time, it is said to be in uniform motion.

By estimating, we can see if the response is reasonable: 2.5 m/s is the product of 5 metres and 2 seconds.Therefore answer is 2.5m/s.

By dividing the amount of time it took the object to go a certain distance by the overall distance, one can calculate the object's initial velocity. V is the speed, d is the distance, and t is the time in the equation V = d/t.An object's terminal velocity is its top possible speed as it plunges through a liquid (air is the most common example). It happens when the object is subjected to a downward force of gravity (FG) equal to the total of the drag force (Fd) and buoyancy.

To know more about velocity visit:

https://brainly.com/question/30559316

#SPJ1

The distance on the screen from the unscattered slit image to the first-order violet line is 0.00514 cm.

What is Transmission?

In physics, transmission refers to the passage of waves, particles, or energy through a medium or barrier, without any change in the shape or form of the wave. This can occur in various contexts, such as the transmission of electromagnetic waves (such as light) through a material, the transmission of sound waves through the air, or the transmission of particles (such as electrons or ions) through a solid-state material.

The distance d between the central bright fringe and the first-order bright fringe for a transmission diffraction grating is given by:

dλ = mD

where λ is the wavelength of light, m is the order of the bright fringe, D is the distance between the grating and the screen, and d is the distance between adjacent slits on the grating.

For a hydrogen spectrum, the wavelengths of the first three visible (first-order) lines are:

λ_1 = 656.3 nm (red line)

λ_2 = 486.1 nm (blue-green line)

λ_3 = 434.0 nm (violet line)

The distance between adjacent slits on the grating is:

d = 1/325 mm = 0.00308 cm

The distance between the grating and the screen is D = 2.6 m = 260 cm.

For the first-order red line (m = 1, λ = 656.3 nm), we have:

dλ = mD

0.00308 cm * 656.3 nm = 1 * 260 cm * x

Solving for x, we get:

x = (0.00308 cm * 656.3 nm) / 260 cm = 0.00776 cm

So, the distance on the screen from the unscattered slit image to the first-order red line is 0.00776 cm.

For the first-order blue-green line (m = 1, λ = 486.1 nm), we have:

dλ = mD

0.00308 cm * 486.1 nm = 1 * 260 cm * x

Solving for x, we get:

x = (0.00308 cm * 486.1 nm) / 260 cm = 0.00579 cm

So, the distance on the screen from the unscattered slit image to the first-order blue-green line is 0.00579 cm.

For the first-order violet line (m = 1, λ = 434.0 nm), we have:

dλ = mD

0.00308 cm * 434.0 nm = 1 * 260 cm * x

Solving for x, we get:

x = (0.00308 cm * 434.0 nm) / 260 cm = 0.00514 cm

So, the distance on the screen from the unscattered slit image to the first-order violet line is 0.00514 cm.

Learn more about  Transmission from given link

https://brainly.com/question/14280351

#SPJ1

The friction coefficients are 0.25 for kinetic friction and 0.35 for static friction. 19.29° is the smallest angle at which the box begins to slide. Once the motion of the box has started.

the acceleration is 0.926 m/s2. The box will be traveling at 3.043 m/s once it has slid 5.0 meters along the loading ramp.

Given,m=25 kg

[tex]r_{K}[/tex]=0.25 and [tex]\mu_{s}[/tex]=0.35

here, N=mg cosθ

so, frictional force(f)=μN=μ×mg×cosθ

a). when the box starts to slip

mg sinθ ≤ f[tex]_{s}[/tex]

mg.sinθ = [tex]\mu_{s}[/tex].mg.sinθ

tanθ = [tex]\mu_{s}[/tex]

θ =tan⁻¹(0.35)=19.29°

b)here, F[tex]_{net}[/tex]=mg sinθ-f[tex]_{k}[/tex]=mg sinθ -[tex]\mu_{k}[/tex].mg.cosθ

a=[tex]\frac{F_{net} }{m}[/tex]

a=9.81 m/s²

a=0.926 m/s²

c)here d=5m

since, initial velocity=0m/s

so,[tex]v_{f}[/tex]=√2ad=√2(0.926)(5)=3.043 m/s

Friction is a force that opposes motion between two surfaces in contact. It arises due to the interlocking of microscopic protrusions on the surfaces, which makes it difficult for the surfaces to slide past each other. Friction is a complex phenomenon that depends on factors such as the nature of the surfaces in contact, the roughness of the surfaces, and the force pressing the surfaces together. Friction can be beneficial, as it allows us to walk, drive cars, and use brakes to stop moving objects. However, friction can also be detrimental, as it can cause wear and tear on machinery and reduce efficiency.

Learn more about Friction here:

https://brainly.com/question/29573486

#SPJ4

Using the wave equation, the velocity of the wave on the string can be calculated as 55.0 m/s. Using this, the tension needed to tune the string can be calculated as 1,101 N.

The frequency of a vibrating string is directly proportional to the tension in the string and inversely proportional to its length. This means that as tension increases, the frequency of the string also increases, while a decrease in length will result in a higher frequency as well. The relationship between tension, frequency, and length of a vibrating string is described by the wave equation, which states that the speed of the wave (and hence the frequency) is equal to the square root of the tension divided by the linear density of the string, multiplied by the reciprocal of the length.

To know more about Frequency visit:

https://brainly.com/question/5102661

#SPJ4

If a body puts a 400 N force on a rope, the rope likewise exerts a 400 N force on the body. As a result, the tension in the rope is 400N.

This is determined by whether both persons are tugging in the same direction against a fixed object or against each other. When both forces are applied in the same direction, the total force is 300 N + 300 N = 600 N. If two persons pull on the rope at the same time, the total force in the rope is 300 N, or a net of zero. Newton's third law of motion deals with these two forces, which are known as action and reaction forces. The rope is used to transfer forces in this activity. The action force is the first team to tug, generating the draw on the rope; as the response force, the opposing team's rope end "feels" the pull.

Learn more about Newton's third law from here;

https://brainly.com/question/29768600

#SPJ4

A piece of rope is pulled by two people in a tug-of-war. each pulls with 400 n of force, the tension in the rope is 400N.

Tension is a force along the length of a medium, especially a force carried by a flexible medium, such as a rope or cable. Tension can be defined as an action-reaction pair of forces acting at each end of the said elements.

If one of the forces exerting an object is a rope, cable or chain, you can call it tension. Cables and Ropes can be used for exerting forces since they can efficiently transfer a force over a specific distance (e.g. the rope length). Please note that tension is the pulling force since ropes cannot push effectively.

This is determined by whether both persons are tugging in the same direction against a fixed object or against each other. When both forces are applied in the same direction, the total force is 300 N + 300 N = 600 N.

The SI unit of Surface Tension is Newton per Meter or N/m.

Learn more about tension here:-

https://brainly.com/question/15880959

#SPJ4

(a) The pressure between the student and the floor is 817 Pa.

(b) The pressure between the student and each nail 14,848 Pa.

Pressure is calculated by dividing force by area. The force exerted on the floor by the student is equal to their weight, which is the force of gravity acting on their mass.

The weight of the student can be calculated as follows:

W = mg

W = 50 kg (9.8 m/s²)

W = 490 N

So the pressure between the student and the floor can be calculated as follows:

P = F / A

P = 490 N / 0.6 m²

P = 817 Pa

To find the pressure between the student and each nail, we need to divide the student's weight by the total area of the nails' heads.

A_nails = N_nails  x  A_head

A_nails = 3300 x 1 x 10⁻⁷ m²

A_nails = 0.033 m²

So the pressure between the student and each nail can be calculated as follows:

P = F / A

P = 490 N / 0.033 m²

P = 14,848 Pa

Learn more about pressure here: https://brainly.com/question/28012687

#SPJ1

The reading on scale F₂ when the cart moves right with the specified acceleration is calculated to be -7.27 N.

The acceleration is given as 5.5 m/s².

The reading on the scale F₂ is to be found out.

From the question we are told that,

The first force is, F₁ = 10.5 N.

The acceleration by which the cart moves to the right is, a = 5.5 m/s².

The mass of the cart is m = 3.231 kg

So, the net force on the cart is,

F net = F₁ - F₂

This force can be written as,

F net = m a

Hence,

m a = 10.5 - F₂

F₂ = 10.5 - m a = 10.5 - (3.231)(5.5) = 10.5 - 17.77 = -7.27 N

The given question is incomplete. The complete question is given in the attachment below.

To know more about scale reading:

https://brainly.com/question/17101190

#SPJ4

The required work done by the combined force is -2.572 × 10⁶ J and the negative sign indicates that the force has component in the direction to the displacement.

We know that the work done by all forces equals the change in potential energy

w friction + w air + w engine  = mv²f + mghf/2  - mv²i + mghi/2

Here,

hi = 0 m

vi = 0 m/s

When we combine all of the supplied values, we get:

W friction + W air + 4.30 * 10⁶ = m × (v²f+ ghf)/2 - 0

W friction + W air  = 1.5 × 10³ × (24² + 9.8 × 2.2 × 10²)/2 - 4.30 × 10⁶

W friction + W air  = -2.572 × 10⁶ j

Friction is a force that resists the motion of things; friction may cause items to slow down. Friction is represented by air resistance. Moving objects are slowed by air resistance. The air resistance of an item is affected by physical features such as its form.

When air pushes against a moving object, it creates air resistance force. Frictional forces include air resistance. Force is always applied against the motion of an item.

Learn more about Friction  from here;

https://brainly.com/question/13000653

#SPJ4

Correct Question:

The (nonconservative) force propelling a 1.50 × 10³ kg car up a mountain road does 4.30 × 10⁶ J of work on the car. the car starts from rest at sea level and has a speed of 24.0 m/s at an altitude of 2.10 × 10² m above sea level. obtain the work done on the car by the combined forces of friction and air resistance, both of which are nonconservative forces.

When a closed pipe vibrates in basic mode, there is one node and one antinode.

There are two nodes and two antinodes when it vibrates in the first overtone.

As it vibrates in second overtone, there are three nodes and three antinodes.

There are four nodes and four antinodes when it vibrates in the third overtone.

The reflection is not perfect at the open end: some energy escapes. Indeed, this is self-evident, because an organ pipe would not generate any sound if no energy could exit. The sound we hear is energy escaping from the open end. We can only have odd-numbered harmonics in closed tubes. Because closed tubes, by definition, contain a node at one end and an antinode at the other, even-numbered frequencies cannot exist. We can only have odd-numbered harmonics in closed tubes. Because closed tubes, by definition, contain a node at one end and an antinode at the other, even-numbered frequencies cannot exist.

Learn more about harmonics from here;

https://brainly.com/question/9253932

#SPJ4

Switching the position of the power leads from the Pasco power supply on your templates would reverse the direction of the electric field between the electrodes in the template.

This would result in a reversal of the direction of the current flow and a corresponding reversal of the direction of the magnetic field induced in the sample being measured.

            As a result, the contour plots would be mirrored or flipped along a vertical axis compared to the original plots obtained with the power leads in their original position. The areas of highest and lowest magnetic field strength would be swapped, and the field lines would curve in the opposite direction.

            Additionally, any current-induced magnetic effects in the sample being measured would be reversed. For example, if the sample contained a current-carrying wire or coil, the direction of the induced magnetic field would also be reversed, and the contour plots would show a different pattern of magnetic field lines.

         It is important to note that reversing the direction of the electric field in the template could potentially cause other effects or changes in the measurement, depending on the specific experiment or setup being used. Therefore, it is important to carefully consider the effects of any changes in the experimental setup and to account for these effects in the analysis of the results.

For more such questions on contour plots

https://brainly.com/question/15165662

#SPJ4

Answer:

A change in quantity demanded refers to a variation in the amount of a good or service that consumers are willing and able to purchase, given the same price. The change in quantity demanded can be either an increase or a decrease.

Explanation:

There are several factors that can cause a change in quantity demanded:

Price change: A change in the price of a good or service can cause a change in the quantity demanded. If the price of a good or service increases, the quantity demanded will decrease (assuming everything else remains constant), and if the price decreases, the quantity demanded will increase.

Income: A change in consumer income can cause a change in the quantity demanded. If income increases, consumers may be able to afford to buy more of a good or service, which will cause the quantity demanded to increase. If income decreases, consumers may not be able to afford as much, which will cause the quantity demanded to decrease.

Tastes and preferences: Changes in tastes and preferences can also cause a change in quantity demanded. For example, if a new trend or fashion becomes popular, consumers may start to demand more of the goods or services associated with that trend.

Expectations: Consumers' expectations about future prices, availability, and income can also cause changes in the quantity demanded. For example, if consumers expect the price of a good or service to increase in the future, they may buy more of it now, which will cause the quantity demanded to increase.

Number of buyers: The number of buyers in the market can also affect the quantity demanded. An increase in the number of buyers will increase the quantity demanded, while a decrease will decrease the quantity demanded.

The centripetal force causes angular or circular motion by pulling or pushing an item in the direction of the centre of a circle as it moves.

Rotating is the process of an object moving in a circular path. The centripetal force exerts a push perpendicular to the velocity of the item in the direction of the curve's centre. The object's velocity changes direction due to the centripetal force, even while its speed is unaltered.

Work can only be done by the force component that is acting in the direction of motion. Without such a component, the centripetal force is incapable of doing work.

[tex]F_c =F_f[/tex]

[tex]mv2/r = \mu mg[/tex]

Vmax = √(μgr)

Vmax =√(0.08×9.81×0.15)

Vmax [tex]=0.343m/s[/tex]

Therefore, 0.343 m/s Maximum speed occurs when centripetal force equal to frictional force.

Learn more about centripetal force here:

https://brainly.com/question/11324711

#SPJ4

The above question is incomplete. The complete question is given below:

A small metal cylinder rests on a circular turntable that is rotating at a constant speed, as illustrated in the diagram (Figure 1) . The small metal cylinder has a mass of 0.20 kg , the coefficient of static friction between the cylinder and the turntable is 0.080, and the cylinder is located 0.15m from the center of the turntable. Take the magnitude of the acceleration due to gravity to be 9.81m/s^2 .

What is the maximum speed Vmax that the cylinder can move along its circular path without slipping off the turntable?

Answer:

300 Watt

Explanation:

power=(450/3)*2

The closest object that the eye can concentrate on is referred to as the near point. Typically, vision at a near point of 25 cm is regarded as “normal.”

So, because the power is negative, he won't be able to see the nearby objects quickly. This kind of victim is known as the metro pia, and it starts out right. Far-sightedness, or hyper metro pia, affects Raymond.

Sightedness for fire. The person in question is unable to stand on two feet as a result of this consequence. The farthest thing an average eye can image onto the retina is called the far point of a human eye.

Therefore, choose a prominent form behind the retina of the eye rather than focusing on the close items clearly. And to correct this flaw, a convex lens is utilized.

Learn more about lenses here:

https://brainly.com/question/28025799

#SPJ4

Senior citizens should perform balance exercises because it reduces the chances of falls, hence option B is correct.

The ability to maintain balance, however, deteriorates with age, and poor balance is a key contributor to falls in older persons.

A fall can cause serious injuries, including fractures, which can lead to chronic pain, reduced quality of life, disability, or even death.

Seniors' mobility will significantly improve if their exercise regimen is increased.

Therefore, being solid and steady can improve your general confidence, ease various health concerns, and lessen your danger of falling.

Learn more about exercises, here:

https://brainly.com/question/934019

#SPJ9