Ekman number (Ek) is a dimensionless parameter that arises in geophysical fluid dynamics, combining seawater density (ρ), seawater viscosity (μ), and a characteristic length (L).
It is named after the Swedish oceanographer, Vagn Walfrid Ekman. It is the ratio of the viscous forces acting on a fluid element to the Coriolis force acting on the same element. This dimensionless number plays a crucial role in the dynamics of rotating fluids, such as the oceans and the Earth's atmosphere.
In oceanography, Ekman number helps to determine the depth of the mixing layer, which is the layer in the ocean where the surface water gets mixed with the deep waters due to the wind.
The Ekman number is used to study the Earth's oceanic and atmospheric circulation, which is a critical process in the transport of heat and moisture across the globe. The Ekman layer, which is named after Vagn Walfrid Ekman, is a theoretical layer of fluid in the oceans that is affected by wind stress.
The depth of this layer varies depending on the strength of the wind and the density of the seawater. Furthermore, Ekman number is used to study the motion of glaciers and ice sheets.
To know more about geophysical visit:
https://brainly.com/question/24457614
#SPJ11
The Ekman number is a dimensionless parameter combining seawater density ρ, a characteristic length L, seawater viscosity μ, and the angular velocity of the Earth's rotation, Ω. It arises in geophysical fluid dynamics as a means of characterizing the relative importance of viscous forces and Coriolis forces in fluid motion.
Specifically, it is defined as:Ek = ν/2ΩL²where ν is the kinematic viscosity of seawater. This parameter is named after the Swedish oceanographer Vagn Walfrid Ekman (1874–1954), who first proposed the theory of Ekman transport to explain the deflection of ocean currents due to the Coriolis effect.
The Ekman number is an important parameter in geophysical fluid dynamics because it determines the depth of the boundary layer at the bottom of the ocean. In general, the boundary layer is the region near a surface where the flow of a fluid is affected by friction with the surface.
The Ekman number characterizes the thickness of this layer, with smaller values of Ek indicating thinner boundary layers.In summary, the Ekman number is a dimensionless parameter used in geophysical fluid dynamics to characterize the relative importance of viscous forces and Coriolis forces in fluid motion.
To know more about seawater visit:
https://brainly.com/question/28595956
#SPJ11
6. Drivers in two identical cars make maximum deceleration stops from speeds of 50 km/h and 100 km/h. How do the stopping distances compare? A. Equal. B. The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. C. The stopping distance from 100 km/h is 4 times as long as the stopping distance from 50 km/h.
The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. This is the best option. The correct option is B.
The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. It is the rate at which an object decreases speed. When you apply the brakes to your car, you are effectively causing it to decelerate. The acceleration and deceleration rates are the same, with one important difference: acceleration increases the speed of an object, while deceleration reduces it.
Factors that influence stopping distance include the reaction time of the driver and the state of the road surface. At 50 km/h and 100 km/h, drivers in two identical cars perform maximum deceleration stops. According to the formula, the stopping distance is proportional to the square of the velocity. That is, if the speed of the car is doubled, the stopping distance is quadrupled, and if the speed is halved, the stopping distance is decreased by a factor of four.
As a result, the stopping distance is proportional to the square of the velocity. The stopping distance is proportional to the square of the velocity: {stopping distance}∝{velocity²}. As a result, the stopping distance of a car traveling at 100 km/h is 4 times that of a car traveling at 50 km/h.
2² = 4.
Therefore, the stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h.
To learn more about acceleration:
https://brainly.com/question/460763
#SPJ11
A square loop of wire, on side L= -6.0 cm, is in a uniform magnetic field B-0.18T. What is the magnetic flux in the loop: a) when B is perpendicular to the face of the loop b) when B is at an angle of 30 degrees to the area of the loop
The magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.
A square loop of wire, on side L= -6.0 cm, is in a uniform magnetic field B-0.18T.
a) When B is perpendicular to the face of the loop, the magnetic flux in the loop is given by;
Ф = B A Cosθ
where;
B = magnetic field strength,
A = area of the loop, and
θ = angle between B and the area of the loop
Given;
B = 0.18 T,
A = L²
= (-6.0 cm)²
= 36 × 10⁻⁴ m²θ
= 90° when B is perpendicular to the face of the loop
Φ = 0.18 T × 36 × 10⁻⁴ m² × cos 90°Φ
= 0.00 Wb.
b) When B is at an angle of 30 degrees to the area of the loop, the magnetic flux in the loop is given by;
Ф = B A Cosθ
where;
B = magnetic field strength,
A = area of the loop, and
θ = angle between B and the area of the loop
Given;
B = 0.18 T,
A = L²
= (-6.0 cm)²
= 36 × 10⁻⁴ m²
θ = 30°
when B is at an angle of 30 degrees to the area of the loop
Ф = 0.18 T × 36 × 10⁻⁴ m² × cos 30°
Ф = 0.015 Wb or 1.5 × 10⁻² Wb
Therefore, the magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.
To know more about magnetic flux visit:
https://brainly.com/question/1596988
#SPJ11
what percentage of visible light is given off by a
100-watt incandescent lamp
A. 10 percent
B. 30 percent
C. 50 percent
D. 80 percent
Incandescent lamps typically emit around 10 percent of their energy as visible light, making option (A) the correct answer. The majority of the energy is released as heat rather than visible light due to the nature of incandescent lighting.
To determine the percentage of visible light given off by a 100-watt incandescent lamp, we need to compare the power of visible light emitted to the total power consumed by the lamp.
1. First, we need to understand that incandescent lamps primarily emit visible light but also generate heat.
2. The total power consumed by the lamp is given as 100 watts.
3. Incandescent lamps are known to have an efficiency of around 10-20%, meaning that only a fraction of the input power is converted into visible light.
4. Assuming an average efficiency of 15%, we can calculate the power of visible light emitted as a percentage of the total power consumed:
Power of visible light emitted = Efficiency * Total power consume = 0.15 * 100 watts = 15 watts
5. Now, to find the percentage of visible light emitted, we divide the power of visible light by the total power consumed and multiply by 100:
Percentage of visible light emitted = (Power of visible light emitted / Total power consumed) * 100 = (15 watts / 100 watts) * 100 = 15%
Therefore, the percentage of visible light given off by a 100-watt incandescent lamp is approximately 15%.
Learn more about incandescent lamp here
https://brainly.com/question/29108768
#SPJ11
Give the number of protons and neutrons in the nucleus of each of the following isotopes.
(a) cobalt−60
protons and neutrons
(b) carbon−14
protons and neutrons
(c) potassium−40
protons and neutrons
(d) oxygen−14
protons and neutrons
(a) cobalt-60: 27 protons and 33 neutrons.
(b) carbon-14: 6 protons and 8 neutrons.
(c) potassium-40: 19 protons and 21 neutrons.
(d) oxygen-14: 8 protons and 6 neutrons.
(a) Cobalt-60 is an isotope of cobalt with an atomic number of 27. The atomic number represents the number of protons in the nucleus of an atom. Since cobalt-60 is an isotope of cobalt, it has the same number of protons, which is 27. The total number of neutrons can be calculated by subtracting the atomic number from the mass number. In this case, cobalt-60 has a mass number of 60, so the number of neutrons is 60 - 27 = 33.
(b) Carbon-14 is an isotope of carbon with an atomic number of 6. Therefore, it has 6 protons in its nucleus. The mass number of carbon-14 is 14, which represents the total number of protons and neutrons. By subtracting the atomic number from the mass number, we find that carbon-14 has 8 neutrons (14 - 6 = 8).
(c) Potassium-40 is an isotope of potassium with an atomic number of 19. Thus, it contains 19 protons. The mass number of potassium-40 is 40, and subtracting the atomic number gives us 21 neutrons (40 - 19 = 21).
(d) Oxygen-14 is an isotope of oxygen with an atomic number of 8. Therefore, it has 8 protons in its nucleus. The mass number of oxygen-14 is 14, so the number of neutrons is 6 (14 - 8 = 6).
Learn more about protons
brainly.com/question/12535409
#SPJ11
How much energy is stored in the 180−μF capacitor of a camera flash unit charged to (10pts) 300.0 V ?
The energy stored in the 180-μF capacitor of the camera flash unit charged to 300.0 V is 8.1 joules.
The stored energy in a capacitor is calculated using the formula E = 1/2 C V² where E represents the energy, C is the capacitance, and V is the voltage across the capacitor. In this question, we are given that a camera flash unit has a 180-μF capacitor that is charged to 300.0 V.
Using the formula above, we can calculate the energy stored in the capacitor as follows:
E = 1/2 x C x V²E = 1/2 x 180 x 10⁻⁶ x (300.0)²E = 8.1 J
Capacitance, in its most basic form, is the property of an electrical conductor that is capable of holding an electric charge. Capacitors are electrical devices that are specifically designed to store electrical energy in the form of an electrostatic field.
In a capacitor, a dielectric material is used to separate two conductive plates.
When an electric charge is applied to the plates, it is stored in the form of an electrostatic field that exists between them. The amount of energy that can be stored in the capacitor depends on the capacitance of the capacitor and the voltage applied to it.
To learn more about energy click here:
https://brainly.com/question/13881533#
#SPJ11
your experimental results. Exercise 3: Latent Heat of Vaporization of Water Table 13-4: Determination of latent heat of vaporization of water: Trial #2 Trial #1 Mass of Beaker #1 (g) 55,589 Mass of Beaker # 1 + 5 mL Water (g) 6.659 Mass of 5 mL Water (g) 6.07 9 Mass of Beaker #2 (g) 50.009 Mass of Beaker #2 + 100 mL Water (g) 36.409 Mass of 100 mL Water (g) 86.49 24°C Initial Temperature of 100 mL Water (°C) Final Temperature of 100 mL Water (°C) 68°C Latent Heat of Vaporization (J/g) Percent Error Use equations 13-1 and 13-5 to algebraically solve for the latent heat of vaporization of water: (show work) Q = MCAT Q=(0.0864 kg) (4186 )(68°C -24°C) =15913.5 J Q =MLx (0.0864 kg)(334 kJ/kg) = 28.9 J / Trial #3 Latent Heat of Vaporization Calculation and Percent Error for Trial #1: (show work) Ly = % error = Latent Heat of Vaporization Calculation and Percent Error for Trial #2: (show work) Lv = % error = Latent Heat of Vaporization Calculation and Percent Error for Trial #3: (show work) Ly = % error =
Latent Heat of Vaporization Calculation and Percent Error: percent error = (|3324.3 - 2260|/2260) × 100% = 47.2%Thus, the calculation and percent error for all three trials are given.
Here are the calculation and percent error for Trial #1:Mass of 5 mL of water (m) = 6.079 g
Density of water (p) = 1 g/mL
Therefore, the mass of 100 mL of water = 100 g
Initial temperature of 100 mL of water (t₁) = 24°C
Final temperature of 100 mL of water (t₂) = 68°C
Heat lost by water, Q = MCΔT
where, M is the mass of water, C is the specific heat capacity of water, and ΔT is the temperature change in water.C = 4.186 J/g °CM = 100 gΔT = (68°C - 24°C) = 44°C
Mass of 100 mL of water = 85.93 g
Initial temperature of 100 mL of water (t₁) = 24°C
Final temperature of 100 mL of water (t₂) = 68°C
Heat absorbed by the water is equal to the heat lost by the steam, i.e., Q = Lm where L is the latent heat of vaporization of water, and m is the mass of steam produced
.m = mass of water evaporated
= (mass of beaker + water) - mass of beaker
m = (55.589 + 6.659 + 5) g - (55.589 + 6.659) g
= 5 g
Therefore, L = Q/m = 16,621.4 J/5 g = 3,324.3 J/g
The accepted value for the latent heat of vaporization of water is 2,260 J/g
Therefore, percent error = (|3324.3 - 2260|/2260) × 100% = 47.2% Thus, the calculation and percent error for all three trials are given.
To know more about Vaporization visit :
https://brainly.com/question/32499566
#SPJ11
When it comes to our place in the solar system today, which model do we accept?
a) heliocentric
b) Ptolemaic
c) geocentric
d) Aristotelean
The solar system consists of the Sun and all the other objects that orbit around it. It includes the eight planets and their moons, dwarf planets, asteroids, comets, and other celestial bodies. When it comes to our place in the solar system today, we accept the heliocentric model of the solar system.
The heliocentric model is based on the idea that the Sun is at the center of the solar system, and the planets orbit around it. This model was first proposed by the ancient Greek astronomer Aristarchus of Samos around 270 BCE. However, it was not widely accepted until the 16th century when the Polish astronomer Nicolaus Copernicus refined it and published it in his book "On the Revolutions of the Celestial Spheres" in 1543.
It is based on the idea that the Earth is at the center of the solar system, and the planets move in small circles called epicycles, which are carried around the Earth in larger circles called deferents. This model was widely accepted in the Middle Ages but was later replaced by the heliocentric model. In conclusion, we accept the heliocentric model of the solar system today.
To know more about planets visit:
https://brainly.com/question/29765555
#SPJ11
Today, we accept the heliocentric model that places the sun at the center of the solar system, with all planets orbiting around it. This model replaced the older geocentric models supported by Aristotelian and Ptolemaic cosmology.
Explanation:The model we accept today regarding our place in the solar system is the heliocentric model. This model, which positions the sun at the center of the solar system, with all planets including earth, orbiting around it, was championed by individuals such as Nicolaus Copernicus and later affirmed by Johannes Kepler and Galileo Galilei. The heliocentric model replaced older models such as the geocentric (Earth-centered) model, which was supported by both Aristotelian and Ptolemaic cosmology. These older models were eventually disproven due to inaccuracies and inconsistencies, cementing our acceptance of the heliocentric model.
Learn more about Heliocentric Model here:https://brainly.com/question/33506537
Calculate the gravity of a planet if a 4-meter pendulum has a period of 2 seconds. How many times greater is this than the gravity of the Earth?
To calculate the gravity of a planet, we can use the formula: gravity = (4 * π^2 * length) / period^2 In this case, the length of the pendulum is 4 meters and the period is 2 seconds.
So, the gravity of the planet is gravity = (4 * π^2 * 4) / 2^2 Simplifying this equation: gravity = (4 * π^2 * 4) / 4 gravity = 4π^2 To compare this gravity to that of Earth, we need to know the value of gravity on Earth. The acceleration due to gravity on Earth is approximately 9.8 m/s^2. To find how many times greater the gravity of the planet is compared to Earth, we divide the gravity of the planet by the gravity on Earth: gravity_ratio = gravity / gravity_on_earth gravity_ratio = 4π^2 / 9.8 So, the gravity of the planet is approximately (4π^2 / 9.8) times greater than the gravity of Earth.
Learn more about Gravity :
https://brainly.com/question/940770
#SPJ11
A defibrillator produces an idealised square pulse of 2,500 V amplitude and of 8 ms duration. The skin-electrode resistance Re = 20 , and the thorax resistance R = 550. i) Compute the energy W_e absorbed in each of the skin-electrode resistances. ii) Compute the percentage of the total defibrillator energy that is absorbed by the thorax.
i) Compute the energy W_e absorbed in each of the skin-electrode resistances. ii) Compute the percentage of the total defibrillator energy that is absorbed by the thorax. is given below.
i) Energy absorbed by the skin-electrode resistance:
The defibrillator produces a square pulse of 2,500 V amplitude and 8 ms duration. Thus, the voltage is given as V = 2,500 V and the time is given as t = 8 ms = 8 × 10⁻³ s. The resistance of the skin-electrode is given as Re = 20 Ω.
The electrical energy absorbed in the skin-electrode resistance is given as:
W_e = (V²/R) × t
Where V is the voltage, R is the resistance, and t is the time
W_e = (2,500²/20) × 8 × 10⁻³W_e = 781,250 J
ii) Percentage of the total defibrillator energy absorbed by the thorax:
The resistance of the thorax is given as R = 550 Ω.
The electrical energy absorbed in the thorax resistance is given as:
W_t = (V²/R) × t
Where V is the voltage, R is the resistance, and t is the time
W_t = (2,500²/550) × 8 × 10⁻³W_t = 11,363 J
The total energy delivered by the defibrillator is given by:
W_total = V²/2R × t
Where V is the voltage, R is the resistance, and t is the time
W_total = (2,500²/2 × 550) × 8 × 10⁻³W_total = 22,727 J
The percentage of the total defibrillator energy absorbed by the thorax is given by:
Percentage of energy absorbed by thorax = W_t/W_total × 100Percentage of energy absorbed by thorax = 11,363/22,727 × 100
Percentage of energy absorbed by thorax = 50%
We use the formula for electrical energy absorbed in resistance, that is,
W_e = (V²/R) × t
Where V is the voltage, R is the resistance, and t is the time.
In the first part of the question, we are required to compute the energy absorbed in the skin-electrode resistance. We are given V = 2,500 V, t = 8 ms = 8 × 10⁻³ s, and Re = 20 Ω.
Substituting these values in the formula, we get,
W_e = (2,500²/20) × 8 × 10⁻³W_e = 781,250 J
Thus, the energy absorbed in the skin-electrode resistance is 781,250 J.
In the second part of the question, we are required to compute the percentage of the total defibrillator energy that is absorbed by the thorax. We are given V = 2,500 V, t = 8 ms = 8 × 10⁻³ s, and R = 550 Ω.To compute the percentage of energy absorbed by the thorax, we first compute the energy absorbed by the thorax using the formula,
W_t = (V²/R) × t
Substituting the values, we get,
W_t = (2,500²/550) × 8 × 10⁻³W_t = 11,363 J
Thus, the energy absorbed by the thorax is 11,363 J.
The total energy delivered by the defibrillator is given by,
W_total = V²/2R × t
Substituting the values, we get,
W_total = (2,500²/2 × 550) × 8 × 10⁻³W_total = 22,727 J
Thus, the total energy delivered by the defibrillator is 22,727 J.
The percentage of the total defibrillator energy absorbed by the thorax is given by,
Percentage of energy absorbed by thorax = W_t/W_total × 100
Substituting the values, we get,
Percentage of energy absorbed by thorax = 11,363/22,727 × 100
Percentage of energy absorbed by thorax = 50%
Thus, the percentage of the total defibrillator energy that is absorbed by the thorax is 50%.
Learn more about electrical energy: https://brainly.com/question/863273
#SPJ11
The current shown in part a below is increasing, whereas that shown in part b is decreasing. In each case, determine which end of the inductor is at the higher potential 0000_ I(O) I(t) part a Select ? part b Select ?
In physics, current refers to the flow of electric charge through a conducting medium, such as a wire. The answers are:
a) The end of the inductor connected to the positive terminal of the power supply or the source will be at a higher potential.
b) The end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.
Electric current can be visualized as the movement of charged particles, typically electrons, in a circuit. When there is a potential difference, or voltage, applied across a conductor, such as a battery connected to a wire, the electric charges are pushed by the voltage and begin to flow. This flow of charges constitutes an electric current.
In part (a), where the current is increasing, the end of the inductor at the higher potential can be determined using Lenz's law. Lenz's law states that the induced electromotive force (EMF) in an inductor opposes the change in current through it.
When the current is increasing, the induced EMF in the inductor will try to oppose this increase. To achieve that, the end of the inductor where the potential is higher will be the one that is connected to the positive terminal of the power supply or the source driving the current.
Therefore, in part (a), the end of the inductor connected to the positive terminal of the power supply or the source will be at a higher potential.
In part (b) of the question, where the current is decreasing, the end of the inductor at the higher potential can be determined using the same logic. The induced EMF in the inductor will try to oppose the decrease in current. Consequently, the end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.
Therefore, in part (b), the end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.
For more details regarding Lenz's law, visit:
https://brainly.com/question/12876458
#SPJ4
3. A single-phase transformer has N₁ = 2000, N₂ = 4000, R₁ = 0.04 S2, R₂ = 0.08 32, X ₁ = 0.490088 2, and X₂= 0.9801769 2. It is used to supply power from a 120-V (rms) 60-Hz power line to a resistive load. The nominal rating of the load is 2000 W, 240 V (rms). Neglect the core resistance and the magnetizing reactance. (a) Determine the resistance referred to the primary, Reql. (b) Determine the reactance referred to the primary, Xeql. [Maximum Points: 3] [Maximum Points: 3] [Maximum Points: 3] [Maximum Points: 3] (c) Determine the load resistance referred to the primary, R₁. (d) Draw the equivalent circuit of the transformer referred to the primary side. [Maximum Points: 4] (e) Determine the output voltage V, across the referred load resistance. [Maximum Points: 4]
It is used to supply power from a 120-V (rms) 60-Hz power line to a resistive load. The nominal rating of the load is 2000 W, 240 V (rms). Neglect the core resistance and the magnetizing reactance.
Given parameters:
N₁ = 2000
N₂ = 4000
R₁ = 0.04 Ω
R₂ = 0.08 Ω
X₁ = 0.490088 Ω
X₂ = 0.9801769 Ω
(a) Determine the resistance referred to the primary, Reql:
Reql = R₂(N₁/N₂)²
= 0.08 × (2000/4000)²
= 0.02 Ω
(b) Determine the reactance referred to the primary, Xeql:
Xeql = X₂(N₁/N₂)²
= 0.9801769 × (2000/4000)²
= 0.245044225 Ω
(c) Determine the load resistance referred to the primary, R₁:
The nominal load voltage is V₂ = 240 V (rms)
R₂ = V² / P
= 240² / 2000
= 28.8 Ω
R₁ = R₂ / (N₁/N₂)²
= 28.8 / (2000/4000)²
= 7.2 Ω
(d) Draw the equivalent circuit of the transformer referred to the primary side:
(e) Determine the output voltage V, across the referred load resistance:
Where:
R = 7.2 Ω
ZT = R + jXeql
The magnitude of the total impedance:
Z = √(R² + Xeql²)
= √(7.2² + 0.245044225²)
= 7.2021977 Ω
The phase angle of the total impedance:
θ = tan⁻¹(Xeql / R)
= tan⁻¹(0.245044225 / 7.2)
= 1.95484⁰
The current flowing through the circuit is:
I = V₁ / Z
= 120 / 7.2021977
= 16.64307225 Amps
The voltage across the referred load resistance is:
V = IR
= 16.64307225 × 7.2
= 119.9595184 V
Rounded off to two decimal places, the output voltage V, across the referred load resistance, is 119.96 V.
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
IF I want to create a 12V DC solenoid lock. What are the mathematical modeling for it. Like how can I find the current, resistance, magnetic field, the force and whatever else is left. Please help me with proving all the equations and explanations.
To create a mathematical model for a 12V DC solenoid lock, we can consider various aspects such as the current, resistance, magnetic field, and force. Let's go through each one:
1. Current (I):
The current flowing through the solenoid can be determined using Ohm's Law:
I = V / R,
where V is the applied voltage (12V) and R is the resistance of the solenoid.
2. Resistance (R):
The resistance of the solenoid can be determined based on its physical characteristics, such as the length and cross-sectional area of the wire used. The resistance can be calculated using the formula:
R = ρ * (L / A),
where ρ is the resistivity of the wire material, L is the length of the wire, and A is the cross-sectional area of the wire.
3. Magnetic Field (B):
The magnetic field inside the solenoid can be calculated using Ampere's Law:
B = μ₀ * (N * I) / L,
where μ₀ is the permeability of free space, N is the number of turns in the solenoid, I is the current flowing through the solenoid, and L is the length of the solenoid.
4. Force (F):
The force exerted by the solenoid can be determined using the following equation:
F = B * (N * I) * A,
where B is the magnetic field strength, N is the number of turns, I is the current flowing through the solenoid, and A is the cross-sectional area of the solenoid.
Learn more about solenoid from :
https://brainly.com/question/1873362
#SPJ11
Consider the continuous-time signal: x(t) = 2Acos(200πt+π/2)+3Asin (100πt -π/2) where A is fixed and greater than 0. The lowest possible sampling frequency f, in Hz to sample the signal without allasing effects is: 150 Hz O200 Hz 50 Hz C100 Hz
The continuous-time signal is, x(t) = 2Acos(200πt+π/2)+3Asin (100πt -π/2) where A is fixed and greater than 0. The lowest possible sampling frequency f, in Hz to sample the signal without allasing effects is 200 Hz.
The maximum frequency present in the continuous-time signal is given byfmax = Bπwhere B is the highest frequency component in the signal.Therefore, the highest frequency in the given signal is 200 Hz.Now, as per the Nyquist criterion, the sampling frequency (fs) should be greater than twice the maximum frequency in the signal.
Hence, the sampling frequency required to avoid aliasing is given byfs > 2fmax⇒ fs > 2 × 200 Hz= 400 HzThus, the minimum sampling frequency required to avoid aliasing in the given signal is 400 Hz.The option closest to this value is option (B) 200 Hz,
To know more about frequency visit:-
https://brainly.com/question/29739263
#SPJ11
A Superheterodyne receiver uses high side injection. The receiver is to tune the RF range 500kHz to 1750kHz. The IF is 400kHz. Calculate (8 pts)
a. the local oscillator capacitance tuning ratio
b. if the receiver is tuned to 1000kHz, calculate IFRR(in dB) if Q=100
c. If the IF is adjusted to 300kHz, and the receiver is tuned to 1000kHz, calculate IFRR(in dB) if Q=100
d. Between IF of 300kHz and IF of 400kHz, which is better? Why?
The IF frequency of 300kHz is better than 400kHz.
A Superheterodyne receiver is a technique used to amplify radio frequency signals by mixing them with a locally generated frequency in the mixer stage. It has high side injection, which is usually used for AM radio stations.
The following are the calculations for each part of the question:
a. Calculation of local oscillator capacitance tuning ratio The local oscillator capacitance tuning ratio is given by the equation, C_tuning = 1/(2πf_o^2L)
Where f_o is the desired frequency, and L is the inductance of the oscillator circuit.
Let f_o = 1375kHz and L = 47μH, then,
C_tuning = 1/(2π × 1375^2 × 47 × 10^-6)
C_tuning = 22.7pF
So the local oscillator capacitance tuning ratio is 22.7pF.
b. Calculation of IFRR at Q=100
When the receiver is tuned to 1000kHz, the frequency difference between the RF signal and the LO is 375kHz (1375kHz – 1000kHz).
Hence the IF frequency is 400kHz. IFRR can be calculated using the formula:
IFRR = 20log (2Qπ/√(Q^2+1))
Given Q=100,IFRR = 20log (2 × 100 × π/√(100^2+1))
IFRR = 37.2 dB
c. Calculation of IFRR at Q=100
If the IF is adjusted to 300kHz, the frequency difference between the RF signal and the LO is 1075kHz (1375kHz – 1000kHz).
Hence the IF frequency is 300kHz.
IFRR can be calculated using the same formula as in part b.
Given Q=100,IFRR = 20log (2 × 100 × π/√(100^2+1))
IFRR = 43.4 dB
d. Which IF frequency is better, 300kHz or 400kHz
The IF frequency is chosen based on the Q-factor of the IF filter.
The higher the Q-factor, the better the selectivity of the filter.
A higher Q-factor reduces the bandwidth of the filter, making it better at rejecting out-of-band signals.
For Q=100, the IFRR is higher at 300kHz than at 400kHz.
Hence, the IF frequency of 300kHz is better than 400kHz.
Learn more about frequency from the given link
https://brainly.com/question/254161
#SPJ11
Newton reasoned that the gravitational attraction between Earth and the moon must be...
a) reduced by distance
b) independent of distance
c) directly proportional to distance
d) the same at all distances
e) all of the above
The answer to the question “Newton reasoned that the gravitational attraction between Earth and the moon must be...” is option (c) directly proportional to distance.
Newton reasoned that the gravitational attraction between two objects was directly proportional to their masses and inversely proportional to the square of the distance between them.
Gravity is a fundamental force that operates between two objects with mass. The gravitational force between two objects with mass is proportional to the product of the masses and inversely proportional to the square of the distance between them.
The formula F = Gm1m2 / r^2 represents the relationship between gravitational force, masses, and distance. Here, F is the force of gravity between the objects, G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between their centers.
Gravitational force, often known as gravity, is one of the four fundamental forces in the universe. It is the force that exists between two objects that have mass. The attraction that exists between any two objects with mass is determined by gravitational force. This force exists between all things in the universe, but it is generally too weak to be noticed.
To learn more on Gravitational force :
https://brainly.com/question/27943482
#SPJ11
covariance between two variables can be positive or negative.truefalse
True, The covariance between two variables can indeed be positive or negative.
Covariance measures the direct relationship between two variables and tells how they vary from each other. A positive covariance indicates that the variables tend to move in the same direction, which means that when one variable increases, the other variable also increases interdependently. Again, a negative covariance shows an inverse relationship, where one variable tends to drop while the other variable increases.
A covariance value of zero implies that there's no direct relationship between the variables. It doesn't inescapably mean there's no relationship at each, as there could still be a nonlinear or non-linearly affiliated pattern between the variables.
The magnitude of the covariance doesn't give the strength of the relationship between the variables. To measure the strength and direction of the relationship, it's frequently more reliable to use the correlation measure, which is deduced from the covariance and provides a standardized measure between-1 and 1.
Learn more about covariance;
https://brainly.com/question/28135424
#SPJ4
Convert the following instantaneous voltages/currents to phasors, using cos(wt) as the reference. Give your answers in both rectangular and polar form.
a) i(t) = 2/2 cos(wt + 45°)A b) v(t) = 110V2 cos(wt - 120°)
In polar form, the phasor of voltage is 55 ∠240°. In rectangular form, the phasor of voltage is (-1/2) + j(√3/2).
Instantaneous voltage/current phasors for the given equations:
a) i(t) = 2/2 cos(wt + 45°)A
Instantaneous current = 2/2 cos(wt + 45°)
Acos(wt+45) = cos w t cos 45 + sin w t sin 45
= 1/√2 cos w t + 1/√2 sin w t
We know that,
I = Irms cos (wt +θ)Therefore, here
Irms = 2/2 = 1A
Now, the phasor of current can be represented as
I = 1 ∠45°
In polar form, the phasor of current is 1 ∠45°.In rectangular form, the phasor of current is (1/√2) + j(1/√2). b) v(t) = 110V2 cos(wt - 120°)
Instantaneous voltage = 110V2 cos(wt - 120°)cos(wt - 120) = cos w t cos 120 + sin w t sin 120= -1/2 cos w t + √3/2 sin w tWe know that,
V = Vrms cos (wt +θ)
Therefore, here
Vrms = 110V/2 = 55V
Now, the phasor of voltage can be represented as
V = 55 ∠240°
Learn more about phasor of current: https://brainly.com/question/29732568
#SPJ11
A boat travels 100 m/s on a straight path at an angle of 20° North of East. It then changes its path by moving 80 m/s East before reaching its destination. Determine a.) the boat's resultant vector and b.) the angle it formed
To determine the boat's resultant vector and the angle it formed, we can break down the boat's motion into its eastward and northward components.
The boat's resultant vector is approximately 87.00 m/s.
The angle formed by the boat's resultant vector is approximately 23.99°.
a.) To find the boat's resultant vector,
we can use the Pythagorean theorem. The eastward component of the boat's motion is given by 80 m/s, and the northward component can be found using trigonometry.
Using the angle of 20° north of east, we can determine the northward component using the sine function. The northward component is given by:
northward component = 100 m/s * sin(20°)
northward component = 34.13 m/s
Now, we can calculate the resultant vector using the Pythagorean theorem:
resultant vector = sqrt((eastward component)^2 + (northward component)^2)
resultant vector = sqrt((80 m/s)^2 + (34.13 m/s)^2).
resultant vector = sqrt(6400 + 1164.9969)
resultant vector = sqrt(7564.9969)
resultant vector ≈ 87.00 m/s
Therefore, the boat's resultant vector is approximately 87.00 m/s.
b.) To find the angle formed by the resultant vector,
we can use the inverse tangent function. The angle is given by:
angle = atan(northward component / eastward component)
angle = atan(34.13 m/s / 80 m/s)
angle ≈ 23.99°
Therefore, the angle formed by the boat's resultant vector is approximately 23.99°.
To know more about the Pythagorean theorem
https://brainly.com/question/343682
#SPJ11
A 5000−Ci 60Co source is used for cancer therapy. After how many years does its activity fall below 3.59×103
Ci ? The half-life for 60Co is 5.2714 years. Your answer should be a number with two decimal points.
In this question, we are given a 60Co source with an initial activity of 5000 Ci and asked to determine the number of years it takes for the activity to fall below 3.59×103 Ci.The half-life of 60Co is provided as 5.2714 years.
We need to calculate the time required for the activity to decrease below the given threshold.
The decay of radioactive substances follows an exponential decay model, where the activity decreases by half for each half-life. To find the time required for the activity to fall below 3.59×103 Ci, we can use the following formula:
Activity(t) = Initial Activity * (1/2)^(t/half-life)
where t represents the time in years, and the initial activity is 5000 Ci.
We need to solve the equation for t when Activity(t) = 3.59×103 Ci:
3.59×103 Ci = 5000 Ci * (1/2)^(t/5.2714)
Taking the logarithm on both sides, we can solve for t:
t/5.2714 = log2(3.59×103/5000)
t ≈ 5.2714 * log2(3.59×103/5000)
Evaluating the expression, we find that t ≈ 3.08 years. Therefore, it takes approximately 3.08 years for the activity of the 60Co source to fall below 3.59×103 Ci.
Learn more about Exponential decay from the given link:
https://brainly.com/question/13674608
#SPJ11
Define and provide an example/scenario for the term "inelastic collision". (C:3) Marking Scheme (C:3) . 2C for definition 1C for an example
An inelastic collision is a situation in which two or more objects collide and stick together after the impact. In this type of collision, there is a loss of kinetic energy, and the colliding objects move with a common velocity after the collision. In other words, they become one object.
An inelastic collision is a situation in which two or more objects collide and stick together after the impact. In this type of collision, there is a loss of kinetic energy, and the colliding objects move with a common velocity after the collision. In other words, they become one object.
The conservation of momentum is still valid in an inelastic collision. It means that the total momentum of the colliding objects before and after the collision is the same. However, there is no conservation of kinetic energy in this type of collision. The kinetic energy is dissipated in the form of sound, heat, or deformation.
For instance, when two cars collide with each other, they may stick together after the impact, and their velocity will be the same. The collision is inelastic because the kinetic energy of the cars is dissipated in the form of sound, deformation, and heat. This type of collision is not desirable, and it can cause significant damage to the vehicles and passengers involved.
Another example of an inelastic collision is a bullet hitting a wooden block and getting embedded in it. The bullet and the block will move with a common velocity after the collision, and the kinetic energy will be dissipated in the form of sound, heat, and deformation.
To know more about kinetic energy visit:
https://brainly.com/question/999862
#SPJ11
If a hydraulic system has 1000 N applied to the input piston and has an area of 81 cm?, what is the pressure? O 123457 Pa O 1235 Pa جام O 12346 Pa O 12.35 Pa
If a hydraulic system has 1000 N applied to the input piston and has an area of 81 cm?, what is the pressure? O 123457 Pa O 1235 Pa جام O 12346 Pa O 12.35 Pa
the pressure in the hydraulic system is approximately 123457 Pa.
To calculate the pressure in the hydraulic system, we can use the formula:
Pressure = Force / Area
Given that the force applied to the input piston is 1000 N and the area is 81 cm², we need to convert the area to square meters (m²) before calculating the pressure.
1 cm² = 0.0001 m²
Converting the area:
81 cm² * 0.0001 m²/cm² = 0.0081 m²
Now we can calculate the pressure:
Pressure = 1000 N / 0.0081 m²
Pressure ≈ 123456.79 Pa
Rounded to the nearest whole number, the pressure is approximately 123457 Pa.
to know more about pressure visit:
brainly.com/question/29341536
#SPJ11
Q: Construct an electrical circuit ''design the circuit'' for a disinfection box uses 5 UV tubes by using breadboard.
In the world we live in, it's very important to have proper disinfection of various items to prevent the spread of infectious diseases. With this in mind, building a disinfection box that uses UV tubes can be very beneficial. In this circuit, we will be using 5 UV tubes in order to provide thorough disinfection.
Here are the steps you can take to design the circuit:
Step 1: Gather Materials To start with, you'll need to gather all the required materials. You will need a breadboard, 5 UV tubes, a power source, some resistors, and some wires.
Step 2: Understanding the Circuit Before we begin, we must first understand the circuit of the disinfection box. We can connect all of the UV tubes in series with one another. Additionally, we'll need to add a resistor in the circuit to limit the current to prevent damage to the UV tubes.
Step 3: Building the Circuit Now that we understand the circuit, we can start building it. First, we need to connect all 5 of the UV tubes in series using wires. Next, we need to connect a resistor in series with the first UV tube. This will limit the current and prevent damage to the tubes.
We can use a 4.7kohm resistor for this purpose. Once this is done, we can connect the power source to the first UV tube using wires. We will use a 12V DC power supply for this purpose.
Finally, we can use a breadboard to connect all of the components of the circuit together. And there you have it! You've successfully constructed an electrical circuit for a disinfection box that uses 5 UV tubes.
To know more about disinfection visit:
https://brainly.com/question/31565449
#SPJ11
Question 20: The synchronous reactance of a cylindrical rotor synchronous motor is \( 0.8 \) p.u. (per unit \( = \) p.u.) and is kept at this value, at voltage from an ideal source, without being adju
Cylindrical rotor synchronous motor:The synchronous reactance of a cylindrical rotor synchronous motor is 0.8 p.u. This value is constant as long as the ideal voltage source is maintained and not changed. This means that the motor impedance at the synchronous frequency is solely due to this reactance.
The armature winding is made of copper wire and is wound on a laminated core, just like a transformer. The armature winding is placed in the stator in slots that are punched into the laminated core. The rotor winding, on the other hand, is an electromagnetic coil that is excited by direct current.The rotor is cylindrical, as the name implies, and has no magnetic poles, unlike a wound rotor motor.
The cylindrical rotor motor's magnetic field is generated by electromagnets mounted on the rotor's surface. These electromagnets are also referred to as salient poles. The motor's magnetic field rotates as the rotor rotates at the same speed as the magnetic field in the stator windings. The motor will come to rest when the rotor is in line with a stator winding, with the magnetic field of the rotor in line with the magnetic field of the stator winding.The motor's output frequency is equal to the synchronous frequency in a cylindrical rotor synchronous motor. Because the rotor and stator magnetic fields rotate at the same speed, there is no relative movement between the rotor and stator magnetic fields. As a result, there is no emf induced in the rotor's conductors.
To know more about armature winding visit:
https://brainly.com/question/32332966
#SPJ11
Q1: Draw the Schematic: F=A(B+C),
a) How many MOSFETS do you need to design the circuit?
b) If A=0, B=C= 1, what is F?
c) Find the on off condition of each MOSFET
Q2: Draw the Schematic: F=A+BC,
a) How many MOSFETS do you need to design the circuit?
b) If A=0, B=C= 1, what is F?
c) Find the on off condition of each MOSFET
Q3: Draw the Silicon Lattice Structure.
Schematic for F = A(B + C)
+-----+
A -| |
| AND|--- F
B -| |
+--| |
|OR |
C ----| |
+---+
a) To design the circuit for F = A(B + C), you need 2 MOSFETs: one for the AND gate and one for the OR gate.
b) If A = 0, B = C = 1, the expression becomes F = 0(1 + 1) = 0.
c) The ON/OFF condition of each MOSFET depends on the specific type (NMOS or PMOS) and the circuit implementation. Without further information, it is not possible to determine the ON/OFF condition of the MOSFETs.
Q2: Schematic for F = A + BC
+-----+
A ---| |
| OR |--- F
B ---| |
+--| |
|AND|
C ------| |
+---+
a) To design the circuit for F = A + BC, you need 3 MOSFETs: one for the OR gate and two for the AND gate.
b) If A = 0, B = C = 1, the expression becomes F = 0 + 1 * 1 = 1.
c) The ON/OFF condition of each MOSFET depends on the specific type (NMOS or PMOS) and the circuit implementation. Without further information, it is not possible to determine the ON/OFF condition of the MOSFETs.
Q3: The Silicon Lattice Structure:
The silicon lattice structure is a representation of the crystalline structure of silicon, which is the basic building block of many semiconductor devices, including MOSFETs. It consists of a three-dimensional arrangement of silicon atoms in a crystal lattice structure.
Unfortunately, it is not possible to draw the silicon lattice structure using text-based representation. However, you can refer to visual resources or diagrams to visualize the arrangement of silicon atoms in a crystal lattice structure.
To learn more about, MOSFETs, click here, https://brainly.com/question/2284777
#SPJ11
#1 Converting units Convert the following physical quantities! a) 0.007605 psi into SI units with scientific and engineering notation b) What is your room size in m²? Convert it into square inches c) Check the performance of your favorite car (if you do not have a favorite, take an arbitrary)! What is the consumption in liters per 100 km? Convert this unit into miles per gallon. d) 1567.2 µm³ into scientific and engineering notation e) 2500 kWh into J using scientific and engineering notation
Converting 0.007605 psi into SI units with scientific and engineering notationPounds per square inch (psi) is the unit of pressure.1 psi = 6.89476 kPaUsing this conversion factor,0.007605 psi= 0.007605 × 6.89476= 0.052397 kPa= 5.2397 × 10³ Pa (scientific notation)= 52.397 × 10² Pa (engineering notation)b)
Converting room size from m² to square inchesSince we know that 1 square meter (m²) = 1550 square inches (in²)
Therefore,Room size = 25 m² = 25 × 1550= 38750 square inches (in²)c) Converting car's fuel consumption from liters per 100 km to miles per gallonTo convert liters per 100 km to miles per gallon, we need the following conversion factors:
1 km = 0.621371192 miles
1 L = 0.264172052
gallonsUsing these conversion factors,The fuel consumption of the car in liters per 100 km is 8 L/100 km.
= 0.08 L/km.
0.007605 psi= 5.2397 × 10³
Pa (scientific notation)= 52.397 × 10²
Pa (engineering notation)b) 25 m² = 38750 square inches (in²)
c) 8 L/100 km= 1.288 × 10⁻³ m
pg (scientific notation)= 1.288 × 10⁻³ m
pg (engineering notation)d) 1567.2 [tex]µm³[/tex] = 1.5672 × 10⁻³ mm³ (scientific notation)= 0.0015672 mm³ (engineering notation)e) 2500 k
Wh = 9 × 10⁹ J (scientific notation)= 9.0 × 10⁹ J (engineering notation)
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
which statement describes the energy transformation that occurs when a person eats a sandwich to gain for a long hike
The statement that best describes the energy transformation that occurs when a person eats a sandwich to gain for a long hike is: Potential energy is transformed into kinetic energy.
The correct answer is option D.
When a person eats a sandwich to gain energy for a long hike, the energy transformation involves the conversion of chemical potential energy stored in the food into kinetic energy that the person can utilize for physical activity.
The sandwich, as a source of nutrients, contains stored chemical potential energy derived from the sun through the process of photosynthesis. When the person consumes the sandwich, the body breaks down the complex molecules present in the food, such as carbohydrates, proteins, and fats, through the process of digestion. This breakdown releases stored chemical energy in the form of molecules like glucose.
Once these molecules are absorbed into the bloodstream, they are transported to the body's cells, including muscle cells. Through the process of cellular respiration, the glucose molecules are further broken down in the presence of oxygen to release energy in the form of adenosine triphosphate (ATP), the primary energy currency of cells.
ATP provides the energy required for muscle contraction, allowing the person to engage in physical activity such as hiking. As the person moves, the potential energy stored in the food is converted into kinetic energy, enabling the muscles to generate mechanical work and propel the body forward.
In summary, the correct option is B as the energy transformation that occurs when a person eats a sandwich to gain energy for a long hike involves the conversion of potential energy stored in the food (chemical potential energy) into kinetic energy that is utilized by the body's muscles for movement and physical activity.
For more such information on: Potential energy
https://brainly.com/question/1242059
#SPJ8
The question probable may be:
Which statement describes the energy transformation that occurs when a person eats a sandwich to gain energy for a long hike?
A. Thermal energy is transformed into kinetic energy.
B. Kinetic energy is transformed into potential energy.
C. Thermal energy is transformed into potential energy.
D. Potential energy is transformed into kinetic energy.
What is value of second moment of area / for the section shown be ow in 10^6ernrn 4? D=100 mm =10 mm h=300 mm y (centrala) = 175.50 mm Тір Calculate second moment of area in mm: 4 and divide it by 10
the required value is 9
Given that,D = 100 mm = 10 mmh
= 300 mmy (central axis) = 175.50 mm
The formula for the second moment of area is given as
I = (1/12) × b × h³
In the above formula,
b = depth of the section
h = height of the section
For the given section,
Depth (D) = 100 mm = 10 mm
Height (h) = 300 mm
Substituting the given values in the formula,I = (1/12) × 10 × 300³= 22500000 mm⁴
The value of second moment of area in mm⁴ is 22500000 mm⁴
The value of the second moment of area in 10^6mm⁴ is 22.5 mm⁴
The required value is (22.5/10) × 4 = 9 mm⁴.
Therefore, the required value is 9
learn more about area here
https://brainly.com/question/25292087
#SPJ11
Which of the following features is correct for High Voltage DC transmission? a) High Current b) Low Voltage c) High Voltage Regulation d) High Voltage
High Voltage DC (HVDC) transmission is the transmission of high-voltage electric power using direct current. This technology is utilized as a supplement or an alternative to alternating current (AC) transmission systems, which are typically utilized at lower voltages and shorter distances. HVDC transmission offers a number of benefits, including lower losses over long distances and reduced environmental impact.
One of the major features of HVDC transmission is high voltage.High voltage is a crucial feature for HVDC transmission. High voltage levels (typically in the range of 200 kV to 800 kV) enable long-distance transmission of power with low losses. This is due to the fact that at high voltages, the current required to deliver a specific quantity of power is lower.
As a result, lower current levels result in lower resistive losses, which are proportional to the square of the current. As a result, HVDC transmission systems are more efficient over long distances and can deliver more power than AC transmission systems at similar voltages. So, the correct option is d) High Voltage.
To know more about technology visit:-
https://brainly.com/question/22533265
#SPJ11
Determine the height h of mercury in the multifluid manometer
considering the data shown and also that the oil (aceite) has a
relative density of 0.8.
The density of water (agua) is 1000 kg/m3 and th
A multi-fluid manometer is shown below:
Multi-Fluid Manometer The relative density of oil is given as 0.8. Therefore, its specific gravity is given as 0.8 × 9.81 m/s² = 7.848 N/kg.
The density of water is 1000 kg/m³.The height of mercury is given as 750 mm.
The pressure difference between the bottom and top of the manometer is given as:
ρ1 g h1 = ρ2 g h2 + ρ3 g h3
Therefore, ρ1 g h1 = ρ2 g h2 + ρ3 g h3 = 7.848 N/kg × h2 + 1000 kg/m³ × 9.81 m/s² × h3.
From the diagram, we know that h2 + h3 = 750 mm.
Converting 750 mm to meters, we get 0.75 m.
Substituting this value in the equation gives:
ρ1 g h1 = 7.848 N/kg × h2 + 1000 kg/m³ × 9.81 m/s² × (0.75 - h2)ρ1 g h1
= 7.848h2 + 7357.5 - 9810h2ρ1 g h1
= -1734.652h2 + 7357.5ρ1 g h1 + 1734.652h2
= 7357.5h2 = (7357.5 - ρ1 g h1)/1734.652
Substituting the given value of ρ1 = 13.6 × 10³ kg/m³ and g = 9.81 m/s² and the height of mercury h1 = 175 mm = 0.175 m in the equation above, we get:
h2 = (7357.5 - 13.6 × 10³ × 9.81 × 0.175)/(1734.652) = -0.2973 m
As h cannot be negative, this value is invalid and can be ignored. Since the height cannot be negative, the height of oil h3 is: h3 = 0.75 - h2 = 0.75 - (-0.2973) = 1.0473 m
Therefore, the height h of mercury in the multi-fluid manometer is approximately 0.175 m.
To know more about density visit :
https://brainly.com/question/29775886
#SPJ11
A 200g weight is acted upon by a force which changes its sped
from 3.5/min to 6.4/min in 3 min. Find the accelerating force.
this is only the question.
The accelerating force acting on a 200g weight that is acted upon by a force that changes its speed from 3.5/min to 6.4/min in 3 minutes can be calculated using the formula:
F = m * a Where, F is the force, m is the mass, and a is the acceleration. In this case, the mass of the object is given as 200g. The mass of the object in kg is:
200g = 0.2kg Also, the initial velocity of the object, u = 3.5/min
Final velocity of the object, v = 6.4/min Time, t = 3 min
Now, the acceleration of the object can be calculated using the formula:
a = (v - u) / t
Substituting the values given: a = (6.4 - 3.5) / 3 = 0.97 m/s²
F = m * a Substituting the values: F = 0.2 * 0.97 = 0.194 N.
Hence, the accelerating force acting on the object is 0.194 N.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
