QUESTION 2 A machinist turns the power on to a grinding wheel, at rest, at time t = 0 s. The wheel accelerates uniformly for 10 s and reaches the operating angular velocity of 42 rad/s. The wheel is run at that angular velocity for 32 s and then power is shut off. The wheel slows down uniformly at 2.2 rad's until the wheel stops. In this situation, the total number of revolutions made by the wheel is closest to: o 210 250 310 © 280 410 QUESTION 2 A 0.24 kg blob of clay is thrown at a wall with an initial velocity of 20 m/s. If the clay comes to a stop in 91 ms, what is the average force experienced by the clay? 45 N 33 N 53 N 64 N QUESTION 1 At time t = 0 s, a wheel has an angular displacement of zero radians and an angular velocity of +26 rad/s. The wheel has a constant acceleration of 0.43 rad's2 In this situation, the time t (after t=0 s), at which the kinetic energy of the wheel is twice the initial value, is closest to: O 150 s O 60 s 130 s O 85 s O 110 s

Converting 0.007605 psi into SI units with scientific and engineering notationPounds per square inch (psi) is the unit of pressure.1 psi = 6.89476 kPaUsing this conversion factor,0.007605 psi= 0.007605 × 6.89476= 0.052397 kPa= 5.2397 × 10³ Pa (scientific notation)= 52.397 × 10² Pa (engineering notation)b)

Converting room size from m² to square inchesSince we know that 1 square meter (m²) = 1550 square inches (in²)

Therefore,Room size = 25 m² = 25 × 1550= 38750 square inches (in²)c) Converting car's fuel consumption from liters per 100 km to miles per gallonTo convert liters per 100 km to miles per gallon, we need the following conversion factors:

1 km = 0.621371192 miles

1 L = 0.264172052

gallonsUsing these conversion factors,The fuel consumption of the car in liters per 100 km is 8 L/100 km.

= 0.08 L/km.

0.007605 psi= 5.2397 × 10³

Pa (scientific notation)= 52.397 × 10²

Pa (engineering notation)b) 25 m² = 38750 square inches (in²)

c) 8 L/100 km= 1.288 × 10⁻³ m

pg (scientific notation)= 1.288 × 10⁻³ m

pg (engineering notation)d) 1567.2 [tex]µm³[/tex] = 1.5672 × 10⁻³ mm³ (scientific notation)= 0.0015672 mm³ (engineering notation)e) 2500 k

Wh = 9 × 10⁹ J (scientific notation)= 9.0 × 10⁹ J (engineering notation)

To know more about pressure visit:

https://brainly.com/question/30673967

#SPJ11

A multi-fluid manometer is shown below:

Multi-Fluid Manometer The relative density of oil is given as 0.8. Therefore, its specific gravity is given as 0.8 × 9.81 m/s² = 7.848 N/kg.

The density of water is 1000 kg/m³.The height of mercury is given as 750 mm.

The pressure difference between the bottom and top of the manometer is given as:

ρ1 g h1 = ρ2 g h2 + ρ3 g h3

Therefore, ρ1 g h1 = ρ2 g h2 + ρ3 g h3 = 7.848 N/kg × h2 + 1000 kg/m³ × 9.81 m/s² × h3.

From the diagram, we know that h2 + h3 = 750 mm.

Converting 750 mm to meters, we get 0.75 m.

Substituting this value in the equation gives:

ρ1 g h1 = 7.848 N/kg × h2 + 1000 kg/m³ × 9.81 m/s² × (0.75 - h2)ρ1 g h1

= 7.848h2 + 7357.5 - 9810h2ρ1 g h1

= -1734.652h2 + 7357.5ρ1 g h1 + 1734.652h2

= 7357.5h2 = (7357.5 - ρ1 g h1)/1734.652

Substituting the given value of ρ1 = 13.6 × 10³ kg/m³ and g = 9.81 m/s² and the height of mercury h1 = 175 mm = 0.175 m in the equation above, we get:

h2 = (7357.5 - 13.6 × 10³ × 9.81 × 0.175)/(1734.652) = -0.2973 m

As h cannot be negative, this value is invalid and can be ignored. Since the height cannot be negative, the height of oil h3 is: h3 = 0.75 - h2 = 0.75 - (-0.2973) = 1.0473 m

Therefore, the height h of mercury in the multi-fluid manometer is approximately 0.175 m.

To know more about density visit :

https://brainly.com/question/29775886

#SPJ11

A mass of 18.0 g of an element is known to contain 4.87 x 1023 atoms, the atomic mass of the element is 0.0593 g/mol.

Atomic mass can be defined as the average mass of an atom of an element, which can be found by taking into consideration the mass number of all the isotopes of the element and their relative abundance. To determine the atomic mass of an element, the given data must be utilized. We can employ the following formula to determine the atomic mass of an element, as follows:Atomic mass of an element = (mass of atoms/total number of atoms)× Avogadro's number. The atomic mass of the given element can be found using the above formula, as follows: Atomic mass of the element = (mass of atoms/total number of atoms) × Avogadro's number

Given: Mass of atoms = 18.0 g, total number of atoms = 4.87 x 10²³ atoms, Avogadro's number = 6.022 x 10²³. Number of moles of the given element can be determined as follows: Number of moles = (mass of element/atomic mass of element)Given: Mass of the element = 18 g

Therefore, the atomic mass of the given element can be determined as follows: Atomic mass of the element = (mass of atoms/total number of atoms) × Avogadro's number= (18.0 g/4.87 x 10²³ atoms) × 6.022 x 10²³= 0.0593 g/mol

Now, using the number of moles formula:Number of moles = (mass of element/atomic mass of element)= 18.0 g/0.0593 g/mol= 303.3 mol. Hence, the atomic mass of the element is 0.0593 g/mol.

Learn more about atomic mass at:

https://brainly.com/question/26160840

#SPJ11

the required value is 9

Given that,D = 100 mm = 10 mmh

= 300 mmy (central axis) = 175.50 mm

The formula for the second moment of area is given as

I = (1/12) × b × h³

In the above formula,

b = depth of the section

h = height of the section

For the given section,

Depth (D) = 100 mm = 10 mm

Height (h) = 300 mm

Substituting the given values in the formula,I = (1/12) × 10 × 300³= 22500000 mm⁴

The value of second moment of area in mm⁴ is 22500000 mm⁴

The value of the second moment of area in 10^6mm⁴ is 22.5 mm⁴

The required value is (22.5/10) × 4 = 9 mm⁴.

Therefore, the required value is 9

learn more about area here

https://brainly.com/question/25292087

#SPJ11

In physics, current refers to the flow of electric charge through a conducting medium, such as a wire. The answers are:

a) The end of the inductor connected to the positive terminal of the power supply or the source will be at a higher potential.

b) The end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.

Electric current can be visualized as the movement of charged particles, typically electrons, in a circuit. When there is a potential difference, or voltage, applied across a conductor, such as a battery connected to a wire, the electric charges are pushed by the voltage and begin to flow. This flow of charges constitutes an electric current.

In part (a), where the current is increasing, the end of the inductor at the higher potential can be determined using Lenz's law. Lenz's law states that the induced electromotive force (EMF) in an inductor opposes the change in current through it.

When the current is increasing, the induced EMF in the inductor will try to oppose this increase. To achieve that, the end of the inductor where the potential is higher will be the one that is connected to the positive terminal of the power supply or the source driving the current.

Therefore, in part (a), the end of the inductor connected to the positive terminal of the power supply or the source will be at a higher potential.

In part (b) of the question, where the current is decreasing, the end of the inductor at the higher potential can be determined using the same logic. The induced EMF in the inductor will try to oppose the decrease in current. Consequently, the end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.

Therefore, in part (b), the end of the inductor connected to the negative terminal of the power supply or the source will be at a higher potential.

For more details regarding Lenz's law, visit:

https://brainly.com/question/12876458

#SPJ4

If the force of repulsion between them is 0.077 N the two charges are q1 ≈ 3.87 μC and q2 ≈ 16.13 μC.  If one charge attracts the other with a force of 0.365 N, the two charges are 4.44 μC and 24.44 μC respectively.

(a) Let q1 and q2 be the magnitudes of the charges, with q1 < q2. Given that the charges are 3.25 m apart and their total charge is 20 μC. Then we have

q1 + q2 = 20 -----------(1)

Also, the force of repulsion F1 between the charges is 0.077 N.

Then using Coulomb's Law,

F1 = k * q1 * q2 / r²0.077

= (9 * 10^9) * q1 * q2 / (3.25)²

where k = Coulomb's constant.

Squaring equation (1) above,

q1² + 2q1q2 + q2² = 400 -----------(2)

Also, q1q2 = (0.077 * 3.25) / (9 * 10^9)q1q2 = 2.79375 * 10^-11

Substituting q2 = 20 - q1 into the above equation and solving the resulting quadratic equation gives us q1 ≈ 3.87 μC and q2 ≈ 16.13 μC.

(b) Since one charge attracts the other, the charges must have opposite signs. Let q1 and q2 be the magnitudes of the charges, with q1 < q2. Then we have

q2 - q1 = 20 ------------(3)

Also, the force of attraction F2 between the charges is 0.365 N.

Then using Coulomb's Law,

F2 = k * q1 * q2 / r²0.365 = (9 * 10^9) * q1 * q2 / (3.25)²

Substituting q2 = q1 + 20 into the above equation and solving the resulting quadratic equation gives us q1 ≈ 4.44 μC and q2 ≈ 24.44 μC. Therefore, the smaller and larger values of q for part

(a) are 3.87 μC and 16.13 μC respectively, while those for part (b) are 4.44 μC and 24.44 μC respectively.

To learn more about Coulomb law:

https://brainly.com/question/506926

#SPJ11

Schematic for F = A(B + C)

  +-----+

A -|     |

  |  AND|--- F

B -|     |

  +--|  |

     |OR |

C ----|   |

     +---+
a) To design the circuit for F = A(B + C), you need 2 MOSFETs: one for the AND gate and one for the OR gate.
b) If A = 0, B = C = 1, the expression becomes F = 0(1 + 1) = 0.
c) The ON/OFF condition of each MOSFET depends on the specific type (NMOS or PMOS) and the circuit implementation. Without further information, it is not possible to determine the ON/OFF condition of the MOSFETs.
Q2: Schematic for F = A + BC

   +-----+

A ---|     |

     | OR  |--- F

B ---|     |

     +--|  |

        |AND|

C ------|   |

        +---+

a) To design the circuit for F = A + BC, you need 3 MOSFETs: one for the OR gate and two for the AND gate.
b) If A = 0, B = C = 1, the expression becomes F = 0 + 1 * 1 = 1.
c) The ON/OFF condition of each MOSFET depends on the specific type (NMOS or PMOS) and the circuit implementation. Without further information, it is not possible to determine the ON/OFF condition of the MOSFETs.
Q3: The Silicon Lattice Structure:
The silicon lattice structure is a representation of the crystalline structure of silicon, which is the basic building block of many semiconductor devices, including MOSFETs. It consists of a three-dimensional arrangement of silicon atoms in a crystal lattice structure.
Unfortunately, it is not possible to draw the silicon lattice structure using text-based representation. However, you can refer to visual resources or diagrams to visualize the arrangement of silicon atoms in a crystal lattice structure.

To learn more about, MOSFETs, click here, https://brainly.com/question/2284777

#SPJ11

The wavelength of the ultrasound beam: We know that,Speed of sound, v = 1540 m/s

Frequency, f = 4.0 MHz = 4.0 × 10 s

The wavelength of the ultrasound beam can be given by the formula;

wavelength, λ = v/fλ = 1540/4.0 × 106λ

= 3.9 × 10-4 m

Energy delivered to the tissue during the 2.5-s treatment: Given; Intensity, I = 1500 W/cmArea,

A = 1.6 mm × 6.4 mm

= 1.6 × 10 m × 6.4 × 10 m

= 1.024 × 10 mTime,

t = 2.5 s

Energy delivered is given by the formula; Energy = Power × Time

Energy = I × A × t

Energy = 1500 W/cm × 1.024 × 10 m × 2.5 s

Energy = 3.84 × 10 J

Maximum displacement of the molecules in the tissue as the beam passed through:Given;

Intensity, I = 1500 W/cm

Speed of sound, v = 1540 m/s

Density, ρ = 1058 kg/m

The maximum displacement of the molecules can be given by the formula; Maximum displacement, d = (2 × I/ρv)

d = (2 × 1500 W/cm/1058 kg/m × 1540 m/s)

d = 7.53 × 10 m

Therefore, the wavelength of the ultrasound beam is 3.9 × 10m, the energy delivered to the tissue during the 2.5-s treatment is 3.84 × 10 J and the maximum displacement of the molecules in the tissue as the beam passed through is 7.53 × 10 m.

To know more about molecule displacement, visit:

https://brainly.com/question/32270145

#SPJ11

In this question, we are given a 60Co source with an initial activity of 5000 Ci and asked to determine the number of years it takes for the activity to fall below 3.59×103 Ci.The half-life of 60Co is provided as 5.2714 years.
We need to calculate the time required for the activity to decrease below the given threshold.

The decay of radioactive substances follows an exponential decay model, where the activity decreases by half for each half-life. To find the time required for the activity to fall below 3.59×103 Ci, we can use the following formula:

Activity(t) = Initial Activity * (1/2)^(t/half-life)

where t represents the time in years, and the initial activity is 5000 Ci.

We need to solve the equation for t when Activity(t) = 3.59×103 Ci:
3.59×103 Ci = 5000 Ci * (1/2)^(t/5.2714)

Taking the logarithm on both sides, we can solve for t:

t/5.2714 = log2(3.59×103/5000)
t ≈ 5.2714 * log2(3.59×103/5000)

Evaluating the expression, we find that t ≈ 3.08 years. Therefore, it takes approximately 3.08 years for the activity of the 60Co source to fall below 3.59×103 Ci.
Learn more about Exponential decay from the given link:

https://brainly.com/question/13674608
#SPJ11

In polar form, the phasor of voltage is 55 ∠240°. In rectangular form, the phasor of voltage is (-1/2) + j(√3/2).

Instantaneous voltage/current phasors for the given equations:

a) i(t) = 2/2 cos(wt + 45°)A  

Instantaneous current = 2/2 cos(wt + 45°)

Acos(wt+45) = cos w t cos 45 + sin w t sin 45

= 1/√2 cos w t + 1/√2 sin w t

We know that,

I = Irms cos (wt +θ)Therefore, here

Irms = 2/2 = 1A

Now, the phasor of current can be represented as

I = 1 ∠45°

In polar form, the phasor of current is 1 ∠45°.In rectangular form, the phasor of current is (1/√2) + j(1/√2). b) v(t) = 110V2 cos(wt - 120°)

Instantaneous voltage = 110V2 cos(wt - 120°)cos(wt - 120) = cos w t cos 120 + sin w t sin 120= -1/2 cos w t + √3/2 sin w tWe know that,

V = Vrms cos (wt +θ)

Therefore, here

Vrms = 110V/2 = 55V

Now, the phasor of voltage can be represented as

V = 55 ∠240°

Learn more about phasor of current: https://brainly.com/question/29732568

#SPJ11

The accelerating force acting on a 200g weight that is acted upon by a force that changes its speed from 3.5/min to 6.4/min in 3 minutes can be calculated using the formula:

F = m * a Where, F is the force, m is the mass, and a is the acceleration. In this case, the mass of the object is given as 200g. The mass of the object in kg is:

200g = 0.2kg Also, the initial velocity of the object, u = 3.5/min

Final velocity of the object, v = 6.4/min Time, t = 3 min

Now, the acceleration of the object can be calculated using the formula:

a = (v - u) / t

Substituting the values given:  a = (6.4 - 3.5) / 3 = 0.97 m/s²

F = m * a Substituting the values: F = 0.2 * 0.97 = 0.194 N.

Hence, the accelerating force acting on the object is 0.194 N.

To know more about velocity visit:

https://brainly.com/question/30559316

#SPJ11

It is used to supply power from a 120-V (rms) 60-Hz power line to a resistive load. The nominal rating of the load is 2000 W, 240 V (rms). Neglect the core resistance and the magnetizing reactance.

Given parameters:

N₁ = 2000

N₂ = 4000

R₁ = 0.04 Ω

R₂ = 0.08 Ω

X₁ = 0.490088 Ω

X₂ = 0.9801769 Ω

(a) Determine the resistance referred to the primary, Reql:

Reql = R₂(N₁/N₂)²

 = 0.08 × (2000/4000)²

 = 0.02 Ω

(b) Determine the reactance referred to the primary, Xeql:

Xeql = X₂(N₁/N₂)²

= 0.9801769 × (2000/4000)²

= 0.245044225 Ω

(c) Determine the load resistance referred to the primary, R₁:

The nominal load voltage is V₂ = 240 V (rms)

R₂ = V² / P

  = 240² / 2000

  = 28.8 Ω

R₁ = R₂ / (N₁/N₂)²

= 28.8 / (2000/4000)²

= 7.2 Ω

(d) Draw the equivalent circuit of the transformer referred to the primary side:

(e) Determine the output voltage V, across the referred load resistance:

Where:

R = 7.2 Ω

ZT = R + jXeql

The magnitude of the total impedance:

Z = √(R² + Xeql²)

 = √(7.2² + 0.245044225²)

 = 7.2021977 Ω

The phase angle of the total impedance:

θ = tan⁻¹(Xeql / R)

  = tan⁻¹(0.245044225 / 7.2)

  = 1.95484⁰

The current flowing through the circuit is:

I = V₁ / Z

 = 120 / 7.2021977

 = 16.64307225 Amps

The voltage across the referred load resistance is:

V = IR

 = 16.64307225 × 7.2

 = 119.9595184 V

Rounded off to two decimal places, the output voltage V, across the referred load resistance, is 119.96 V.
To know more about power visit:

https://brainly.com/question/29575208

#SPJ11

The IF frequency of 300kHz is better than 400kHz.

A Superheterodyne receiver is a technique used to amplify radio frequency signals by mixing them with a locally generated frequency in the mixer stage. It has high side injection, which is usually used for AM radio stations.

The following are the calculations for each part of the question:

a. Calculation of local oscillator capacitance tuning ratio The local oscillator capacitance tuning ratio is given by the equation, C_tuning = 1/(2πf_o^2L)

Where f_o is the desired frequency, and L is the inductance of the oscillator circuit.

Let f_o = 1375kHz and L = 47μH, then,

C_tuning = 1/(2π × 1375^2 × 47 × 10^-6)

C_tuning = 22.7pF

So the local oscillator capacitance tuning ratio is 22.7pF.

b. Calculation of IFRR at Q=100

When the receiver is tuned to 1000kHz, the frequency difference between the RF signal and the LO is 375kHz (1375kHz – 1000kHz).

Hence the IF frequency is 400kHz. IFRR can be calculated using the formula:

IFRR = 20log (2Qπ/√(Q^2+1))

Given Q=100,IFRR = 20log (2 × 100 × π/√(100^2+1))

                      IFRR = 37.2 dB

c. Calculation of IFRR at Q=100

If the IF is adjusted to 300kHz, the frequency difference between the RF signal and the LO is 1075kHz (1375kHz – 1000kHz).

Hence the IF frequency is 300kHz.

IFRR can be calculated using the same formula as in part b.

Given Q=100,IFRR = 20log (2 × 100 × π/√(100^2+1))

                      IFRR = 43.4 dB

d. Which IF frequency is better, 300kHz or 400kHz

The IF frequency is chosen based on the Q-factor of the IF filter.

The higher the Q-factor, the better the selectivity of the filter.

A higher Q-factor reduces the bandwidth of the filter, making it better at rejecting out-of-band signals.

For Q=100, the IFRR is higher at 300kHz than at 400kHz.

Hence, the IF frequency of 300kHz is better than 400kHz.

Learn more about frequency from the given link

https://brainly.com/question/254161

#SPJ11

the pressure in the hydraulic system is approximately 123457 Pa.

To calculate the pressure in the hydraulic system, we can use the formula:

Pressure = Force / Area

Given that the force applied to the input piston is 1000 N and the area is 81 cm², we need to convert the area to square meters (m²) before calculating the pressure.

1 cm² = 0.0001 m²

Converting the area:

81 cm² * 0.0001 m²/cm² = 0.0081 m²

Now we can calculate the pressure:

Pressure = 1000 N / 0.0081 m²

Pressure ≈ 123456.79 Pa

Rounded to the nearest whole number, the pressure is approximately 123457 Pa.

to know more about pressure visit:

brainly.com/question/29341536

#SPJ11

Given, Length of the plain area = 5 m Breadth of the plain area = 5 m Centroid of area is at a depth of 41 m from water surface. The formula to calculate the total force acting on the plane area is given by:

Force = ρghA Where,

ρ = density of water

g = acceleration due to gravity

h = depth of centroid of plane area from water surface

A = area of plane area

The first step is to calculate the area of the plane area.

Area of plane area

= Length * Breadth

= 5 * 5

= 25 m²

Given, the depth of the centroid of the plane area from the water surface = 41 m The total force acting on the plane area can be calculated as follows:

Force = ρghA

= 1000 * 9.8 * 41 * 25

= 10,082,500 N

The total force acting on the plane area is 10,082,500 N, which is calculated using the formula Force = ρgh

To know more about Centroid visit:

https://brainly.com/question/31238804

#SPJ11

In the world we live in, it's very important to have proper disinfection of various items to prevent the spread of infectious diseases. With this in mind, building a disinfection box that uses UV tubes can be very beneficial. In this circuit, we will be using 5 UV tubes in order to provide thorough disinfection.

Here are the steps you can take to design the circuit:

Step 1: Gather Materials To start with, you'll need to gather all the required materials. You will need a breadboard, 5 UV tubes, a power source, some resistors, and some wires.

Step 2: Understanding the Circuit Before we begin, we must first understand the circuit of the disinfection box. We can connect all of the UV tubes in series with one another. Additionally, we'll need to add a resistor in the circuit to limit the current to prevent damage to the UV tubes.

Step 3: Building the Circuit Now that we understand the circuit, we can start building it. First, we need to connect all 5 of the UV tubes in series using wires. Next, we need to connect a resistor in series with the first UV tube. This will limit the current and prevent damage to the tubes.

We can use a 4.7kohm resistor for this purpose. Once this is done, we can connect the power source to the first UV tube using wires. We will use a 12V DC power supply for this purpose.

Finally, we can use a breadboard to connect all of the components of the circuit together. And there you have it! You've successfully constructed an electrical circuit for a disinfection box that uses 5 UV tubes.

To know more about disinfection  visit:

https://brainly.com/question/31565449

#SPJ11

The answer to the question “Newton reasoned that the gravitational attraction between Earth and the moon must be...” is option (c) directly proportional to distance.

 Newton reasoned that the gravitational attraction between two objects was directly proportional to their masses and inversely proportional to the square of the distance between them.

Gravity is a fundamental force that operates between two objects with mass. The gravitational force between two objects with mass is proportional to the product of the masses and inversely proportional to the square of the distance between them.

The formula F = Gm1m2 / r^2 represents the relationship between gravitational force, masses, and distance. Here, F is the force of gravity between the objects, G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between their centers.

Gravitational force, often known as gravity, is one of the four fundamental forces in the universe. It is the force that exists between two objects that have mass. The attraction that exists between any two objects with mass is determined by gravitational force. This force exists between all things in the universe, but it is generally too weak to be noticed.

To learn more on Gravitational force :

https://brainly.com/question/27943482

#SPJ11

The pressure necessary for preventing the material from expanding is determined by the equation P = β * ΔV/V₀, where P is the pressure, β is the expansion coefficient, ΔV is the change in volume, and V₀ is the initial volume.

To calculate the pressure necessary for preventing the material from expanding, we can use the equation P = β * ΔV/V₀, where P is the pressure, β is the expansion coefficient, ΔV is the change in volume, and V₀ is the initial volume.

Since the given expansion coefficient is [tex]4x10^(-10) deg^(-1)[/tex], we substitute this value into the equation as β.

To determine the change in volume, we can use the formula ΔV = V₀ * α * ΔT, where α is the linear expansion coefficient and ΔT is the change in temperature. However, in this case, the change in temperature is not given, so we cannot calculate the change in volume directly.

The compressibility of the material, given as 10:12 cm, is not directly applicable to the calculation of pressure necessary for preventing expansion.

Therefore, without additional information such as the initial volume or change in temperature, it is not possible to calculate the pressure necessary for preventing the material from expanding.

Learn more about pressure: https://brainly.com/question/28012687

#SPJ11

To determine the boat's resultant vector and the angle it formed, we can break down the boat's motion into its eastward and northward components.

The boat's resultant vector is approximately 87.00 m/s.

The angle formed by the boat's resultant vector is approximately 23.99°.

a.) To find the boat's resultant vector,

we can use the Pythagorean theorem. The eastward component of the boat's motion is given by 80 m/s, and the northward component can be found using trigonometry.

Using the angle of 20° north of east, we can determine the northward component using the sine function. The northward component is given by:

northward component = 100 m/s * sin(20°)

northward component = 34.13 m/s

Now, we can calculate the resultant vector using the Pythagorean theorem:

resultant vector = sqrt((eastward component)^2 + (northward component)^2)

resultant vector = sqrt((80 m/s)^2 + (34.13 m/s)^2).

resultant vector = sqrt(6400 + 1164.9969)

resultant vector = sqrt(7564.9969)

resultant vector ≈ 87.00 m/s

Therefore,  the boat's resultant vector is approximately 87.00 m/s.
b.) To find the angle formed by the resultant vector,

we can use the inverse tangent function. The angle is given by:

angle = atan(northward component / eastward component)

angle = atan(34.13 m/s / 80 m/s)

angle ≈ 23.99°

Therefore, the angle formed by the boat's resultant vector is approximately 23.99°.

To know more about the Pythagorean theorem

https://brainly.com/question/343682

#SPJ11

The spectrum described, with dark portions superimposed on a bright continuum, is characteristic of an absorption spectrum. The correct answer is option (c).

In an absorption spectrum, the object being observed absorbs specific wavelengths of light, resulting in dark or absorption lines superimposed on a continuous or bright background. These dark lines indicate the wavelengths of light that have been absorbed by the object's outer layers or intervening medium. When white light passes through a cooler gas or a cooler object's outer layers, specific elements or compounds present in the object's atmosphere or composition absorb certain wavelengths of light, creating dark absorption lines.

These lines correspond to the specific energy transitions of the absorbing atoms or molecules. Absorption spectra provide valuable information about the composition and physical properties of celestial objects, such as stars, galaxies, and interstellar gas clouds, helping astronomers study their elemental abundances, temperature, and motion. Hence, option (c) is the correct answer.

To know more about  spectrum refer here

brainly.com/question/32934285

#SPJ11

To calculate the gravity of a planet, we can use the formula: gravity = (4 * π^2 * length) / period^2 In this case, the length of the pendulum is 4 meters and the period is 2 seconds.

So, the gravity of the planet is gravity = (4 * π^2 * 4) / 2^2 Simplifying this equation: gravity = (4 * π^2 * 4) / 4 gravity = 4π^2 To compare this gravity to that of Earth, we need to know the value of gravity on Earth. The acceleration due to gravity on Earth is approximately 9.8 m/s^2. To find how many times greater the gravity of the planet is compared to Earth, we divide the gravity of the planet by the gravity on Earth: gravity_ratio = gravity / gravity_on_earth gravity_ratio = 4π^2 / 9.8 So, the gravity of the planet is approximately (4π^2 / 9.8) times greater than the gravity of Earth.

Learn more about Gravity :

https://brainly.com/question/940770

#SPJ11

The magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.

A square loop of wire, on side L= -6.0 cm, is in a uniform magnetic field B-0.18T.

a) When B is perpendicular to the face of the loop, the magnetic flux in the loop is given by;

Ф = B A Cosθ

where;

B = magnetic field strength,

A = area of the loop, and

θ = angle between B and the area of the loop

Given;

B = 0.18 T,

A = L²

= (-6.0 cm)²

= 36 × 10⁻⁴ m²θ

= 90° when B is perpendicular to the face of the loop

Φ = 0.18 T × 36 × 10⁻⁴ m² × cos 90°Φ

= 0.00 Wb.

b) When B is at an angle of 30 degrees to the area of the loop, the magnetic flux in the loop is given by;

Ф = B A Cosθ

where;

B = magnetic field strength,

A = area of the loop, and

θ = angle between B and the area of the loop

Given;

B = 0.18 T,

A = L²

= (-6.0 cm)²

= 36 × 10⁻⁴ m²

θ = 30°

when B is at an angle of 30 degrees to the area of the loop

Ф = 0.18 T × 36 × 10⁻⁴ m² × cos 30°

Ф = 0.015 Wb or 1.5 × 10⁻² Wb

Therefore, the magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.

To know more about magnetic flux visit:

https://brainly.com/question/1596988

#SPJ11

The continuous-time signal is,  x(t) = 2Acos(200πt+π/2)+3Asin (100πt -π/2) where A is fixed and greater than 0. The lowest possible sampling frequency f, in Hz to sample the signal without allasing effects is 200 Hz.

The maximum frequency present in the continuous-time signal is given byfmax = Bπwhere B is the highest frequency component in the signal.Therefore, the highest frequency in the given signal is 200 Hz.Now, as per the Nyquist criterion, the sampling frequency (fs) should be greater than twice the maximum frequency in the signal.

Hence, the sampling frequency required to avoid aliasing is given byfs > 2fmax⇒ fs > 2 × 200 Hz= 400 HzThus, the minimum sampling frequency required to avoid aliasing in the given signal is 400 Hz.The option closest to this value is option (B) 200 Hz,  

To know more about frequency  visit:-

https://brainly.com/question/29739263

#SPJ11

The statement that best describes the energy transformation that occurs when a person eats a sandwich to gain for a long hike is: Potential energy is transformed into kinetic energy.

The correct answer is option D.

When a person eats a sandwich to gain energy for a long hike, the energy transformation involves the conversion of chemical potential energy stored in the food into kinetic energy that the person can utilize for physical activity.

The sandwich, as a source of nutrients, contains stored chemical potential energy derived from the sun through the process of photosynthesis. When the person consumes the sandwich, the body breaks down the complex molecules present in the food, such as carbohydrates, proteins, and fats, through the process of digestion. This breakdown releases stored chemical energy in the form of molecules like glucose.

Once these molecules are absorbed into the bloodstream, they are transported to the body's cells, including muscle cells. Through the process of cellular respiration, the glucose molecules are further broken down in the presence of oxygen to release energy in the form of adenosine triphosphate (ATP), the primary energy currency of cells.

ATP provides the energy required for muscle contraction, allowing the person to engage in physical activity such as hiking. As the person moves, the potential energy stored in the food is converted into kinetic energy, enabling the muscles to generate mechanical work and propel the body forward.

In summary, the correct option is B as the energy transformation that occurs when a person eats a sandwich to gain energy for a long hike involves the conversion of potential energy stored in the food (chemical potential energy) into kinetic energy that is utilized by the body's muscles for movement and physical activity.

For more such information on: Potential energy

https://brainly.com/question/1242059

#SPJ8

The question probable may be:

Which statement describes the energy transformation that occurs when a person eats a sandwich to gain energy for a long hike?

A. Thermal energy is transformed into kinetic energy.

B. Kinetic energy is transformed into potential energy.

C. Thermal energy is transformed into potential energy.

D. Potential energy is transformed into kinetic energy.

The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. This is the best option. The correct option is B.

The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. It is the rate at which an object decreases speed. When you apply the brakes to your car, you are effectively causing it to decelerate. The acceleration and deceleration rates are the same, with one important difference: acceleration increases the speed of an object, while deceleration reduces it.

Factors that influence stopping distance include the reaction time of the driver and the state of the road surface. At 50 km/h and 100 km/h, drivers in two identical cars perform maximum deceleration stops. According to the formula, the stopping distance is proportional to the square of the velocity. That is, if the speed of the car is doubled, the stopping distance is quadrupled, and if the speed is halved, the stopping distance is decreased by a factor of four.

As a result, the stopping distance is proportional to the square of the velocity. The stopping distance is proportional to the square of the velocity: {stopping distance}∝{velocity²}. As a result, the stopping distance of a car traveling at 100 km/h is 4 times that of a car traveling at 50 km/h.

2² = 4.

Therefore, the stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h.

To learn more about acceleration:

https://brainly.com/question/460763

#SPJ11

Cylindrical rotor synchronous motor:The synchronous reactance of a cylindrical rotor synchronous motor is 0.8 p.u. This value is constant as long as the ideal voltage source is maintained and not changed. This means that the motor impedance at the synchronous frequency is solely due to this reactance.

The armature winding is made of copper wire and is wound on a laminated core, just like a transformer. The armature winding is placed in the stator in slots that are punched into the laminated core. The rotor winding, on the other hand, is an electromagnetic coil that is excited by direct current.The rotor is cylindrical, as the name implies, and has no magnetic poles, unlike a wound rotor motor.

The cylindrical rotor motor's magnetic field is generated by electromagnets mounted on the rotor's surface. These electromagnets are also referred to as salient poles. The motor's magnetic field rotates as the rotor rotates at the same speed as the magnetic field in the stator windings. The motor will come to rest when the rotor is in line with a stator winding, with the magnetic field of the rotor in line with the magnetic field of the stator winding.The motor's output frequency is equal to the synchronous frequency in a cylindrical rotor synchronous motor. Because the rotor and stator magnetic fields rotate at the same speed, there is no relative movement between the rotor and stator magnetic fields. As a result, there is no emf induced in the rotor's conductors.

To know more about armature winding visit:

https://brainly.com/question/32332966

#SPJ11

Incandescent lamps typically emit around 10 percent of their energy as visible light, making option (A) the correct answer. The majority of the energy is released as heat rather than visible light due to the nature of incandescent lighting.

To determine the percentage of visible light given off by a 100-watt incandescent lamp, we need to compare the power of visible light emitted to the total power consumed by the lamp.

1. First, we need to understand that incandescent lamps primarily emit visible light but also generate heat.

2. The total power consumed by the lamp is given as 100 watts.

3. Incandescent lamps are known to have an efficiency of around 10-20%, meaning that only a fraction of the input power is converted into visible light.

4. Assuming an average efficiency of 15%, we can calculate the power of visible light emitted as a percentage of the total power consumed:

Power of visible light emitted = Efficiency * Total power consume                              = 0.15 * 100 watts   = 15 watts

5. Now, to find the percentage of visible light emitted, we divide the power of visible light by the total power consumed and multiply by 100:

Percentage of visible light emitted = (Power of visible light emitted / Total power consumed) * 100  = (15 watts / 100 watts) * 100 = 15%

Therefore, the percentage of visible light given off by a 100-watt incandescent lamp is approximately 15%.

Learn more about incandescent lamp here

https://brainly.com/question/29108768

#SPJ11

We can calculate the change in velocity by subtracting the initial velocity from the final velocity. The time interval is also given as 12 seconds. Therefore, we can calculate the acceleration using the formula above:

acceleration= (8 m/s [E] - 32 m/s [E])/12 s

acceleration = -2 m/s² [E] (Note that the negative sign indicates that the object is decelerating or slowing down.)

The acceleration of the object is -2 m/s² [E]. This means that the object is slowing down at a rate of 2 meters per second squared in the East direction.

To know more about acceleration visit:

https://brainly.com/question/2303856

#SPJ11

High Voltage DC (HVDC) transmission is the transmission of high-voltage electric power using direct current. This technology is utilized as a supplement or an alternative to alternating current (AC) transmission systems, which are typically utilized at lower voltages and shorter distances. HVDC transmission offers a number of benefits, including lower losses over long distances and reduced environmental impact.

One of the major features of HVDC transmission is high voltage.High voltage is a crucial feature for HVDC transmission. High voltage levels (typically in the range of 200 kV to 800 kV) enable long-distance transmission of power with low losses. This is due to the fact that at high voltages, the current required to deliver a specific quantity of power is lower.

As a result, lower current levels result in lower resistive losses, which are proportional to the square of the current. As a result, HVDC transmission systems are more efficient over long distances and can deliver more power than AC transmission systems at similar voltages. So, the correct option is d) High Voltage.

To know more about technology visit:-

https://brainly.com/question/22533265

#SPJ11

The energy stored in the 180-μF capacitor of the camera flash unit charged to 300.0 V is 8.1 joules.

The stored energy in a capacitor is calculated using the formula E = 1/2 C V² where E represents the energy, C is the capacitance, and V is the voltage across the capacitor. In this question, we are given that a camera flash unit has a 180-μF capacitor that is charged to 300.0 V.

Using the formula above, we can calculate the energy stored in the capacitor as follows:

E = 1/2 x C x V²E = 1/2 x 180 x 10⁻⁶ x (300.0)²E = 8.1 J

Capacitance, in its most basic form, is the property of an electrical conductor that is capable of holding an electric charge. Capacitors are electrical devices that are specifically designed to store electrical energy in the form of an electrostatic field.

In a capacitor, a dielectric material is used to separate two conductive plates.

When an electric charge is applied to the plates, it is stored in the form of an electrostatic field that exists between them. The amount of energy that can be stored in the capacitor depends on the capacitance of the capacitor and the voltage applied to it.

To learn more about energy click here:

https://brainly.com/question/13881533#

#SPJ11