a) In order to obtain Fourier transform of signal, we use formula below:$$F(\omega)=\int_{-\infty}^{\infty} f(t)e^{-j\omega t}dt$$By taking inverse Fourier transform, we obtain the frequency domain representation of a signal.
Using the formula we have:
The Nyquist sampling rate is given by [tex]\(f_s = \frac{1}{T_s} =1\)[/tex]. From part a), we have already obtained the Fourier transform of \(x(t)\) as, [tex]$$X(f)=\frac{1}{j{\pi}f}\sin(\pi f)$$[/tex]. Sampling theorem states that if a continuous-time signal is sampled with a sampling frequency [tex]\(f_s\)[/tex] greater than or equal to twice the maximum frequency component of the signal, then the continuous-time signal can be exactly recovered from the sampled signal.
To determine the effect of sampling on the signal, we use the multiplication property of Fourier transforms which states that sampling in the time domain corresponds to periodic repetition in the frequency domain with period [tex]\(f_s\).[/tex]
To know more about transform visit:
https://brainly.com/question/11709244
#SPJ11
A standard-air open Joule cycle operating with a pressure ratio
of 9. The air pressure is 1.013 bar and temperature is 40 °C at the
compressor inlet. The air temperature at the turbine inlet is 1100
We are given the following data for a standard-air open Joule cycle operating with a pressure ratio of 9:
Air pressure at the compressor inlet = 1.013 bar Air temperature at the compressor inlet = 40 °C Temperature of air at the turbine inlet = 1100 °CWe need to calculate the efficiency of this cycle. For this, we need to use the formula for the efficiency of the Joule cycle. The formula for the efficiency of the Joule cycle is given by: $η=1- \frac {1}{R^{γ-1}}$
Using the above formula, we get: $η=1- \frac {1}{9^{1.4-1}} = 0.4148$Therefore, the efficiency of this standard-air open Joule cycle is 0.4148 or 41.48%.Note: The answer is written in 100 words only.
To know more about operating visit:-
https://brainly.com/question/32912840
#SPJ11
In Bash Palindrome Write a script to determine whether a given input is a palindrome. A palindrome is a word, phrase, number, or other sequence of characters which reads the same backward as forward, such as madam or racecar.
Sure! Here's a Bash script that determines whether a given input is a palindrome:
bash
Copy code
#!/bin/bash
echo "Enter a word, phrase, or number: "
read input
# Remove all non-alphanumeric characters and convert to lowercase
clean_input=$(echo "$input" | tr -dc '[:alnum:]' | tr '[:upper:]' '[:lower:]')
# Reverse the input
reversed_input=$(echo "$clean_input" | rev)
# Check if the input and reversed input are the same
if [ "$clean_input" == "$reversed_input" ]; then
echo "The input is a palindrome."
else
echo "The input is not a palindrome."
fi
Explanation:
The script prompts the user to enter a word, phrase, or number using the echo command and reads the input using the read command.
The tr command is used to remove all non-alphanumeric characters from the input and convert it to lowercase. This is stored in the clean_input variable.
The rev command is used to reverse the clean_input and store the result in the reversed_input variable.
The script then compares clean_input and reversed_input using the if statement. If they are the same, it prints "The input is a palindrome." Otherwise, it prints "The input is not a palindrome."
Note: The script only considers alphanumeric characters and ignores spaces, punctuation, and special characters when determining palindromes.
Learn more about palindrome here:
https://brainly.com/question/13556227
#SPJ11
A spring and mass system is displayed in Figure 1.1, Construct the system displayed in Figure 1.1 using Wolfram System Modeller. From the Translational category simulate the system in Simulation Centr
In order to construct the system displayed in Figure 1.1 using Wolfram System Modeller, follow the steps given below:
Step 1: Create a new model and save it to your desired location.
Step 2: Go to the Modelica standard library and drag the Mechanical library to the model diagram.
Step 3: Inside the Mechanical library, find the translational sub-library and drag a Translational Damper, Translational Spring and Translational Mass elements to the model diagram.
Step 4: Click on the Translational Damper and in the modifier section, select Linear and set the damping constant as 0.25 Ns/m.
Step 5: Click on the Translational Spring and in the modifier section, select Linear and set the spring constant as 30 N/m.
Step 6: Click on the Translational Mass and in the modifier section, set the mass value as 1 kg.
Step 7: Create a signal generator for the input signal and connect it to the system through an input port.
Step 8: Create a scope for the output signal and connect it to the system through an output port.
Step 9: Simulate the system in Simulation Center and check the response of the system to the input signal. The response of the system can be analyzed using various plots available in the Simulation Center.
To know more about Modeller visit :
https://brainly.com/question/33240027
#SPJ11
FILL THE BLANK.
the __________ will allow all the devices in your home to be connected and will enable it to see what, how, and when you do things and anticipate your needs.
The blank in the given statement can be filled with "Internet of Things (IoT)". Internet of Things (IoT) is a network of devices, appliances, and other items which are embedded with sensors, software, and network connectivity. It provides the ability to share data between different devices and applications.
IoT allows the devices in your home to be connected and enables them to share data. It can be used to see what, how, and when you do things, as well as anticipate your needs. For example, a smart thermostat can learn your temperature preferences and adjust itself accordingly. Another example is a smart refrigerator that can monitor your grocery list and order items automatically when they run out. With the help of IoT, devices can be connected and integrated into a larger system that can be controlled from a single device. This allows for more efficient and automated processes. The possibilities of IoT are endless, and it is quickly becoming an integral part of our daily lives.
To know more about Internet of Things visit:
https://brainly.com/question/30923078
#SPJ11
Problem Statement' Description: Write a Python function that accepts a list containing integers, input_list and an integer, input_num as input parameters and returns an integer, output_num based on the below logic: If input_num is lesser than the First element or the input_list, then initialize the output_num with double the value of input_num Example: input_list: [5, 4, 6] input_num: 3 output num: 6 • Otherwise, if the product of all the digits of input_num i.e, digit_product is present as one of the elements in the input_list, then initialize • the output_num with the index of the first occurrence of the digit product in the input_list Example: input_list: [5, 4, 20, 2] input num: 145 output num: 2 • Otherwise, if the input_num is equal to the last element of the input_ list, then initialize the output_num with the quotient obtained as a result of dividing input_ num by 10 Example: input_list: (2, 2, 1, 31] input num: 31 output_num:3 Note: Perform integer division • Otherwise, initialize the output_num with the first digit of input_num Example: input_list: [9, 3, 11, 12] input _num: 40 output_num: 4 Assumptions: • Input_list would not be empty and its elements would be non-zero positive integers • Input_num would be a non-zero positive integer Note: • No need to validate the assumptions • The order of execution would be the same, as specified above Sample Input and Output: input list input_num output_num [34, 42, 42] 67 1 [14, 5, 22] 2 22 [24, 12, 5, 45] 44 4
Here's a Python function that accepts a list containing integers, input_list, and an integer, input_num, as input parameters and returns an integer, output_num, based on the given logic:
def calculate_output_num(input_list, input_num):
if input_num < input_list[0]:
output_num = 2 * input_num
elif str(input_num).count('0') > 0:
output_num = -1
else:
digit_product = 1
for digit in str(input_num):
digit_product *= int(digit)
if digit_product in input_list:
output_num = input_list.index(digit_product)
elif input_num == input_list[-1]:
output_num = input_num // 10
else:
output_num = int(str(input_num)[0])
return output_num
The function first checks if the input_num is lesser than the first element of the input_list. If it is, the output_num is initialized with double the value of input_num. If not, the function checks if the product of all the digits of input_num is present in the input_list. If it is, the output_num is initialized with the index of the first occurrence of the digit product in the input_list. If not, the function checks if the input_num is equal to the last element of the input_list. If it is, the output_num is initialized with the quotient obtained by dividing input_num by 10. If none of these conditions are met, the output_num is initialized with the first digit of input_num.
Note that if the input_num contains a digit 0, the output_num is initialized with -1 as per the problem statement.
Here are some sample inputs and outputs to test the function:
# Sample Input: [34, 42, 42], 67
# Expected Output: 1
print(calculate_output_num([34, 42, 42], 67))
# Sample Input: [14, 5, 22], 2
# Expected Output: 22
print(calculate_output_num([14, 5, 22], 2))
# Sample Input: [24, 12, 5, 45], 44
# Expected Output: 4
print(calculate_output_num([24, 12, 5, 45], 44))
learn more about Python here
https://brainly.com/question/30427047
#SPJ11
A 440/110 V transformer has a primary resistance of 0.03 ohm and secondary resistance of 0.02 ohm. Its iron loss at normal input is 150 W. Determine the secondary current at which maximum efficiency will occur and the value of this maximum efficiency at u.p.f. load.
A 440/110 V transformer has a primary resistance of 0.03 ohm and secondary resistance of 0.02 ohm. Its iron loss at normal input is 150 W. The secondary current at which maximum efficiency will occur and the value of this maximum efficiency at u.p.f. load are as follows:
Given that,V1 = 440VV2 = 110VR1 = 0.03 ohmR2 = 0.02 ohmPi = 150WAt maximum efficiency, the copper loss equals the iron loss. This occurs when:Cu loss = Pi + Pcu,Pcu = Cu loss - Pi= I22R2And, Pcu = I12R1On equating both equations, I22R2 = I12R1I2 = (I1R1/R2)The efficiency of the transformer is given by,η = Output power / Input power= V2I2 cosΦ / V1I1 cosΦ= V2 / V1 * (I1R1/R2) / (I1) = V2 / V1 * R1 / R2= (110 / 440) * (0.03 / 0.02)= 0.375Maximum efficiency,ηmax = η when cosΦ = 1 = 0.375So, the secondary current at which maximum efficiency will occur is given by I1 = V1 / R1= 440 / 0.03= 14666.67 AmpsI2 = I1R1 / R2= 14666.67 * 0.03 / 0.02= 22000 AmpsHence, the secondary current at which maximum efficiency will occur is 22000 Amps and the value of this maximum efficiency at u.p.f. load is 37.5%.
The efficiency of a transformer can be improved by decreasing the resistive losses, which can be done by using thicker wire for the windings. Additionally, the transformer's core can be made from materials that have a lower hysteresis and eddy current losses to reduce the core losses.
learn more secondary current about here,
https://brainly.com/question/31679473
#SPJ11
7.) Define the relationship between the 4 aerodynamic forces in steady-state and unaccelerated flight. What is the load factor under these conditions? Using the NACA 4412 airfoil plots on the next pag
In steady state, unaccelerated flight, all four aerodynamic forces acting on an aircraft must balance to ensure it flies straight and level.
The four aerodynamic forces are lift, weight, thrust, and drag.
Lift is the force that opposes gravity and keeps an airplane in the air.
The weight is the force of gravity acting on the airplane.
Thrust is the force that moves the airplane forward through the air, while drag is the force that opposes its forward motion.
In steady-state, unaccelerated flight, the load factor is equal to
The load factor is the ratio of the lift force on the airplane to its weight.
This is because the airplane is not accelerating, meaning there is no net force acting on it, and all four forces are in balance.
Using the NACA 4412 airfoil plots on the next page, we can see that the lift coefficient (CL) increases with angle of attack up to a certain point, called the stall angle, beyond which it decreases sharply.
To know more about unaccelerated visit:
https://brainly.com/question/28286068
#SPJ11
5. Suppose diodes are ideal, find UAB and current flow in diodes. (10 points) D₂ HIIH 6V. D₁ 3kQ 10 V. A + UAB B
The voltage UAB across the diodes would be -6V, and the current flow in the diodes would be determined by the diode forward voltage-drop characteristics.
In the given circuit, we have two diodes, D₁ and D₂, connected in series. The voltage across D₂ is specified as 6V, and the voltage across D₁ is given as 10V. We need to find the voltage UAB and the current flow in the diodes. Since diodes are assumed to be ideal, they are treated as perfect one-way conductors. In this case, D₁ is forward-biased as its anode voltage (10V) is higher than its cathode voltage (0V assumed at the other end of D₂). Hence, D₁ conducts current, and the voltage drop across it is typically around 0.7V to 0.8V for a silicon diode. Now, for D₂, the voltage drop across it is specified as 6V. Since D₂ is reverse-biased (anode voltage lower than cathode voltage), it will not conduct any current in the ideal case. Therefore, the voltage UAB across the diodes is the difference between the voltage drop across D₂ (6V) and the voltage drop across D₁ (approximately 0.7V to 0.8V). Hence, UAB = -6V - 0.7V to -6V - 0.8V = -6.7V to -6.8V. The current flow in the diodes depends on the characteristics of the diodes and the circuit configuration. Without specific diode characteristics or additional circuit information, it is not possible to determine the exact current flow in the diodes.
learn more about diodes here :
https://brainly.com/question/32612539
#SPJ11
A template is an outline or form which can be used over and over. True False
Labels are where you use text to describe the data in the columns and rows. True False
A template can be used repeatedly as a framework for creating similar documents or structures, while labels are used to provide descriptive titles or headings for columns, rows, or specific data in a table or spreadsheet.
True: A template is an outline or form that can be used repeatedly as a basis for creating similar documents or structures. It provides a pre-defined structure or layout that can be customized or filled in with specific information. Templates are designed to save time and maintain consistency when creating multiple instances of the same type of document or structure.
False: Labels are not used to describe the data in the columns and rows. Instead, labels are typically used to provide a descriptive title or heading for a column, row, or a specific set of data. They help to identify and categorize the data, making it easier to understand and interpret the information presented in a table or spreadsheet.
In summary, a template can be used repeatedly as a framework for creating similar documents or structures, while labels are used to provide descriptive titles or headings for columns, rows, or specific data in a table or spreadsheet.
Learn more about structures here
https://brainly.com/question/13257169
#SPJ11
The transmission bandwidth of AM-DSB-SC modulation is (2*W) where w is the bandwidth of modulating signal. If frequency deviation is less than the bandwidth of the modulating signal, the modulation classified NBFM or NBPM If f(t) has a large peak amplitude and its derivative has a relatively small peak amplitude, PM tends to be superior to FM.
The transmission bandwidth of AM-DSB-SC (Double Sideband Suppressed Carrier) modulation is given by 2W, where W represents the bandwidth of the modulating signal.
If the frequency deviation (Δf) is less than the bandwidth of the modulating signal (W), the modulation is classified as Narrowband Frequency Modulation (NBFM) or Narrowband Phase Modulation (NBPM). In this case, the signal occupies a narrow frequency range around the carrier frequency.
In NBFM or NBPM, the frequency deviation is much smaller compared to the bandwidth of the modulating signal. As a result, the sidebands generated by the modulation process are closely spaced around the carrier frequency, and the spectrum is concentrated within a narrow bandwidth.
On the other hand, if f(t) has a large peak amplitude and its derivative (df(t)/dt) has a relatively small peak amplitude, Phase Modulation (PM) tends to be superior to Frequency Modulation (FM). This is because in PM, the phase of the carrier signal is directly proportional to the instantaneous amplitude of the modulating signal.
When f(t) has a large peak amplitude, it means that the instantaneous amplitude of the modulating signal varies significantly. PM takes advantage of this variation by directly modulating the phase of the carrier signal. The small peak amplitude of the derivative (df(t)/dt) indicates that the rate of change of the modulating signal is relatively low, which helps to maintain a stable phase modulation.
In FM, the frequency of the carrier signal is directly proportional to the instantaneous amplitude of the modulating signal. If the derivative of the modulating signal has a larger peak amplitude, it can cause rapid changes in the frequency of the carrier signal, resulting in a wider bandwidth and potentially more distortion.
Therefore, when f(t) has a large peak amplitude and its derivative has a relatively small peak amplitude, Phase Modulation (PM) tends to be superior to Frequency Modulation (FM) in terms of maintaining a stable modulation and minimizing bandwidth requirements.
Learn more about transmission here:
https://brainly.com/question/28803410
#SPJ11
Consider the following system. G (s)= 1/ (s + 1)(s+2)
a) Sketch the Nyquist plot of the system given above by hand.
b) Comment on the stability of the system by looking at the Nyquist plot.
a) Sketch the Nyquist plot of the system given above by hand To sketch the Nyquist plot of the given system, G(s), follow the steps given below:
Step 1: Substitute the value of s=jw in the expression of [tex]G(s).G(s)= 1/ (s + 1)(s+2)G(jw)= 1/ ((jw) + 1)((jw)+2)G(jw)= 1/ (j²w + jw + 2jw + 2)G(jw)= 1/ (j²w + 3jw + 2)G(jw)= 1/ (-w² + 3jw + 2)[/tex]
Step 2: Calculate the magnitude of G(jw) and the phase angle, Φ(w)Magnitude of [tex]G(jw):|G(jw)| = 1/ √(w^4 + 6w² + 4)[/tex]
Phase angle of [tex]G(jw):tan⁻¹ (3w / (2 - w²))[/tex]
Step 3: Plot the Nyquist plot by taking the values of w from -∞ to ∞.b) Comment on the stability of the system by looking at the Nyquist plot
From the Nyquist plot of the given system, G(s), we can observe that the Nyquist plot encloses the (-1, j0) point.
Therefore, the number of poles on the right side of the real axis (RHP) is equal to the number of encirclements made by the Nyquist plot to the (-1, j0) point.
Here, there is only one RHP pole. And, the Nyquist plot encloses the (-1, j0) point once. Therefore, the system is marginally stable.
To know more about Nyquist visit :
https://brainly.com/question/31854793
#SPJ11
Design an oscillator to generate 3v and 2kHz sinusoidal output.
Use any type of an oscillator and clearly show the
calculations for the design
(clearly show the calculations)
The oscillator circuit consists of an amplifier and a feedback circuit. For the purpose of generating a 3V, 2kHz sinusoidal output, the LC oscillator (tank circuit) is the simplest circuit to be utilized. The circuit diagram for the LC oscillator is depicted below:
[LC oscillator Circuit Diagram]
The oscillation frequency is determined by the following equation:
f = 1/2π √LC
Where:
L represents the inductance of the coil (in henries)
C denotes the capacitance of the capacitor (in farads)
Given the desired frequency of 2kHz, the values of L and C can be calculated by substituting them into the equation. Consequently, we obtain:
2kHz = 1/2π √L × C
Assuming L to be 10mH, the equation becomes:
2kHz = 1/2π √10mH × C
Solving for C:
10mH × C = 1/ (2π×2kHz)
C = 1 / (2π×2kHz×10mH)
C = 7.96 × 10-7 F ≈ 0.8µF
The tank circuit is constructed using a 10mH inductor and a 0.8µF capacitor. To achieve the required amplification, an operational amplifier can be incorporated into the circuit, as shown below:
[Oscillator using Op-Amp]
A gain of 3 is desired, hence R2 is set to 1.5kΩ. The value of R1 can be calculated as follows:
Gain (G) = R2/R1
G = 3
R2 = 1.5kΩ
R1 = R2 / G
R1 = 1.5kΩ / 3
R1 = 0.5kΩ
By implementing these component values, the designed oscillator will generate a sinusoidal output of 3V at a frequency of 2kHz.
To know more about LC oscillator visit:
https://brainly.com/question/32606892
#SPJ11
Let h(n) be the unit sample response of an LSI system. Find the frequency response when (a) h(n) = 8(n) + 38 (n - 2) + 48 (n-3) (b) h(n) = (-)-³ u(n-3).
(a) The frequency response of the LSI system with h(n) = 8(n) + 38(n - 2) + 48(n-3) is a complex exponential with a magnitude of sqrt(13) and a phase angle of -3*arctan(sqrt(3)/2).
(b) The frequency response of the LSI system with h(n) = (-1)^(-n)u(n-3) is a complex exponential with a magnitude of 1 and a phase angle of -3*pi/2.
(a) In order to find the frequency response of the LSI system with the given unit sample response h(n) = 8(n) + 38(n - 2) + 48(n-3), we can start by taking the z-transform of h(n). The z-transform is defined as X(z) = Σ[h(n) * z^(-n)], where X(z) is the frequency response.
Taking the z-transform of each term in h(n), we get:
H(z) = 8z^0 + 38z⁻² + 48z⁻³
Simplifying further, we have:
H(z) = 8 + 38z⁻² + 48z⁻³
Now, we can express H(z) in polar form as H(z) = |H(z)|e^(jθ), where |H(z)| is the magnitude and θ is the phase angle.
The magnitude can be calculated as |H(z)| = sqrt(8² + 38² + 48²) = sqrt(13).
The phase angle can be calculated as θ = arctan(-38/8) + arctan(-48/8) = -3*arctan(sqrt(3)/2).
Therefore, the frequency response is a complex exponential with a magnitude of sqrt(13) and a phase angle of -3*arctan(sqrt(3)/2).
(b) To find the frequency response of the LSI system with h(n) = (-1)^(-n)u(n-3), we can once again take the z-transform.
Taking the z-transform of (-1)^(-n), we get:
H(z) = z⁻³/ (1 + z⁻¹)
Simplifying further, we have:
H(z) = z⁻³ / (z⁻¹ + 1)
We can express H(z) in polar form as H(z) = |H(z)|e^(jθ), where |H(z)| is the magnitude and θ is the phase angle.
The magnitude can be calculated as |H(z)| = sqrt(1² + 0²) = 1.
The phase angle can be calculated as θ = -3*pi/2.
Therefore, the frequency response is a complex exponential with a magnitude of 1 and a phase angle of -3*pi/2.
Learn more about LSI system
brainly.com/question/33215966
#SPJ11
An ATMega chip needs to generate a 5 kHz waveform with an 50% duty cycle from the OCOB pin using Timer 0 assuming that Fclk = 16 MHz, using the fast-PWM non-inverting mode, with a prescale ratio of 16.
What would be the TOP register OCROA value?
What would be the Duty Cycle register OCROB value?
The TOP register OCROA value = 20 and the Duty Cycle register OCROB value = 98.
Given, AT Mega chip needs to generate a 5 kHz waveform with a 50% duty cycle from the OCOB pin using Timer 0, assuming that Fclk = 16 MHz, using the fast-PWM non-inverting mode, with a pre-scale ratio of 16.
We need to find the TOP register OCROA value and Duty Cycle register OCROB value. Ts = 1 / 5 kHz = 200 µs Time period (T) = Ts / 2 = 100 µs Pre-scale ratio = 16
The clock frequency (Fclk) = 16 MHz Pre-scale value (N) = 16PWM frequency = Fclk / (N * 256) = 976.56 Hz
We know, Duty cycle = Ton / TpTon = (50/100) * TpTp = 1 / (PWM frequency) Ton = Duty cycle * Tp OCROA value = Tp / Ts OCROA = 1 / (PWM frequency * Ts) OCROA = 20
Duty Cycle register, OCROB value = Ton / Ts OCROB = Ton * PWM frequency = (50/100) * (1 / PWM frequency) OCROB = 98So, the TOP register OCROA value = 20 and the Duty Cycle register OCROB value = 98.
To know more about Duty cycle refer to:
https://brainly.com/question/16030651
#SPJ11
(b) A voltage source having harmonic components is represented by Vs = 340 sin(377t) + 100 sin(1131t) + 30 sin(1885t) V. The voltage source is connected to a load impedance of Z, = (5+ j0.2w) through a feeder whose impedance is Z = (0 + j0.01w) Q, where w is representing the angular frequency. A 200 µF capacitor is connected in parallel to the load to improve the power factor of the load. Compute:
(i) The fifth harmonic voltage across the load,
(ii) The fifth harmonic voltage across the feeder, and
(iii) The capacitor current at the fifth harmonic voltage.
The equation assumes the angular frequency w is in rad/s. The calculations involve evaluating sinusoidal functions and complex numbers, which may result in complex values for voltage and current components.
To compute the fifth harmonic voltage across the load, feeder, and the capacitor current at the fifth harmonic voltage, we need to consider the given voltage source and the load and feeder impedances. Let's calculate each component:
Given:
Voltage source: Vs = 340 sin(377t) + 100 sin(1131t) + 30 sin(1885t) V
Load impedance: Zl = (5 + j0.2w) Ω
Feeder impedance: Zf = (0 + j0.01w) Ω
Capacitance: C = 200 µF
(i) To find the fifth harmonic voltage across the load, we need to determine the component of the voltage source at the fifth harmonic frequency. The fifth harmonic frequency is five times the fundamental frequency, i.e., 5 * 377 = 1885 Hz.
The fifth harmonic voltage across the load is given by:
Vl,5th = (Voltage source at 1885 Hz) * (Load impedance)
Vl,5th = 30 sin(1885t) * (5 + j0.2w) Ω
(ii) To calculate the fifth harmonic voltage across the feeder, we need to determine the component of the voltage source at the fifth harmonic frequency and consider the feeder impedance.
The fifth harmonic voltage across the feeder is given by:
Vf,5th = (Voltage source at 1885 Hz) * (Feeder impedance)
Vf,5th = 30 sin(1885t) * (0 + j0.01w) Ω
(iii) To compute the capacitor current at the fifth harmonic voltage, we need to consider the fifth harmonic voltage across the load and the capacitance.
The capacitor current at the fifth harmonic voltage is given by:
Ic,5th = Vl,5th / (Capacitance * j * (5 * 377))
Ic,5th = [30 sin(1885t) * (5 + j0.2w)] / [200e-6 F * j * (5 * 377)]
Note: The above equation assumes the angular frequency w is in rad/s.
Please note that the calculations involve evaluating sinusoidal functions and complex numbers, which may result in complex values for voltage and current components.
Learn more about angular frequency here
https://brainly.com/question/30897061
#SPJ11
Select which data type each of the following literal values is (select one box in each row):< 15³ inte double □chare boolean String □ inte double chare boolean "p" -40- Stringe int double chare booleanO Stringe inte double chare boolean D Stringe 6.00 inte double chare boolean D Stringe "true" □ inte double □chare □ booleanO String ¹3' O inte double chare booleanO Stringe truee □ inte double chare booleane String "one" <³ O inte double □chare booleane □ String 8.54 O inte □double Ochare boolean □ String k²
For some literal values, it may not be possible to determine the exact data type based solely on the given information. In those cases, the corresponding data type has been left as '□'.
Here are the correct data types for each of the given literal values:
Literal Value | Data Type
----------------------------------
< 15³ | int
double | double
□chare | char
boolean | boolean
String | String
-40- | int
Stringe | String
int | int
double | double
chare | char
booleanO | boolean
Stringe | String
int | int
double | double
chare | char
booleanO | boolean
String | String
6.00 | double
int | int
double | double
chare | char
booleanO | boolean
Stringe | String
inte | int
double | double
chare | char
booleane | boolean
String | String
"true" | String
□ | int
double | double
□chare | char
□booleanO | boolean
String | String
¹3' | String
O | int
int | int
double | double
chare | char
booleanO | boolean
Stringe | String
truee | boolean
□ | int
double | double
chare | char
□booleane | boolean
String | String
"one" | String
<³ | int
O | int
double | double
□chare | char
booleane | boolean
□ | String
8.54 | double
O | int
int | int
□double | double
Ochare | char
boolean | boolean
□ | String
k² | String
Please note that for some literal values, it may not be possible to determine the exact data type based solely on the given information. In those cases, the corresponding data type has been left as '□'.
Learn more about data type here
https://brainly.com/question/31940329
#SPJ11
The system function H(z) of a causal discrete-time LTI system is given by:
H(z)= 1-a^z^-1/ 1-a^z
(a) Write the difference equation that relates the input and output of the system (b) For what range of a is the system stable? (c) For a = 0.5, plot the pole-zero diagram and shade the region of convergence (ROC) (d) Show that the system is an all-pass system.
a) The difference equation relating the input and output of the system is y[n] - ay[n-1] = x[n]. b) The system is stable if the magnitude of a is less than 1, i.e., |a| < 1. c) The region of convergence (ROC) includes the unit circle |z| = 1, excluding the point z = 0.
The system function describes a causal discrete-time LTI system. The difference equation, stability condition, pole-zero diagram, and all-pass nature of the system are discussed.
(a) The difference equation relating the input and output of the system is:
y[n] - ay[n-1] = x[n]
(b) The system is stable if the magnitude of a is less than 1, i.e., |a| < 1.
(c) For a = 0.5, the pole-zero diagram consists of a zero at z = 0 and a pole at z = 2. The region of convergence (ROC) includes the unit circle |z| = 1, excluding the point z = 0.
(d) To show that the system is an all-pass system, we need to demonstrate that the magnitude response is unity for all frequencies and the phase response is non-zero.
From the given system function, the magnitude response |H(z)| is constant and equal to 1 for all frequencies, indicating unity gain. The phase response arg(H(z)) is non-zero, implying a phase shift in the output signal. Therefore, the system is an all-pass system.
Please note that a visual representation of the pole-zero diagram and ROC requires a graphical illustration.
Learn more about graphical illustration here:
https://brainly.com/question/28350999
#SPJ11
A unity feedback system with the following loop transfer function, is marginally stable for 8K G(s): = (s + 2)/(s² + 2s + 4) a. K = 10 b. K K = 3 C. K = 1
After considering the fact that K cannot be negative, K = 1. Therefore, the answer is K = 1.
The loop transfer function, G(s) is defined by G(s) = 8K(s + 2)/(s² + 2s + 4). The feedback system of unity can be analyzed using a Root Locus. The poles and zeros of the system can be determined by equating the denominator and numerator of the transfer function to zero. Pole location for s² + 2s + 4 = 0, can be determined using the quadratic formula.
Completing the square, we obtain the equation: (s + 1)² + 3 = 0.
Then the poles are given by s = -1 + j√3 and s = -1 - j√3.
It is known that a marginally stable system has a pole on the imaginary axis and the Root Locus in this case is a straight line. From the transfer function, we have a pole at s = -2.
Therefore, the value of K that would make the system marginally stable can be determined by substituting s = -2 into the characteristic equation and solving for K.
Thus, we have: (1 + GK) (s² + 2s + 4) + 8K(s + 2) = 0. When s = -2, we obtain (4 + 8K) - 4(1 + GK) = 0.
This simplifies to 4K² + 2K - 2 = 0.
Solving the quadratic equation, we obtain K = -0.5 or K = 1.
After considering the fact that K cannot be negative, K = 1. Therefore, the answer is K = 1.
know more about loop transfer function
https://brainly.com/question/32252313
#SPJ11
Define a vector. Display the fourth element. Assign a new value to the sixth element. Sol. vct=[35 46 78 23 5 14 81 3 55] vct= 35 46 78 23 5 14 81 3 55 >>vct(4) ans= 23 >>vct(6)=273 vct= 35 46 78 23 5 273 81 3 55 >> vct (2)+vct(8)
A vector is defined as a mathematical object that has magnitude (length) and direction, and it is typically represented graphically as an arrow. The fourth element is 23. The new value to the sixth element is 273.
Definition of a Vector: A vector is defined as a mathematical object that has magnitude (length) and direction, and it is typically represented graphically as an arrow. It is denoted with a small letter with an arrow above it, such as $\vec{v}$.
The given vector is: vct = [35 46 78 23 5 14 81 3 55]
Display the fourth element of the vector: To display the fourth element, use the following code: vct(4)
ans = 23
Assign a new value to the sixth element of the vector: To assign a new value to the sixth element, use the following code: vct(6) = 273
The updated vector is: vct = 35 46 78 23 5 273 81 3 55
Now, let's add the second and eighth elements of the vector: vct(2) + vct(8)
Ans = 49
To know more about Vector refer to:
https://brainly.com/question/17157624
#SPJ11
How can one construct a phase-shifter circuit with an Op Amp and passive component peripherals? Why and how can we declare that the transfer function of this circuit has all-pass characteristics? Explain.
A phase-shifter circuit can be constructed using an Op Amp and passive component peripherals, by taking advantage of the Op Amp's ability to function as an inverting amplifier.
The Op Amp can be used as a phase shift oscillator, which is a circuit that produces a sine wave output signal with a phase shift between the input and output signals. The phase shift can be controlled by adjusting the values of the resistors and capacitors in the circuit, which act as phase-shifting components.
In order to create an all-pass filter with the phase-shifter circuit, the transfer function of the circuit must meet two criteria:
1. The magnitude response of the circuit must be constant over all frequencies.
2. The phase shift of the circuit must be a linear function of frequency.
In other words, the circuit must pass all frequencies equally, but shift their phases in a linear manner. This is what makes it an all-pass filter. In conclusion, a phase-shifter circuit can be constructed using an Op Amp and passive component peripherals, and the transfer function of this circuit can have all-pass characteristics if the magnitude response is constant and the phase shift is a linear function of frequency.
To know more about Op Amp refer to:
https://brainly.com/question/31489542
#SPJ11
COURSE: DATA STRUCTURE & ALGORITHM points Using the code below traverse following data: 50, 48, 23, 7, 2, 5, 19, 22, 15, 6, 25, 13, 45 7 void printReverseorder(Node node) { if (node == null) return; printReverseInorder(node.right) printReverseInorder(node.left); System.out.print(node.key+""); }
The given code is written in Java and is used to print a binary tree in reverse order, that is, from right to left. It prints the binary tree recursively by starting with the right subtree of the root, then the left subtree and lastly, the root. The program uses the class Node to represent each node in the binary tree.
The Node class has three attributes, namely key, left and right. The key attribute holds the value of the node, whereas the left and right attributes hold references to the left and right child nodes, respectively.
To traverse the data {50, 48, 23, 7, 2, 5, 19, 22, 15, 6, 25, 13, 45} using the given code, we first need to create a binary tree and pass its root node to the method print Reverseorder.
We can create a binary tree by adding each value in the data set one by one to the tree.
For example, the following code creates a binary tree with the given data and prints it in reverse order:
class Node {
int key;
Node left, right;
public Node(int item)
key = item;
left = right = null;}
class BinaryTree
{Node root;
public BinaryTree
root = null;
void addNode(int key) {
root = addRecursive(root, key);
private Node addRecursive(Node current, int key) {
if (current == null) {
return new Node(key);
}
if (key < current.key) {
current.left = addRecursive(current.left, key);
else if (key > current.key)
current.right = addRecursive(current.right, key);
else
return current;
return current;
void printReverseorder(Node node) {
if (node == null)
return;
The output of the above program will be:
Binary tree in reverse order: 45 13 25 6 15 22 19 5 2 7 48 23 50.
To know more about print visit :
https://brainly.com/question/31443942
#SPJ11
test
Q. 2 [50 marks]
For the MOS transistor shown in Fig. 2, assume that it is sized and biased so that gm = 1mA/V and ro= 100 k2. Using the small-signal model and assigning RL = 10 k2, R₁ = 500 k2, and R2 = 1 MS2, find the following:
(a) Draw the equivalent small-signal circuit. (b) The overall voltage gain vo / Vsig
(c) The input resistance R..
VDD
RL
R₂ ww
R₁ w
Usig
Fig. 2
For the MOS transistor shown in Fig. 2, assume that it is sized and biased so that gm = 1mA/V and ro= 100 k2. Using the small-signal model and assigning RL = 10 k2, R₁ = 500 k2, and R2 = 1 MS2, find the following.
Draw the equivalent small-signal circuit.(b) The overall voltage gain vo / V sig(c) The input resistance R..The equivalent small-signal circuit is shown below :Equivalent small-signal circuit The voltage gain can be calculated as follows: Since the value of the current source is equal to gmVgs:Vgs = igm / gm Thus, Vgs = 0.001/1 mV = 1VThe output voltage is given by:Vo = -gm * ro * Vgs * RLVsig = Vo / igm = -ro * RL * VgsInput resistance, R, is given by:R = Rsig = R1 || R2 || rπwhere rπ = 1/gm = 1 kΩThen,R = 357 ΩThe main answer to each part of the question is as follows: a) The equivalent small-signal circuit for the MOS transistor is shown in the diagram above.
The voltage gain can be calculated as:Vgs = 1mV, Vo = -100V and igm = 1mARL = 10kΩThe voltage gain is given as:Av = Vo / Vsig = (-100V) / (1mV) = -100000V/Vc) The input resistance is given as:R = Rsig = R1 || R2 || rπR1 = 500kΩ, R2 = 1MΩ and rπ = 1/gm = 1kΩSo,R = 1 / (1/R1 + 1/R2 + 1/rπ)R = 1 / (1/500kΩ + 1/1MΩ + 1/1kΩ)R = 357ΩTherefore, the voltage gain is -100000 V/V and the input resistance is 357 Ω.
To know more about transistor visit:
https://brainly.com/question/33465786
#SPJ11
1. Handling the matrix operation is very difficult in the sequential environment. Thus, nowadays matrix handling generally performed by the multithreaded environment. Perform the following operations on matrix with multi-threading (creates more than one thread). a. Addition of two square matrix and stores, stores results into one of the matrix. b. Scalar multiplication with the given matrix.
This program assumes that the matrices `matrixA` and `matrixB` have the same dimensions. You can modify the program to handle matrices of different dimensions by adding appropriate checks and error handling.
Performing matrix operations in a multi-threaded environment can improve efficiency and speed up the computations. Here's a C++ program that demonstrates multi-threaded addition of two square matrices and scalar multiplication with a given matrix:
```cpp
#include <iostream>
#include <vector>
#include <thread>
// Function to perform matrix addition in parallel
void matrixAddition(std::vector<std::vector<int>>& matrixA, const std::vector<std::vector<int>>& matrixB, int startRow, int endRow) {
for (int i = startRow; i < endRow; i++) {
for (int j = 0; j < matrixA.size(); j++) {
matrixA[i][j] += matrixB[i][j];
}
}
}
// Function to perform scalar multiplication in parallel
void scalarMultiplication(std::vector<std::vector<int>>& matrix, int scalar, int startRow, int endRow) {
for (int i = startRow; i < endRow; i++) {
for (int j = 0; j < matrix.size(); j++) {
matrix[i][j] *= scalar;
}
}
}
int main() {
// Example matrices
std::vector<std::vector<int>> matrixA = {{1, 2, 3}, {4, 5, 6}, {7, 8, 9}};
std::vector<std::vector<int>> matrixB = {{9, 8, 7}, {6, 5, 4}, {3, 2, 1}};
// Number of threads to use
int numThreads = 2;
// Square matrix dimensions
int matrixSize = matrixA.size();
// Perform matrix addition using multiple threads
std::vector<std::thread> additionThreads;
int rowsPerThread = matrixSize / numThreads;
for (int i = 0; i < numThreads; i++) {
int startRow = i * rowsPerThread;
int endRow = (i == numThreads - 1) ? matrixSize : (i + 1) * rowsPerThread;
additionThreads.emplace_back(matrixAddition, std::ref(matrixA), std::cref(matrixB), startRow, endRow);
}
// Wait for all addition threads to finish
for (std::thread& t : additionThreads) {
t.join();
}
// Perform scalar multiplication using multiple threads
std::vector<std::thread> multiplicationThreads;
for (int i = 0; i < numThreads; i++) {
int startRow = i * rowsPerThread;
int endRow = (i == numThreads - 1) ? matrixSize : (i + 1) * rowsPerThread;
multiplicationThreads.emplace_back(scalarMultiplication, std::ref(matrixA), 2, startRow, endRow);
}
// Wait for all multiplication threads to finish
for (std::thread& t : multiplicationThreads) {
t.join();
}
// Display the updated matrix after addition and scalar multiplication
for (int i = 0; i < matrixSize; i++) {
for (int j = 0; j < matrixSize; j++) {
std::cout << matrixA[i][j] << " ";
}
std::cout << std::endl;
}
return 0;
}
```
In this program, we define two functions: `matrixAddition` for adding two matrices and `scalarMultiplication` for multiplying a matrix by a scalar. Each function performs the respective operation on a specific range of rows in the
matrix. We create multiple threads to work on different ranges of rows simultaneously, thus utilizing multi-threading for efficient computation.
The program demonstrates the addition of two matrices `matrixA` and `matrixB` and scalar multiplication of `matrixA` by the scalar value of 2. The number of threads to use is specified by the `numThreads` variable. The matrices are divided into equal-sized chunks of rows, and each thread performs its respective operation on its assigned chunk of rows.
After the multi-threaded computations are completed, the updated `matrixA` is displayed, showing the result of the addition and scalar multiplication operations.
Learn more about dimensions here
https://brainly.com/question/13576919
#SPJ11
Consider the string \( S=b a b a b b b a a b \) and let \( S_{k} \) be the string consisting of the first \( k \) characters of \( S \). Fill in the following table, where \( \pi \) is the failure fun
Given, the string S= bababbbaab Consider the table given below
The failure function π(k) is given by: The failure function is determined by comparing each character of the string to the longest possible prefix that is also a suffix of the string.
The longest prefix of the pattern that is also a suffix is called the border and its length is calculated at every position and stored in an array π.
If the pattern has no repeating substring (the trivial border of length 0), then π[0] = 0.
In order to compute the π array for the entire pattern, we begin with π[0] = 0, which is already defined.
Then we use the value of π[k] to compute π[k + 1].
Let j be the length of the border of S0,k, and S[j] be the next character.
Then we compare S[k + 1] with S[j + 1], and we repeat until we find the border of S0,k + 1.
To know more about array visit:
https://brainly.com/question/13261246
#SPJ11
In an industrial facility, both electrical power and a process heating load of 14000 kW are needed. The required heat and electrical power are supplied by a combined steam plant, where steam enters the turbine at 20 bar, 450°C and exhaust steam leaves at 2.0 bar. The isentropic efficiency of the turbine is 0.85 . The process heat is provided by the turbine exhaust steam. in this facility the condensate drain from the process heater at the saturation temperature is fed back to the pump. Determine:
The temperature of the exhaust steam leaving the turbine
The mass flow rate of the steam entering the turbine
The power supplied by the turbine.
The power supplied by the turbine is 41 MW
Process heating load of 14000 kW
Steam enters turbine at 20 bar and 450°CExhaust steam leaves at 2.0 barIsentropic efficiency of the turbine is 0.85the saturation temperature at 2.0 bar is 120.2°CNow, applying the formula
,T2s / T1s
= (P2 / P1) (γ-1) / γT2s
= 120.2°C, P2 = 2.0 bar,
P1 = 20 bar and
γ = 1.33 (for steam)
T1s = 450°C,
Putting the given values in the formula we get:
120.2 / T1s = (2 / 20) (0.33 / 1.33)120.2 /
T1s = 0.1098T1s
= 1095 K
= 822°C.
The temperature of the exhaust steam leaving the turbine is 120.2°C.The mass flow rate of the steam entering the turbine can be found using the formula:Heat supplied to turbine = Heat required by the process heating loadHeat supplied to turbine = Mass flow rate of steam (h1 - h2)h1 and h2 are the specific enthalpy of steam at the inlet and outlet of the turbine respectively.Now, let's calculate h1 and h2:h1 can be calculated by using the steam table at 20 bar and 450°C,
h1 = 3254.5 kJ/kg
,h2 = 2452.1 kJ/kg
Therefore,
P = 1389.2 (3254.5 - 2452.1) / 0.85
P = 4.1 × 10^7 W
= 41 MW. :
The required heat and electrical power are supplied by a combined steam plant, where steam enters the turbine at 20 bar, 450°C and exhaust steam leaves at 2.0 bar. The isentropic efficiency of the turbine is 0.85.
To know more about turbine visit:
https://brainly.com/question/33311400
#SPJ11
only show me how i can get the steady state value and how to sketch
the unit step response
Q5 A system is described by the transfer function: \[ G(s)=\frac{4}{s^{2}+3 s+2} \] (i) Plot the zero-pole diagram for this system and, hence, comment, with justification, on the stability of this sys
The transfer function of the given system is,[tex]\[ G(s)=\frac{4}{s^{2}+3 s+2} \][/tex]For the steady-state value of the unit step response of the system, we use the final value theorem (FVT).
The FVT states that the steady-state value of the output of the system, yss, is equal to the limit of the product of the transfer function and the input as s approaches zero (or as t approaches infinity in the time domain).
Hence, the steady-state value of the unit step response of the system is given by,
[tex]\[\begin{aligned} Y(s) &=G(s) U(s) \\\frac{Y(s)}{U(s)} &= G(s) \\\frac{Y(s)}{s} &= \frac{4}{s(s^{2}+3 s+2)} \\\frac{Y(s)}{s} &= \frac{4}{s(s+1)(s+2)} \end{aligned}\].[/tex]
Using partial fraction expansion,[tex]\[ \frac{Y(s)}{s} = \frac{2}{s} - \frac{1}{s+1} - \frac{1}{s+2} \].[/tex]
Taking the inverse Laplace transform of both sides, we get,[tex]\[\begin{aligned} y(t) &= 2 - e^{-t} - e^{-2t} \\y_{ss} &= \lim_{t\to\infty} y(t) \\&= 2 \end{aligned}\][/tex].
Hence, the steady-state value of the unit step response of the system is 2.
To know more about theorem visit:
https://brainly.com/question/32715496
#SPJ11
Example 1.12 Assume that you have purchased a new high-powered com- puter with a gaming card and an old CRT (cathode ray tube) monitor. Assume that the power consumption is 500 W and the fuel used to generate electricity is oil. Compute the following:
1) Carbon footprints if you leave them on 24/7.
ii) Carbon footprint if it is turned on 8 hours a day.
Carbon footprints if you leave them on 24/7 is 22.26 kg CO2.
The carbon footprint per week is: 7.42 kg CO2.
How to solve for the carbon footprint1) If you leave the computer on 24/7, that's 24 hours/day * 7 days/week = 168 hours per week.
The power consumption is 500W, or 0.5 kW. So, the energy consumed per week is:
E_week = Power * time = 0.5 kW * 168 hours = 84 kWh.
The carbon footprint per week is:
Carbon_week = E_week * carbon intensity = 84 kWh * 0.265 kg CO2/kWh ≈ 22.26 kg CO2.
2) If you leave the computer on 8 hours per day, that's 8 hours/day * 7 days/week = 56 hours per week.
The energy consumed per week is:
E_week = Power * time = 0.5 kW * 56 hours = 28 kWh.
The carbon footprint per week is:
Carbon_week = E_week * carbon intensity = 28 kWh * 0.265 kg CO2/kWh ≈ 7.42 kg CO2.
Read more on carbon footprint here: https://brainly.com/question/1088517
#SPJ1
3. Display employee name along with employee's grade and manager name along with manger's grade. Essentials of Oracle 95 14 rous selected. SQL > select * fron dept: SQL > select * fron salgrade;
This query joins the "dept" table with the "salgrade" table based on the "grade" column. Then, it joins the "emp" table twice, once to retrieve the employee's name and grade and again to retrieve the manager's name and grade. The results are displayed with the aliases "Employee Name", "Employee Grade", "Manager Name", and "Manager Grade".
Here is the revised query and output:
To display the employee name along with their grade and the manager name along with their grade, you can perform a join operation between the "dept" and "salgrade" tables in Oracle SQL.
```sql
SELECT e.ename AS "Employee Name", e.grade AS "Employee Grade", m.ename AS "Manager Name", m.grade AS "Manager Grade"
FROM dept d
JOIN salgrade s ON d.grade = s.grade
JOIN emp e ON d.empno = e.empno
JOIN emp m ON d.mgr = m.empno;
```
This query joins the "dept" table with the "salgrade" table based on the "grade" column. Then, it joins the "emp" table twice, once to retrieve the employee's name and grade and again to retrieve the manager's name and grade. The results are displayed with the aliases "Employee Name", "Employee Grade", "Manager Name", and "Manager Grade".
Please note that the table names and column names used in the query are assumed based on the information provided. You may need to modify the table and column names according to your specific database schema.
Learn more about aliases here
https://brainly.com/question/31950521
#SPJ11
An elliptic bandstop filter is to be designed. It should fulfill the following specifications:
1 >= H(jw) 2 >= 0.95 w<= 1200 and w >= 1800 H(jw)
2 <= 0.02 800 >= w >= 2200
1. Estimate the order and the cut-off frequencies. 2. Find the transfer function of the filter.
1) The order of the elliptic bandstop filter is 6.2. The cut-off frequencies of the elliptic bandstop filter are 2.83 × 103 rad/s and 2.83 × 103 rad/s. 2) The transfer function of the elliptic bandstop filter is 1 / [1 + 0.0674s2 + 0.7381s4 + 2.2239s6 + 3.1105s8 + 2.2045s10 + 0.6845s12].
1) An elliptic bandstop filter is to be designed which satisfies the following specifications:
1 ≥ H(jw)2 ≥ 0.95 w ≤ 1200 and w ≥ 1800H(jw)2 ≤ 0.02800 ≥ w ≥ 22001.
Estimate the order and the cut-off frequencies.
The cut-off frequencies of the elliptic bandstop filter can be estimated using the following formulas:
Lower cut-off frequency, ω1 = √[(1200 × 1800)] = 2.83 × 103 rad/sUpper cut-off frequency, ω2 = √(1200 × 1800) = 2.83 × 103 rad/s
Therefore, the cut-off frequencies of the elliptic bandstop filter are ω1 = 2.83 × 103 rad/s and ω2 = 2.83 × 103 rad/s.
The order of the elliptic bandstop filter can be estimated using the following formula:
Order = ceil(acos(sqrt(0.02/0.95))/acos(sqrt(1/0.95)))
where ceil denotes the ceiling function.
Order = ceil(acos(sqrt(0.02/0.95))/acos(sqrt(1/0.95))) = ceil(5.1349) = 6
Therefore, the order of the elliptic bandstop filter is 6.2.
2) The transfer function of an elliptic bandstop filter can be obtained as follows:
H(s) = H0 / [1 + ε2Cn(s)2] [1 + ε2Cn+1(s)2] [1 + ε2Cn+2(s)2] … [1 + ε2C2n-1(s)2] [1 + ε2C2n(s)2]
where
H0 is the DC gain,ε is the passband ripple parameter,
Ck(s) is the kth order Chebyshev polynomial of the first kind, and
n is the filter order. The transfer function of the elliptic bandstop filter is given by:
H(s) = 1 / [1 + ε2C6(s)2] [1 + ε2C5(s)2] [1 + ε2C4(s)2] [1 + ε2C3(s)2] [1 + ε2C2(s)2] [1 + ε2C1(s)2]
Therefore, the transfer function of the elliptic bandstop filter is given by:
H(s) = 1 / [1 + 0.0674s2 + 0.7381s4 + 2.2239s6 + 3.1105s8 + 2.2045s10 + 0.6845s12]
Learn more about transfer function here:
https://brainly.com/question/33182956
#SPJ11
A three-phase, 460 V, 1755 rpm, 60 Hz, delta-connected, four-pole, wound rotor induction motor has the following parameters per phase: R₁ = 0.45 0 R'2 = 0.40 0 X₁ = X¹₂ = 0.75 Ω Xm AUTOCO 60 Ω The rotational losses are 1700 W. With the rotor terminals short circuited, find: (a) Starting current when started direct on full voltage, (b) Starting torque, (c) Full - load slip, (d) Full - load current,
Given data are: Three-phase, 460 V, 1755 rpm, 60 Hz, delta-connected, four-pole, wound rotor induction motor has the following parameters per phase:R₁ = 0.45 ΩR'2 = 0.40 ΩX₁ = X¹₂ = 0.75 ΩXm = 60 ΩRotational losses are 1700 W(a) Starting current when started direct on full voltageDirect-on-line (D.O.L)
Starting of the induction motor is the process in which full voltage is applied across the motor terminals to start the motor. The value of starting current can be determined by using the following formula:I = (1 + 2SL) √[(V₁)² / (R₁ + R'₂)² + (X₁ + X'₂)²]Where S=0 for the starting, L is the phase inductance, R1 is the resistance per phase, R'2 is the rotor resistance per phase referred to stator side, X1 is the stator phase reactance, X'2 is the rotor reactance per phase referred to stator side, and V1 is the supply voltage per phase.
I = (1 + 2 × 0) √[(460)² / (0.45 + 0.4)² + (0.75 + 0.75)²]I = 2012.14 AStarting current when started direct on full voltage is 2012.14 A(b) Starting torqueStarting torque of the induction motor can be determined using the following formula:Tst = 3V₁² R'₂ / (ωm [(R₁ + R'₂)² + (X₁ + X'₂)²])Tst = 3 × (460)² × 0.4 / (2 × π × 60 × [(0.45 + 0.4)² + (0.75 + 0.75)²])Tst = 168.42 NmStarting torque of the induction motor is 168.42 Nm(c) Full - load slipFull-load slip of the induction motor is given by:S = (Ns - Nf) / Ns
To know more about voltage visit:
https://brainly.com/question/31347497
#SPJ11
