Values popped in this order: h, s, and f. Condition of stack: m, d (from top to bottom).
This is presumable if the stack is initially empty. Suppose that p contains the pops' values. The stack's status is indicated by where the top and bottom of the stack point. The top of the stack is the point where a new value is entered and an old value is removed. This is how it happens: pushes d into the stack to insert it (d). D->top in the stack. pushes into the stack and enters h (h). H -> top. bottom of stack By using pop (): d -> top, d. h gets removed from the stack. If p contains popped values, then h should be placed into p as the first popped value. p = h. pushes f into the stack to insert it (f). F -> top. D -> bottom of stack. Stack.
Learn more about The stack here:
https://brainly.com/question/17177482
#SPJ4
Determine the length of welds required to transmit a load 54.5 KN between 12.7mm. thick plates, when the plates are to be joined by 1) Two parallel fillet welds. 2) Two transverse fillet welds.
For the parallel fillet weld, the length required is 24.52mm and for transverse fillet welds, the longer fillet weld required is 24.39 mm and the length of the shorter fillet weld required is 6.13 mm.
What is the length to transmit the loadThe length of weld required to transmit a load between two plates depends on the type of weld used and the strength of the material being welded. For the given scenario:
Two parallel fillet welds:
The length of each fillet weld required can be calculated using the following formula:
L = (2 x F x P) / (0.7 x T)
where L is the length of each fillet weld, F is the applied force (54.5 KN), P is the perimeter of the weld (2 x length of the joint), T is the thickness of the plate (12.7 mm), and 0.7 is a constant. Substituting the values, we get:
L = (2 x 54.5 x 2) / (0.7 x 12.7) = 24.52 mm
Therefore, the length of each fillet weld required is 24.52 mm.
Two transverse fillet welds:
The length of each fillet weld required in this case can be calculated using the same formula as above, but with the perimeter of the weld being the sum of the lengths of the two sides being welded. Since the two fillet welds are transverse, their lengths will be different. Assuming one fillet weld is longer than the other, we can calculate their lengths as follows:
L1 = (F x P1) / (0.7 x T)
L2 = (F x P2) / (0.7 x T)
where L1 and L2 are the lengths of the two fillet welds, P1 and P2 are the perimeters of the two sides being welded, and all other variables are the same as before. We can assume that the longer fillet weld is on the side with the higher applied force, so we have:
P1 = 2 x length of joint
P2 = length of joint
Substituting the values, we get:
L1 = (54.5 x 2 x 2) / (0.7 x 12.7) = 24.39 mm
L2 = (54.5 x 1) / (0.7 x 12.7) = 6.13 mm
Therefore, the length of the longer fillet weld required is 24.39 mm and the length of the shorter fillet weld required is 6.13 mm.
Learn more on applied force here;
https://brainly.com/question/25732012
#SPJ1
the best vacations include excellent accommodations, like 10 boutique hotels we discovered with a local focus. to which city did we travel to stay in an 1867 mansion built by a famed architect, with custom wallpaper weaving in local history?
Travel and history go hand - in - hand. History provides us with a broad grasp of a past, whereas travel links the past to the present and enables us to comprehend its importance both now and in the future.
Why is being naturally good?Use in a casual way to express that something is obvious to you and actually not shocking given the circumstances. Everybody gets frustrated and disappointed when things go bad. People were naturally interested in such arrivals and departures. Naturally, he had already been horrified and furious.
What, in plain English, does nature mean?All non-human produced objects on the planet, such as all animals, vegetation, as well as other living creatures, and all natural phenomena, are collectively referred to as nature. The
To know more about naturally visit:
https://brainly.com/question/20378345
#SPJ4
how is an nmos and gate implemented? group of answer choices a single nmos transistor. 2 nmos transistors in series. 2 nmos transistors in parallel. the output of 2 nmos transistors in series connected to the input of a single nmos transistor. the output of 2 nmos transistors in parallel connected to the input of a single nmos transistor. the output of a single nmos transistor connected to the input of 2 nmos transistors in series. the output of a single nmos transistor connected to the input of 2 nmos transistors in parallel.
An nmos and gate can be implemented using 2 nmos transistors in series, or the output of 2 nmos transistors in parallel connected to the input of a single nmos transistor.
Implementing an nmos AND gate using two transistors in series or in parallelIn the first implementation, the two nmos transistors are connected in series, with the input signal connected to the gate of the first transistor and the output taken from the drain of the second transistor. When the input signal is high, the first transistor is turned on, allowing current to flow to the second transistor. If the second transistor is also turned on, the output will be low, otherwise, the output will be high.
In the second implementation, the two nmos transistors are connected in parallel, with their sources and gates connected together, and the output taken from the drains. When the input signal is high, both transistors are turned on, allowing current to flow to the output. If either of the transistors is turned off, the output will be low.
Both of these implementations use two nmos transistors, but they are connected differently to achieve the desired logic function. A single nmos transistor can be used to implement a NOT gate or an inverter, but it cannot implement an AND gate
To know more about transistors, visit:https://brainly.com/question/29731975
#SPJ4
Dante uses ______ DSCP tags for QoS.
Dante employs layer 3 QoS tagging called DSCP (Diffserv).
What does DSCP mean?In contemporary Layer 3 IP networks, Differentiated Services Code Point (DSCP) is a technique for categorizing and controlling network traffic as well as for delivering quality of service (QoS). Differentiated services, also known as DiffServ, is an IP-based computer networking architecture that defines a method for categorizing, controlling, and delivering quality of service to network traffic on contemporary IP networks. DSCP Score. Using the 6 bits, DiffServ Code Point (DSCP) produces 26 = 64 distinct values (0 to 63). describes the values of the DSCP standards. The remaining DSCP values can be altered to meet the QoS specifications.
How does DSCP QoS work?Network data traffic classification is determined by Quality of Service (QoS) DSCP Marking. This can be used to identify the network traffic that uses more bandwidth, is more important, and has a higher chance of dropping packets.
To know more about DSCP visit:
https://brainly.com/question/29590727
#SPJ1
