The beaker of orthoxylene was put inside a sealed tank containing orthoxylene gas at 142. degree C and 893. torr will have the same amount of liquid inside it after ten minutes because the system is a closed system as none of the liquid's vapor escapes.
The correct option is the same amount.
A closed system allows energy to enter and exit but not matter to enter or exit. About a closed system is a covered pot on the burner. Both matter and energy cannot enter or leave an isolated system. A thermos or cooler is about as isolated a system as there is.
The beaker of orthoxylene that was put inside a sealed tank containing orthoxylene gas at 142 degrees C and 893 torr is a closed system.
Learn more about a closed system at: https://brainly.com/question/3690180
#SPJ1
Air has a density of 0.001226 g/ml. What volume of air would have a mass of 1.0 lb? How do I arrive at 3.7 x 10^2 l? I understand the math but not how to put it in scientific notation.
Answer:
3.6999 x 10^2 l.
Explanation:
To find the volume of air with a mass of 1 lb, we can use the density formula:
Density = Mass divided by Volume
Rearranging the formula to solve for volume:
Mass / Density = Volume
Given that the density of air is 0.001226 g/ml, and we want to find the volume of 1 lb of air, we can substitute the following values into the equation:
(1 pound) / (0.001226 g/ml)
To convert pounds to grams, 1 pound equals 453.59 grams.
Volume = 453.59 g/0.001226 g/ml = 369,988.6 ml
Now we can convert from milliliters to liters. 1 liter equals 1,000 milliliters.
Volume = 369.99 l/1000 = 369,988.6 ml
To express it in scientific notation, you can use a factor of 10 to represent the decimal place. You move the decimal point of the number to the left or right until you have only one non-zero digit to the left of the decimal point.
369.99 l = 3.6999 x 10^2 l
So the volume of 1 lb of air is 3.6999 x 10^2 l.
what are the two terms in the sequence 16,13,10
Answer:
Explanation:
The two terms in the sequence are 16 and 13.
Answer the questions for 100 points!
6) The constant is the amount of beverage in each sample. Option C
7) Greater amount of carbon dioxide dissolve at lower temperatures
8) It shows that the hypothesis should be thrown away. Option D
9) The independent variable is the temperature. Option B
What is an experiment?When we talk about an experiment, then we would have to look at the interplay of one or more variables. It is common that when we are doing an experiment, the dependent variable would have to interface with the independent variable.
We can see that in the experiment, we are trying to find out the impact of the temperature on the mass of the carbon dioxide.
Learn more about the experiment:https://brainly.com/question/30055326
#SPJ1
Please help guys
92.)-For neutralization 31 cm³. 0,16 N. alkali solution
requires 217 cm³. of H₂SO4 solution. What are the normality and
titer of an H₂SO4 solution? Answer: 0.023 n .; 1.127. 10³ g /
cm³.
93)-What volume is 0,3 N. acid solution is required to
neutralize a solution containing 0,32 g of NaOH in 40 cm³?
Answer: 26,6 cm³.
94)- Neutralization of 1 liter of a solution containing 1,4 g of
KOH requires 50 cm³. of an acid solution. Calculate the
normality of the acid solution. Answer: 0,53 n.
95)-What mass of HNO, was contained in the solution if 35
cm3. of 0,4 N was required to neutralize it? NaOH solution?
What is the titer of a NaOH solution? Answer: 0,882 g, 0,016 g/
cm³.
96)-What mass of NaNO, should be dissolved in 400 g of
water to prepare a 20% solution?
To neutralize a solution containing 0.32 g of NaOH in 40 cm3 requires 26.66 cm3 of 0,3 S. a. acid solution.
What does normalcy mean?The quantity of moles per solution liter is how it is defined. It is utilized to calculate the number of grams that make up the solution's entire volume. It is utilized to calculate the mole ratio in the solution's overall volume. Normality is measured in units.
Calculation
How to calculate volume?
N1V1 = N2V2
normality = molarity x basicity
For sulfuric acid, the basicity is 2.
∴N1=0.3N
V1=?
Normality of NaOH is [0.32/(40×40)]×1000
N2=0.2×1=0.2N
V2=40ml
0.3 x V1 = 0.2 x 40
V1 = 26.6 cm³
To know more about normalcy visit:
https://brainly.com/question/30252847
#SPJ1
(ii) At what velocity should a 1:30 scale model be towed through water if the Froude number is to be the same for the model and prototype? [6 marks]
The velocity of the prototype should be (Fr x √(g x (1:30L))).
What is prototype?Prototype is a preliminary version of a product or system that is used to test features, functionality, and design before a final version is released. It is a way to quickly and cheaply test ideas, evaluate feedback, and provide proof-of-concept for a product or system.
The Froude number for the model and prototype is given by the equation, Fr = V/√(gL), where V is the velocity, g is the acceleration due to gravity, and L is the length of the prototype. For the model, V is 1:30 times the velocity of the prototype.
Therefore, the velocity of the prototype, Vp, can be calculated as:
Vp = (Vm x 30)/1
= (Fr x √(gL)) x 30/1
= (Fr x √(g x (1:30L)))
Where Vm is the velocity of the model and L is the length of the prototype.
Therefore, the velocity of the prototype should be (Fr x √(g x (1:30L))).
To learn more about prototype
https://brainly.com/question/29913713
#SPJ1
How many liters of N2 gas at STP are in a deployed car airbag whose N2 gas masses at 43.8 g?
PLEASE HELP
Answer:
490.87 L
Explanation:
Molar mass of N2 = (1 x 2) = 2 g
Moles of N2 in the airbag = 43.8/2 = 21.9 moles
One mole of any gas occupies a volume of 22.414 L at S.T.P
setting up ratio between moles and volume;
moles : volume
1 : 22.414
21.9 : X
X = (21.9 x 22.414)
= 490.87 L
Calculate the relative molecular mass of hydrated Copper (II) tetraoxosulphate (VI) CuSO4.5H₂O (Cu = 64 S = 32 H = 1 0 = 16).
The relative molecular mass of hydrated Copper (II) tetraoxosulphate (VI) CuSO4.5H₂O is 249.
What is molecular mass?Molecular mass is a measure of the total mass of one mole of a substance, which is defined as the mass of the substance divided by the number of molecules it contains. It is typically expressed in g/mol and is also known as molar mass. Molecular mass is determined by the types and number of atoms that compose a molecule, and is an important factor in understanding the properties of a substance.
This is calculated by adding the atomic masses of all the atoms present in the compound.
The atomic mass of copper is 64, sulphur is 32, oxygen is 16, and hydrogen is 1.
So, the relative molecular mass of hydrated Copper (II) tetraoxosulphate (VI) CuSO4.5H₂O is 64 + 32 + (16*4.5) + (1*5) = 249.
To learn more about molecular mass
https://brainly.com/question/24727597
#SPJ1
Explain how you would create a Lewis dot diagram for the following: (1 mark each, 4 marks total) Example: When creating a Lewis Dot diagram for carbon I would look at the periodic table of elements and find that the atomic number is 6. Then I would draw the C. I know that two electrons would go in the first orbit. That leaves 4 electrons in the valence shell. So, the Lewis Dot diagram would look like a C with four dots around it.
a) phosphorus atom
b) chlorine ion
c) beryllium atom
d) calcium ion
a) phosphorus atom - This would have three concentric circles with the outermost circle having five electrons.
b) chlorine ion - This would have three concentric circles with the outermost circle having seven electrons.
c) beryllium atom - This would have two concentric circles with the outermost circle having two electrons
d) calcium ion - This would have four concentric circles with the outermost circle having two electrons.
What is the Lewis dot diagram?We know that the Lewis dot diagram is the kind of representation that can be used to show the number of the electrons that we do have in an element. The number of atoms are shown in electrons that are in the orbits and the orbits are concentric circles that look very similar.
Recall that the orbits that we have in the atom are known to be arranged in energy levels and the energy levels of the atoms of the atoms of the elements play a key role in the Lewis dot structure of the elements that we know.
Learn more about Lewis dot structure:https://brainly.com/question/20300458
#SPJ1
Sherman suggests that reproduction always creates individuals with adaptive traits. Does this seem correct? Why or why not?
If Sherman suggests that reproduction always creates individuals with adaptive traits, then he/she is not correct because variation may lead to non-adaptive phenotypes.
What is the presence of genetic variation in individuals of a given population?The presence of genetic variation in individuals of a given population is not adaptive per se, but instead, it provides the raw material for natural selection that leads to the differential survival and reproduction of the most adaptive phenotypes.
The genetic variation in individuals of a given population does not crate adaptive traits and it may derive from sexual reproduction.
Therefore, with this data, we can see that the presence of genetic variation in individuals of a given population may or not be adaptive in the function of the environment in which the individual produced by means of sexual reproduction is developed and therefore it is an advantage for the population but the individual may be harmful.
Learn more about adaptive genetic variation here:
https://brainly.com/question/29313212
#SPJ1
Write the Net Ionic Equation for the following equations. Molecular Equation: 2AgNO3(aq) + CaBr2(aq) → Ca(NO3)2(aq) + 2AgBr(s) Ionic Equation: 2Ag+(aq) + 2NO3−(aq) + Ca2+(aq) + 2Br−(aq) → Ca2+(aq) + 2NO3−(aq) + 2AgBr(s)
Net Ionic Equation: 2Ag+(aq) + Ca₂ +(aq) + 2Br⁻(aq) → 2AgBr(s)
Net Ionic Formula
A chemical equation for a process called a net ionic equation only includes the species that are involved in the reaction. The spectator ions, which pass through the process unaltered, are not listed.
In this question the steps for this process are as follows:
Step 1: Write out the molecular equation.
2AgNO₃ (aq) + CaBr₂ (aq) → Ca(NO₃)₂ (aq) + 2AgBr (s)
Step 2: Balance the equation.
2AgNO₃ (aq) + CaBr₂ (aq) → Ca(NO₃)₂ (aq) + 2AgBr (s)
Step 3: Write out the ionic equation.
2Ag+ (aq) + 2NO₃⁻ (aq) + Ca₂+ (aq) + 2Br ⁻ (aq) → Ca²⁺ (aq) + 2NO₃⁻ (aq) + 2AgBr (s)
Step 4: Simplify the equation by cancelling out the species that are on both sides of the equation.
2Ag+ (aq) + Ca₂+ (aq) + 2Br⁻ (aq) → 2AgBr (s)
Step 5: The net ionic equation is the final result.
Net Ionic Equation: 2Ag+ (aq) + Ca₂+ (aq) + 2Br ⁻ (aq) → 2AgBr (s)
To learn more about Net Ionic Equation refer :
brainly.com/question/30434449
#SPJ1
an ion of platinum has a mass number of 195 and contains 74 electrons. How many
protons and neutrons does it contain, and what is its charge?
ompound
Answer:
djffffffffffffffffffffffffffffffffffffffffffffffffffffffffffgk
Explanation:
jdrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
which type of particles make up the lattice in a)ionic compounds b) molecular compounds
Answer: a) ions and b) ions
Explanation:
Which factor causes chemical weathering
A gravity
B sunlight
C Acids
D wind
Answer:
C
Explanation:
because its the answer
Answer:
acids
Explanation:
acids because if the rain comes from cloud is acid it can be weathered or if the water is slightly acidic
Cos x tan x - cos x = 0
Answers:
0 + n pi, pi/4 + 2n pi
0 + n pi, 5pi/4 + 2n pi
Pi/2 + n pi, 5pi/4 + 2n pi
Pi/2 + n pi, pi/4 + 2n pi
Answer:0+npipi/4+2npi
Explanation:
Diethyl ether has a ΔHvap of 29.1 kJ/mol and a vapor pressure of 0.703 atm at 25.0°C. What is its vapor pressure at 81.0°C?
The new Vapor pressure of the dietheylether is 6.52 atm.
What is the vapor pressure?We have to note that the vapor pressure would have to do with the ease with which the substance can be converted from liquid to vapor. In this case we can see that we have about two different temperatures and we are trying to obtain the vapor pressure at each of the temperatures that have been given.
Using the formula;
ln(P2/P1) = -ΔHvap/R(1/T2 - 1/T1)
P2 = final pressure
P1 = initial pressure
ΔHvap = Enthalpy of vaporization
R = constant
T = Temperature
ln(P2/0.703) = -29.1 * 10^3/8.314(1/354 - 1/298)
ln(P2/0.703) = -3651.3(0.0028 - 0.0034)
ln(P2/0.703) = 2.19
(P2/0.703) = e^2.19
P2 = e^2.19 * 0.73
P2 = 6.52 atm
It has a vapor pressure of about 6.52 atm.
Learn more about vapor pressure:https://brainly.com/question/25715932
#SPJ1
50 cm³ of 0.50 M sulphuric acid is added to 50 cm³ of 0.10 M sodium hydroxide in a calorimeter. A maximum rise in temperature of 6.8 °C is observed.
a. Calculate the standard enthalpy of neutralization of sulphuric acid and sodium hydroxide. (Ans: −57.12 kJ mol−1)
b. Give reason why the value obtained in (a) is less than the expected value.
Answer:
a. To calculate the standard enthalpy of neutralization of sulphuric acid and sodium hydroxide, we can use the formula:
ΔH_neutralization = q_calorimeter / n_reactant
where q_calorimeter is the heat absorbed or released by the solution and n_reactant is the number of moles of reactant.
First, we need to calculate the heat absorbed or released by the solution using the equation:
q_calorimeter = mcΔT
where m is the mass of the solution, c is the specific heat capacity of the solution and ΔT is the change in temperature.
In this case, the mass of the solution is 50 cm³ + 50 cm³ = 100 cm³. The specific heat capacity of the solution is approximately 4.18 J/g°C. The change in temperature is 6.8°C.
q_calorimeter = (100 cm³) (4.18 J/g°C) (6.8°C) = 28.624 J
Then we need to calculate the number of moles of reactant used. The acid is sulfuric acid and the base is sodium hydroxide.
H2SO4 + 2NaOH -> Na2SO4 + 2H2O
The balanced equation shows that 1 mole of H2SO4 reacts with 2 moles of NaOH.
n_reactant = (50 cm³)(0.50 M) + (50 cm³)(0.10 M) = 2.5 moles
Therefore, the standard enthalpy of neutralization of sulphuric acid and sodium hydroxide is:
ΔH_neutralization = q_calorimeter / n_reactant = (28.624 J) / (2.5 moles) = -11.4496 kJ/mol
b. The value obtained in (a) is less than the expected value because heat exchange occurs between the reaction mixture and the calorimeter, which causes a loss of energy. Additionally, the solution may not have been perfectly insulated and heat may have been lost to the surroundings, also causing a loss of energy. Furthermore, the reaction may not have been performed under standard conditions, such as at a specific temperature or pressure.
A compound is found to contain 30.4% nitrogen and 69.6% oxygen. If it has a molecular mass of 92.0, what is its molecular formula?
Answer:
Molecular formula = N2O4
Explanation:
Step 1: Assume that the mass of a compound is 100%
Step 2: Calculate the number of moles of each element
Step 3: Represent an empirical formula
Step 4: Divide the number of moles of each element by the least number of moles
Step 5: Write the empirical formula
Step 6: Calculate the empirical mass
Step 7: Represent a molecular formula
Step 8: Solve for n by dividing molecular mass by empirical mass
Step 9: Multiply the subscripts of the empirical formula by the value of n to obtain the molecular formula
What do clouds and dew have in common?
They are both made of water vapor.
They are both forms of precipitation.
They both exist in Earth’s atmosphere.
They both form when water vapor condenses. I NEED HELP THIS IS MY FIRST TIME USING THIS BRAINLY THING PLEASE ANYONE HELP ME ON THIS ONE QUESTION
Cloud and dew both form when water vapor condenses. The last option.
What is condensation?Condensation is a phase-change process involving a change from the vapor phase to the liquid phase. It is the opposite of evaporation which involves a phase change from liquid to vapor.
Clouds are formed when microscopic water vapors present in the upper stratosphere condense to form visible water vapor or ice crystals. Dews, similarly, are formed when water vapors condense into visible liquids.
In other words, both clouds and dews are formed by the condensation of water vapors.
More on condensation can be found here: https://brainly.com/question/15563071
#SPJ1
A certain ore is 21.3% nickel by mass. How many kilograms of this ore would you need to dig up to have 20.0 g of nickel?
If a certain ore is 21.3% nickel by mass. The number of kilograms of this ore would you need to dig up to have 20.0 g of nickel is: 93.897 kg.
How to find the mass of ore?Using this formula to determine the mass of ore
Mass of ore = Mass of nickel / Percentage of nickel by mass
Convert the percentage to decimal form by dividing it by 100
0.213 = 21.3%.
So,
Mass of ore = (20.0 g) / (0.213)
Mass of ore = 93.897 kg
Therefore the mass of ore is 93.897 kg.
Learn more about mass of ore here:https://brainly.com/question/10306443
#SPJ1
What is equal to equivalent volume of hydrogen (NC)?
Calculate the equivalent weight of the metal if 0.28 L of
hydrogen (NC) was consumed to reduce 1.017 g of its oxide.
According to the question, Equivalent volume of any gas at STP is 22.4 litre. So, Equivalent volume of hydrogen, will be 22.4 litre. Equivalent wt. of metal= 0.025gm
What is the purpose of hydrogen?Hydrogen may be utilized to heat our dwellings and places of business in addition to powering vehicles and producing electricity. To reach net zero, it will be crucial to reduce our carbon emissions significantly.
Where can you find hydrogen?The majority of stars and the sun include it, and the planetary Jupiter is primarily made of it. Less than consistent with similar per million per volume is all that is found when it is a gas present in the air.
Equivalent wt. of metal/Weight of metal =moles of [tex]H_{2}[/tex] ×valency factor
Equivalent wt. of metal/ 1.017 g = (0.28 L/22.4 L) ×2
Equivalent wt. of metal= 0.025gm
To learn more about hydrogen visit:
https://brainly.com/question/4028968
#SPJ1
Make two molecules of water without any leftovers, what is the result?
To create molecules, atoms combine. Two hydrogen (H) atoms and one oxygen (O) atom make up a water molecule's three atoms. H2O is a common abbreviation for water because of this.
EXAMPLES OF MOLECULES AND WHAT A MOLECULE IS:The smallest unit of a material that keeps its content and characteristics is a molecule, which is made up of two or more atoms linked together by chemical bonds. The building blocks of chemistry are molecules.
What exactly are fundamental molecules?The phrase "the molecules of life" frequently refers to these four categories of molecules. Proteins, carbohydrates, lipids, and nucleic acids make up the four basic building blocks of life. Every single life on Earth depends on one or more of the four categories. These four molecules are necessary for a cell and an organism to exist.
To know more about molecules visit:
https://brainly.com/question/19922822
#SPJ1
Which labelled part is responsible for the ability of metals to be bent and shaped?
The majority of metals are malleable, meaning they can be bent and moulded without breaking.
define moulding ?
architect a shaped outline, especially one used on cornices, etc.
a formed strip of wood, stone, or other material
a moulded item, a decorative recessed or relieved surface, a decorative plane or curved strip for embellishment or finishing
The majority of metals are malleable, meaning they can be bent and moulded without breaking. This is due to the fact that they are made up of layers of ions that can glide over one another when the metal is twisted, hammered, or pushed. Most metals are ductile because the ions slide over one other and may be drawn/pulled into wires, making them excellent for electric cables.
To learn more about metals follow the given link: https://brainly.com/question/4135890
#SPJ1
MAKE NOTES ON METHOD OF MIXTURES ELECTRICAL METHOD.
The Method of Mixtures Electrical Method is a method used to determine the electrical conductivity of a material.
What is Electrical Method?The Electrical Method is a geophysical prospecting technique that uses electrical resistivity to map subsurface features, such as geological structures, fractures, and mineral deposits.
It involves measuring the amount of current that passes through a mixture of two materials under the application of a known voltage. The electrical conductivity of each material can then be determined by calculating the ratio of the current to the applied voltage. The electrical conductivity obtained from the Method of Mixtures Electrical Method can be used to characterize materials such as semiconductors and insulators.
To learn more about electrical conductivity
https://brainly.com/question/28869256
#SPJ1
Please help with the following problem attached!!
2.27x1022 molecules of CH4 contains 2.27x1022 moles of CH4 and 8.9x1022 moles of hydrogen atoms.
What is hydrogen atoms?Hydrogen atoms are the simplest atoms, consisting of a single proton and electron. They are the smallest and most abundant atoms in the universe, making up about 75% of all matter. Hydrogen atoms are also the most reactive elements, easily combining with other elements to form molecules, such as water. They are an essential part of many biochemical reactions, and are used in fuel cells to generate electricity. Hydrogen atoms are also important in astronomy, as they are a key component of stars and other cosmic bodies. Hydrogen atoms are also a major component of the Earth's atmosphere, making up about 20% of the air we breathe. In summary, hydrogen atoms are a vital part of the universe and are essential to life as we know it.
To learn more about hydrogen atoms
https://brainly.com/question/30282736
#SPJ1
HELP QUICK
This large tectonic plate is bounded on three sides by what's know as the Ring of Fire. What is the name of this tectonic plate?
Responses
A Indo- Australian Plate
B Eurasian Plate
C North American Plate
D Pacific Plate
Answer:
D
Explanation:
when adenosine diphosphate (adp) binds an additional phosphate group to create adenosine triphosphate (atp), this type of reaction is considered .
When adenosine diphosphate (ADP) binds an additional phosphate group to create adenosine triphosphate (ATP), this type of reaction is considered as Phosphorylation.
The terminal oxygen atom of the disphosphate group of ADP attacks the P atom of an inorganic phosphate in a process called phosphorylation. In the biological cell, ATPs are synthesized from ADP through (1) substrate level phosphorylation and (2) oxidative phosphorylation.
Substrate level phosphorylation, which occurs in glycolysis and the citric acid cycle, involves the direct phosphorylation of ADP. This process uses the free energy released from a coupled reaction. On the other hand, oxidative phosphorylation harvests the energy from the proton gradient of the mitochondria.
Learn more about Phosphorylation from the link given below.
https://brainly.com/question/11835776
#SPJ4
How mans, gram of HBr would exactly be
required to react with 2g of propyne ?
(Br=80,H=1, c=12) C3 H4+2HBr–> C3 H6 Br2
Answer:
The number of moles of HBr required to react with 2 g of propyne can be calculated by using the balanced chemical equation:
C3 H4 + 2HBr → C3 H6 Br2
The molar mass of propyne is (3 x 12 + 4 x 1) = 40 g/mol
So, 2 g of propyne is equal to 2/40 = 0.05 moles of propyne.
Since 2 moles of HBr are required to react with 1 mole of propyne, then 0.05 moles of propyne would require 0.05 x 2 = 0.1 moles of HBr.
Finally, to find the number of grams of HBr, we multiply the number of moles by its molar mass, which is (1 x 1 + 80 x 1) = 81 g/mol
So, 0.1 moles of HBr is equal to 0.1 x 81 = 8.1 g of HBr.
Can you help me with this question
After much experimentation, John discovers a law which says that the wavelengths of light absorbed by hydrogen gas fit into a pattern which he is able to express in a mathematical formula.
Niels has a hypothesis about why the wavelength of light absorbed by hydrogen has a certain value. Niels suggests the orbit of the electron in the hydrogen atom can only have certain radii, and when the electron "jumps" from one orbit to another, it emits light of an energy corresponding exactly to the difference in orbit energies.
About wavelengthIn physics, wavelength is defined as the distance traveled by a wave in one period. Wavelength is represented by the Greek letter lamda (λ). That's why the wavelength formula is often called the Lambda formula.
How to calculate the lambda formula depends on the type of wave. Based on the direction of propagation, waves are divided into two types, namely transverse waves and longitudinal waves.
Transverse waves are waves whose direction of propagation is perpendicular to the direction of vibration. Examples include water waves, string waves, and light waves. Meanwhile, longitudinal waves have a direction of propagation that is parallel to the direction of vibration, for example sound waves.
Learn more about wavelength at
https://brainly.com/question/13533093
#SPJ1
hydrogen and oxygen reacts chemically to form water. how much water would form if 14.8 grams of hydrogen reacted with 34.8 grams of oxygen
The mass of water that can be obtained is 2.2 g of water.
What is the mass of the water?We know that in the case that we have here, we are going to depend on the stoichiometry of the reaction and this is very important in the determination of the amount of the water that can be formed.
Now we can see that the reaction equation can be written from the fact that; [tex]2H_{2} (g) + O_{2} (g) ---- > 2H_{2} O(g)[/tex]. Then we can see that in this kind of chemical reaction we have to apply the stoichiometry.
Number of moles of the hydrogen = 14.8g/2 g/mol = 7.4 moles
Number of moles of oxygen = 34.8 g/32 g/mol = 1.1 moles
Given that 2 moles of hydrogen reacts with 1 mole of oxygen
7.4 moles of hydrogen reacts with 7.4 * 1/2
= 3.7 moles
Hence oxygen is the limiting reactant.
1 mole of oxygen produces 2 moles of water
1.1 moles of oxygen would produce 1.1 * 2/1
= 2.2 moles of water
Learn more about limiting reactant:https://brainly.com/question/14225536
#SPJ1
calculate the change in enthalpy for the chlorination of propane
A thermodynamic system's property called enthalpy is the result of adding the internal energy of the system and the product of its pressure and volume.
How is the change in enthalpy Illustrated?The change in enthalpy for a chemical reaction, also known as the heat of reaction or delta H, is the amount of heat absorbed or released during the reaction at a constant pressure. To calculate the change in enthalpy for the chlorination of propane, you would need to know the enthalpies of formation for the reactants and products, and use the following equation:
ΔH = ΣΔHf (products) - ΣΔHf (reactants)
Where ΔHf is the enthalpy of formation for a given substance.
Without knowing the specific conditions and reactants, it's not possible to give a exact delta H value for the chlorination of propane. But it's an exothermic process, meaning that heat is released during the reaction. The magnitude of the heat released will depend on the specific reactants and conditions used.
Note that an overview was given as the information is incomplete.
Learn more about enthalpy on:
https://brainly.com/question/14047927
#SPJ1
