Only technician A is correct because cylinder components are the most highly stressed parts of the diesel engine but cylinder pressures can NOT exceed 3000 pounds per square inch (psi) at this time.
What are the facts that prove the above?The findings of the nonlinear static analysis revealed that the high-stress area was situated in the crack start zone while the engine was operating at maximum power.
Peak cylinder pressures near TDC (where spark occurs) will be in the 300 psi range for light load engines, 1000 psi for full-power production engines, and 1500 psi or higher for race engines.
Learn more about Diesel Engines:
https://brainly.com/question/8829745
#SPJ1
If a microhydro dam generates 1 mw of power, how much energy will it produce annually?.
8.76 MUs of energy will be produced yearly by the micro-hydro dam.
What is a dam?A dam is a physical obstruction that slows or restricts the flow of subsurface or seawater. Dam-created reservoirs offer freshwater for uses.
Taking into account that the micro-hydro dam produces 1 MW of power
To estimate how much energy this will yearly generate.
There is one unit of electricity per kwh ( kW hours)
A 1000 KW plant becomes a 1 MW plant.
The quantity of toward the in a day when a plant runs continuously at maximum capacity is:
24000 Kwh, approximately 24000 units, is equal to 1000 KW multiplied by 24 hours. Units made during a specific year.
When 1000 KW is multiplied by 24 hours and 365 days, the result is 8,760,000 Kwh, or 8.76 Million Units (MUs).
The micro-hydro dam will generate 8.76 MUs of energy every year.
Learn more about dam, here:
https://brainly.com/question/29483452
#SPJ1
given an input clock signal at 10 mhz, what frequency would a[0] alternate? what frequency would a[1] alternate?
To make a counter, D Flip-Flops and adders will be used. A 4-bit
What frequency would a[0] alternate at given an input clock signal of 10 mhz? a[1] would alternate at what frequency?
Applying foam is another component of the overall foam strategy that, if not done correctly, can result in injury and property loss. So far, we've talked about creating a foam setup with the right nozzles, appliances, and hoselays.
We've talked about concentrate types and application rates, as well as expansion ratios and foam drain time. Now it's time to apply the finished foam to the spill or fire.
We've said it before in this series, and it's so important that we'll say it again. As with any potential fire, we should always supply the bare minimum of finished foam.
to learn more about D Flip-Flops And Adders refer to:https://brainly.in/textbook-solutions/q-elucidate-formation-n-type-extrinsic-semiconductors-1
#SPJ4
how does a typical stream vary along its longitudinal profile (variation of elevation along length)? what is a base level?
The grade or slope of a stream is known as the stream gradient (or stream slope), and it is determined by the ratio of elevation change to horizontal distance. The base level of the stream is the threshold below which erosion of the soil is prohibited.
How long are most streams on average?The longitudinal profile identifies average stream slopes and the depths of riffles, pools, runs, glides, rapids, and steps. For developing ratios, the normalization parameter is the average water surface slope, which is necessary for defining stream kinds.The grade or slope of a stream is known as the stream gradient (or stream slope), and it is determined by the ratio of elevation change to horizontal distance. This ratio is typically stated in meters per kilometer or feet per mile.When a stream abruptly changes gradient by emptying into a lake, an ocean basin, or a flat-floored basin, the stream's velocity will drop, causing sediment that can no longer be transported to be deposited there.To learn more about Stream gradient refer to:
https://brainly.com/question/1243042
#SPJ4
during this period, which value best approximates the average value of the san lorenzo river's discharge in cubic feet per second (cfs)?
The total annual discharge of the San Lorenzo River, as recorded at the stream gage near Felton, was almost 400 cubic feet per second (cfs).
ExplanationJust before the Boardwalk, the San Lorenzo River flows through the center of Santa Cruz to the Monterey Bay. Along the river in the Boardwalk and downtown regions is the San Lorenzo Riverway Trail. San Lorenzo Park is located on the northern edge of city, close to the river. In the past, logs from the Santa Cruz Mountains were transported by the river. (To the headwaters of the San Lorenzo River from Felton through a flume.) Over time, the river has receded due to increased water demand. The water moves at a rate of roughly 10 cubic feet per second in the summer. On December 23, 1955, a maximum discharge of 30,400 cubic feet per second was recorded. The Army Corps of Engineers built the current levees by 1959. They
To learn more about lorenzo river's refer to
https://brainly.com/question/25060766
#SPJ4
Gantt Charts are used to:
A. Show relationships between activities
B. Show the overall length of the project and each activity
C. Show float
D. Describe the WBS
Gantt Charts are used to show the overall length of the project and each activity.
What is gantt chart ?A Gantt chart is a sort of bar chart that shows a project timetable. It was created by Henry Gantt, who popularized the format between the years of 1910 and 1915. The dependence structures between activities and the state of the current schedule are also displayed in modern Gantt charts.
A Gantt chart is a project management tool that helps with the planning and scheduling of projects of all kinds. They are especially helpful for streamlining complex projects, though.
Thus, option B is correct.
To learn more about gantt chart, follow the link;
https://brainly.com/question/9980492
#SPJ1
the model that resembles a systems approach with inputs at the base, processes in the center, and outputs at the top is known as the:
The model that resembles a systems approach with inputs at the base, processes in the center, and outputs at the top is known as the team Leadership Model.
What Is a Leadership Model?A leadership model is a conceptual framework for the most effective personnel management.It often offers a commensurate, effective way of responding to organizational and employee demands. Interviews, discussion, openness to viewpoints from the public and private sectors, and individuals from all levels of an institution's structure are all components of a systems approach. A leader's method for giving instructions, carrying out strategies, and inspiring people is referred to as their leadership style.There are three primary leadership styles, according to study conducted in 1939 by psychologist Kurt Lewin and his team: authoritarian (autocratic), participative (democratic), and delegative (Laissez-Faire).To learn more about systems approach refer
https://brainly.com/question/13149592
#SPJ4
which would be best choice to secure a large gear (5-ft diameter) to the input shaft on a large stamping press ?
The three varieties of power transfer from a shaft to a nearby shaft are as follows.
clutch, gear drive, and belt drive
direct coupling, gear drive, and clutch
Brakes. The friction brakes used to stop or hold a slide movement must be intrinsically self-engaging, meaning they need power or force from an outside source to disengage. The slide's brake capacity must be high enough to hold the slide gear drive and its attachments at any point during travel and be powerful enough to immediately halt the slide's motion.When removing, deactivating, or energizing the external clutch engaging means, the clutch must release and the brake must be engaged.
Learn more about gear drive here:
https://brainly.com/question/25351775
#SPJ4
Which of the following methods is used to notify a provider of the denial of a claim by an insurance carrier?
A. Remittance advice
B. Coordination of benefits
C. Eligibility for insurance
D. CMS-1500 claim form
Answer:
A:Remittance advice
Explanation:
A five star hotel has a very high grand ceiling with intricate carvings on it. As people enter the hotel and look at the ceiling, they see a huge chandelier whose lights enhance the carvings on the ceiling. Which structural element is preventing the chandelier from causing cracks on the roof?.
The plate structural element is preventing the chandelier from causing cracks on the roof.
Structure elements of buildings refer to those elements which provide certain support to the design and survival of the building. Plate structural element is one such element that is used in construction.
Based on the given scenario in the statement, where a five-star hotel is designed with a very high grand ceiling with intricate carvings. Upon entering the hotel, people look at the ceiling and find huge chandelier lights enhancing the carvings on the ceiling. The plate structural element is used on the ceiling that prevents the chandelier from causing cracks on the roof.
You can learn more about structural elements at
https://brainly.com/question/26901483
#SPJ4
assume the skin friction drag on the airfoil is essentially that for a flat plate with the boundary layer being laminar and incompressible. what percentage of the total drag is due to skin friction?
Preliminary studies found that skin friction drag accounts for between 20 to 40% of overall drag.
Explain about the skin friction?Aerodynamic drag, which is a resistive force applied to an object moving in a fluid, includes skin friction drag.
The viscosity of a fluid as it passes across a surface is what creates skin friction. Its size is determined by the fluid's viscosity, the amount of wetted (or total) surface area in contact with it, and the degree of roughness of the surface.
Skin friction is important because it plays a role in the erosion of sediment particles from the water-bed boundary condition. Regarding the vertical mixing of the sediment over the water depth, form drag-related turbulence (separation-induced eddies, etc.) is significant.
To learn more about skin friction refer to:
https://brainly.com/question/14174373
#SPJ4
technician a says that a vehicle with a modified suspension may need an aftermarket kit installed to achieve the specified alignment settings. technician b says that the radar cruise control may have to be recalibrated if aligning a vehicle equipped with an electronic suspension. which technician is correct?
Both technician A and technician B are correct.
Some vehicles may require the installation of aftermarket kit alignments when the suspension is modified. This helps to properly adjust the alignment settings. Therefore, technician A is correct who states that in order to achieve the specified alignment settings, a vehicle with a modified suspension may need an aftermarket kit installed.
Alignment of vehicles done through an electronic suspension may need that recalibrated radar cruise control. Thus, technician B is also correct who says that in the alignment of a vehicle equipped with an electronic suspension, the radar cruise control may have to be recalibrated.
You can learn more about vehicle alignment at
https://brainly.com/question/16857448
#SPJ4
what material property would still cause strain in a strain gauge that is positioned perpendiclator to the direction of force if it were fully bonded in a high strain region of the sepcimen if this occurs then the set up must be calculated as a two active gauge set up will this set up continue to compensate for the environemental factor
Ductility is the material property would still cause strain in a strain gauge that is positioned. Understanding how an object responds to different forces is necessary for mechanical testing and measurement.
A material's ductility refers to its capacity to withstand plastic deformation or drawing without breaking. As a result, it provides information on how "soft" or pliable the material is. The types and concentrations of alloying elements present affect the ductility of steels in different ways. A material is said to be malleable if it is easy to hammer out a thin sheet of the material. The most malleable metal is gold. The ability of a solid material to deform when subjected to tensile stress is known as ductility.
Learn more about mechanical here-
https://brainly.com/question/20434227
#SPJ4
The voltage difference in a graphing calculator is 6V and the resistance is 1200 what is the current through the batteries of the graphing calculator?
The current through the batteries of the graphing calculator is 0.005 A
How to calculate current through the batteries of the graphing calculator?The potential difference in charge between two sites in an electrical field is quantified as voltage, also known as electromotive force.
When charged electrons (current) are forced through a conducting loop by the pressure of an electrical circuit's power source, they can perform tasks like lighting a lamp. In a nutshell, voltage is measured in volts and equals pressure.
The derived unit for electric potential, voltage, and electromotive force is the volt (symbol: V). The Italian physicist Alessandro Volta (1745–1827), who created the voltaic pile, conceivably the first chemical battery, is honored by having his name attached to the volt.
Given ,
I = ?
V = 6V
R = 1,200 Ω
I = 6V / 1,200 Ω
I = 0.005 A
To learn more about voltage refer to:
https://brainly.com/question/1176850
#SPJ1
) for laminar flow in a round 10-cm-diameter pipe, at what distance from the centerline (in cm) is the actual velocity equal to the average velocity?
When the acceleration is zero or the speed is constant, instantaneous and average velocities can both be equal. This is because all instantaneous velocities will be equal in this situation.
Explain about the Actual velocity?After the control filter and display filter have been applied, the filtered value that remains is known as the Actual Velocity. The Actual Velocity (Unfiltered) status register provides the unfiltered value, and the Actual Velocity (Control) value provides the first filtered value.
To calculate the velocity, multiply the distance travelled by the time needed to traverse that distance, then add direction. If one's position doesn't change, their velocity is zero.
Velocity is essentially a vector quantity. It is the rate of change in distance. The displacement change rate is the issue. A moving object can never move more slowly than it is moving. An object in motion can move at zero velocity.
To learn more about Actual velocity refer to:
https://brainly.com/question/24445340
#SPJ4
when an enclosed secondary stairwell is used for evacuating occupants, what should be located at the bottom floor to pressurize the stairwell and keep smoke from entering it?
Trench cuts are made to allow gases to expand and vent vertically, keeping them from reaching a specific line inside a building.
Trench cuts are made to allow gases to expand and vent vertically, keeping them from reaching a specific line inside a building. Hose lines should be set up underneath a correctly placed trench cut to prevent the spread of fire.
The conventional technique for mechanical horizontal ventilation uses smoke ejectors to create negative pressure. These particular fans create a negative pressure inside the building in order to suck the smoke, heat, and hot gases out of the structure through windows and openings.
When a layer of warm air (a Stratus) gathers at the roof level, smoke stratification happens. When smoke from a low-energy fire reaches this thermal barrier, it runs out of energy to continue rising.
To know more about gases click here:
https://brainly.com/question/1369730
#SPJ4
concrete must be compacted in the forms to eliminate trapped air and to fill completely around the reinforcing steel and into all the corners of the formwork. what tool is used to accomplish this?
A vibrat0r is a tool used to accomplish this.
A vibrat0r is a concrete tool that generates stronger concrete by strenuously shaking the concrete right after it is poured to eliminate the air pockets or air bubbles. The vibrat0r forces the trapped air out of the mixture making the final product a level slab and more compact.
According to the given context where concrete is compacted in the form in order to eliminate trapped air and fill around the reinforcing steel and into all of the corners of the framework. The tool named vibrat0r can be used to serve the purpose.
You can leran more about concrete at
https://brainly.com/question/25500184
#SPJ4
Motor oil has different ratings depending on how readily it flows. This property depends on how much attraction is present between its particles. Which property of a liquid does this illustrate?.
The viscosity of a liquid is a characteristic that does demonstrate the attraction between its particles.
What is viscosity ?The resistance of a fluid to deformation at a specific rate is measured by its viscosity. It is equivalent to the informal term "thickness" for liquids; syrup has a higher viscosity than water, for instance.The internal frictional force between neighbouring fluid layers that are moving relative to one another is measured by viscosity. A viscous fluid, for instance, flows more swiftly near a tube's axis than it does near its walls when the fluid is driven through the tube.The state of a fluid, including its temperature, pressure, and rate of deformation, affects its viscosity. In some circumstances, the dependence on some of these traits is minimal.Various viscometer and rheometer types are used to measure viscosity. When a fluid cannot be described by a single viscosity value and more parameters need to be set and measured than in the case of a viscometer, a rheometer is used.To learn more about viscosity refer :
https://brainly.com/question/2684299
#SPJ4
in what applications would it be beneficial to use each amplifier? (i.e., when would you use a voltage-follower, inverting, and non-inverting amplifiers?)
A signal's voltage, current, or power can be increased by an electronic device called an amplifier.
What is an Inverting Amplifier?An inverting operational amplifier (or Op-Amp) is one that is built to generate an output signal that is 180 degrees out of phase with the applied input signal.As a result, in the case of an inverting amplifier, the amplified output signal will have a negative phase if the input signal is positive, and vice versa. The simplest and most popular operational amplifier configuration is the one that inverts signals.The usual inverting amplifier circuit. It is evident from this circuit that a feedback signal is supplied in the operational amplifier in order for the circuit to operate in a closed loop. Additionally, it should be noted that the feedback is negative, which improves the circuit's accuracy of operation.The following expression gives the inverting amplifier's closed loop gain
Av = Vout/Vin = −R2 /R1
Where R1 is the resistance between the source and the input terminal and R2 is the feedback resistance.Applications for inverting amplifiers include phase shifters, integration, signal balancing, mixer circuits, etc.To Learn more About amplifier Refer To:
https://brainly.com/question/28996974
#SPJ4
a transformer is connected as a step-up transformer with a 15:1 turns ratio. if the primary voltage is 30 v, what is the voltage of the secondary?
The correct answer is the secondary voltage will be 120*5 = 600V transformer.
A transformer is an electrical apparatus that manipulates the level of voltage flowing through any point in a power grid. In a distribution system, the transformer decreases the voltage traveling through power lines to a level more suitable for residential and commercial use.An electrical device that can change the A.C. current is known as a transformer. Principle – A transformer works on the principle of mutual induction. Mutual induction is the phenomenon by which when the amount of magnetic flux linked with a coil changes, an E.M.F. is induced in the neighboring coil.
To learn more about transformer click the link below:
brainly.com/question/15200241
#SPJ4
50 POINTS
What characterizes great interior design? (Select all that apply.)
What are the philological elements of interior design most like?
An interior designer, Cal, gets a job to help restore the interior of an old hotel that its new owner wants returned as much as possible to its original state. The hotel, built two centuries ago, has gone through a lot of changes and served many purposes, but now it’s going back to its original function, and the owner wants to restore as many of the original details as possible. In many cases, this involves replacing custom features such as ornate finials, and in many other cases new wood must precisely match the type, color, and texture of surviving original wood. What research methods do you predict Cal will need to use for this project? (Select all that apply.)
The research methods that Cal will need to use for this project are as follows:
Cal will need to do extensive archival research in order to find out as much information concerning the hotel's original interior as possible. Cal will need to do all internet research he can to find out anything online he can about the hotel's history.Thus, the correct options for this question are B and D.
What do you mean by Research methods?Research methods may be defined as the strategy that one should utilize in order to do research and determine some facts with respect to evidence.
In order to make the research more accurate and satisfactory, Cal will follow two types of research methods that will meet the original requirement. These are the archival research method and the internet research method.
Therefore, the correct options for this question are B and D.
To learn more about Research methods, refer to the link:
https://brainly.com/question/12325082
#SPJ1
briefly cite the differences between the recovery and recrystallization processes. explain the differences in grain structure for a metal that has been cold worked and one that has been cold worked and then recrystallized
While primary recrystallization proceeds discontinuously by the formation, recovery describes the gradual re-ordering and destruction of the stored dislocations.
High-angle grain boundaries that sweep the deformation substructure infrequently. After cold plastic deformation and/or during hot working, RECOVERY, RECRYSTALLIZATION, AND GRAIN GROWTH are microstructural changes that take place during annealing. Because they return the microstructural configuration to a lower energy level, these three mechanisms are commonly referred to as restoration processes. Recovery is crucial for removing internal stresses from forged, welded, and manufactured equipment without reducing the strength developed during and after use. The most crucial technique for cleaning nonvolatile organic materials is recrystallization. The process of recrystallization requires dissolving the solute, which needs to be purified, in a suitable hot solvent.
Learn more about stresses here-
https://brainly.com/question/17252580
#SPJ4
wt steel shape is produced by cutting a wide flange beam lengthwise in half. group of answer choices true false
It is true that wt steel shape is produced by cutting a wide flange beam lengthwise in half.
A beam is a structural component that resists loads mostly applied laterally to its axis (an element designed to carry primarily axial load would be a strut or column). Its primary method of deflection is bending. Reaction forces are produced at the beam's support points as a result of the loads placed on it.
As a result of all the forces operating on the beam, internal stresses, strains, and deflections of the beam are caused by shear forces and bending moments within the beams. Beams differ from one another in terms of how they are supported, their profile (the form of their cross-section), equilibrium circumstances, length, and material.
Beams are typically used to describe structural elements in buildings or civil engineering when the beams are horizontal and support vertical loads.
To know more about beam click here:
https://brainly.com/question/23818966
#SPJ4
technician a says that electrons in a fuel cell flow from the cathode to the anode. technician b says that electrons in a fuel cell flow from the anode to the cathode. which technician is correct?
According to technician b, in a fuel cell, electrons move from the anode to the cathode. is accurate in its assertion.
What is anode and cathode?At the anode, there is an oxidation reaction. This electrode would accumulate electrons as the oxidized species would lose electrons. As a result, the anode is negatively charged. In contrast to the cathode, the reduced species would get electrons in the reduction response. As a result, the electrode, or cathode, is positively charged because it is electron-free.Oxidation and reduction always take place at the anode and cathode, respectively. (Vowels go with other vowels; consonants go with other consonants.)Therefore, regardless of the type of cell you are dealing with, the chemicals that are oxidized send the electrons onto the external circuit at the anode, where they then move through the circuit from the anode to the cathode, where they are picked up by the chemicals that are being reduced.To learn more about anode and cathode refer to:
https://brainly.com/question/20078178
#SPJ4
which of the following is not a performance technique developed by stanislavski? multiple choice through line biomechanics concentration and observation magic if
Through line biomechanics concentration and observation magic if International Society of Biomechanics in sports.
What is "International Society of Biomechanics in sports"?The recently developed professional association in biomechanics is the "International Society of Biomechanics in sports".It is the professional association in bio-mechanics.
It is an international society which is dedicated to bio-mechanics to sports. The main purpose of the society is to understand and study the human movement and its relation to sport bio-mechanics. They provide information regarding bio-mechanics in sports.
Therefore, Through line biomechanics concentration and observation magic if International Society of Biomechanics in sports.
Learn more about biomechanics on:
https://brainly.com/question/13898117
#SPJ1
A vehicle can hydroplane in speeds as low as __ mph.
Answer:35
Explanation:
The reverse leakage current of a transistor when connected to CB configuration is 0.2A and it is 18A when the transistor is connected in CE configuration. Calculate α DC and β of the transistor. 1B=13A
Answer:
0.988 and 89
Explanation:
when conduit is not used in new residential low-voltage construction, cables can be pulled through the finished wall by the use of a . select one: a. mud ring b. closed box c. sleeve d. ceramic tube
the correct answer is option (d) ceramic tube.
A ceramic tube is most commonly used in industrial high temperature applications, and electrical and thermal insulations. Our high temperature ceramic tubes include alumina, silicon carbide, and quartz choices that have excellent thermal, anti-shock, anticorrosion, and extreme high temperature resistance properties. The uniform dimensional stability of ceramic tubing offers optimal insulation while providing reliable protection.
To learn more about ceramic tube click on link given below:
brainly.com/question/20466176
a 3105 aluminum plate previously cold worked 23% is 2-in thick. it is then cold worked further to 1.4 in. calculate the final elongation.
Answer:
Explanation:
x
the hydraulic gradient is: group of answer choices the permeability of the rock. the slope of the water table. the increase in temperature with depth. the rate of flow of groundwater.
Groundwater moves in the direction of maximum decreasing total head under the influence of the hydraulic gradient.
Explain about the hydraulic gradient?The change in water level per unit of distance along the direction of highest head drop is known as the hydraulic gradient (1), which is the slope of the water table or potentiometric surface.
If the gradient is negative, which means the hydraulic head is lower at depth, there is an indication of a downward flow component. The hydraulic head is higher at depth if the gradient is positive, on the other hand, which denotes an upward flow component. The gradient's size tells us a lot about its importance.
This vector depicts the flow direction of groundwater, with zero denoting "no flow" and negative values denoting flow along a dimension.
To learn more about hydraulic gradient refer to:
https://brainly.com/question/15872139
#SPJ4
technician a says that in the event of a total failure of the primary circuit in an fmvss-121 compliant tractor-trailer combination, the rig is designed to be brought safely to a complete stop. technician b says that in the event of a total failure of the primary circuit the relay section of the treadle valve will be actuated mechanically. who is correct?
A technician is a worker in the technology industry who possesses the necessary knowledge, abilities, and skills as well as a practical comprehension of the theoretical underpinnings.
Who is technician?Expert technicians in a certain tool domain often have expert competency in technique and a moderate comprehension of theory.
As a result, technicians in that sector of technology are typically significantly more knowledgeable about technique than the average layperson and even general professionals.
For instance, although not as knowledgeable in acoustics as acoustical engineers, audio technicians are more adept at using sound equipment and are likely to know more about acoustics than other studio staff members, such as performers.
Therefore, A technician is a worker in the technology industry who possesses the necessary knowledge, abilities, and skills as well as a practical comprehension of the theoretical underpinnings.
To learn more about technician, refer to the link:
https://brainly.com/question/14290207
#SPJ1
