The correct answer is (b) NH3(g) → 1/2N2(g) + 3/2H2(g). The heat of reaction for this equation is equal to the average bond energy for the N-H bond in NH3.
The heat of reaction (ΔH) for a chemical reaction is the difference in enthalpy between the products and reactants. In the case of a reaction involving the breaking of a bond, the ΔH can be related to the bond energy of that bond. The average bond energy for the N-H bond in NH3 is approximately 391 kJ/mol.
In equation (b), one N-H bond is broken in NH3 to form 1/2 N2 and 3/2 H2. The ΔH for this reaction is equal to the bond energy of the N-H bond, which is 391 kJ/mol. Therefore, the correct answer is (b).
Learn more about bond energy here;
https://brainly.com/question/26141360
#SPJ11
Which of the following is a strong base? Select the correct answer below: O Nitrite ion O Sulfate ion O Cyanide ion Calcium hydroxide
Because its conjugate acid is weaker than other conjugate acids, the cyanide ion is a strong base.
C is the correct answer.
The cyanide ion is a good nucleophile as well. Therefore, depending on the solvent and alkyl group, a mixture of products must form in the reaction of alkyl halides with KCN.
Strong bases are those that are entirely dissociated in water. One or more hydroxide ions (OH-) are produced per base molecule when these chemicals ionise in water. In contrast, a weak base in water only partially splits into its ions.
A strong base is a substance with the capacity to eliminate a proton from a very weak acid. Or, when submerged in water, they totally separate into its ions. Sodium hydroxide and potassium hydroxide are two examples.
Learn more about Strong base:
https://brainly.com/question/27089588
#SPJ4
The complete question is:
Which of the following is a strong base? Select the correct answer below: A. Nitrite ion
B. Sulfate ion
C. Cyanide ion
D. Calcium hydroxide
When 0. 105 mol propane, c3h8 is burned in an excess of oxygen, how many moles of oxygen are consumed? the products are carbon dioxide and water. You have to properly balance the equation before you can answer this question.
Therefore, 0.525 moles of oxygen are required to react with 0.105 moles of propane.
The balanced equation for the combustion of propane is:
C3H8 + 5O2 -> 3CO2 + 4H2O
From this equation, we can see that 1 mole of propane reacts with 5 moles of oxygen to produce 3 moles of carbon dioxide and 4 moles of water.
Since we have 0.105 mol of propane, we need to determine how many moles of oxygen are required to react with it. Using the mole ratio from the balanced equation, we can set up a proportion:
0.105 mol C3H8 / 1 x (5 mol O2 / 1 mol C3H8) = 0.525 mol O2
To know more about moles,
https://brainly.com/question/21220673
#SPJ11
did you get a pure product? please report all of your experimental data (melting point, ir peaks, and tlc spots/rf) as the basis for rationalizing your conclusion. if you did not get a pure product, what was the impurity?
Based on the experimental data, it is unclear whether a pure product was obtained. It is not possible to determine purity of a compound without knowing the expected melting point, IR peaks, and TLC spots/Rf values of the compound.
The purity of the product cannot be determined without knowing the expected melting point, IR peaks, and TLC spots/Rf values of the compound. If the experimental values match the expected values, then a pure product was obtained. If there are deviations in the experimental data, it may indicate the presence of impurities.
For example, a lower melting point than expected could indicate the presence of an impurity with a lower melting point. Similarly, additional peaks in the IR spectrum could suggest the presence of impurities. The TLC spot and Rf values can also help identify impurities.
If there are additional spots or if the Rf values are significantly different than expected, then there may be impurities present in the product. Further analysis, such as purification methods or additional characterization techniques, may be necessary to confirm the purity of the product.
Learn more about impurities here:
https://brainly.com/question/30630528
#SPJ11
Explain why you think monitoring of the reaction by TLC is better than the oxidation reaction? (reduction lab)
TLC is a more efficient method for monitoring the oxidation reaction than the oxidation reaction itself because it allows for a quicker and more precise measurement of the reaction's progress.
What is reaction?Reaction is the way in which a person, group, or thing responds to a stimulus or event. It can be physical, psychological or emotional. Reactions can be conscious or unconscious, voluntary or involuntary, and they can occur in response to a variety of stimuli, such as a touch, a sound, or a sight. Reactions can be short-lived or long-term, depending on the nature of the stimulus.
TLC also allows for a more precise identification of the reaction components, since the chromatogram can be compared to a reference to determine which components are present. Additionally, TLC can be used to measure the reaction rate, since the chromatogram can be used to track the concentration of the components over time. This provides a more accurate measure of the rate of the reaction than the oxidation reaction itself.
To learn more about reaction
https://brainly.com/question/25769000
#SPJ4
what volume of dry carbon dioxide, measured at 25 degrees celsius and 785 mm hg, will result from the combustion of 2.50 g of pentane? the vapor pressure of water at 25 degrees celsius is 23.7 torr.
The volume of dry carbon dioxide is 55mL measured at 25 degrees Celsius and 785 mm hg, will result from the combustion of 2.50 g of pentane.
Carbon dioxide may be found in solid form as dry ice. Since CO2 does not have a liquid state at normal atmospheric pressure and instead sublimates directly from the solid state to the gas state, it is frequently used for short-term refrigeration. In addition to being utilised in fog machines in theatres for dramatic effects, it is largely employed as a cooling agent.
Its benefits include being colder than water ice and leaving no traces behind (apart from accidental frost from atmospheric moisture). It is helpful for keeping frozen items (like ice cream) from spoiling in situations when mechanical chilling is not possible.
At Earth's atmospheric pressure, dry ice sublimates at 194.7 K (78.5 °C; 109.2 °F). The solid is hazardous to handle without protection against frostbite injuries because to the intense cold. While typically not very toxic, the buildup in confined spaces can make the outgassing from it hypercapnic (abnormally elevated blood carbon dioxide levels).
Learn more about Dry carbon dioxide:
https://brainly.com/question/12062493
#SPJ4
the structural formula of urea is shown. h n o h c n h h predict the electron domain and molecular geometries at the nitrogen and carbon atoms, applying the vsepr theory. electron domain geometry molecular geometry nitrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . carbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . trigonal planar
The electron domain and molecular geometries at the nitrogen and carbon atoms of urea can be predicted by applying the VSEPR theory.
In urea, the nitrogen atom has two bonded electron domains (one from the double bond with carbon and one from the lone pair of electrons) and the carbon atom has three bonded electron domains (one from the double bond with nitrogen and two from the two single bonds with oxygen).
Based on the VSEPR theory, the electron domains around the nitrogen atom will be arranged in a tetrahedral shape. However, since one of the domains is a lone pair, the molecular geometry around the nitrogen atom will be bent or angular.
On the other hand, the electron domains around the carbon atom will be arranged in a trigonal planar shape. Therefore, the molecular geometry around the carbon atom will also be trigonal planar.
To summarize, the electron domain geometry around nitrogen in urea is tetrahedral and the molecular geometry is bent or angular. The electron domain geometry around carbon is trigonal planar and the molecular geometry is also trigonal planar.
To know more about VSEPR theory, visit:
https://brainly.com/question/14992767
#SPJ11
draw a “a parallel circuit “that includes two batteries, 1 closed switch , a resistor, 4 bulbs
Make cross like structure inside the circle others are same
consider ne, n2, xe, and ch4 gases at the same temperature and pressure. which gas would behave most ideally?
The gas that would behave most ideally among Ne, N2, Xe, and CH4 at the same temperature and pressure is Neon.
This is because Ne is a noble gas with the least intermolecular forces and minimal electron interactions, which are key factors for a gas to exhibit ideal behavior.
The ideal gas law states that at the same temperature and pressure, all gases should behave similarly. However, in reality, most gases deviate from ideal behavior to some extent. This is because ideal gas behavior assumes that there are no intermolecular forces between gas molecules, which is not the case in real gases.
Noble gases, such as neon and argon, have a completely filled valence shell and are therefore considered to be non-polar. This means that they have weaker intermolecular forces than other gases, such as CH4 or N2, which are polar. Therefore, noble gases are more likely to behave ideally than other gases under the same conditions.
In summary, while all gases should behave similarly at the same temperature and pressure according to the ideal gas law, noble gases like neon and argon would behave most ideally due to their weaker intermolecular forces.
To know more about Neon, visit:
https://brainly.com/question/24481291
#SPJ11
The protonated intermediate ________ leading to nitronium ion formation
The protonated intermediate "nitric acid" is involved in the nitration of aromatic compounds, leading to nitronium ion formation.
What is Protonated?
Protonation is a chemical process in which a hydrogen ion (H+) is added to a molecule or ion, forming a species with a net positive charge. The resulting species is called a protonated species or a conjugate acid. Protonation is an important process in many chemical reactions, particularly in acid-base reactions.
When nitric acid dissolves in water, it undergoes autoionization to form nitronium ion and a hydronium ion:
[tex]HNO_{3}[/tex] + [tex]H_{2} O[/tex] ⇌ [tex]N O_{2}[/tex]+ + [tex]H_{3} O[/tex]+
The formation of nitronium ion from nitric acid occurs via the protonation of the nitrogen atom in the nitrate group by a hydronium ion, followed by the loss of a water molecule. This protonated intermediate is highly reactive and can participate in various nitration reactions, such as the nitration of aromatic compounds.
Learn more about Protonated from the given link
https://brainly.com/question/15215343
#SPJ4
The amount of air that is moved between the atmosphere and alveoli in 1 minute is.
The amount of air that is moved between the atmosphere and alveoli in 1 minute is alveolar ventilation, option B.
Alveolar ventilation is the process by which the alveoli and the surrounding environment exchange gases. It is a procedure that allows oxygen to enter the lungs from the atmosphere and carbon dioxide that was brought into the lungs by mixed venous blood to be expelled from the body. Alveolar ventilation is typically defined as the amount of fresh air that enters the alveoli each minute. However, this definition also includes the amount of alveolar air that leaves the body each minute.
With each inspiration, 350 mL of fresh air containing approximately 21% oxygen enters the 3 L of gas already present in the lungs, and with each exhalation, 350 mL of fresh air containing approximately 5% to 6% carbon dioxide exits the lungs. The alveolar air diffuses approximately 300 milliliters of oxygen into the pulmonary capillary blood per minute, and the pulmonary capillary blood diffuses approximately 250 milliliters of carbon dioxide into the alveoli per minute.
Learn more about Alveolar ventilation:
https://brainly.com/question/31360805
#SPJ4
Complete question:
The amount of air that is moved between the atmosphere and alveoli in 1 minute is Multiple Choice
pulmonary ventilation.
alveolar ventilation.
internal respiration.
airflow.
external respiration.
What are the 5 conditions required for Hardy-Weinberg equilibrium?
The Hardy-Weinberg equilibrium is a theoretical concept in population genetics that describes a stable and unchanging frequency of alleles in a population over time. The following five conditions must be met for the Hardy-Weinberg equilibrium to hold true:
1. No mutation: The allele frequencies in the population must not change due to mutations.
2. No migration: The population must be isolated and not receive new individuals from other populations.
3. No natural selection: The environment must not favor one genotype over another, and all genotypes must have equal fitness.
4. Random mating: Mating between individuals must be completely random, with no preference for specific genotypes or phenotypes.
5. Large population: The population must be large enough that chance events, such as genetic drift, do not significantly alter the allele frequencies.
If these conditions are met, the frequencies of alleles and genotypes in the population will remain constant from one generation to the next, and the population will be in Hardy-Weinberg equilibrium.
To know more about mutation please visit:
https://brainly.com/question/30696458
#SPJ11
list as high or low solute concentration- 0.5% & 2%
Solute-rich solution with a higher concentration are known high solute concentration, 0.5% lower solute fixation and 2% higher solute concentration.
0.5% = lower solute fixation and
2% = higher solute concentration
What is high and low solute fixation?The solution with the highest solute concentration is hypertonic, while the solution with the lowest solute concentration is hypotonic, when two solutions with different solute concentrations are compared. Isotonic solutions have the same concentration of the solute. In comparison to the second solution, the first sugar solution is hypotonic.
What is the concentration of the solute?At least two components make up an aqueous solution: the solute (the substance that dissolves in water) and the solvent (water). Most of the time, one wants to know how much solute is dissolved in the solution. We refer to these as concentrations.
Therefore, 0.5% = lower solute fixation and
2% = higher solute concentration.
Learn more about solute concentration :
brainly.com/question/28564792
#SPJ4
Explain the term secondary structure with reference to hydrogen bonding;
Secondary structure refers to the arrangement of the covalently bonded atoms in a protein or nucleic acid.
What is molecule?Moleculer is a microservice toolkit for Node.js. It is an open-source framework that enables developers to create, deploy and manage distributed systems in a fast and efficient way.
It is determined by the hydrogen bonding between the atoms, which results in the formation of specific three-dimensional shapes, such as the alpha helix, beta sheet, and loop structures. Hydrogen bonds form between the amide hydrogen atoms of the peptide backbone and carbonyl oxygen atoms of the peptide backbone, as well as between side chain atoms, such as the oxygen and nitrogen atoms of the amino acids. This hydrogen bonding helps to stabilize the secondary structure of the protein or nucleic acid, as the bonds create a lattice-like structure that holds the molecule together.
To learn more about molecule
https://brainly.com/question/475709
#SPJ4
WHAT IS THE LIQUID THAT IS POURED FROM THE VESSEL WITHOUT DISTURBING THE SOLID CALLED?
The liquid that is poured from the vessel without disturbing the solid is called the supernatant. It is the clear liquid layer that sits on top of the solid or sediment after it has settled due to gravity or centrifugation.
The supernatant is separated from the solid or sediment because it has a lower density than the solid or sediment. The process of separating the liquid from the solid or sediment is called decantation. Decantation is a simple separation technique used in various fields, such as chemistry, biology, and environmental science. It is commonly used to separate mixtures of immiscible liquids, such as oil and water, or a solid and liquid, such as sand and water. To perform decantation, the mixture is left undisturbed for a period of time, allowing the solid or sediment to settle to the bottom of the container. The liquid is then carefully poured off, leaving the solid or sediment behind.
To know more about liquid please visit:
https://brainly.com/question/31321462
#SPJ11
what would the potential of a standard hydrogen electrode (s.h.e.) be under the following conditions? [h ]
The potential of a standard hydrogen electrode (s.h.e.) would depend on the concentration of hydrogen ions ([H+]) in the solution.
The standard hydrogen electrode (s.h.e.) is used as a reference electrode to measure the potential of other half-cells. The potential of the s.h.e. is defined as zero volts when the concentration of hydrogen ions is 1 mol/L and the pressure of hydrogen gas is 1 atm at a specified temperature. However, if the concentration of hydrogen ions is not 1 mol/L, the potential of the s.h.e. will change accordingly. Specifically, the potential of the s.h.e. will increase as the concentration of hydrogen ions decreases (i.e. becomes more acidic) and decrease as the concentration of hydrogen ions increases (i.e. becomes more basic). Therefore, the potential of the s.h.e. under the given condition of [H+] would need to be specified to determine its value.
learn more about hydrogen electrode
https://brainly.com/question/24002834
#SPJ11
how do we construct the punett square of gibbs free energy?
A Punnett Square is a beneficial device that enables to expect the versions and chances that may come from activity. In a punnet square of Gibbs free energy, Delta S values are on top. Delta H is are on the side.
The power related to a chemical response that may be used to do work. The unfastened power of a device is the sum of its enthalpy (H) plus the made of the temperature (Kelvin) and the entropy (S) of the device. The extrade in Gibbs unfastened power (ΔG) is the most quantity of unfastened power to be had to do beneficial work. To construct the punnet square for Gibbs free energy, Delta S values are on top. Delta H is are on the side.
To learn more about Gibbs free energy check the link below-
brainly.com/question/9179942
#SPJ4
Which response has the following substances arranged in order of increasing boiling point? Ar, NaCIO3, H2O, H2Se A. Ar < H2O < H2Se < NaClO3 B. NaClO3 < H2Se < H2O < Ar C. NaClO3 < H2O < H2Se < Ar D. Ar < NaClO3 < H2Se < H2O E. Ar < H2Se < H2O < NaCIO3
The correct order of increasing boiling point is[tex]NaClO_{3}, H_{2}O, H_{2}Se, Ar[/tex]Option (C)
The boiling point of a substance depends on the strength of intermolecular forces between its particles. NaClO₃ is an ionic compound, so it has strong electrostatic forces between its ions, requiring a higher temperature to break the bonds and boil the substance.
Among the remaining three substances, H₂O has the strongest intermolecular forces due to hydrogen bonding, followed by H₂Se, which also exhibits hydrogen bonding but to a lesser extent. Ar is a noble gas and has only weak van der Waals forces between its atoms, so it has the lowest boiling point of the four substances.
Therefore, the correct order of increasing boiling point is[tex]NaClO_{3}, H_{2}O, H_{2}Se, Ar[/tex]
To learn about boiling point:
https://brainly.com/question/2153588
#SPJ4
how much nitrogen evaporates if it is at its boiling point of 77 k k and has a latent heat of vaporization of 200 kj/kg k j / k g
We cannot determine how much nitrogen evaporates at its boiling point of 77 k without additional information, such as the initial mass of the nitrogen.
The amount of nitrogen that evaporates at its boiling point depends on its initial mass and the latent heat of vaporization, which is the amount of heat needed to convert a unit mass of liquid into gas at constant temperature. The latent heat of vaporization of nitrogen is 200 kJ/kg.
Therefore, if we know the initial mass of the nitrogen, we can calculate how much nitrogen evaporates by multiplying the initial mass by the latent heat of vaporization.
For example, if we have 1 kg of nitrogen at its boiling point of 77 k, the amount of nitrogen that evaporates would be:
(1 kg) x (200 kJ/kg) = 200 kJ
This means that 200 kJ of energy is required to evaporate 1 kg of nitrogen at its boiling point.
To know more about nitrogen, visit:
https://brainly.com/question/16711904
#SPJ11
The [H+] of pure water at 30 °C is 1. 4x10-7. What is the pH of the solution?
The pH of the solution is 6.85 if the pure water at 30 °C has Hydrogen concentration ions [H+] [tex]1. 4*10^{-7}[/tex].
Temperature of water = 30 °C
concentration of H+ ions = [tex]1. 4*10^{-7}[/tex]
The pH value of any solution will be defined in the negative logarithm of hydrogen ions. But here we consider the (H+) value to calculate the pH value of the solution.
If the pH value of the solution is less than 7 will be considered Acids, equal to 7 is Neutral, and greater than 7 and below 14 will be considered Bases.
pH = -log[H+]
pH = -log([tex]1.4*10^{-7}[/tex])
pH = 6.85
Therefore, we can conclude that the pH of the solution is 6.85.
To learn more about pH value
https://brainly.com/question/28198391
#SPJ4
2. C) Br2 and Cl2 can react to form the compound BrCl. The boiling point of Br2 is 332 K, whereas the boiling point of BrCl is 278 K. Explain this difference in boiling point in terms of all the intermolecular forces present between molecules of each substance.
It can be explained by the presence of stronger intermolecular forces in BrCl, such as dipole-dipole interactions, compared to the weaker dispersion forces in [tex]Br_{2}[/tex] .
The difference in boiling points between [tex]Br_{2}[/tex] and BrCl can be explained by the intermolecular forces present between their molecules. [tex]Br_{2}[/tex] consists of nonpolar molecules held together by weak London dispersion forces, which are the result of temporary fluctuations in electron density.
In contrast, BrCl molecules have a polar covalent bond, creating permanent dipole-dipole interactions in addition to London dispersion forces. The presence of stronger dipole-dipole interactions in BrCl leads to increased intermolecular forces, requiring more energy to overcome and hence resulting in a lower boiling point compared to [tex]Br_{2}[/tex].
Learn more about boiling point, here:
https://brainly.com/question/2153588
#SPJ12
What compounds may be used to clean EXTRA-stubborn residues?
When it comes to cleaning extra-stubborn residues, there are several compounds that can be used. One of the most effective is a mixture of baking soda and vinegar.
This combination creates a chemical reaction that produces carbon dioxide, which helps to break down the residue. Another option is using a commercial cleaner that contains enzymes, which are capable of breaking down even the toughest residues. These cleaners can be found at most hardware stores and are particularly effective for removing stains from carpets and upholstery.
Another compound that can be used for extra-stubborn residues is hydrogen peroxide. It is a strong oxidizing agent that can break down organic materials and can be used to remove stains from clothing, carpets, and other surfaces. However, it is important to use caution when using hydrogen peroxide, as it can bleach fabrics and damage some surfaces.
Lastly, rubbing alcohol is a powerful solvent that can be used to break down and remove stubborn residues from hard surfaces. It is particularly effective for removing adhesive residue and can be used to clean surfaces like glass and metal. Overall, these compounds are all effective at removing extra-stubborn residues, but it is important to use them carefully and follow the manufacturer's instructions to avoid damaging the surfaces being cleaned.
learn more about compounds here
https://brainly.com/question/12166462
#SPJ11
Catalysts will ______________ activation energy of a reaction.
Catalysts will decrease the activation energy of a reaction. Catalysts are substances that can speed up chemical reactions by providing an alternate pathway with a lower activation energy.
They do not undergo any permanent changes during the reaction and can be used multiple times. The lower activation energy provided by a catalyst allows for more reactant molecules to have enough energy to overcome the energy barrier and convert into products.
This leads to a faster rate of reaction and can be particularly useful in industrial processes where time is a crucial factor. Catalysts are widely used in a variety of industries including petrochemical, pharmaceutical, and food production. By reducing the activation energy required for a reaction, catalysts can make processes more efficient, cost-effective, and sustainable.
To know more about chemical reaction visit:
https://brainly.com/question/29762834
#SPJ11
3. Acetylene gas, C2H2, is used in welding, produces an extremely hot flame when it burns in pure oxygen according to the following reaction. 2 C2H2(g) + 5O2(g) Ã 4CO2(g) + 2H2O(g) How many moles of water (H2O) are produced when 25.0 grams of C2H2 burns completely?
The number of moles of water (H₂O) produced when 25.0 grams of C₂H₂ burns completely is 0.463 moles.
To solve the problem, we need to use stoichiometry, which relates the amounts of reactants and products in a chemical reaction. The balanced equation for the combustion of acetylene (C₂H₂) is:
2 C₂H₂(g) + 5O₂(g) → 4CO₂(g) + 2H₂O(g)
From the equation, we see that 2 moles of C₂H₂ react with 2 moles of H₂O. Therefore, to determine the number of moles of H₂O produced from a given amount of C₂H₂, we can use the following calculation:
moles of H₂O = moles of C₂H₂ × (2 moles of H₂O / 2 moles of C₂H₂)
First, we need to convert the given mass of C₂H₂ to moles using its molar mass, which is:
2 × 12.01 g/mol (for the carbon atoms) + 2 × 1.01 g/mol (for the hydrogen atoms) = 26.04 g/mol
Therefore, 25.0 g of C₂H₂ is equal to:
25.0 g ÷ 26.04 g/mol = 0.961 mol C₂H₂
Substituting this value into the equation above, we get:
moles of H₂O = 0.961 mol C₂H₂ × (2 mol H₂O / 2 mol C₂H₂) = 0.463 mol H₂O
To know more about moles, refer here:
https://brainly.com/question/29367909#
#SPJ11
study this chemical reaction: feso4(aq) mg(s)(s)(aq) then, write balanced half-reactions describing the oxidation and reduction that happen in this reaction.
The oxidation half-reaction is [tex]2 Mg(s) - > 2 Mg^2^+(aq) + 4e^-[/tex], and the reduction half-reaction is [tex]Fe^2^+(aq) + 2e^- - > Fe(s)[/tex].
The chemical reaction given is:
[tex]FeSO_4(aq) + Mg(s) - > MgSO_4(aq) + Fe(s)[/tex]
To write the half-reactions, we need to identify which species are being oxidized and which are being reduced. In this case, the Mg atom is being oxidized to [tex]Mg^2^+[/tex], while the [tex]Fe^2^+[/tex] ion is being reduced to Fe:
Oxidation half-reaction:
[tex]Mg(s) - > Mg^2^+(aq) + 2e^-[/tex]
Reduction half-reaction:
[tex]Fe^2^+(aq) + 2e^- - > Fe(s)[/tex]
To balance the half-reactions, we need to make sure that the number of electrons lost in the oxidation half-reaction is equal to the number of electrons gained in the reduction half-reaction. In this case, the oxidation half-reaction needs to be multiplied by 2 to balance the electrons:
[tex]2 Mg(s) - > 2 Mg^2^+(aq) + 4e^-[/tex]
[tex]Fe^2^+(aq) + 2e^- - > Fe(s)[/tex]
Now, we can add the half-reactions together to get a balanced overall reaction:
[tex]2 Mg(s) + FeSO_4(aq) - > MgSO_4(aq) + Fe(s)[/tex]
To learn about the chemical reaction:
https://brainly.com/question/31854853
#SPJ4
Which process caused initially by nitrogen monoxide emissions from jet or automobile engines is not involved in contributing to acid deposition?A: NO(g) + H2O(l) → H2NO2(aq)B: 2NO2(g) + H2O(l) → HNO2(aq) + HNO3(aq)C: 2NO(g) + O2(g) → 2NO2(g)D: 4NO2(g) + O2(g) + 2H2O(l) → 4HNO3(aq)
The process that is not involved in contributing to acid deposition is option C: 2NO(g) + O2(g) → 2NO2(g). This is because it does not involve the formation of any acid, unlike the other options which all result in the production of nitric acid (HNO3) or nitrous acid (HNO2) when combined with water.
Nitrogen monoxide (NO) is a precursor to the formation of nitrogen dioxide (NO2), which is the main contributor to acid deposition. NO2 reacts with water in the atmosphere to form nitric acid (HNO3) or nitrous acid (HNO2) depending on the conditions. Therefore, emissions from jet or automobile engines that contain NO contribute to acid deposition by reacting with other compounds in the atmosphere to form acid rain. It is important to control emissions of nitrogen oxides to reduce the impact of acid deposition on the environment.
learn more about acid here
https://brainly.com/question/26775834
#SPJ11
The reaction 2NO → N2 + O2 has the following rate law:delta [NO]/delta t = 2k[NO]^2After a period of 2.0 × 103 s, the concentration of NO falls from an initial value of 2.8 × 10-3 mol/L to 2.0 × 10-4 mol/L. What is the rate constant, k?
The rate constant for the given second-order reaction is [tex]\text{2.18}\times10^{-3}\text{ L/mol/s}\[/tex].
What is the rate constant for the second-order reaction given the concentration of NO at two different times?
We can use the integrated rate law for a second-order reaction to solve for the rate constant, k.
The integrated rate law for the given second-order(2nd) reaction is:
[tex]\frac{1}{[NO]_t}-\frac{1}{[NO]_0}=kt\[/tex]
where [NO]t is the concentration of NO at time t, [NO]0 is the initial concentration of NO, and k is the rate constant.
Putting in the given values:
[tex][NO]_t=\text{2.0}\times10^{-4}\text{ mol/L}\\\[NO]_0=\text{2.8}\times10^{-3}\text{ mol/L}\\\t=\text{2.0}\times10^3\text{ s}\[/tex]
we get:
[tex]\frac{1}{\text{2.0}\times10^{-4}}-\frac{1}{\text{2.8}\times10^{-3}}=k(\text{2.0}\times10^3)\[/tex]
Simplifying this expression:
[tex]k&=\frac{\frac{1}{\text{2.0}\times10^{-4}}-\frac{1}{\text{2.8}\times10^{-3}}}{\text{2.0}\times10^3}\[/tex]
[tex]k&=\text{2.18}\times10^{-3}\text{ L/mol/s}[/tex]
Therefore, the rate constant for this reaction is [tex]\text{2.18}\times10^{-3}\text{ L/mol/s}\[/tex].
To learn more about rate constant, visit: https://brainly.com/question/11211516
#SPJ4
Why were almost all of the original food color additives phased out?
Most of the original food color additives were phased out because they were found to be potentially harmful to human health.
Many of these early food color additives were synthetic compounds that were not tested for safety before being added to food, and their effects on the human body were not well understood.
For example, some early food color additives, such as Sudan I, II, III, and IV, were found to be carcinogenic (cancer-causing) in animal studies. Other color additives, such as Red 2G and Orange B, were found to cause cancer in rats and mice.
In addition to their potential health risks, some of these early food color additives were also found to cause allergic reactions in some people, or to exacerbate the symptoms of attention deficit hyperactivity disorder (ADHD) in children.
To know more about synthetic compounds here
https://brainly.com/question/13049450
#SPJ1
What is the hydronium-ion concentration of a 0.0029 M KOH solution?
a. 3.4 × 10-12 M
b. 2.9 × 10-3 M
c. 1.0 × 10-14 M
d. 1.0 × 10-7 M
e. 2.9 × 10-17 M
The hydronium-ion concentration of a 0.0029 M KOH solution is 3.4 x 10^-12 M. The correct option is (a) 3.4 x 10^-12 M in the given choices.
To determine the hydronium-ion concentration of a 0.0029 M KOH solution, we need to use the concept of dissociation of water and the equation for the ion product constant of water, Kw = [H3O+][OH-]. Since KOH is a strong base, it will dissociate completely in water to form K+ and OH- ions.
So, in the given solution, the OH- ion concentration will be 0.0029 M. Using the Kw equation, we can calculate the hydronium-ion concentration:
Kw = [H3O+][OH-]
1.0 x 10^-14 = [H3O+][0.0029]
[H3O+] = 1.0 x 10^-14 / 0.0029
[H3O+] = 3.4 x 10^-12 M
Therefore, the hydronium-ion concentration of a 0.0029 M KOH solution is 3.4 x 10^-12 M, which is option (a) in the given choices.
To know more about hydronium-ion click here:
https://brainly.com/question/14619642
#SPJ11
If a solvent has a lower Rf value than another in TLC plate, what does that mean?(oxidation lab)
If a solvent has a lower Rf value than another in TLC plate, that means it is a less polar solvent.
What does the solvent's Rf value reveal about it?
The relative distance the spot went in relation to the possible distance it could have gone if it had moved with the solvent front is indicated by the Rf value, which is a ratio. An Rf of 0.55 indicates that the spot migrated somewhat more than halfway, or by 55%, to the solvent front.
The most polar (fastest moving) point is the one with the highest Rf value, while the least polar (slowest moving) place is the one with the lowest Rf value. Rf values are routinely used to assess if a drug that is known and one that is unknown are the same.
To learn more about Rf value use:
https://brainly.com/question/29387153
#SPJ4
Which region of the nephron is permeable to water but not nacl?.
The descending limb of the loop of Henle in the nephron is permeable to water but not NaCl.
The loop of Henle is a crucial part of the nephron responsible for concentrating urine. The descending limb of the loop of Henle is permeable to water, which means water can move out of the tubule by osmosis. In contrast, the ascending limb of the loop of Henle is impermeable to water but permeable to salt.
It actively pumps out NaCl, creating a concentration gradient that drives the reabsorption of water in the descending limb. As a result, the urine becomes more concentrated as it travels down the descending limb, which is important for maintaining water balance in the body.
To learn more about nephron, here
https://brainly.com/question/12307837
#SPJ4
