the principle that allows a scissor lift to raise the platform on top of it to a considerable height can be illustrated with four freezer pop sticks attached at the corners. answer these questions about what happens to parallelogram abcd when you change its shape as in the illustration. a. is it still a parallelogram? explain. b. is its area the same? explain. c. compare the lengths of the diagonals in the two figures as you change them. d. describe a process that might be used to raise the platform on a scissor lift.

Answer:

F = - K X

X = .4314 m       compression of spring

F  = 55.71 N/m * .4314 m = 24.03 N      force to compress spring

E = 1/2 K X^2       energy of compressed spring

E = 1/2 55.71 N / m * (.4314 m)^2 = 5.184 Joules energy of spring    

1/2 M V^2 = E      energy imparted to ball

V = (2 E / M)^1/2 = 3.25 m/s     max speed of ball

M g H = 1/2 M V^2     calculate height of ball after release

H = E / (M g)      height above spring

H = 5.184 / (.98 * 9.80) = .540 m     height to which ball rises

.540 + .4314 = .972 m      height above compression point

Oscillation refers to the repetitive motion of an object that periodically returns to a fixed position. It can be described as the motion of an object back and forth around an equilibrium point.

Oscillations can be classified into different types based on the restoring force that causes the motion. The most common types of oscillations are harmonic oscillations, which are caused by a restoring force that is proportional to the displacement from the equilibrium point. A massless spring hanging from the ceiling with a small object attached to its lower end is a good example of harmonic oscillation. When the object is displaced from its equilibrium position and released, it will oscillate up and down, with its lowest position being 13 cm below yi.

This is a simple harmonic motion problem. The object oscillates about an equilibrium point, which is at yi. The amplitude of the oscillation is 13 cm, and the restoring force is provided by the spring. The motion can be described by the equation: y(t) = A * cos(2πft + φ), where A is the amplitude, f is the frequency, and φ is the phase constant. The frequency of the oscillation can be calculated using the formula: f = 1 / (2π * sqrt(k/m)), where k is the spring constant and m is the mass of the object.

To know more about oscillations visit:

https://brainly.com/question/30111348

#SPJ4

The average force an astronaut applies to the spacecraft's wall is 346.7 N, or impulse 104.

Average force refers to a force that changes over time and is not constant. It provides an more or less typically delivered that can be used to determine the other factors connected to it. On the contrary hand, net force describes all of the forces acting on the object.

Simply put, yes is the response to the question Can force be negative. A vector quantity, force depends on both its magnitude and its direction. Just the direction is indicated by the negative sign. An object's mass and acceleration are produced by the force.

To know more about Force visit:

https://brainly.com/question/29781083

#SPJ4

Answer:

v=150m/s

Explanation:

given

u=200m/s

t=5s

g=10m/s^2

required

v=?

solution

v=u-gt

v=200-(10)(5)

v=200-50

v=150m/s

Short Circuit Current Rating(SCCR) is the ability of a certain equipment to withstand a certain magnitude of electric current at a specific voltage during a short circuiting.

Short circuit is that when a neutral wire comes in contact with a current carrying live wire. During short circuiting, the current in the conductor suddenly gets increased due to the very low resistance. We know by Ohm's law that for a constant potential difference(V), the current(I) is inversely proportion to the resistance(R).

V = I/R

So when resistance becomes very low, the current becomes very high causing the spark, or high heat in the wire or the equipment. SCCR is the rating of equipment that can withstand a certain magnitude of current.

To know more about electric current, here

https://brainly.com/question/2264542

#SPJ4

If an object' mass is decreasing while constant force is applied to the object, the acceleration will increases option -c is correct.

Acceleration is the rate at which the speed and direction of a moving object change over time. When something speeds up or slows down, it is said to be accelerating. Motion on a circle accelerates even when the speed is constant because the direction is always changing.

An object's motion is altered by a net force; the greater the net force, the greater the acceleration. To accelerate at the same rate as less massive objects, heavier net forces are needed.

To know more about acceleration visit:

https://brainly.com/question/15430955

#SPJ4

The angular speed of the blade in radians per minute is 31,416 rad/min. angular and linear speeds the circular blade on a saw rotates at 5000 revolutions per minute.

If r is an object's radius, v is its linear speed and is its angular velocity in radians per unit of time, then v = r. This formula connects these three values so that we can always determine the third if we know the first two.

Thus, the angular speed times the r-dimensional distance equals the linear speed of a point on the object. The unit of measurement is meters per second and meters per second. where = the rate in radians per second.

(a) To find the angular speed of the blade in radians per minute, we can use the formula:

angular speed (rad/min) = 2 * pi * (revolutions per minute)

angular speed (rad/min) = 2 * pi * 5000 revolutions per minute

= 31,416 rad/min

(b) To find the linear speed of a blade tip, we can use the formula:

linear speed (inches/min) = (diameter of the blade) * (angular speed (rad/min))

linear speed (inches/min) = (diameter) * (angular speed (rad/min))

= (diameter) * (31,416 rad/min)

To know more about linear speed visit:

https://brainly.com/question/29345009

#SPJ4

The mirror that will be used in the fire extinguisher will be concave mirror.

When the concave mirror is exposed to the sun,all incident rays are converged to the focal point hence, energy radiated is focussed at a single point, hence paper burns, when it is kept at the focal point.

The real image formed only due to the concave mirror.this happens only if the object distance is greater than the focal length of the mirror.

real image, inverted image

when the object is placed at center of curvature, Image is formed at center of curvature,  Image is inverted, image is real.

To know more about concave mirrors visit:

https://brainly.com/question/3555871

#SPJ4

G = 9.8 m/s2 is the gravitational acceleration. Yo-weight yo's is m = 0.3 kg. The string's length is L = 0.25 meters. Yo-top-of-the-path yo's velocity is equal to 4 m/s. At the top of the walkway, there is tension in the string.

In simple terms, what is gravitational force?

Any two mass-containing objects are attracted to one another by the gravitational force. Because it consistently attempts to pull masses together rather than pushing them apart, the gravitational force is known as attractive. d

What is gravity, and what does it look like?

The term gravitational force refers to the force that the earth exerts on a body. A ball that is tossed up goes up in the air, as do the leaves and fruits that fall from a tree downward towards the ground.

To know more about gravitational force visit:

https://brainly.com/question/12550364

#SPJ4

The ball should make contact with the wall at point (3) in order to to make a collision with the greatest kinetic energy.

Any oscillatory motion can be considered a simple harmonic motion if –{1} : If the acceleration of the oscillating body is directly proportional to its displacement from the mean position.

{2} : And the direction of the acceleration vector (a) is towards the mean position.

{3} : For a body undergoing simple harmonic motion, we can write

Given is the wrecking crane shown below is moving toward a brick wall which is to be torn down.

The wrecking ball is undergoing simple harmonic motion. Now, the Kinetic energy of the wrecking ball is maximum at point (3). The potential energy of the ball will be maximum and same at the points (1) and (4). At point (2), the energy will be 50% Kinetic and 50% potential.

Therefore, the ball should make contact with the wall at point (3) in order to to make a collision with the greatest kinetic energy.

To solve more questions on simple harmonic motion , visit the link below-

https://brainly.com/question/28208332

#SPJ1

The preceding statement indicates that neither particle is right because their kinetic energies are equal.

A particles or a thing that is motion produces some form of energy called kinetic energy. An item accumulates kinetic energy when work, which involves the energy transfer, is made on it by exerting a net force. Explain that a moving object's mass and speed are two elements that impact the amount of kinetic energy it will possess.

Since the same potential difference is causing the acceleration of both particles (e and p), As KE=qV, where q is the same for electrons and protons, both have the same kinetic energy. The answer is (c), thus.

To know more about Kinetic energy visit:

https://brainly.com/question/25959744

#SPJ4

The complete question is-

A proton p and an electron e are released simultaneously on opposite sides of an evacuated area between large, charged parallel plates, as shown above. Each particle is accelerated toward the oppositely charged plate. The particles are far enough apart so that they do not affect each other. Which particle has the greater kinetic energy upon reaching the oppositely charged plate?

a). The electron.

b). The proton.

c). Neither particle, both kinetic energies are same.

d). It cannot be determined without knowing the amount of charges on the plates.

A) To find the velocity of the 3170 kg car before the collision, we can use the conservation of momentum principle. The principle states that the total momentum of a system remains constant if no external forces act on the system. In this case, the two cars form a closed system and no external forces are acting on them.

Given:

m1 = 2110 kg (mass of first car)

v1 = 10.2 m/s (velocity of first car)

m2 = 3170 kg (mass of second car)

v2f = 5.03 m/s (velocity of both cars after collision)

Using the conservation of momentum formula:

m1v1 + m2v2 = (m1 + m2)vf

2110 kg * 10.2 m/s + m2v2 = (2110 kg + 3170 kg) * 5.03 m/s

21632.2 + m2v2 = 5234.3 + 5.03 m/s

21632.2 = 5234.3 + m2v2

subtracting 5234.3 from both sides

16397.9 = m2v2

dividing both sides by m2

v2 = 16397.9/3170

v2 = 5.15 m/s

The velocity of the 3170 kg car before the collision is 5.15 m/s

B) To find the decrease in kinetic energy during the collision, we can use the conservation of energy principle. The principle states that the total energy of a closed system remains constant.

Given:

m1 = 2110 kg (mass of first car)

v1 = 10.2 m/s (velocity of first car)

m2 = 3170 kg (mass of second car)

v2 = 5.15 m/s (velocity of second car before collision)

vf = 5.03 m/s (velocity of both cars after collision)

Initial kinetic energy of first car = 1/2 * m1 * v1^2 = 1/2 * 2110 kg * 10.2 m/s^2 = 11096.2 J

Initial kinetic energy of second car = 1/2 * m2 * v2^2 = 1/2 * 3170 kg * 5.15 m/s^2 = 8073.36 J

Initial total kinetic energy = 11096.2 J + 8073.36 J = 19169.56 J

Final kinetic energy of both cars = 1/2 * (m1 + m2) * vf^2 = 1/2 * (2110 kg + 3170 kg) * 5.03 m/s^2 = 16100.57 J

Decrease in kinetic energy = Initial total kinetic energy - Final kinetic energy = 19169.56 J - 16100.57 J = 3068.99 J

The decrease in kinetic energy during the collision is 3068.99 J

If the albedo of a planet is 40% then it means that 40% of the sun's energy is reflected by the planet.

Albedo of a planet is the amount of solar energy that is reflected by a planet of surface. This term is used in astronomy to describe the reflective properties of a planet, satellite, or asteroids. Venus planet has the highest albedo in our solar system, which is 0.7 as a ratio of the light strikes the surface of the planet to the light reflected by the planet. Venus reflect 70% of the sunlight.

Albedo can be measured using  a pyranometer device or satellite imagery, which detects the solar radiation of shorter wavelength in the form of watts per square meter (W/sq m).  

To know more about albedo, here

https://brainly.com/question/12428220

#SPJ4

The impulse of the force for this 3.90 s is 104130 kg.m/s. the orbital maneuvering system (oms) on a space shuttle exerts a force of (26,700 n)1 for 3.90 s.

If the force is constant, the resulting force, F, and the length of this force, t, are multiplied to form the impulse of force. Changes in motion and subsequently changes in momentum are caused by the impulse of force.

a sudden, spontaneous propensity or invitation to some often irrational conduct. an inclination or inherent tendency that is typically illogical. an excitement pulse that travels through tissues, in particular nerve fibers and muscles, and causes physiological activity or inhibition by looking at nerve impulses.

Given:

(a) Force ∑F = 26700 N

Time interval Δt = 3.90 s

The impulse of force J = ∑F.Δt

The impulse of force J = 26700*3.90

The impulse of force J = 104130 Kg.m/s

(b) To find the change in momentum of the shuttle caused by this impulse, we can use the equation:

Δp = mΔv = Impulse

where Δp is the change in momentum, m is the mass of the shuttle (95,000 kg), and Δv is the change in velocity.

By using impulse equation we can find the change in velocity of the shuttle.

Δv = Impulse / m

= 104,130 Ns / 95,000 kg

= 1.096 m/s

You can plug in the value and find the change in velocity of the shuttle

To know more about force visit:

https://brainly.com/question/12785175

#SPJ4

you are on a pier on lake huron. if you jump in and are 10.9 ft below the surface of the water, what is the pressure? assume the atmospheric pressure is 13.9 psi and the density of the water is 61.0 lbm/ft^3.

Therefore, the total pressure at a depth of 10.9 ft below the surface of the water in Lake Huron is 1461.9 psi + 13.9 psi = 1475.8 psi.

To calculate the pressure at a depth of 10.9 ft below the surface of the water, you would use the formula for pressure due to a fluid: P = ρgh, where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the height of the fluid above the point of measurement.In this case, the density of the water is 61.0 lbm/ft^3, the acceleration due to gravity is 32.2 ft/s^2. So the pressure at a depth of 10.9 ft is: P = (61.0 lbm/ft^3)(32.2 ft/s^2)(10.9 ft) = 2088.82 lbf/ft^2 or 1461.9 psiIt's important to note that the pressure underwater increases by 1 atmosphere or 14.7 psi (or 14.7 lbf/in^2 or 101,325 Pa) for every 33 ft of depth, this means that you have to add the atmospheric pressure (13.9 psi) to the pressure calculated above. Therefore, the total pressure at a depth of 10.9 ft below the surface of the water in Lake Huron is 1461.9 psi + 13.9 psi = 1475.8 psi.

Learn more about  acceleration due to gravity here:

https://brainly.com/question/13860566

#SPJ4

The total work done by friction on the block (2 kg block starts at rest and is slides down a ramp from a height of 3.0 meters above the ground and reaches the ground with a kinetic energy of 50 J) as it slides down the ramp = 44 J (option 4)

When an external force is applied to a system in a such that one of the components of the force is parallel to the displacement of the system, mechanical energy—the sum of kinetic and potential energy—is transported into or out of the system. Work is the term for the activity of transferring energy.

The change in the block's mechanical energy is what is known as the work done by friction;

ΔME = W

KE - PE = W

(50 - (2 x 3) = W

W = 50 - 6

= 44 J

The question is incomplete, it should be:

A 2.0-kilogram block sliding down a ramp from a height of 3.0 meters above the ground reaches the ground with a kinetic energy of 50 Joules. The total work done by friction on the block as it slides down the ramp is approximately

(1) 6 J

(2) 9 J

(3) 18 J

(4) 44 J

Learn more about work done here: https://brainly.com/question/25573309

#SPJ4

The surface temperature of a star that emits twice the energy flux of the Sun would be 6900k.

What is energy?

Energy is the ability to do work. It can be found in a variety of forms, including thermal energy, kinetic energy, chemical energy, electrical energy, sound energy, and light energy. All of these forms of energy can be converted into other forms. Thermal energy is energy from heat, such as energy from a fire or from the sun.

Kinetic energy is the energy of movement, such as energy from a moving vehicle. Chemical energy is the energy stored in chemical bonds between atoms in a molecule. Electrical energy is energy from the movement of electrons, such as energy from a battery.

Given data:

Sun's temperature(Tsun) = 5800K

Energy flux of a star(Jstar) = 2J

Since,

Jstar/Jsun = T4sun/T4star

= 2 = (Tsun/Tstar)4

Tstar = T(2)[tex]^{1/4}[/tex]

         = 5800 × 1.1897

         = 6900k

To learn more about energy

https://brainly.com/question/13881533

#SPJ4

Michael pulled back the leash so that the dog could not run after the squirrel is an example of first law of motion because it is an action which is stronger than the force. Thus, the correct option is A.

Newton's first law of motion is also known as the law of inertia. It states that an object at rest will remain at rest and an object in motion will remain in motion with the same speed and direction unless and until it is acted upon by an unbalanced external force.

An external force can be defined as the change in the mechanical energy of the object which is either the kinetic energy of the object or the potential energy present in an object. These forces are caused through the external agents. Examples of external forces include friction, normal force, and air resistance.

Therefore, the correct option is A.

Learn more about Laws of motion here:

https://brainly.com/question/29775827

#SPJ1

Answer:

Explanation:

Work out can never be greater than work in because when work out is greater than work in, this means that more energy is being produced than what is being put into the system. This is not possible, as it would violate the law of conservation of energy, which states that energy cannot be created or destroyed, only transformed.

If work out were greater than work in, this would lead to an increase in efficiency, as the system would be able to produce more energy than what is being put into it. However, this increase in efficiency would be unsustainable, as it would eventually lead to an energy imbalance and a decrease in efficiency over time.

Gold ornaments look new even after several years because gold is a very stable metal and does not corrode or tarnish easily. It is also a very soft metal, which means that it does not scratch easily.

The shiny appearance of gold is due to its metallic luster, which is maintained even after many years.

Additionally, gold does not react with most chemicals, so it does not discolor or degrade over time. This means that gold ornaments can retain their original appearance for a long time.

The graph V as a function of r determines the potential of charge at different radius. This instructs how to estimate the charge-related electric field strength.

There won't be any net charge within the Gaussian surface if we suppose any imaginary sphere inside the charged sphere. So, Σq = 0 . So, the net flux is equal to 0. Consequently, a hollow sphere has no electric field inside of it.

The entire charge will be on the periphery of a conducting hollow sphere, and the electric field strength within the conducting sphere will be zero. The entire charge will reside on the shell's outside in the case of a spherical shell, and there will be no interior field as well.

Learn more about charge here:

brainly.com/question/1360238

#SPJ4

The kinetic energy acquired by the nail is: 91.5 J.

Kinetic energy is a form of energy that is associated with the motion of an object. It is the energy of a body or a system due to its motion. It is represented by the symbol K and is calculated by multiplying half of the object's mass with its velocity squared. Kinetic energy is always greater than zero and is equal to the amount of work needed to accelerate the body from its initial velocity to its final velocity.

The kinetic energy acquired by the nail when it is struck by the hammer can be estimated using the equation
KE = (1/2) mv^2
where m is the mass of the nail and v is the speed of the hammer.
In this case, m = 11.5 g and v = 4.36 m/s.
Therefore, the kinetic energy acquired by the nail is:
KE = (1/2) * 11.5 g * (4.36 m/s)^2
= 91.5 J.

To learn more about kinetic energy
https://brainly.com/question/114210
#SPJ4

For a standing wave with four nodes, you need a strength of 2 and a frequency. This creates a wave pattern with two loops, and four areas of minimum displacement.

what is frequency?

Frequency is a measure of how often something occurs, such as a sound wave or a particular event. It is expressed as a number of occurrences per unit time, such as vibrations per second, or as a fraction of the total number of occurrences over a specified interval, such as the proportion of a population that have a particular trait.

Frequency is an important concept in physics, engineering, mathematics, and other sciences. It is used to describe and analyze natural phenomena such as sound, light, and electricity, and to describe and analyze the behavior of systems such as mechanical, chemical, and biological systems.

To learn about more frequency.

https://brainly.com/question/254161

#SPJ4

Another method for locating vector components is to use the angle measured in the opposite direction from the +x axis. Then, the x-component will always be cos and the y-component will always be sin.

What is the resultant vector's formula?

R = A + B. Instance 2 To create the resulting vector, two vectors facing the opposite direction are subtracted from one another. Here, the vector B is pointing in the opposite direction of the vector A, and the resulting vector is called R.

What is the equation for a vector's component form?

Form of Component: A vector's component form is represented as v=vx,vy, where vx is the distance between the initial and terminal points in a horizontal direction and vy is the distance in a vertical direction.

To know more about vector components visit:

brainly.com/question/29708786

#SPJ4

Answer:

Heat capacity = (337207 J) / (5°C) = 67440.4 J/°C

Explanation:

mark me pls

A region. Since Region A has the most severe temperatures and the most dramatic changes in temperature over time, the observed effect is largest there.

How does temperature work?

Temperatures describe how hot or cold something is to a specific degree. Both Celsius and Fahrenheit are frequently used units of measurement, with Celsius being the more popular one.

With typical temperatures between -40 and 40 degrees Celsius, temperatures can fluctuate from extremely cold to extremely hot. Numerous variables, such as height, latitude, and closeness to the water, can influence temperature. It is crucial to be aware of the temperature in a specific place before going because various climates might experience drastically varying temperatures.

For such more question on Region .

https://brainly.com/question/22236101

#SPJ4

Note the complete question could be as bellow,

For which of the regions shown in the figure is the observed effect the strongest? O Region B O Region CO The observed effect is the same for all three regions O Region A

The Sierra Madre Oriental is located at number 4 on the map above; this is easy to remember because “oriental” is the Spanish word for “east.”

Oriental is a term used to describe the cultures, people, and products of the far East, especially those of East and Southeast Asia. It is also sometimes used to describe the cultures of North Africa and the Middle East. In its broadest sense, orientals are any people from the Orient, which is considered to be the regions east of the Mediterranean Sea. The term has also been used to describe aspects of the cultures of the countries within this region.

To learn about more Sierra Madre Oriental visit:

brainly.com/question/3985743

#SPJ1

A) The given statement is true, Masses are inertial.

B) The given statement is true, parallel to x axis x coordinate is variable y coordinate is constant.

C) The given statement is false, x component of velocity may be positive. For a cart moving along positive x axis towards origin the x component of velocity is negative.

Any particle of matter in the universe will gravitate toward any other with a force that varies directly as the product of the masses and inversely as the square of the distance between them, according to Newton's law of gravitation.

All of the universe's material objects are subject to the force of gravity, also known as gravitation. If there is a difference in mass between any two objects or particles, gravity will tend to pull them in that direction.

To know more about gravitational law visit:

https://brainly.com/question/858421

#SPJ4

The speed of the object at the height of (1/2)hmax is expressed in terms of vvv and ggg, without using the value of g and h.

Speed is what it means. the speed at which an object's location changes in any direction. The distance traveled about relation to the time it took to travel that distance is how speed is defined. Given that it just has a direction and no magnitude, speed is a scalar number.

The speed of the object at the height of (1/2)hmax can be represented by the equation:

Speed = sqrt(2gh)

Where:

g = acceleration due to gravity

h = height

At the height of (1/2)hmax, the object has reached its maximum height and its speed is at its minimum, known as the "top speed." At this point, the object's vertical velocity (vvv) is equal to zero and its kinetic energy is equal to its potential energy, so we can write:

1/2mvvv^2 = mgh

Where:

m = mass of the object

By substituting the first equation into the second equation, we get:

1/2m(sqrt(2gh))^2 = mgh

Simplifying this equation, we get:

g = vvv^2 / 2h

Now, we can substitute the value of g back into the first equation:

Speed = sqrt(2gh) = sqrt(2 * (vvv^2 / 2h) * (1/2)hmax)

So, the speed of the object at the height of (1/2)hmax is:

Speed = sqrt(vvv^2 / 2)

To know more about speed visit:

brainly.com/question/14885536

#SPJ4

The bear's snout will be traveling at 32 m/s when it reaches the honey.

What is honey?

Honey is a sweet and viscous liquid produced by bees, as well as other species of insects. It is composed primarily of sugars, but also contains trace amounts of enzymes, minerals, vitamins, and amino acids. It has been used for centuries as a food source and for its medicinal properties.

Honey has been used to treat coughs, colds, digestive issues, and topically to treat wounds, burns, and skin problems. Honey also has antioxidant, anti-inflammatory, and antiseptic properties. Its antibacterial properties make it a popular choice for wound care, and its antifungal properties can help to fight off fungal infections.

The bear's snout will be traveling at 32 m/s when it reaches the honey.

This is because acceleration is the rate of change of velocity,

which means that if an object accelerates at a rate = 2.0 m/s2

its velocity will increase by 2.0 m/s each second.

Therefore, if the bear accelerates at a rate of 2.0 m/s2 for 16 seconds, it will have a velocity of 32 m/s by the end of that time.

To learn more about honey

https://brainly.com/question/11169416

#SPJ4