the reason people cannot have everything they want is because of

When milling, technician A advises using the slowest speed for the end cut. According to technician B, the drum shouldn't be larger than its disposal diameter.

What is the process of milling?

Cleaning, grading, breaking down, sizing, separating, or classifying dry bulk materials are all included in the term "milling process." The mill is used in the actual milling process to grind, cut, or crush solid bulk materials into smaller bits. Ingilling is the practise of using a specialised machine to grind, cut, press, or crush a material. Cutting away material with a spinning cutter that has several teeth is called milling.

Know more about disposal Visit:

https://brainly.com/question/14732695

#SPJ1

Answer: The best engine depends on the specific application and intended use of the vehicle. Each engine type has its own strengths and weaknesses, and different types of engines are suited to different tasks. For example, an in-line 3 engine is smaller and more fuel efficient, making it a good choice for a compact car. A V8 engine, on the other hand, would be more powerful and better suited for a sports car or truck. Ultimately, the best engine for a specific vehicle depends on the specific needs and preferences of the manufacturer and consumer.

Explanation:

The best or the most efficient engine in the above list is w16 with the most complex mechanics.

A device created to transform one or more sources of energy into mechanical energy is known as an engine or motor. Potential energy, thermal energy, chemical energy, electric potential, and nuclear energy are all forms of energy that are readily available.

Prior to the release of the Veyron 16.4, which the French company referred to as a super sports vehicle, Bugatti debuted the renowned W16 engine in 2005. Since then, the Bugatti Chiron, the aforementioned Veyron, Divo, Bolide, and Centodieci have all had the W16 in their engine compartments.

Only three gasoline-powered V16 engine production vehicles in history were made, and two of them were by Cadillac. The first was employed in the Cadillac V-16 car from 1930 through 1937, and the second from 1938 to 1940.

To learn more about Engine refer to :

https://brainly.com/question/21127297

#SPJ1

Where two electricians are discussing outdoor receptacles. Electrician A says that one receptacle is required in the front and back of all dwelling types. Electrician B says the plans call for mounting the rear outdoor receptacle outlet six feet, six inches from the outside edge of a deck, the electrician that is correct is "Both" (Option A).

The National Electric Code (NEC) requires that all dwelling types have at least one receptacle in the front and back.

Furthermore, the NEC requires outdoor receptacles to be at least six feet, six inches from the outside edge of a deck. As a result, both electricians are correct in their assertions.

Learn more about receptacles:
https://brainly.com/question/28215225
#SPJ1

Where Anna is very picky about the temperature in her home and wants full control of airflow and heat/cooling. She should install a system that includes: "a low differential" (Option D)

The temperature differential in HVAC terms refers to the temperature difference between the inside and outside areas of the house.

The thermostat has an adjustable temperature differential setting that determines how frequently your system cycles. The lower the differential setting, the more frequently your system will cycle and the tighter the temperature will be maintained.

Learn more about Differential Heating:
https://brainly.com/question/28033741
#SPJ1

Where the Werner family is very cost-conscious and they want a system with low maintenance costs, the system they should avoid is: "Boiler System" (Option A)

Because the Werners want a system with low maintenance costs, a boiler system may not be the best option.

Regular maintenance and service are required for boiler systems, such as checking and cleaning the burners, replacing filters, and flushing the system to remove buildup. They also necessitate more frequent repairs as parts wear out, resulting in higher maintenance costs.

As a result, the Werners should avoid using a boiler system and instead consider alternatives such as a heat pump or a radiant ceiling system, which are known for their low maintenance costs and dependability.

Learn more about boilers:
https://brainly.com/question/14241641
#SPJ1

The number that Eric should use for his calculations is C. The sum of x and y

From the information, Eric is taking measurements in order to develop a quote for the installation of a home heating system. He's identified heat loss rates of x from ventilation and y from infiltration.

If X represents the ventilation loss and Y represents the infiltration loss, respectively, then Eric should use the sum of X and Y in his calculation to determine the total heat loss.

Therefore, based on the information, the correct option is C.

Learn more about ventilation in:

https://brainly.com/question/1121893

#SPJ1

Answer:

C. Conduction

Explanation:

Conduction is heat transfer through stationary matter by physical contact.

Where Martavis is installing a smart thermostat into a home built in the 1950s. The home still has the original steam boiler as its heat source and currently is set using the original dial thermostat. After connecting all of the old wires to the smart thermostat, Martavis notices that it doesn't turn on. Note that he most likely issue with the installation is: "There's no C wire since the original thermostat is older." (Option B)

Smart thermostats are Wi-Fi thermostats that can be used with home automation to control the heating, ventilation, and air conditioning in a home.

The most likely problem with installing a smart thermostat in a 1950s home is that the original thermostat does not have a "C" wire, which is typically used to provide a common power source to the thermostat. Smart thermostats require a "C" wire for power and will not function if the home does not have one.

Learn more about Smart Thermostat:
https://brainly.com/question/30112238
#SPJ1

Answer:D. Oxygen is used for respiration and carbon dioxide is a waste product.

Both animal and plant cells use oxygen for respiration, which is the process of converting nutrients into energy. During respiration, oxygen is consumed and carbon dioxide is produced as a waste product. In plant cells, photosynthesis also occurs, which is the process of using sunlight, carbon dioxide, and water to create glucose and oxygen. But respiration, consuming oxygen and producing carbon dioxide, is a common process that happens in both animal and plant cells.

Explanation:

After you have built a fountain for your backyard pond, you can control the

pump speed so the water doesn’t spray too high or too low by: Locating the pump's input control, which is usually on or near the bottom of the pump on the back or sides. This can appear as a switch that moves up and down, often with several options such as "F" for fast or "S" for slow speeds.

A conventional fountain is a system in which water flows from a source (Latin fons), fills a basin, and is emptied. Fountains can be either wall-mounted or free-standing. Water sheets may flow over various stone, concrete, or metal surfaces in fountains.

The pump pushes water upwards, causing it to fall into a lower basin. To restart the cycle, the pump uses water pressure and tubes to propel the water back into the reservoir. The number of reservoirs and pumps.

Learn more about Fountains:
https://brainly.com/question/26274805
#SPJ1

The total distance traveled at a velocity of 121 miles per hour for a time of 5 hours is of:

605 miles.

The relation between velocity, distance and time states that the velocity is obtained by the quotient of the distance by the time, as follows:

v = d/t.

In which:

The parameters for this problem are given as follows:

v = 121, t = 5.

Hence the distance is obtained as follows:

d = v x t

d = 121 x 5

d = 605 miles.

The problem asks for the total distance traveled at a velocity of 121 miles per hour for a time of 5 hours.

More can be learned about velocity, distance and time at brainly.com/question/4931057

#SPJ1

Where the Riseaux family is building a two-story home in northern Arizona on a large amount of acreage, note that the type of thermal storage system would likely best suit their needs is: "Geothermal" (Option C)

Geothermal energy storage is a type of energy storage that generates and stores energy by utilizing natural underground heat. It is regarded as one of the renewable energy alternatives capable of replacing fossil fuels in the present and future.

The relatively constant temperature of the earth is used to heat and cool the home in this type of system. It circulates water or an antifreeze solution through underground pipes, absorbing or releasing heat depending on the temperature inside the home.

Learn more about Thermal Storage Systems:
https://brainly.com/question/20540235
#SPJ1

Note that an air-conditioning system's automatic controller might directly control the: "motor of a large condenser fan" (Option C)

A condenser fan is a type of fan that is found near the condenser, as the name implies. Its purpose is to remove heat from the refrigerant inside the hollow passages of the condenser. When your air conditioner is turned on, the refrigerant at the evaporator coil absorbs heat from the inside of your home.

The automatic controller of an air-conditioning system is a device that controls the operation of the air-conditioning system. It has the ability to directly control the motor of the large condenser fan. This motor is in charge of blowing air over the condenser coils, which aids in the dissipation of heat absorbed by the refrigerant.

Learn more about air conditioning:
https://brainly.com/question/29648889?
#SPJ1

Note that where Eve's contractor recommended she not install baseboard heating. The scenario where would it be disadvantageous to install a baseboard heating system is: "Where there are low ceiling heights." (Option C)

The term "baseboard heat" refers to the position of the heater along the bottom of the wall. The idea behind this placement is that heat naturally rises, so by beginning along the floor, the heat gradually rises into the area between the floor and ceiling where you spend the majority of your time.

Baseboard heating systems, which are typically installed along the base of the walls, heat a room by relying on the natural rise of warm air. If the ceiling height is low, warm air may not have enough space to rise, resulting in poor heating performance and decreased efficiency.

Learn  more about Baseboard Heating:
https://brainly.com/question/5248745
#SPJ1

Answer:D. The blower continues to operate until the temperature within the fan unit rises above the setpoint of the internal controller, at which time the blower shuts off.

Explanation: i big brained thats y

Answer:Time-of-use billing is a pricing structure for electricity that charges different rates for electricity consumption based on the time of day it is used.

Explanation:

1) Where Roy intends to use a seam that is used for joining metals where extra stiffness is needed, such as roofs, air housing, ducts, and so forth, the best suggestion to Roy is for him to use: "standing seam (Option D)

2) Note that the word refers to a full-sized drawing of the various surface of an object stretched out on a flat surface is; "A development" (Option A)

3) The words the most commonly used to reinforce an edge, hide burrs and rough edges, and improve the appearance is: Hem (Option A)

A standing seam is a type of seam formed by turning up the edges of two adjacent sheets of metal roofing material and then folding or interlocking them in a variety of ways.

Roy can use a standing seam, which is a type of seam used for joining metals that require extra stiffness, such as roofs, air housing, and ducts.

Learn more about seams:
https://brainly.com/question/20381434
#SPJ1

Where the amount of time it takes for one BTU to flow across one square foot of surface when there's a one-degree difference in temperature from one side of the material to the other is known as: ".the R-value." (Option C)

The British thermal unit is a heat unit defined as the amount of heat needed to raise the temperature of one pound of water by one degree Fahrenheit. It is also one of the customary units used in the United States.

Note that the R-value is a measure of thermal resistance that indicates how long it takes for one Btu to flow across one square foot of surface when there is a one-degree temperature difference from one side of the material to the other. It is the inverse of the U-value (thermal transmittance), which is used to calculate heat loss.

Learn more about BTU:
https://brainly.com/question/7411071
#SPJ1