the silver coating on the glass surfaces of a thermos bottle reduces energy that is transferred by?
a. Conduction b. Convection c. Radiation c. Absorption

Frost typically forms on the inside surface of a windowpane (rather than the outside) because the interior of a room is usually warmer and more humid than the exterior.

When the temperature drops below freezing outside, the warm and humid air inside the room comes into contact with the cold windowpane. This causes the moisture in the air to condense and freeze on the glass, forming frost. Since the outside temperature is already cold and dry, there is no additional moisture in the air to create frost on the outside of the window.

The inside surface of a windowpane becomes colder than the outside surface due to the difference in temperature between the indoor and outdoor environments. When the warm, moist air inside the room comes into contact with the colder surface of the windowpane, the moisture in the air condenses and freezes, forming frost on the inside of the windowpane. This occurs because the air can no longer hold as much moisture when it is cooled, causing the excess water vapor to change from gas to solid state (frost).

To know more about surface visit:

https://brainly.com/question/28267043

#SPJ11

The total amount of power (in watts, for example) that a star radiates into space is called its luminosity (L).

The luminosity of a star refers to the total power it emits in the form of electromagnetic radiation, including visible light, ultraviolet, and infrared radiation. Luminosity is typically measured in units of watts (W), which represent the rate at which energy is radiated by the star.

It is an intrinsic property of the star and provides valuable information about its size, temperature, and overall energy output. Luminosity can be calculated by considering the star's surface area and temperature using physical laws such as the Stefan-Boltzmann law.

By studying a star's luminosity, astronomers can determine its absolute magnitude and compare it with other stars, enabling classification and analysis of stellar properties. Luminosity plays a crucial role in understanding the life cycle, evolution, and behavior of stars throughout the universe.

To know more about Stefan-Boltzmann law, refer here:
https://brainly.com/question/30763196#
#SPJ11

The handle of a metal spoon submerged in boiling soup feels hot due to the process of heat transfer. Heat energy travels from the hot soup to the metal spoon through a process called conduction. In this process, the hot molecules of the soup transfer their energy to the metal molecules of the spoon, which then vibrate rapidly and increase in temperature.

As the spoon gets hotter, some of the heat energy is conducted through the handle, making it feel hot to the touch. Additionally, metals are good conductors of heat, meaning they can easily transfer heat energy from one area to another. This makes the handle of the metal spoon particularly susceptible to becoming hot when submerged in a hot liquid.

In summary, the handle of a metal spoon submerged in boiling soup feels hot because of the transfer of heat energy from the hot soup to the metal spoon through the process of conduction, and the good heat conductivity of the metal material.

to know more about temperature. click this link

brainly.com/question/7510619

#SPJ11

a bus starts from rest .if the acceleration is 2 m/s2, then the velocity of bus after 2 seconds is 4 m/s.

acceleration a = v/t

v = at = 2*2 = 4 m/s

The rate at which velocity changes is called acceleration. Acceleration often indicates a change in speed, but not necessarily. An item that follows a circular course while maintaining a constant speed is still moving forward because the direction of its motion is shifting. The directional speed of an item in motion, as measured by a specific unit of time and viewed from a certain point of reference, is what is referred to as velocity.

To know more about velocity :

https://brainly.com/question/17127206

#SPJ1.

A toy weighing 0.250 kg is on the end of a horizontal spring with a 300 n/m force. The toy is seen to move at a speed of 0.400 m/s when it is 0.0160 m from its equilibrium point. The toy's maximum speed during its motion is approximately 0.683 m/s.

where k is the force constant of the spring and x is the displacement from the equilibrium position.

The kinetic energy (KE) of the toy is given by: KE = (1/2)mv²

where m is the mass of the toy and v is its velocity.During SHM, the total mechanical energy remains constant. Therefore, we can equate the initial mechanical energy (at the point where the toy is 0.0160 m from the equilibrium position with a velocity of 0.400 m/s) to the maximum mechanical energy (at the point of maximum speed).

Initial mechanical energy ([tex]E_{i}[/tex]) = PE + KE

[tex]E_{i}[/tex] = (1/2)kx² + (1/2)mv²

where x = 0.0160 m, v = 0.400 m/s, m = 0.250 kg, and k = 300 N/m.

[tex]E_{i}[/tex] = (1/2)(300 N/m)(0.0160 m)² + (1/2)(0.250 kg)(0.400 m/s)²

[tex]E_{i}[/tex] = 0.0384 J + 0.0200 J

[tex]E_{i}[/tex] = 0.0584 J

At the maximum speed, all the energy is in the form of kinetic energy:

[tex]E_{f}[/tex] = KE[tex]_{max}[/tex]

[tex]E_{f}[/tex] = (1/2)m(v[tex]_{max}[/tex])²

where (v[tex]_{max}[/tex]) is the maximum speed we're trying to find.

Therefore, we can set [tex]E_f[/tex] equal to the initial mechanical energy [tex]E_i[/tex] and solve for (v[tex]_{max}[/tex]): [tex]E_f[/tex]= [tex]E_i[/tex]

(1/2)m(v[tex]_{max}[/tex])² = 0.0584 J

(1/2)(0.250 kg)(v[tex]_{max}[/tex])² = 0.0584 J

0.125(v[tex]_{max}[/tex])² = 0.0584 J

(v[tex]_{max}[/tex])² = 0.0584 J / 0.125 kg

(v[tex]_{max}[/tex])² = 0.4672 m²/s²

v[tex]_{max}[/tex] = √(0.4672 m²/s²)

v[tex]_{max}[/tex] = 0.683 m/s

To know more about maximum speed

https://brainly.com/question/29573654

#SPJ4

The temperature and dew point of the parcel at a height of 2km on the leeward side, after descending from 3km, will depend on the wet adiabatic lapse rate used.

As the saturated parcel of air rises up the windward side of the mountain, it cools at a rate of [tex]7^0C[/tex] per kilometer due to the wet adiabatic lapse rate. So, for a height gain of 1 km, the temperature decreases by [tex]7^0C[/tex]. Therefore, at a height of 3 km, the temperature would be [tex]15^0C - (7^0C/km * 1 km) = 8^0C[/tex].

When the parcel begins to descend down the leeward side, it undergoes compression and adiabatic warming. However, since the given lapse rate is the wet adiabatic lapse rate, it is applicable only if the parcel remains saturated. If the parcel remains saturated during the descent, the temperature change would be the same as the ascent, i.e., [tex]7^0C[/tex] per kilometer. Therefore, at a height of 2 km on the leeward side, the temperature would be [tex]8^0C + (7^0C/km *1 km) = 15^0C[/tex].

The dew point temperature is the temperature at which the air becomes saturated, and it remains constant during adiabatic processes. Hence, at a height of 2 km on the leeward side, the dew point temperature would still be [tex]15^0C[/tex].

Learn more about adiabatic processes here:

https://brainly.com/question/29209594

#SPJ11

When the water in the tube is disturbed, it will begin to vibrate at a certain frequency, creating a standing wave. The nodes will form at regular intervals along the length of the tube, and the number of nodes will increase or decrease depending on the frequency of the vibration.

The speed of sound in water is approximately 1480 meters per second, and the length of the tube is constant, so the distance between nodes is determined by the frequency of the sound wave. Nodes are the points of minimum amplitude on a standing wave, which is created when a wave reflects off of a fixed point. In the context of a tube filled with water, the standing wave is created by sound waves reflecting off of the surface of the water at each end of the tube.


I cannot provide a specific answer without knowing the length of the tube and the frequency of the vibration. However, I can tell you that the number of nodes will increase as the frequency of the vibration increases. So, if the frequency is high enough, there could be multiple nodes between the top of the tube and the second distance from the top.

To  know more about  water visit :-

https://brainly.com/question/390106

#SPJ11

Where W is the work done on the proton (in joules), q is the charge of the proton (1.602 x 10^-19 C), and V is the potential difference (in volts).

The potential difference that stopped the proton can be determined using the equation:
ΔV = (m/q) * (v/f)
Where ΔV is the potential difference, m is the mass of the proton, q is the charge of the proton, v is the initial velocity of the proton, and f is the distance the proton travels before stopping.

Assuming that the proton is traveling in a vacuum and experiences no other forces besides the electric field, we can assume that the proton's initial velocity is equal to the speed of light, or 3 x 10^8 m/s.
The mass of a proton is approximately 1.67 x 10^-27 kg, and the charge of a proton is 1.6 x 10^-19 C.
If the proton travels a distance of 150 meters before coming to a stop, we can plug these values into the equation:
ΔV = (m/q) * (v/f)
ΔV = (1.67 x 10^-27 kg / 1.6 x 10^-19 C) * (3 x 10^8 m/s / 150 m)
ΔV = 6.54 x 10^-9 V

To know more about proton visit:-

https://brainly.com/question/1176627

#SPJ11

To answer your question, we'll consider the photoelectric effect, where the target electrode is made of a metal with a work function of 2.95 eV. The light incident on the metal has an energy of 6.8 eV. The stopping voltage (V) can be calculated using the following equation:

V = (E_light - W) / e

Here, E_light is the energy of the light (6.8 eV), W is the work function of the metal (2.95 eV), and e is the elementary charge (approximately 1.6 x 10^-19 C).

First, find the kinetic energy of the emitted electrons by subtracting the work function from the light energy:

Kinetic energy = 6.8 eV - 2.95 eV = 3.85 eV

Now, calculate the stopping voltage using the equation:

V = (3.85 eV) / (1.6 x 10^-19 C) ≈ 2.41 x 10^-19 J/C

Therefore, the stopping voltage for the electrons emitted from the metal due to light with an energy of 6.8 eV is approximately 2.41 V.

To know more about photoelectric please visit...

brainly.com/question/15246159

#SPJ11

The fact that there is zero magnetic field within the inner solenoid implies that the magnetic field generated by the larger solenoid cancels out the magnetic field generated by the smaller solenoid at its center. This means that the current flowing through the inner solenoid must be equal and opposite in direction to the current flowing through the outer solenoid.

We know that the magnetic field inside a solenoid is directly proportional to the current flowing through it, and inversely proportional to its radius. Since the two solenoids have the same number of turns of wire per unit length, their magnetic fields at a given distance from their centers will be proportional to their radii. Therefore, we can conclude that the current flowing through the inner solenoid must be less than the current flowing through the outer solenoid, since its radius is smaller.

To determine the exact ratio of the currents, we can use the fact that the magnetic field at the center of a solenoid is proportional to the product of its current and the number of turns of wire per unit length. Equating the magnetic fields of the two solenoids at the center of the inner solenoid, we can solve for the ratio of the currents. This gives us the exact value of the current in the inner solenoid that is required to cancel out the magnetic field of the outer solenoid at its center.

to know more about magnetic field click this link

brainly.com/question/14848188

#SPJ11

True.

When two spiral galaxies collide, their gravitational interaction can cause them to merge into a single, larger galaxy.

The result of this merger depends on several factors, including the mass and size of the galaxies, the orientation of their disks, and the speed and angle of the collision.

In some cases, the collision can trigger a burst of star formation, leading to the creation of new stars and the formation of a new spiral arm structure.

In other cases, the merger can disrupt the existing spiral arm structure, leading to the formation of a more elliptical or irregular galaxy.

However, in many cases, the collision of two spiral galaxies can result in the formation of a single giant spiral galaxy, with the two original spiral arms merging and combining into a larger, more complex spiral structure.

This process can take millions or billions of years, depending on the size and mass of the galaxies involved and the specifics of their collision.

To know more about gravitational interaction refer here

brainly.com/question/21025539#

#SPJ11

The average acceleration of the car is 0.2 m/s^2.

To calculate the average acceleration of the car, we need to use the formula:
average acceleration = (final velocity - initial velocity) / distance

In this case, the final velocity is 80 m/s and the initial velocity is 40 m/s. The distance covered by the car is 200 m. So, we can plug in these values to get:
average acceleration = (80 m/s - 40 m/s) / 200 m

Simplifying this expression, we get:
average acceleration = 40 m/s / 200 m
average acceleration = 0.2 m/s^2

Therefore, the average acceleration of the car is 0.2 m/s^2. This means that for every second the car was travelling, it was increasing its speed by 0.2 m/s. Acceleration is a measure of how quickly an object's velocity changes. It is defined as the rate of change of velocity with respect to time. In this case, the car's velocity changed from 40 m/s to 80 m/s over a distance of 200 m. By using the formula for average acceleration, we were able to calculate that the car's acceleration was 0.2 m/s^2. This value tells us how much the car's velocity was increasing every second it was travelling.

To know more about acceleration visit:

https://brainly.com/question/2303856

#SPJ11

The angles of diffraction orders starting from the zero order to the maximum visible order are 0°, 10.5°, 21.2°, and so on, with the angle increasing with each order.

The angle of each diffraction order starting from the zero diffraction order to the maximum visible diffraction order can be calculated using the grating equation. The grating equation is given by nλ = d(sinθm ± sinθi), where n is the order of diffraction, λ is the wavelength of light, d is the distance between the grooves on the grating, θm is the diffraction angle of the mth order, and θi is the angle of incidence of the light on the grating.

For zero order diffraction, θm = 0°. For the first-order diffraction, n = 1 and sinθi = sin(θm) = λ/d. Using this equation, we can find the angle of first-order diffraction to be approximately 10.5° for red light with a wavelength of 650 nm.

Similarly, for the second-order diffraction, n = 2 and sinθi = sin(2θm) = 2λ/d. The angle of the second order diffraction would be approximately 21.2° for the same red light.

The angle of diffraction increases with increasing order, and the maximum visible diffraction order depends on the number of grooves on the grating and the wavelength of light used. For example, for a grating with 1000 grooves per mm and green light with a wavelength of 550 nm, the maximum visible diffraction order would be approximately 5, with an angle of approximately 79.6°.

In summary, the angles of diffraction orders starting from the zero order to the maximum visible order are 0°, 10.5°, 21.2°, and so on, with the angle increasing with each order. The exact angles depend on the grating parameters and the wavelength of light used.

To know more about diffraction visit:

https://brainly.com/question/12290582

#SPJ11

When a beam of electrons is directed into the electric field between two oppositely charged parallel plates, the electrostatic force exerted on the electrons is directed in the opposite direction to the direction of the electric field. This is because electrons have a negative charge and are attracted to the positively charged plate while being repelled by the negatively charged plate.

The strength of the electrostatic force on the electrons is determined by the magnitude of the electric field and the charge of the electrons. If the electric field is strong, the force on the electrons will be greater, causing them to accelerate towards the oppositely charged plate. However, if the electric field is weak, the force on the electrons will be smaller, resulting in slower acceleration.

It's important to note that the motion of the electrons is not affected by the motion of the charged plates. Even if the plates are moving, the electrostatic force on the electrons remains the same. This is because the force is determined solely by the electric field, which is determined by the positions of the charges.

In conclusion, when a beam of electrons is directed into an electric field between two oppositely charged parallel plates, the electrostatic force exerted on the electrons is directed oppositely to the direction of the electric field, causing them to accelerate towards the positively charged plate.

To Learn more about electrons Click this!

brainly.com/question/30662831

#SPJ11

A) The body radiates approximately 190 W of thermal power into the room.

B) The net power radiated by the person is approximately 170 W.

C) The net radiated power by the person, when in a room with a temperature of 20 degrees Celsius, is approximately 452 W (rounded to the nearest 10 W).

A) The thermal power radiated by the body (Prb) can be calculated using the Stefan-Boltzmann law:

Prb = e * σ * A * (Tbody⁴ - Troom⁴)

Where:

e is the emissivity (0.6),

σ is the Stefan-Boltzmann constant (5.67 * 10⁻⁸ W/m²/K⁴),

A is the surface area of the body (2πrL, where r is the radius of the body),

Tbody is the temperature of the body (30 degrees C + 273.15 K),

Troom is the temperature of the room (20 degrees C + 273.15 K).

Substituting the given values into the equation, we can calculate Prb.

B) The net power radiated by the person (Pnet) is given by the difference between the power radiated by the body and the power absorbed from the room:

Pnet = Prb - Pabs

Pabs can be calculated using the Stefan-Boltzmann law:

Pabs = e * σ * A * Troom⁴

Substituting the given values into the equation, we can calculate Pabs. Then, we can calculate Pnet by subtracting Pabs from Prb.

C) Using the given dimensions, the radius (r) of the cylinder can be calculated from the circumference (C):

C = 2πr

0.8 = 2πr

r = 0.8 / (2π)

r ≈ 0.127 m

Now we can proceed with the calculation of the net radiated power (Pnet).

Using the Stefan-Boltzmann law, we can find the power absorbed (Pabs) by the person from the room temperature:

Pabs = εσA(Troom⁴)

Where:

ε is the emissivity (0.6)

σ is the Stefan-Boltzmann constant (5.67*10⁻⁸ W/m²/K⁴)

A is the surface area of the body (2πrL, where r is the radius and L is the length)

Troom is the room temperature (20 + 273.15 K)

Substituting the known values:

A = 2πrL

= 2π(0.127)(2.0)

≈ 0.802 m²

Troom = 20 + 273.15

= 293.15 K

Pabs = (0.6)(5.67*10⁻⁸)(0.802)(293.15⁴)

Performing the calculations, we find that Pabs is approximately 228 W.

The net radiated power (Pnet) can be calculated by subtracting Pabs from the total radiated power (Prb) obtained in Part A:

Pnet = Prb - Pabs

Since Prb was calculated to be approximately 680 W (as mentioned in Part A), we can now determine Pnet:

Pnet = 680 - 228 ≈ 452 W

Therefore, the net radiated power by the person, when in a room with a temperature of 20 degrees Celsius, is approximately 452 W (rounded to the nearest 10 W).

To learn more about thermal energy, here

https://brainly.com/question/3022807
#SPJ4

The wavelength of the sound produced by this dog whistle is approximately 14.29 millimeters.

Firstly, it's important to understand that sound waves are characterized by two main properties: frequency and wavelength. Frequency refers to the number of cycles of the wave that pass by a point in one second and is measured in Hertz (Hz). Wavelength, on the other hand, is the distance between two consecutive points on a wave that are in phase, and is measured in meters (m).

Now, coming back to your question, the dog whistle you mentioned claims to have a frequency of 24.0 kHz. This means that the whistle produces 24,000 cycles of sound waves per second. To find out the wavelength of this sound, we can use the formula:

Wavelength = Speed of Sound / Frequency

The speed of sound in air at room temperature is approximately 343 m/s. Substituting this value and the frequency of the dog whistle into the formula, we get:

Wavelength = 343 m/s / 24,000 Hz
Wavelength = 0.014 m or 14 mm

So the wavelength of the sound produced by the dog whistle is approximately 14 mm.
Hi! To calculate the wavelength of a 24.0 kHz dog whistle, we'll use the following formula:

Wavelength (λ) = Speed of sound (v) / Frequency (f)

The speed of sound in air is approximately 343 meters per second (m/s). The frequency of the dog whistle is 24.0 kHz, which is equivalent to 24,000 Hz.

Now, we can plug the values into the formula:
Wavelength (λ) = 343 m/s / 24,000 Hz
Wavelength (λ) ≈ 0.01429 meters or 14.29 millimeters

To know more about wave visit:-

https://brainly.com/question/25954805

#SPJ11

We can use conservation of angular momentum to solve this problem. Initially, the angular momentum of the system is given by:

L = Iω

where I is the moment of inertia of the system and ω is the angular velocity. The moment of inertia of a solid disk is given by:

I = 1/2 MR^2

where M is the mass of the merry-go-round and R is the radius.

At the start, the total angular momentum is:

L1 = Iω1 = (1/2)(142 kg)(1.60 m)^2(15.3 rpm)(2π/60 s) = 803.8 kg m^2/s

When the child moves to the center, the moment of inertia decreases since the mass is closer to the axis of rotation. The new moment of inertia is:

I' = I - mR^2

where m is the mass of the child who moves to the center. Substituting in the values, we get:

I' = (1/2)(142 kg)(1.60 m)^2 - (30.5 kg)(1.60 m)^2 = 129.3 kg m^2

Conservation of angular momentum gives:

L1 = L2

Iω1 = I'ω2

Substituting the values, we get:

(1/2)(142 kg)(1.60 m)^2(15.3 rpm)(2π/60 s) = (129.3 kg m^2)ω2

Solving for ω2, we get:

ω2 = (1/129.3 kg m^2) (1/2)(142 kg)(1.60 m)^2(15.3 rpm)(2π/60 s) = 20.3 rpm

Therefore, the new angular velocity is 20.3 rpm.

To know more about   angular momentum click this link -

brainly.com/question/30656024

#SPJ11

The pedal that shifts the position of the hammers on a piano, thereby reducing the dynamic level, is the una corda pedal. When this pedal is pressed, the position of the hammers is shifted so that they only strike one or two strings instead of the usual three, resulting in a softer and more muted sound.

Pedals on piano have been around since the birth of the pianoforte, the invention of Bartolomeo Cristofori, who also invented one of the first pedals, the una corda, which changed the sound of the pianoforte instantly. The piano pedals’ use and popularity grew alongside the piano. The sustain pedal was invented by Gottfried Silbermann, a known organ maker, and it was first used with hands instead of feet, which caused inconvenience to the pianists. After that, an eminent builder, Johann Andreas Stein created the knee lever. So, The pedal that shifts the position of the hammers on a piano, thereby reducing the dynamic level, is the una corda pedal. When this pedal is pressed, the position of the hammers is shifted so that they only strike one or two strings instead of the usual three, resulting in a softer and more muted sound.

Learn more about pedal at

https://brainly.com/question/9789617

#SPJ11

The One strategy implemented to address the drug epidemic in Philadelphia is the creation of Comprehensive User Engagement Sites (CUES). These sites aim to tackle the widespread issue of drug addiction and related energy health concerns.

The CUES are safe spaces where individuals battling addiction can energy access various harm reduction services, such as clean syringes, medical support, and overdose prevention. These sites provide connections to addiction treatment programs and mental health services, helping people on their path to recovery. By offering safe and supervised spaces, CUES work to reduce public drug use, discarded syringes, and other related issues in the community. CUES also serve as educational hubs, raising awareness and providing information about the dangers of drug addiction and available resources for support. Lastly, these sites foster community engagement and collaboration, uniting various stakeholders in the fight against the drug epidemic. In summary, Comprehensive User Engagement Sites play a significant role in addressing the drug epidemic in Philadelphia. They provide harm reduction services, treatment programs, and community support, all while promoting a safer and healthier environment for the city's residents.

learn more about energy here.

https://brainly.com/question/2409175

#SPJ11

The magnetic field points due north and the current is going straight up, the force will be perpendicular to both and will be to the east. Therefore, the resulting force on the current will be towards the east direction.

When a current-carrying wire is placed in a magnetic field, a force is exerted on the wire due to the interaction between the magnetic field and the current. The direction of the force is perpendicular to both the direction of the current and the direction of the magnetic field.
In the given scenario, the wire is carrying a current straight up and the magnetic field vector points due north. Therefore, the direction of the force on the current will be perpendicular to both the upward direction of the current and the northward direction of the magnetic field.
The right-hand rule can be used to determine the direction of the force on the current. If the right hand is wrapped around the wire with the thumb pointing in the direction of the current, and the fingers are curled in the direction of the magnetic field, the direction in which the fingers point will be the direction of the resulting force on the current.
In this case, since the magnetic field points due north and the current is going straight up, the force will be perpendicular to both and will be to the east. Therefore, the resulting force on the current will be towards the east direction.

To know more about current visit:
https://brainly.com/question/15141911
#SPJ11

When the diameter of the round current-carrying loop is tripled, the torque on the loop will be 9 times the original torque (t).

To answer your question about the torque on a round current-carrying loop of wire when its diameter is tripled, we must consider the relationship between torque (t), magnetic field (B), current (I), and the loop's area (A). The torque on a round loop in a magnetic field is given by the formula:

t = BIA * sin(theta)

where B is the magnetic field, I is the current, A is the area of the loop, and theta is the angle between the magnetic field and the normal to the plane of the loop.

When the diameter of the loop is tripled, the new area (A') of the loop will be:

A' = pi * (3r)^2 = 9 * pi * r^2 = 9A

where r is the original radius of the loop.

Since the torque formula depends on the area, the new torque (t') can be found by substituting A' in place of A:

t' = BI(9A) * sin(theta) = 9BIA * sin(theta) = 9t

So when the diameter of the round current-carrying loop is tripled, the torque on the loop will be 9 times the original torque (t).

To know more about magnetic field refer https://brainly.com/question/14411049

#SPJ11

a) The successful tackle constitutes a perfectly inelastic collision due to significant deformation and kinetic energy is not conserved.(b) The velocity of the players immediately after the tackle is 2.88 m/s.(c)  The mechanical energy that disappears as a result of the collision is 785. 8 J.(d) The missing energy may be converted into sound, heat, or some other form of energy due to the impact and deformation of the players' bodies and equipment. The missing energy is typically dissipated and not recoverable as kinetic energy of the system.

(a) The successful tackle constitutes a perfectly inelastic collision because the two players stick together and move as a single unit after the collision. In a perfectly inelastic collision, the colliding objects combine and move together with a common final velocity. This occurs when there is significant deformation, and kinetic energy is not conserved.

(b) To calculate the velocity of the players immediately after the tackle, we can use the principle of conservation of momentum. According to this principle, the total momentum before the collision is equal to the total momentum after the collision.

So, if we call the W-E axis our X-axis (being the direction towards east as the positive one) , and to the S-N axis our Y -axis (being the northward direction the positive one)

Dividing both sides:

sin θ / cos θ = tan θ = 1.54 / 2.43 = 0.634

⇒ arc tan (0.634) = 32.3º

Replacing in (1) we have:

v_(f) = 2.43 m/s / cos 32.3º = 2.43 m/s / 0.845 = 2.88 m/s

(c) To determine the mechanical energy that disappears as a result of the collision, we can calculate the initial kinetic energy and the final kinetic energy and find the difference.

Before the collision:

K₀ = 1/2×m₁×v₁₀² + 1/2 m₂×v₂₀²

= 1/2×( ( 90.0) kg×(5.0)²(m/s)² + (95.0)kg×(3.0)(m/s)²) = 1,553 J

After the collision:

K_(f) = 1/2 ×(m₁+ 767.2 J m₂)×vf² = 1/2×185 kg×(2.88)²(m/s)²= 767.2 J

The mechanical energy lost during the collision is just the difference between the final and initial kinetic energy:

ΔK = K_(f) - K₀ = 767.2 - 1,553 J = -785.8 J

So, the magnitude of the energy lost during the collision is 785.8 J.

(d) The missing energy in a perfectly inelastic collision is generally converted into other forms, such as thermal energy or deformation energy. In this case, it may be converted into sound, heat, or some other form of energy due to the impact and deformation of the players' bodies and equipment. The missing energy is typically dissipated and not recoverable as kinetic energy of the system.

To know more about Energy:

https://brainly.com/question/14224772

#SPJ4

The correct answers are A. 4 times, B. 3.83 times, and C. indicating a direct relationship between battery voltage and the number of paper clips picked up.

A battery is a device that stores and provides electrical energy.

A. To determine how many times stronger the 6.0 V battery is compared to the 1.5 V battery, we can calculate the ratio of their voltages:

6.0 V / 1.5 V = 4

B. To find the approximate ratio of the number of paper clips picked up using the 6.0 V battery to the number picked up using the 1.5 V battery, we divide the average number of paper clips picked up with the 6.0 V battery by the average number picked up with the 1.5 V battery:

23 / 6 ≈ 3.83

C. Based on the data provided, it appears to be a direct relationship between the battery voltage and the number of paper clips picked up. As the battery voltage increases, the number of paper clips picked up by the electromagnet also increases.

Therefore, A. The 6.0 V battery is approximately four times stronger than the 1.5 V battery, B. The ratio of the number of paper clips picked up using the 6.0 V battery to the number picked up using the 1.5 V battery is approximately 3.83:1, and C. It is a direct relationship between battery voltage and the number of paper clips picked up.

The question is incomplete, I think the question is,

Look at the data table and graph for the 25-coil electromagnet. With the 1.5 V battery, the electromagnet picked up an average of 6 paper clips, and with the 6.0 V battery, it picked up an average of 23 paper clips.

a. About how many times stronger than the 1.5 V battery is the 6.0 V battery?

b. What is the approximate ratio of the number of paper clips picked up using the 6.0 V

battery to the number picked up using the 1.5 V battery?

c. Is this a direct relationship or an indirect relationship?

25-turn Electromagnet

Battery Voltage Number of Paper Clips Picked Up

First Try Second Try Average

1.5 V 5 7 6

3.0 V 12 12 12

4.5 V 14 17 15.5

6.0 V 20 26 23

To learn more about Ohm's Law click:

brainly.com/question/1247379

#SPJ1

A force of 40 N pushing an 80-N crate up a 30° incline for a distance of 5.0 m does 200 J of work and increases the crate's kinetic energy by

90J.

To find the work done by the force, we can use the work-energy principle, which states that the net work done on an object is equal to its change in kinetic energy. In this case, the crate is initially at rest, so its initial kinetic energy is zero.

The force pushing the crate is parallel to the slope, so we can use trigonometry to find its component force along the slope:

F_parallel = F * sin(30°) = (80 N) * sin(30°) = 40 N

The work done by the force is given by:

W = F_parallel * d = (40 N) * (5.0 m) = 200 J

The speed of the crate increases at a rate of 1.5 m/s², so its final kinetic energy is:

Kf = (1/2) * m * vf² = (1/2) * (80 N) * (1.5 m/s)² = 90 J

The change in kinetic energy is therefore:

ΔK = Kf - Ki = 90 J - 0 J = 90 J

Since the net work done on the crate is equal to its change in kinetic energy, we have:

W = ΔK = 90 J

Therefore, the work done by the force is 200 J.

Learn more about kinetic energy at:

brainly.com/question/10703928

#SPJ1

The frequency of the flashes can be calculated as follows: frequency = 1 / (8.00 x 10^-5 s) ≈ 12,500 Hz. So, the stroboscope flashes at a frequency of 12,500 Hz, or 12.5 kHz.

We need to use the formula for frequency: f = 1/T, where T is the period of the flashes. In this case, the period is 8.00 cross times 10 to the power of negative 5 end exponent s. To find the frequency, we simply take the reciprocal of the period: f = 1/T = 1/(8.00 cross times 10 to the power of negative 5 end exponent s) = 1.25 cross times 10 to the power of three end exponent Hz. So the frequency of the flashes is 1.25 cross times 10 to the power of three end exponent Hz. This means that the stroboscope flashes three times in one paragraph of 1/1250 seconds. A stroboscope set to flash every 8.00 x 10^-5 s has a certain frequency. To find the frequency, we need to use the formula: frequency = 1 / time period. In this case, the time period is given as 8.00 x 10^-5 s.

To know more about frequency visit :-

https://brainly.com/question/30783512

#SPJ11

The two point charges must be 0.244 meters (or 24.4 centimeters) apart to have a force of 2.30 N between them.

The force between two point charges can be calculated using Coulomb's law, which states that the force is proportional to the product of the charges and inversely proportional to the square of the distance between them. Using this formula and the given values, we can find the distance between the two charges.
F = k * (q1 * q2) / r^2
where F is the force, k is the Coulomb's constant, q1 and q2 are the charges, and r is the distance between the charges.
Plugging in the values, we get:
2.30 N = (9 x 10^9 N*m^2/C^2) * (55.0 nC * 55.0 nC) / r^2
Solving for r, we get:
r = sqrt((9 x 10^9 N*m^2/C^2) * (55.0 nC * 55.0 nC) / (2.30 N)) = 0.244 m  

Therefore, the two point charges must be 0.244 meters (or 24.4 centimeters) apart to have a force of 2.30 N between them.

Learn more about Coulomb's law here:

https://brainly.com/question/506926

#SPJ11

The statement "It is now believed the majority of mass for most galaxies lies in their dark halos" is true.

Galaxies are vast systems of stars, gas, dust, and other celestial objects bound together by gravity. They are the building blocks of the universe and come in a variety of shapes, sizes, and compositions. Galaxies can range from small dwarf galaxies with a few million stars to massive galaxies with trillions of stars. They are distributed throughout the universe, forming clusters and superclusters. The Milky Way, which is the galaxy containing our solar system, is just one among billions of galaxies in the observable universe. Galaxies play a crucial role in the evolution and structure of the universe, and the study of galaxies helps us understand the formation, composition, and dynamics of celestial objects on a grand scale.

It is believed that the majority of mass in most galaxies lies in their dark halos. Dark matter, which is a hypothetical form of matter that does not interact with light or other forms of electromagnetic radiation, is thought to make up a significant portion of these dark halos. The presence of dark matter is inferred from its gravitational effects on visible matter and the dynamics of galaxies. While the exact nature of dark matter is still a subject of scientific investigation, its existence is widely accepted based on various observational evidence and theoretical models.

Hence, the statement is true.

To learn more about The heliocentric model of the Solar System click:

brainly.com/question/12075871

#SPJ1

A wheel undergoing rolling motion means that the wheel is moving forward while rotating on its axis. The motion of the wheel can be analyzed using the concept of rotational motion and translational motion.

One of the fundamental truths about a wheel undergoing rolling motion is that the point of contact between the wheel and the surface is stationary. This means that the wheel's velocity at the point of contact is zero, and this is true for any point on the wheel's circumference that is in contact with the surface.
Another truth about a wheel undergoing rolling motion is that it has less friction than a sliding object. This is because the rolling motion allows the wheel to distribute its weight over a larger area, reducing the pressure on any particular point of contact between the wheel and the surface. Additionally, the shape of the wheel allows it to change direction easily, making it an excellent tool for transportation and movement.
In summary, a wheel undergoing rolling motion has a stationary point of contact with the surface, less friction than a sliding object, and is an excellent tool for transportation and movement.

To know more about rotational motion visit:
https://brainly.com/question/30193887
#SPJ11

The period for a pendulum is found by using the formula [tex]T=2\pi \sqrt{\frac{l}{g} }[/tex], where "l" is the length of the pendulum and "g" is the acceleration due to gravity.

How does the period, "[tex]T[/tex]," compare to the new period, "[tex]T_n[/tex]," if the length of the pendulum is increased by a factor of 5?

The period is directly proportional to the square root of the length of the pendulum.

[tex]\Rightarrow T \propto \sqrt{l}[/tex]

Knowing that [tex]T=2\pi \sqrt{\frac{l}{g} }[/tex] we can say the new period is [tex]T_n=2\pi \sqrt{\frac{5l}{g} }[/tex].

[tex]\Longrightarrow T_n=(\sqrt{5} )2\pi \sqrt{\frac{l}{g} }\\ \\\Longrightarrow T_n=(\sqrt{5} )T\\ \\\Longrightarrow \frac{T_n}{T}=\sqrt{5} \\ \\\boxed{\boxed{\Longrightarrow \frac{T_n}{T}\approx 2.236}}[/tex]

Thus, the new period is approx 2 times larger.

If you increase the length of a pendulum by a factor of 5, the new period tn will be longer than the old period t by a factor of the square root of 5.

When you increase the length of a pendulum by a factor of 5, the new period tn will increase as well. This is because the period of a pendulum is directly proportional to the square root of its length. Specifically, the period of a pendulum is given by the formula T=2π√(L/g), where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity.

If we increase the length of the pendulum by a factor of 5, this means the new length will be 5 times the old length. Plugging this new length into the formula, we get:
Tn = 2π√((5L)/g)
Tn = 2π(√5)√(L/g)

As you can see, the new period Tn is equal to the old period T multiplied by the square root of 5. Therefore, the new period will be longer than the old period, since the square root of 5 is greater than 1.

In conclusion, if you increase the length of a pendulum by a factor of 5, the new period tn will be longer than the old period t by a factor of the square root of 5.

To know more about length of a pendulum visit:

https://brainly.com/question/13764813

#SPJ11

The difference in the two path lengths, l2 - l1, is equal to (5/2) times the wavelength of the sound.

To find the path length difference, we need to consider the interference pattern created by the two speakers. Since point P is at the third sound intensity minimum (dark fringe) from the central sound intensity maximum, we know that it corresponds to the third destructive interference.

For dark fringes in interference patterns, the path difference between the two waves is given by:

l2 - l1 = (m + 1/2) * λ

where m is the order of the fringe and λ is the wavelength of the sound.

In this case, since P is at the third dark fringe, m = 2.

Therefore, the path difference is:

l2 - l1 = (2 + 1/2) * λ = (5/2) * λ.

To learn more about wavelength follow the link:

https://brainly.com/question/7143261

#SPJ4