the skaters then rotate around the center of the pole. assume that the friction between skates and ice is negligible. what are (a) the radius of the circle, (b) the angular speed of the skaters, and (c) the kinetic energy of the two-skater system? next, the skaters pull along the pole until they are separated by 1.0 m. what then are (d) their angular speed and (e) the kinetic energy of the sy

A third mass of 0.30 kg needs to be hung at a height of 30 cm.

a numerical representation of the fundamental aspect of all material, inertia. It generally refers to the body of matter's opposition to changing its velocity or location in response to the force applied to it. The change caused by an applied force is lower the more mass a body has.

Clockwise and counterclockwise torques must balance

4 * (50 - 20) = .6 * (80 - 50) + .3 * L

g is left out here because it will cancel

Here we are assuming  the mass at L will generate aclockwise torque along with the .6 kg mass

so L is measured to the right of the 50 cm mark.

Solving the above equation  (12 - 18) / .3 = L =-20

So the weight must be hung at 50 - 20 = 30 cm

To know more about mass visit :

https://brainly.com/question/30337818

#SPJ4

The wavelength of red light in the visible spectrum is longer than that of blue light. In general, red light has a wavelength range of around 620–750 nanometers, while blue light has a wavelength range of around 450–495 nanometers.

Chlorophyll, the pigment that is responsible for photosynthesis in plants, primarily absorbs light in the blue and red regions of the visible spectrum. Chlorophyll reflects green light, which is why most plants appear green. Chlorophyll a absorbs the most light in the blue-violet and red (about 430 and 662 nm, respectively), while chlorophyll b absorbs in the blue and orange-red (about 453 and 642 nm, respectively)s why most plants appear green. Chlorophyll a absorbs the most light in the blue-violet and red (about 430 and 662 nm, respectively), while chlorophyll b absorbs in the blue and orange-red (about 453 and 642 nm, respectively). This is why it seems as if the chlorophyll reflects green.

Learn more about wavelength:

https://brainly.com/question/19448078

#SPJ4

The kinetic energy of a body whose mass is 150kg covering a total distance of 115km/hr is 76,512.27J.

Kinetic energy is the energy possessed by an object because of its motion, equal (nonrelativistically) to one half the mass of the body times the square of its speed.

Kinetic energy = ½ mv²

Where;

According to this question, a body of mass 150kg is covering a total distance of 115km/hr.

115km/hr = 31.94m/s

K.E = ½ × 150 × 31.94²

K.E = 76,512.27J

Therefore, 76,512.27J is the kinetic energy of the body.

Learn more about kinetic energy at: https://brainly.com/question/26472013

#SPJ1

The magnitude of the football's resultant displacement is 52.81 yards.

The given parameters;

   initial displacement backwards = 10 yards

   final displacement forward = 50 yards

   vertical displacement = 15 yards

The resultant horizontal displacement, x = 50 yards - 11 yards = 61 yards

The resultant vertical displacement, y = 17 yards

The magnitude of the football's resultant displacement is calculated by applying Pythagoras theorem as shown below;

R² = y² + x²

R² = 50² + 17²

R² = 2789

R = √2789

R = 52.81 yards

Thus, the magnitude of the football's resultant displacement is 42.72 yards.

To know more about football displaced visit:

https://brainly.com/question/11827445

#SPJ4

The reason we use the kelvin scale for thermodynamic and dynamic meteorological equations is because it is an absolute temperature scale that relates directly to kinetic energy and volume.

Using the Kelvin scale of temperature, it is easy to represent many fundamental laws and their associated mathematical equations. The Kelvin scale is a scale of absolute temperature, with zero at absolute zero. As an absolute scale, the Kelvin scale does not allow for degrees to be used in measurements.

Given that it only measures positive values and that its zero point is the temperature of absolute zero, the Kelvin scale is an absolute scale. The lowest theoretical temperature, or zero Kelvin, is the point at which a body can no longer lose thermal energy.

To know more about kelvin scale visit:

https://brainly.com/question/13290721

#SPJ4

Sound waves travel through the air and can be blocked by walls. When a sound wave passes through a wall, the wall absorbs some of the sound energy, resulting in the higher-pitched sound waves being blocked more than lower-pitched sound waves.

This is because higher-pitched sound waves have shorter wavelengths, making them more susceptible to being blocked than lower-pitched sound waves, which have longer wavelengths.

This phenomenon is known as wave-particle duality, which states that sound waves have both particle-like and wave-like properties. The particle-like property of higher-pitched sound waves makes them more susceptible to being blocked by walls than lower-pitched sound waves. This is why you can hear lower-pitched sounds more clearly when they pass through a wall.

Learn more about sound waves:

https://brainly.com/question/16093793

#SPJ4

The planet's orbital radius is the properties can be inferred from the star’s orbital period. Hence option 'a' is correct.

An orbital period is the time it takes for an astronomical object to complete an orbit around another object. In astronomy, it often refers to objects revolving around the Sun, such as planets or asteroids, as well as moons revolving around other star, exoplanets, and the double stars.

A satellite's mass does have an impact on its orbit. The orbital period & radius of the satellite are influenced by its mass. A satellite's orbital period and radius will be shorter and smaller if it has higher mass.

To know more about orbital period visit :

https://brainly.com/question/554614

#SPJ4

The officer might want to determine the driver's identity and verify that the driver has a valid driver's license. The officer could also use the flashlight to look for signs of intoxication, such as bloodshot eyes or a strong odor of alcohol.

What is the flashlight?

A flashlight is a device that emits a concentrated beam of light when powered by a battery. Flashlights are handheld, portable light sources that can be used to illuminate dark areas and enhance visibility in low-light situations. Flashlights come in a variety of sizes and shapes and typically use either an incandescent bulb or a light emitting diode (LED) as a source of light. Flashlights are mainly used for recreational activities such as camping, hiking, hunting and fishing, but they are also essential tools for emergency personnel and security guards.

To learn more about flashlight

https://brainly.com/question/4026955

#SPJ4

(2 pts.) What is the weight of the fish.spring with spring constant k = 340 N/m is used to weigh a 6.7-kg fish. a. (2 pts.)

What is weight ?

Weight is a measurement of the force of gravity on an object or person. It is typically measured in units of mass such as kilograms, pounds, or ounces. Weight is an important factor in determining a person's overall health, as well as their ability to perform physical tasks.

The spring stretches 0.2 m.

Fspring = F = ma = 340N = 6.7kg * a

a = 340N/6.7kg = 50.7 m/s^2

Δx = vt = 0 * t = 0

Δx = (1/2)at^2 = (1/2)(50.7 m/s^2)(t^2)

t = √(2Δx/a) = √(2*0.2m/50.7 m/s^2) = 0.2 m

To learn about more weight

https://brainly.com/question/229459

#SPJ4

The box reaches the bottom of the incline sooner than the disk by a distance equal to mgh/sin(θ). Express your answer in terms of some or all of the variables m , h , θ , and R , as well as the acceleration due to gravity g.

what is disk ?

A disk is a round, flat data storage device that is used in computers. It is composed of a metal or plastic disk and encased in a hard material such as metal, plastic, or rubber. The disk is divided into concentric circles, or tracks, which are divided into sectors. Data is stored on the disk in the form of magnetic or optical signals.

A disk drive is a device used to read and write data from and to a disk. It includes a spindle, which is the rotating part of the drive that holds the disk, and a read/write head that is used to read and write data. Data is read from and written to the disk by the read/write head, which is capable of moving along the surface of the disk.

To learn about more disk .

https://brainly.com/question/25996355

#SPJ4

Answer:[tex]\sqrt{\frac{3h}{gsin^2(\theta)} }-\sqrt{\frac{2h}{gsin^2(\theta)}}[/tex]

Explanation:

Arcology is the fusion of architecture with ecology, a comprehensive urban perspective. In nature, as organisms evolve, they increase in complexity and become a more compact system. A city should similarly evolve, functioning as a living system.

Arcology's major goal is to stop urban sprawl, which can be accomplished by building self-sufficient, remote settlements and structures that are (ideally, gigantic).

While it is theoretically conceivable to construct an arcology, at least structurally, it would take creative engineering to ensure the essential energy generation, food production, and waste reclamation systems are sustainable.

Learn more about Arcology here:

https://brainly.com/question/28811052

#SPJ1

Answer:

The concept of arcology that appealed to me the most is the fusion of architecture with ecology. If I were to incorporate an arcology concept into my community design, I would focus on creating a pedestrian environment where pedestrians move efficiently and freely.

Explanation:

Since Hailey is on the cart with Christine and Conner is on the other cart. Hence, it is determined that Conner's mass is 93 kg.

It is the most central tenant of matter and one of the essential quantities in physics. As a way to gauge how much matter is there in a body, we might use the term mass. The kilograms is the SI unit of mass (kg). A body's mass does not alter at any point in time.

Adult men and women can utilize the body-mass index (BMI), an assessment of body fat based on height and weight. Body Mass Index (BMI) is determined by dividing a person's kilograms divided by their height in metres squared (or feet).

Learn more about mass here:

brainly.com/question/12323246

#SPJ4

The density of gold can be calculated by dividing the mass of the gold nugget (16.60 g) by the volume of water it displaces (in cm3).

The density of a material can be calculated by dividing the mass of the material by its volume. The formula is Density = Mass/Volume. In this case, the mass of the gold nugget is given (16.60 g) and the volume of water it displaces can be measured by reading the graduated cylinder.

To calculate the density of gold, we need to know the volume of water that the gold nugget displaces. To find the volume, we can subtract the initial water volume (V1) from the final water volume (V2) after the gold nugget has been added. We can then use the formula density = mass/volume to find the density of the gold nugget.

Density = mass / volume

Density of gold = 16.60 g / (V2 - V1)

The volume of water displaced by the gold nugget needs to be measured in order to calculate the density of the gold nugget.

To know more about gold nugget visit:

brainly.com/question/28507154

#SPJ4

Given that it has a 1.5 m wavelength The wave moves 0.75 m in one second as a result it takes the wave 8 seconds to move 6.0 meters in the x-direction.

Newton's First Law of Motion (Inertia) An object at rest remains at rest, and an object in motion remains in motion at constant speed and in a straight line unless acted on by an unbalanced force.

The wavelength of the wave is given as 1.5 meters and it is traveling in the x-direction. The speed of a wave can be calculated using the formula:

Speed = Wavelength / Period

Since the wave is crossing the x-axis every second, its period is 1 second. So, the speed of the wave can be calculated as:

Speed = 1.5 meters / 1 second = 1.5 meters/second

To find out how long it takes the wave to travel 6 meters in the x-direction, we can use the formula:

Time = Distance / Speed

Time = 6 meters / 1.5 meters/second = 8 seconds

To know more about wave motion visit:

https://brainly.com/question/15006260

#SPJ4

Answer:

8.0

Explanation:

The stated difference in air pressure between the outside and interior of a residence is 1528.86 Pa. (where the wind speed is zero).

The blades of a turbine, which resemble propellers and function much like an aeroplane wing, capture the wind's energy. A pocket or minimal air develops on one blade's other side as the wind blows. The blade is subsequently drawn into the low-pressure air pocket, which turns the rotor. It is known as lifting.

Spped of wind out side the home V₁ = 109 mph

= 109 * 1.608 Kmph

= 175.272Kmph

= 48.686 m/s

Spped of wind inside the home V₂ = 0 Kmph

Density of air ρ = 1.29Kg/m³

Bernoulli's equation states:

Pressure difference P = [tex]\mathrm{P}_2-\mathrm{P}_1=\frac{1}{2} \rho\left(v_1^2-v_2^2\right)[/tex]

= 0.5 * 1.29 * (48.686)²

= 1528.86 Pa

To know more about Wind visit:

https://brainly.com/question/15321264

#SPJ4

If a 0.55 kg tennis ball is struck by a tennis racket with 12 N of force pointing right, then the acceleration on the tennis ball will be 21.82m/s²

The acceleration of a tennis ball is determined by the equation

a = F/m, where a is the acceleration, F is the force, and m is the mass. In this example, the force is 12 N and the mass is 0.55 kg. Thus, the acceleration of the tennis ball is 21.82 m/s².

a=12/0.55

=21.82 m/s²

The direction of the acceleration is determined by the direction of the force. Since the force is pointing right, the acceleration will also be pointing right. This means that the speed and velocity of the tennis ball will both increase as it moves in the right direction.

In addition, the acceleration will cause the ball to accelerate and reach a terminal velocity. This means that the speed of the ball will eventually reach a maximum and then remain constant. This is due to the force of gravity and the air resistance caused by the ball moving through the air.

Learn more about acceleration:

https://brainly.com/question/26246639

#SPJ4

Work is described as the force applied over a distance, so

W = Fxd

F = W/d = 400 mJ / 0.1 m = 4000 N

So the average force exerted by the it on the ground is 4000 N.

If work is done then there are three components involved. These are the amount of force, the distance of the displacement, and the reason behind the displacement. After multiplying force and distance for work, we get the unit of joules.

Work is the usage of force to move an object. It is directly related to the force involved and the distance the thing moves. Work can be calculated with: Work = Force x Distance.

To know more about displacement, visit here:

https://brainly.com/question/30087445

#SPJ4

With the frequency set at 1 Hz, if the inductance of the inductor is increased the maximum current increases. An increase in inductance of the inductor in an AC circuit will cause an increase in the maximum current.

The maximum current will rise when the inductor's inductance in an AC circuit increases. This is due to the fact that an increase in inductance also results in an increase in inductive reactance, which is the resistance to changes in current. In order to keep the same voltage across the inductor as the inductive reactance grows, the circuit's current must also grow. The inductive reactance is exactly inversely proportional to the inductance at a fixed frequency of 1 Hz, therefore as the inductance rises, the maximum current rises as well.It's also important to mention that the maximum current in an AC circuit is the peak current and in a sinusoidal wave the peak current is the RMS value multiplied by the square root of 2.

learn more about AC circuit here:

brainly.com/question/14835982

#SPJ4

The ranking of the boxes from largest to smallest is (d) 150 N pushing on 7 kg box, > (f) 150 N pushing on 1 kg box, > (a) 140 N pushing on 5 kg box, > (b) 140 N pushing on 3 kg box, > (e) 130 N pushing on 7 kg box, > (c) 120 N pushing on 3 kg box.

There are two forces acting on each book, perpendicular to each other. One is the pushing force, which is acting normal to the wall and the other one is gravitational force(weight) of the box acting downwards.

For box a) weight of the box, = 5 × 9.81 = 49.05 N

Pushing force on the box(a), = 140 N

Resultant force, R₁ = √(140²+49.05²) = 148.34 N

Similarly for box (b), R₂ = = √(140²+29.43²) = 143.06 N

Similarly for box (c), R₃ = = √(120²+29.43²) = 123.56 N

Similarly for box (d), R₄ = = √(150²+68.67²) = 164.97 N

Similarly for box (e), R₅ = = √(130²+68.67²) = 147.16 N

Similarly for box (f), R₆ = = √(150²+9.81²) = 150.32 N

So the ranking from largest to smallest force would be, d > f > a > b > e > c.

To know more about gravitational force, here

https://brainly.com/question/12528243

#SPJ4

The common angular speed is 6.5 x 10^⁻⁴ rad/s

To calculate the common angular speed of the reels during play, we need to first determine the linear speed of the tape on the outer reel. We can use the formula:

Linear speed = tape length / play time

So the linear speed of the tape on the outer reel is:

Linear speed = 281 m / (2 h * 3600 s/h)

                       = 0.078 m/s

Then we can use the formula for linear speed to find the angular speed:

Linear speed = angular speed x radius

So the angular speed of the outer reel is:

Angular speed = Linear speed / radius

= 0.078 m/s / (45 mm / 1000 m/mm)

= 1.7 x 10^⁻⁴ rad/s

The inner reel radius is 12mm, so the angular speed of the inner reel is:

Angular speed = Linear speed / radius

= 0.078 m/s / (12 mm / 1000 m/mm)

= 6.5 x 10^⁻⁴ rad/s

This is the common angular speed of the reels when both have the same angular speed.

Learn more about angular speed from

https://brainly.com/question/20432894

#SPJ1

calculate the amplitude at point on the string a distance of 17.0 cm from the left-hand end of the string. express your answer in meters.

In this case, we are given the distance of the point from the left-hand end of the string, but we are not given the amplitude of the source. So, we cannot calculate the amplitude at the point using the information provided.

To calculate the amplitude at a point on a string, we need to know the amplitude of the source that is vibrating the string and the distance the point is from the source. To calculate the amplitude at a point on the string a distance of 17.0 cm from the left-hand end of the string, we can use the equation for a sinusoidal wave: y(x,t) = A * sin (2π (f(t-x/v)) ). Where A is the amplitude, f is the frequency, λ is the wavelength, t is time, v is the speed of the wave, and x is the position along the string.. Let's assume that the amplitude of the wave at the left-hand end of the string is A0. The amplitude at a distance of x = 17.0 cm from the left-hand end of the string is given by: A = A0 * cos(2π(x/λ)). We know that the distance is given in centimeters, but the formula is in meters, so we need to convert it to meters. The distance 17cm is equal to 0.17m. The amplitude at a point 17.0 cm from the left-hand end of the string is: A = A0 * cos(2π(0.17m/λ)).

Learn more about amplitude here:

https://brainly.com/question/8662436

#SPJ4

False: The radius of the circular route changes when the test-mass riser is moved along the platform.

A circular route is what?

In contrast to a linear road, which follows a straight line, a circular path has a circular form or loop. It is a kind of motion that frequently occurs in mathematics, engineering, and physics. Circular routes are frequently used in engineering to explain the motion of components like wheels, gears, and pulleys.

In mathematics, rotations, orbits, circles, and other types of curves are frequently represented as circular routes. Circular routes may be employed in design, architecture, and other fields as well.

For such more question on test-mass.

https://brainly.com/question/13670753

#SPJ4

The speed of the cars just after the collision is 0.875 m/s.

What is the calculated ?

The calculated answer will depend on the context of the question. Without more information it is not possible to provide a definitive answer.

The calculated answer is not possible to provide without knowing the question.

The calculated answer is not possible to determine without more information. Depending on the question and the associated data, the answer could vary.

This can be calculated using the conservation of momentum: Momentum before collision

Momentum after collision(14,000 kg x 1.50 m/s) + (10,000 kg x 0 m/s) = (24,000 kg x v),21,000 kg m/s = 24,000 kg x v,v = 21,000 kg m/s / 24,000 kg

= 0.875 m/s

To learn more about calculated

https://brainly.com/question/30120309

#SPJ4

Explanation:

according to formula

efficiency= work output/work input

:. 0.30=work output/120

work output = 36J

hope this helps you.

The galaxy that would appear to be the youngest when we look at a photograph of many galaxies assuming that all of these galaxies formed at the same time after the big bang is the one that is farthest away (option C)

The youngest and farthest galaxy that scientists have seen is GN-z11. This video pans to the object's distance of 32 billion light-years.

High-redshift galaxy GN-z11 can be found in the constellation Ursa Major. It was the farthest known galaxy ever found from Earth.

The 2016 publication led by Pascal Oesch and Gabriel Brammer revealed the 2015 discovery (Cosmic Dawn Center). With a spectroscopic redshift of z = 10.957, or a proper distance of roughly 32 billion light-years, GN-z11 was the oldest and most distant known galaxy yet identified in the observable universe until the James Webb Space Telescope found JADES-GS-z13-0 in 2022. (9.8 billion parsecs).

The question is incomplete, it should be:

Suppose that we look at a photograph of many galaxies. Assuming that all galaxies formed at about the same time, which galaxy in the picture is the youngest?

a. the one that is reddest in color

b. the one that is bluest in color

c. the one that is farthest away

d. the one that is closest to us e. the one that appears smallest in size

Learn more about galaxies here: https://brainly.com/question/13956361

#SPJ4

After the stopcock is opened the final pressure in the flask is 172.92 torr, the final partial pressure of H2 is 492 torr, and the final partial pressure of N2 is 0.376 atm.

The final partial pressures of H2 and N2 after the stopcock between the two flasks is opened are given by the Ideal Gas Law (PV=nRT).

The Ideal Gas Law states that the product of the pressure, volume, and molar amount of a gas is equal to the product of the universal gas constant, R, and the temperature.

At constant temperature, the product of pressure and volume is directly proportional to the number of moles of gas, n. Therefore, when the stopcock is opened, the number of moles of H2 and N2 in the final flask is the sum of the number of moles in the original flasks.

The number of moles of H2 in the first flask is given by n1 = (P1V1) / (RT) = (492 torr x 2.00 L) / (0.0821 atm x L / mol x 273K) = 0.0428 mol

The number of moles of N2 in the second flask is given by n2 = (P2V2) / (RT) = (0.376 atm x 1.00 L) / (0.0821 atm x L / mol x 273K) = 0.0141 mol

The final number of moles of H2 and N2 is n = n1 + n2 = 0.0428 mol + 0.0141 mol = 0.0569 mol

After the stopcock is opened, the final pressure is equal to the product of the number of moles, n, and the ideal gas constant, R, and the temperature divided by the final volume Vf,

Pfinal = nRT / Vf = 0.0569 mol * 0.0821 atm x L / mol x 273K / 3.00 L = 0.0227 atm

In torr, the final pressure is Pfinal760 = 0.0227760 =172.92 torr.

The final partial pressure of H2 is 492 torr and the final partial pressure of N2 is 0.376 atm.

In conclusion, after the stopcock is opened the final pressure in the flask is 172.92 torr, the final partial pressure of H2 is 492 torr, and the final partial pressure of N2 is 0.376 atm.

Read more about the pressure:

brainly.com/question/25736513

#SPJ4

The density of air decreases as the altitude increases. The Temperature value decreases as the pressure value decreases with an increase in altitude.

The density of air or atmospheric density, denoted ρ, is the mass per unit volume of Earth's atmosphere. Air density, like air pressure, decreases with increasing altitude. It also changes with variation in atmospheric pressure, temperature and humidity. At 101.325 kPa (abs) and 20 °C (68 °F), air has a density of approximately 1.204 kg/m3 (0.0752 lb/cu ft), according to the International Standard Atmosphere (ISA). At 101.325 kPa (abs) and 15 °C (59 °F), air has a density of approximately 1.225 kg/m3 (0.0765 lb/cu ft), which is about 1⁄800 that of water, according to the International Standard Atmosphere (ISA).[citation needed] Pure liquid water is 1,000 kg/m3 (62 lb/cu ft).

Air density is a property used in many branches of science, engineering, and industry, including aeronautics; gravimetric analysis; the air-conditioning industry; atmospheric research and meteorology; agricultural engineering (modeling and tracking of Soil-Vegetation-Atmosphere-Transfer (SVAT) models); and the engineering community that deals with compressed air.

Learn more about density of air at https://brainly.com/question/3551743.

#SPJ4

Time of flight  is the  time flea in the air from the time it jumps to the time it hits the ground 0.64 seconds.

Time of flight= 2 time of ascent=[tex]2\times(\frac{u}{g} )[/tex]=[tex]2\times (\frac{3.13}{9.8})[/tex]=0.64 seconds

The time it takes for an object, particle, or wave (whether acoustic, electromagnetic, etc.) to traverse a distance across a medium is measured as time of flight (ToF). This data can then be used to determine the particle's or medium's attributes or to measure the particle's or path's velocity or length (such as composition or flow rate).The amount of time it takes the body to rise to its highest point from its starting posture is known as the ascension time. Complete solution, step-by-step For a projectile motion, the time to reach maximum height is called time of ascent.

Learn more about Time of flight

brainly.com/question/29105895

#SPJ4

The height and velocity of the football are calculated below.

What is velocity?

Velocity is a vector quantity that describes the rate of change of an object's position in a specific direction. It is defined as the displacement (change in position) of an object per unit time. The units of velocity are typically meters per second (m/s) or kilometers per hour (km/h). Velocity can also be represented by a vector arrow pointing in the direction of motion, with the magnitude of the arrow representing the speed of the object.

A. The greatest height reached by the ball can be calculated using the equation:

h = v_i^2 / (2 * g)

where h is the height, v_i is the initial velocity, and g is the acceleration due to gravity (approximately 9.8 m/s^2).

To find h:

h = (v_i^2) / (2 * 9.8)

B. To find the initial velocity, we can use the equation:

v_f^2 = v_i^2 + 2 * a * d

where v_f is the final velocity, v_i is the initial velocity, a is the acceleration (in this case, the acceleration due to gravity), and d is the distance traveled.

The distance traveled is the height of the ball at its highest point, which we found in part A. Since the ball is coming back down, final velocity will be zero.

v_f = 0

and the distance traveled is h.

Therefore,

v_i^2 = 2 * 9.8 * h

Finally, the initial velocity can be found by taking the square root of v_i^2.

To learn more about velocity from the given link:

https://brainly.com/question/25749514

#SPJ4

The color of light that travels faster in crown glass is red.

The speed of light in crown glass is the speed of light in a vacuum divided by the index of refraction of crown glass.

The speed of light traveling in vacuum = 3 times 10 to the 8 meters per second

The index of refraction of the crown glass for red light = 1.513

The index of refraction of the crown glass for blue light = 1.529

Therefore:

The speed of red color = 1.983 times 10 to the 8 meters per second

The speed of blue color = 1.962 times 10 to the 8 meters per second

Hence, the red light travels faster.

To learn more about light travels, click here:

https://brainly.com/question/1831789

#SPJ4