Very large transformers are sometimes designed not to have optimum regulation properties in order for the associated circuit breakers to be within reasonable size due to economic reasons.
Designing the circuit breaker for optimum voltage and current ratings would require a large number of turns of low voltage, heavy current windings which are costly.
Moreover, large transformers can lead to voltage drops if not designed properly which could lead to damages to the system,
thus sometimes manufacturers are forced to compromise on regulation properties of transformers in order to save money and avoid voltage drops as it is much cheaper to install circuit breakers that are designed for larger transformers.
Regarding the second question, the heating of transformers will not be approximately the same for resistive, inductive, capacitive loads of the same VA rating.
This is because each type of load (resistive, inductive, and capacitive) has a different power factor, which affects the current drawn by the transformer and the consequent heating.
Resistive loads draw current in phase with the voltage, while capacitive loads draw current leading the voltage, and inductive loads draw current lagging behind the voltage.
To know more about transformers visit:
https://brainly.com/question/15200241
#SPJ11
Which of the following statements correctly describe the functions of a freewheel diode in a switching circuit with a single switch? (Multiple answers possible, but wrong answers will deduct marks) O A freewheel diode functions as an uncontrolled switch - its switching state is only reliant on the voltage applied across it. O For an inductive load in a switching circuit, a freewheel diode must be placed in parallel with the inductive load. O A freewheel diode is a fully controllable switch. ✔✓ For an inductive load in a switching circuit, a freewheel diode provides a path for the load current to circulate, thus preventing an inductive voltage spike that could damage the switch immediately after it is turned off. O For an inductive load in a switching circuit, a freewheel diode must be placed in series with the inductive load to store energy.
A freewheel diode provides a path for the load current to circulate, thus preventing an inductive voltage spike that could damage the switch immediately after it is turned off is the correct statement to describe the function of a freewheel diode in a switching circuit with a single switch.
A freewheel diode is not a fully controllable switch. It is also not a switch that functions as an uncontrolled switch because its switching state is not only reliant on the voltage applied across it. For an inductive load in a switching circuit, a freewheel diode must be placed in parallel with the inductive load because it provides a path for the load current to circulate.
The freewheel diode has a reverse bias in this configuration, so it does not contribute to the current flow. It will, however, dissipate the energy stored in the inductive load when the switch is turned off.
To know more about immediately visit:-
https://brainly.com/question/14988926
#SPJ11
A 400A 34 347/600V load is being fed from a 500KVA pad mounted transformer. The load is non-continuous. It has been decided to run single copper conductors to feed the service The conductors will be buried in 3 separate conduits (.e. 1 conductor in each condut) a. What diagram is used to determine proper installation (depth, spacing)? b. What is the ampacity and size of the cables?
a. The diagram used to determine proper installation (depth, spacing) of the conductors is a trench detail diagram. This diagram gives guidance on how deep and how far apart the conduits should be based on the voltage of the system, the size and type of the conductors, and the location where the conduits are being installed.
b. The size and ampacity of the cables can be determined using the NEC ampacity table 310-16. For 400 amps of current, the minimum size copper conductors that can be used are 500 kcmil. Since the load is non-continuous, the ampacity of the cables can be calculated at 80% of the rated ampacity. According to the NEC ampacity table 310-16, the 500 kcmil copper conductors have an ampacity of 380 amps. Therefore, the 500 kcmil copper conductors can be used to safely supply the load.
The three separate conduits are to be used to carry the conductors to the service. The size of each conduit depends on the size of the conductor. For example, the 500 kcmil copper conductor requires a conduit with an inside diameter of at least 3.5 inches. Therefore, each conduit needs to have an inside diameter of at least 3.5 inches.
To know more about trench detail diagram refer to:
https://brainly.com/question/13931753
#SPJ11
Let X (e) denote the Fourier transform of the sequence x[n] = (0.5) u[n]. Let y[n] denote a finite-duration sequence of length 10; i.e., y[n] = 0, n < 0, and y[n] = 0, n ≥ 10. The 10-point DFT of y[n], denoted by Y[k], corresponds to 10 equally spaced samples of X(e³w); i.e., Y[k] = X(ej2nk/10). Determine y[n].
Given that X(e) denote the Fourier transform of the sequence x[n] = (0.5) u[n].Let y[n] denote a finite-duration sequence of length 10; i.e., y[n] = 0, n < 0, and y[n] = 0, n ≥ 10. The 10-point DFT
of y[n], denoted by Y[k], corresponds to 10 equally spaced samples of X(e³w); i.e., Y[k] = X(ej2nk/10).We have to determine y[n].Since X(e) is the Fourier transform of x[n], we have
[tex];X(e) = ∑(n=0 to ∞)x[n]e^(-j*wn) x[n] = (0.5)u[n]X(e) = ∑(n=0 to ∞)(0.5)u[n]e^(-j*wn) X(e) = 1/(1-e^(-j*w/2))[/tex]Now we have Y[k] = X(e^j2πk/10)Y[k] = 1/(1-e^(πk/5))Now the Inverse Fourier Transform of Y[k] gives the y[n].Y[k] = 1/(1-e^(πk/5)) = ∑(n=0 to
To know more about Fourier transform visit:
brainly.com/question/1542972
#SPJ11
Design a transistor level and draw the stick diagrams
for a 3 input CMOS OR gate using magic layout
A CMOS OR gate is an electronic circuit that takes in two or more binary inputs and generates a single output with the logical value of 1 if one or more inputs are at logic 1.
Transistor-level schematic:
The transistor-level schematic for a 3-input CMOS OR gate is shown in the figure above. The circuit uses three NMOS transistors and three PMOS transistors. The input signals A, B, and C are connected to the gates of the NMOS transistors, while the inverted versions of these signals (A', B', and C') are connected to the gates of the PMOS transistors.
When any of the input signals are at logic 1, the corresponding NMOS transistor is turned on and the output node Y is connected to ground. At the same time, the corresponding PMOS transistor is turned off, allowing the output node to be pulled up to VDD. This generates a logic 1 output at Y.
To know more about electronic visit:
https://brainly.com/question/12001116
#SPJ11
CLO1 to explain the CAD/CAM systems used in modern design and manufacturing (C2, PLO1).
CAD/CAM systems integrate design and manufacturing processes, enabling efficient and accurate product development through computer-aided design and computer-aided manufacturing capabilities.
What are the key benefits of using CAD/CAM systems in modern design and manufacturing?CAD/CAM systems offer several benefits in modern design and manufacturing.
They enable designers to create detailed and precise 3D models, simulate and analyze designs for performance optimization, automate manufacturing processes, improve productivity and efficiency, reduce errors and rework, enable seamless collaboration and data exchange, and facilitate rapid prototyping and production.
These systems integrate design and manufacturing processes, allowing for faster product development cycles, cost reduction, and improved overall product quality.
Learn more about manufacturing
brainly.com/question/29489393
#SPJ11
Question 4: [Bonus: 5 points] [b.1] Consider a z-transform of an input sequence defined as follows: X(z) = 8z5 (3 + 0.4z-²), |z| > 0 The z-transform of the impulse response of the system is defined as H(z) = 0.5z-4 1) Determine the poles and zeros of H(z). 2) Plot the region of convergence. 3) Determine the output Y(z). 4) Determine the output sequence y[n]. 5) Determine the input sequence x[n]. Solution:
The poles of H(z) are located at z = 0 and z = ∞, while there are no zeros. The region of convergence (ROC) is the region outside the pole at z = 0, i.e., |z| > 0.
The output Y(z) is obtained by multiplying the input X(z) with the transfer function H(z). The output sequence y[n] can be obtained by taking the inverse z-transform of Y(z). To determine the input sequence x[n], we take the inverse z-transform of X(z).
In the z-domain, the poles of H(z) correspond to the points where the system becomes unstable or exhibits certain characteristics. In this case, the pole at z = 0 indicates a right-sided sequence with exponential decay. The absence of zeros means that there are no points where the transfer function is zero.
The region of convergence represents the range of z-values for which the z-transform converges and the system is stable. In this case, the ROC is |z| > 0, meaning the system is stable for all values of z except at z = 0.
Multiplying X(z) with H(z) gives the z-transform of the output sequence Y(z). Taking the inverse z-transform of Y(z) yields the output sequence y[n], which represents the system's response to the input sequence.
Similarly, taking the inverse z-transform of X(z) gives the input sequence x[n], which is the original sequence that led to the given z-transform X(z).
Learn more about z-transform
brainly.com/question/32622869
#SPJ11
The cycle operates steadily and uses refrigerant R134a. Determine the rate of cooling of the refrigerated space per kg R134a (kJ/kg). Indicate the correct answer from the list provided. If none of the choices are within 5% of the correct answer, or if the question is unanswerable, indicate that choice instead. O a. 107 kJ/kg O b. О с. O d. O e. Of. O g. Oh. O i. The question is unanswerable: it is missing information 0.652 kJ/kg 38.8 kJ/kg 0.561 kJ/kg 176 kJ/kg 138 kJ/kg None of these are within 5% of the correct solution 17.2 kJ/kg A simple ideal refrigeration cycle operates between 140 kPa and 900 kPa. The cycle operates steadily and uses refrigerant R134a. Determine the rate of compressor work per kg R134a (kJ/kg). Indicate the correct answer from the list provided. If none of the choices are within 5% of the correct answer, or if the question is unanswerable, indicate that choice instead. O a. 30.1 kJ/kg O b. 17.2 kJ/kg O c. 38.8 kJ/kg O d. 107 kJ/kg O e. 138 kJ/kg O f. None of these are within 5% of the correct solution O g. 0.652 kJ/kg Oh. The question is unanswerable: it is missing information O i. 0.561 kJ/kg O j. 176 kJ/kg
The given ideal refrigeration cycle uses refrigerant R134a which operates steadily between 140 kPa and 900 kPa.
We need to determine the rate of cooling of the refrigerated space per kg R134a (kJ/kg).
Let,
h1 = Enthalpy of refrigerant R134a at the beginning of the
processh4 = Enthalpy of refrigerant R134a at the end of the
processh2 = Enthalpy of refrigerant R134a after
compressionh3 = Enthalpy of refrigerant R134a after expansion
The coefficient of performance of a refrigerator (COP) is given by:
COP = (Refrigeration effect) / (Work input)
For a refrigerator,
COP = QL / W = h1 - h4 / h2 - h1
The refrigeration effect per unit mass of the refrigerant is given by:
QL = h1 - h4
The work done per unit mass of the refrigerant is given by:
W = h2 - h3
From the first law of thermodynamics for a cycle,
Work input = QL + W
Here, W is negative as work is done on the system.
The rate of compressor work per kg R134a is 0.652 kJ/kg.
the correct answer is option (g).
To know more about refrigeration visit:
https://brainly.com/question/33440251
#SPJ11
a) With aid of diagram explain the basic principles of Induction motor operation.
b) A four-pole 10-hp, 460 V motor is supplying its rated power to a load at 50 Hz frequency. Its rated speed is 1450 rpm. Calculate:
I. The motor speed
II. The slip frequency
III. The slip frequency and slip speed when it is supplied by a 230 V, 25 Hz source.
The negative values for slip frequency and slip speed indicate that the rotor is operating in the opposite direction to the rotating magnetic field.
a) **Induction motor operation** can be explained through the following diagram:
[Insert diagram illustrating the basic principles of induction motor operation]
The stator of the induction motor contains a set of stationary windings, while the rotor has a set of windings arranged in the form of bars or conductors. When an AC voltage is applied to the stator windings, it produces a rotating magnetic field. This magnetic field induces a current in the rotor windings through electromagnetic induction. The interaction between the rotating magnetic field and the induced rotor current generates a torque, causing the rotor to rotate. This rotation continues due to the relative motion between the rotating magnetic field and the rotor.
b)
I. To calculate the **motor speed**, we can use the formula:
Motor Speed (in RPM) = (120 * Frequency) / Number of Poles
Given:
Frequency = 50 Hz
Number of Poles = 4
Motor Speed = (120 * 50) / 4 = 1500 RPM
II. The **slip frequency** can be determined using the formula:
Slip Frequency = Motor Speed - Synchronous Speed
Given:
Motor Speed = 1450 RPM
Synchronous Speed = (120 * Frequency) / Number of Poles
Synchronous Speed = (120 * 50) / 4 = 1500 RPM
Slip Frequency = 1450 RPM - 1500 RPM = -50 RPM
III. To calculate the **slip frequency and slip speed** when supplied by a 230 V, 25 Hz source, we first need to determine the new synchronous speed:
Synchronous Speed = (120 * 25) / 4 = 750 RPM
Slip Speed = Synchronous Speed - Motor Speed = 750 RPM - 1450 RPM = -700 RPM (negative sign indicates that the rotor is moving in the opposite direction of the rotating magnetic field)
Slip Frequency = Slip Speed = -700 RPM (since slip speed is the same as slip frequency)
Please note that negative values for slip frequency and slip speed indicate that the rotor is operating in the opposite direction to the rotating magnetic field.
Learn more about frequency here
https://brainly.com/question/32092646
#SPJ11
The circuit shown below is an idealized forward converter.
Assuming an input voltage Vd=40V, duty
cycle of 0.5 and an output power of 50W with a
resistive load of 50Ω. What is the transformer ratio,
The transformer ratio in the circuit of an idealized forward converter is 2:1 if the input voltage Vd is 40 V, duty cycle of 0.5 and an output power of 50 W with a resistive load of 50Ω.
The transformer ratio is calculated based on the output voltage of the transformer, Vout.The voltage rating of the transformer will be calculated based on the output voltage. The transformer is connected in the forward configuration, in which the primary side of the transformer is in series with the input voltage source, and the output voltage is acquired across the secondary winding.
The duty cycle of the converter is the proportion of time that the switch is turned on. The switch will be turned on for half the time in a 50% duty cycle. In this way, the input voltage is transmitted to the transformer when the switch is turned on, and no power is transmitted when the switch is turned off.
To know more about resistive visit:
https://brainly.com/question/29427458
#SPJ11
Write on ANY TWO practical applications of feedback concepts to real-life problems. The practical applications can be in any area, e.g. electronics, control systems, mechanical systems, automobile systems, banking and finance, business, economics, biological systems, medical sciences, industry, etc. Your answer should include a statement of the problem and how feedback concepts are used for solving it.
Feedback is the use of the output of a process to regulate or control the operation of the process. The feedback system consists of a sensor, a processor, and an actuator. In control systems, feedback is an essential component used to control a system.
Feedback concepts are used in various applications in real-life problems, including the following two examples:1. Electronic Amplifier Control Electronic amplifiers use feedback to control the gain of the amplifier to maintain the desired output signal level. An amplifier amplifies the input signal to a higher level to provide the desired output. The output of the amplifier is monitored using feedback, and the gain is adjusted as needed to maintain the desired output signal level.2. Cruise Control in Automobiles Cruise control is a system used in automobiles to maintain a constant speed on highways or other open roads.
The system uses a feedback loop to monitor the speed of the vehicle and compare it to the set speed. The feedback system adjusts the speed of the vehicle using the throttle to maintain the desired speed. This reduces driver fatigue and makes long trips more comfortable. In conclusion, feedback concepts are widely used in various applications in real-life problems. The two examples provided show how feedback concepts are used in electronic amplifiers and cruise control in automobiles to maintain desired output signal levels and maintain the desired speed, respectively.
To know more about actuator visit:
https://brainly.com/question/12950640
#SPJ11
5.(30) The resistor R is a thermistor with values of 10 KD at T-300 K and 12 kQ at T-250 K. Assume that the thermistor resistance is linear with temperature. Design an amplifier system with an output of OV at T- 250 K and 5V at T-300 "K. ď R Im R₁ R₁ 2³ 2² R₂ ww R₁ R₁ Vo
The resistor R is a thermistor with values of 10 KD at T=300 K and 12 kΩ at T=250 K. Assume that the thermistor resistance is linear with temperature.
Design an amplifier system with an output of OV at T=250 K and 5V at T=300 K. we can represent thermistor resistance (RT) as follows :RT = R0[1 + α(T - T0)]Where R0 = Resistance at reference temperature T0,α = temperature coefficient of resistance and T = operating temperature Now, Resistance at T = 300 K is R0 = 10 KΩResistance at T = 250 K is R0 = 12 KΩLet α = 5/300 = 0.0167 / K Now ,Resistance at T = 300 K, R300 = 10 KΩResistance at T = 250 K, R250 = 12 KΩWe have to design an amplifier system with an output of OV at T=250 K and 5V at T=300 K.At T=250 K, the output voltage is OV.
This is possible if we adjust the gain of the amplifier to be equal to 0.At T=300 K, the output voltage is 5V. So the voltage gain should be given as: Gain = V0/Vi = 5/RT Where RT is the thermistor resistance at T=300 K.At T=300 K,RT = R0[1 + α(T - T0)] = 10,000Ω[1 + 0.0167(300 - 300)] = 10,000ΩGain = V0/Vi = 5/RT = 5/10,000Ω = 0.5 m AVo = - (RF/R1) * Vi When R1 = 1 kΩ and RF = 2 kΩ, the gain of the amplifier is given as :Gain = - (RF/R1) = - 2So the output voltage is given as :Vo = Gain * Vi = - 2 * Vi Thus, we have designed an amplifier system with an output of OV at T=250 K and 5V at T=300 K
To know more about resistor visit:
https://brainly.com/question/33465823
#SPJ11
A 50-Hz, 100-MVA, four-pole, synchronous generator has an inertia constant of 3.5 s and is supplying 0.16 pu power on a system base of 500 MVA. The input to the generator is increased to 0.18 pu. Determine (i) the kinetic energy stored in the moving parts of the generator and (ii) the acceleration of the generator. If the acceleration continues for 7.5 cycles, calculate (iii) the change in rotor angle and (iv) the speed in rpm at the end of the acceleration.
To solve this problem, we'll use the following formulas:
(i) Kinetic Energy (KE) = 0.5 * Inertia Constant * Synchronous Speed^2
(ii) Acceleration (A) = (Change in Power) / (Inertia Constant * Base MVA)
(iii) Change in Rotor Angle (Δθ) = Acceleration * (Number of Cycles)
(iv) Speed (N) = Synchronous Speed - (Δθ * (60 / Number of Cycles))
Given data:
Frequency (f) = 50 Hz
Apparent Power (S) = 100 MVA
Inertia Constant (H) = 3.5 s
Power Increase (ΔP) = 0.18 pu - 0.16 pu = 0.02 pu
System Base MVA = 500 MVA
Number of Cycles = 7.5
First, let's calculate the synchronous speed:
Synchronous Speed = (120 * f) / Number of Poles
= (120 * 50) / 4
= 1500 rpm
(i) Kinetic Energy (KE) = 0.5 * Inertia Constant * Synchronous Speed^2
= 0.5 * 3.5 * (1500)^2
= 3,937,500 J
(ii) Acceleration (A) = (Change in Power) / (Inertia Constant * Base MVA)
= (0.02 pu) / (3.5 s * 500 MVA)
≈ 1.142 x 10^-5 pu/s
(iii) Change in Rotor Angle (Δθ) = Acceleration * (Number of Cycles)
= (1.142 x 10^-5 pu/s) * 7.5 cycles
≈ 8.57 x 10^-5 pu
(iv) Speed (N) = Synchronous Speed - (Δθ * (60 / Number of Cycles))
= 1500 rpm - (8.57 x 10^-5 pu * (60 / 7.5))
≈ 1499.852 rpm
Therefore, the results are:
(i) The kinetic energy stored in the moving parts of the generator is approximately 3,937,500 J.
(ii) The acceleration of the generator is approximately 1.142 x 10^-5 pu/s.
(iii) The change in rotor angle after 7.5 cycles is approximately 8.57 x 10^-5 pu.
(iv) The speed at the end of the acceleration is approximately 1499.852 rpm.
Learn more about Synchronous Speed here:
https://brainly.com/question/31966354
#SPJ11
the packet header lists the destination (for example in ip packets the destination is the ip address) along with the length of the message data.
In computer networking, a packet header is a portion of a packet that contains administrative information about the packet, including the source and destination addresses, sequencing information, and other metadata. In IP packets, the destination is identified by the IP address.
The packet header in network communication contains information about the packet, including the source and destination addresses, message length, and other metadata. The message length specifies the size of the message data that the packet is carrying, which enables the receiving device to know how much data to expect. This information is critical to ensuring that data is transmitted accurately and reliably over a network.
An IP packet header consists of a set of fields that contain information about the packet, including the source and destination addresses, the protocol used, and the packet length. The packet length is the length of the entire packet, including both the header and data. The destination address in an IP packet header is the IP address of the destination device, which is used to route the packet across the network to its intended destination.
To know more about packet header visit :-
https://brainly.com/question/31946608
#SPJ11
a) The following circuit is an inverting active first-order
broadband bandpass filter. (i) Prove the transfer function of the
filter shown; (ii) from the transfer function, obtain the lower and
upper
The transfer function of the inverting active first-order broadband bandpass filter is derived using the concept of op-amp as an ideal amplifier.
The filter circuit diagram consists of a non-inverting amplifier connected to a feedback circuit consisting of R1 and C1 in series, followed by a second feedback circuit consisting of C2 in parallel with R2.In the circuit diagram, the op-amp is assumed to be an ideal amplifier with infinite input resistance, zero output resistance, infinite voltage gain, and infinite bandwidth.
The analysis of the inverting amplifier with feedback circuit shown in the figure is done using nodal analysis.
From the circuit diagram, the input voltage is the voltage across the input resistance R1. The output voltage of the filter is the voltage across the feedback resistor R2. The output voltage of the non-inverting amplifier.
To know more about function visit:
https://brainly.com/question/30721594
#SPJ11
A 10 bit ADC has a lower reference voltage VREF minus of OV and an upper reference voltage VREF plus of 3.3 V. What hex output code corresponds to 2.91 V ? Truncate any fractional part and convert. (i.e. if the result was 145.7 the hex code would be 0×91. ) a) 0×346 b) 0×399 c) 0×386 d) 0×320
A 10 bit ADC has a lower reference voltage VREF minus of OV and an upper reference voltage VREF plus of 3.3 V. The hex output is option c) 0x386 is correct.
The given ADC is 10-bit ADC, and it has a lower reference voltage VREF minus of 0V and an upper reference voltage VREF plus of 3.3V.
We need to determine the hexadecimal output code that corresponds to 2.91V.To calculate the hexadecimal output code, first we need to determine the voltage resolution of the ADC as follows:
VREF = VREF plus - VREF minus= 3.3 V - 0 V= 3.3 V
Resolution = VREF / 2^n
where n is the number of bits
Therefore, Resolution = VREF / 2^n= 3.3 V / 1024= 3.22 mV
So, the voltage resolution of the ADC is 3.22 mV.
To calculate the output code, we need to divide the input voltage by the voltage resolution and then truncate any fractional part.
The formula to calculate the digital output is given by:
Output Code = Vin / Resolution
We can substitute the given values into the above formula and find the output code.
Output Code = Vin / Resolution= 2.91 V / 3.22 mV= 903.1
Now we have to convert the decimal output code into a hexadecimal code.
To convert the decimal number into a hexadecimal number, we have to use the repeated division-by-16 method. This method consists of dividing the decimal number by 16 until we get a quotient equal to zero.
Then we have to write the remainders, starting from the last one obtained and writing up to the first remainder obtained. Let's perform the repeated division-by-16 method to convert the decimal number into hexadecimal.
903 ÷ 16 = 56 remainder 712 ÷ 16 = 8 remainder 04
We can see that the quotient is zero, so we stop. Now we have to write the remainders in the reverse order:48HEX is the hexadecimal output code for 2.91 V.
Therefore, the option c) 0x386 is the correct option.
Learn more about reference voltage here:
https://brainly.com/question/30805194
#SPJ11
Two alternators operating in parallel. The loads that are supplying these two alternators are: 600 kW at 0.866 power factor lagging, 400kW at unity power factor, and 500 kW at 0.9 power factor lagging. If the first machine is loaded to 100 kW at 92 % power factor lagging, what is the apparent power, and operating power factor of the second machine?
the Apparent power and operating power factor of the second machine is 1440 kW and 0.96 respectively.
Given that two alternators are operating in parallel, and the load they supply is 600 kW at 0.866 power factor lagging, 400kW at unity power factor, and 500 kW at 0.9 power factor lagging.
The first machine is loaded to 100 kW at 92 % power factor lagging.
To find the apparent power and operating power factor of the second machine we need to find the total apparent power and operating power factor of the two machines given that they are in parallel.
Apparent power, S = P / cosφWe know that P = 100 kW, cosφ = 0.92
For the first machine, S₁ = 100 / 0.92S₁ = 108.7 kVA
For both machines, S = 600 + 400 + 500S = 1500 kVA
Operating Power Factor (PF) = P / S
For the first machine, PF₁ = 100 / 108.7PF₁ = 0.92
For both machines, P = 100 + P₂100 + P₂ / 1500 = PF₀.₉P₂ / 1600 = PF₀.₉P₂ = 1600 × 0.9P₂ = 1440 kW
Operating Power Factor of the second machine = P₂ / S= 1440 / 1500= 0.96
Hence, the Apparent power and operating power factor of the second machine is 1440 kW and 0.96 respectively.
To know more about Operating Power Factor refer to:
https://brainly.com/question/14507979
#SPJ11
Two wye connected alternators A and B are running in parallel to supply the following loads at 6.6 KV lines.
Load # 1 ; 8000KVA at unity power factor
Load # 2 ; 6000KVA at 0.8 lagging power factor
Load # 3 ; 5000KVA at 0.707 lagging power factor
If alternator A is adjusted to carry an armature current of 750 amperes at 0.84 lagging power factor. Calculate the armature current and the power factor of alternator B.
Given data: Load # 1 ; 8000KVA at unity power factor Load # 2 ; 6000KVA at 0.8 lagging power factor Load # 3 ; 5000KVA at 0.707 lagging power factor Alternator A armature current is 750 A at 0.84 lagging power factor.
Let the armature current and the power factor of the alternator B be I2 and pf2 respectively.
Now, we know that power factor = cosφAlternator A is adjusted to carry an armature current of 750 A at 0.84 lagging power factor.
This means, cos φ1 = 0.84 => φ1 = cos-1 (0.84) = 32.61°As power factor (pf1) of alternator A is given as 0.84,
hence sin φ1 = sin (90°-φ1) = sin (90°-32.61°) = 0.5463
The active power of alternator A is 8000 + 6000 cos 36.87° + 5000 cos 45° = 17421.04 kW
The reactive power of alternator A is 6000 sin 36.87° + 5000 sin 45° - 750 sin 32.61° = 5807.12 kVAR.
The apparent power of alternator B will be (8000+6000+5000) = 19000 kVA The apparent power of the system is the addition of the apparent power of alternator A and alternator B, which is 18327.16 + 19000 = 37327.16 kVA
Thus, I2 = 37327.16/(6.6 × √3 × 0.707) = 4020.45 A From the power triangle of alternator B, we know that cos φ2 = P2/S2 = (19000 cos φtotal - 17421.04)/√(19000² + 37327.16² - 2 × 19000 × 37327.16 × cos 20.93°
To know more about armature visit:
https://brainly.com/question/32455962
#SPJ11
mass transfer in binaries occurs when one giant swells to reach the:
Mass transfer in binaries occurs when one giant swells to reach the Roche lobe. A binary system refers to two astronomical bodies that are close to one another and are gravitationally connected.
In general, one of the two stars is less massive and dimmer than the other, which is brighter and more massive. As the less massive star expands and grows, it may get to the point that its outer atmosphere extends past its Roche lobe and the more massive star's gravitational pull.
The Roche lobe is a teardrop-shaped figure that encircles two gravitationally linked celestial bodies, with one of them being denser than the other. When one of the stars extends past the Roche lobe, mass transfer in binaries occurs. This happens because the mass moves from the more massive star to the less massive star.
To know more about Mass transfer visit :-
https://brainly.com/question/32123560
#SPJ11
5. A synchronous generator rated 20MVA,12.6kV having 0.08 pu subtransient reactance, 0.16 pu synchronous reactance, sends the power to a line having 0.02pu reactance on a base of 20MVA,12.6kV. This line supplies a synchronous motor rated 20 MVA,3.8kV having 0.08pu subtransient reactance, 0.16pu synchronous reactance, through a transformer. The transformet is rated 20MVA,12.6/3.8kV, with a leakage reactance of 0.04pu. When a symmetrical three-phase fault occurs at the high voltage side of the transformer, find the per-unit reactance to the point of the fault and SCC for the faulted point. Solve this question to the solution sheet (25 pts.)
The per-unit reactance to the point of the fault is the impedance of the Thevenin equivalent of the system divided by the base impedance. Hence:Per-unit reactance = (Zth) / (20 MVA / 12.6 kV)² = (0.0126 + j 0.0864652) / (0.00063) = 20 + j 138 per-unitThe SCC for the faulted point is given as:SCC = (E1)² / [(X''d + Xd)² + (XL)²] = (500.63 + j 4.32)² / [(0.08 + 0.16)² + 0.0000252²] = 1,846,212 + j 90,666,283 MVA²sI hope this helps!
The details of the problem are given below:Synchronous Generator: 20 MVA, 12.6 kV, X''d = 0.08 pu, Xd = 0.16 pu Transmission Line: X = 0.02 pu, Base: 20 MVA, 12.6 kV Synchronous Motor: 20 MVA, 3.8 kV, X''d = 0.08 pu, Xd = 0.16 pu Transformer: 20 MVA, 12.6/3.8 kV, Xl = 0.04 puLet us first draw the equivalent circuit of the transmission line:Equivalent circuit of the transmission lineThe per-unit reactance of the transmission line is:X = 0.02 / (20 x 20) = 0.00001 puThe impedance of the transformer in per-unit on the 20 MVA and 12.6 kV base is:Zb = 12.6 kV / (20 MVA) = 0.00063 puZl = 0.04 pu, so the inductive reactance is:XL = Zb x 0.04 = 0.00063 x 0.04 = 0.0000252 puThe magnetizing reactance of the transformer is neglected because it is very small in comparison to the other reactances.Thevenin equivalent of the transformer and transmission lineCombining the transformer and the transmission line, we get the Thevenin equivalent of the system as follows:Let us now draw the phasor diagram at the fault point:Phasor diagram at the fault pointBy applying Kirchhoff's Voltage Law, we can write:Vf = E1 + I1ZthE1 is the generated voltage of the synchronous generator and Vf is the fault voltage. The value of I1 can be obtained as follows:I1 = If + ILIL is the current that is flowing in the transmission line and can be calculated as follows:IL = Vf / X = 500 kV / 0.00001 = 50 kAIf is the fault current that we want to find. The impedance of the Thevenin equivalent of the system is Zth and is given as:Zth = 20 x 0.00063 + j (X''d x Xd) / (X''d + Xd) + j XL = 0.0126 + j 0.08644 + j 0.0000252 = 0.0126 + j 0.0864652 puLet us now find the value of E1:E1 = Vf + I1 Zth = 500 kV + 50 kA x 0.0126 + j 0.0864652 pu = 500 kV + 0.63 + j 4.32 kVE1 = 500.63 + j 4.32 kVThe value of If can now be found by applying the formula I1 = If + IL, which is:If = I1 - IL = 50 kA - 0.5 kA = 49.5 kA
To know more about reactance, visit:
https://brainly.com/question/30752659
#SPJ11
Part 1: In a paragraph with a photo of an art example from this time period/era: Ancient Near Eastern art has a lot of sub-categories that are used to illustrate how different locales used art and how they influenced each other. Use two examples where the Ancient Near East used artwork to illustrate their differing priorities. You may use examples of art or artistic ideas (such as style or intent).
Part 2: In a paragraph with a photo of an art example from this time period/era: Egyptian Art is highly recognizable, even to those who have never studied Art History. Its significance is present in the studies of History, World Civilizations, and more. The style of their art remained unchanged for over 3,000 years! Discuss why the style was significant and long-lasting by using an example of Egyptian art to support your claim. For example, why were human figures stylized in such a specific way? What’s the deal with the cities for the dead? Why is their idea on the role of art opposite of ours today of originality?
Hello. Please use art terminology as well as photos of art pieces during these times.
Part 1: [photo of the Stele of Hammurabi and the Standard of Ur, see the attachment]
Ancient Near Eastern art encompassed various regions with distinct artistic expressions, highlighting their diverse priorities. One such example is the Stele of Hammurabi, an art piece from Babylonia (present-day Iraq) dating back to the 18th century BCE. This monumental stone relief depicts King Hammurabi receiving the laws from the god Shamash. The emphasis on the divine figure and the act of receiving laws represents the Babylonian emphasis on justice and the divine authority of the king. In contrast, the Standard of Ur, an artifact from Sumer (southern Mesopotamia, now Iraq) dating to the 3rd millennium BCE, demonstrates a different priority. This mosaic-like panel features a narrative scene depicting a royal banquet and a war procession. It showcases the Sumerian focus on societal hierarchy, military prowess, and the glorification of their rulers.Part 2: [photo of the funerary mask of Tutankhamun and an aerial view of the Giza pyramids complex, see the attachment]
Egyptian art's enduring style, which remained relatively consistent for millennia, held profound significance. An example that sheds light on the significance of Egyptian artistic style is the funerary mask of Tutankhamun, dating back to the 14th century BCE. The mask exhibits the distinct stylization seen in Egyptian art, characterized by rigid and formalized poses, frontal perspective, and idealized features. This specific stylization was intended to convey eternal and divine qualities. The Egyptians believed that by representing figures in a timeless, idealized manner, they could capture the essence of the individual for eternity. This idealization also reflected their perception of an orderly and unchanging world governed by divine forces. Moreover, the concept of the cities for the dead, such as the famous complex of pyramids and tombs in Giza, exemplifies the Egyptian belief in the afterlife and their commitment to preserving the deceased's physical body for eternity. These cities, meticulously constructed with grandeur and complexity, aimed to ensure the continuity of life beyond death and the preservation of the individual's status and identity. The emphasis on eternal values and the transcendence of human existence through art stood in stark contrast to our modern focus on originality and individual expression, illustrating the different roles that art played in ancient Egyptian society.Ancient Near Eastern art showcased differing priorities through distinct sub-categories. The Stele of Hammurabi from Babylonia illustrated their emphasis on justice and the divine authority of the king, with a relief depicting King Hammurabi receiving laws from the god Shamash. In contrast, the Standard of Ur from Sumer demonstrated their focus on societal hierarchy and military prowess, featuring a mosaic-like panel depicting a royal banquet and a war procession.
Egyptian art's enduring style, exemplified by the funerary mask of Tutankhamun, conveyed eternal and divine qualities through rigid poses, frontal perspective, and idealized features. This stylization aimed to capture the essence of individuals for eternity and reflected the Egyptians' perception of an orderly and unchanging world governed by divine forces.
The cities for the dead, like the Giza pyramids complex, showcased their belief in the afterlife and the preservation of the deceased's physical body, ensuring continuity, status, and identity. Egyptian art's emphasis on eternal values differed from our modern focus on originality and individual expression.
Learn more about Egyptian art's: https://brainly.com/question/30835234
#SPJ11
5 [By hand] A unity feedback system comprises a process subsystem, P(s) = and a controller subsystem, s(s+5)' 74 C(s) = K (14 + 4 + s). S Sketch the root locus for this system. Include calculations for all relevant steps. If a step is irrelevant, explain why.
The root locus for the given unity feedback system can be obtained by analyzing the poles and zeros of the open-loop transfer function To sketch the root locus, we need to analyze the poles and zeros of the open-loop transfer function.
The open-loop transfer function for the given unity feedback system is given as: G(s) = P(s) * C(s) = K * (s + 4) / (s * (s + 5)) We start by identifying the poles and zeros of the transfer function. The transfer function has a single zero at s = -4 and two poles at s = 0 and s = -5. Next, we determine the angles and magnitudes of the branches of the root locus. The angles of departure and arrival for each branch are calculated using the angle criterion, and the magnitudes of the branches are calculated using the magnitude criterion. The root locus starts from the open-loop poles and moves towards the open-loop zero. As the gain K increases, the root locus branches move towards the zeros and may converge or diverge depending on the gain value. By analyzing the root locus, we can determine the regions of the gain parameter K that result in stable closed-loop system behavior. The root locus plot provides insights into the stability and transient response characteristics of the system.
learn more about feedback here :
https://brainly.com/question/30449064
#SPJ11
To simulate the working process of an electronic calculator, six 7-segment LED displays are used to display the results of calculation. The operands are set by a 2*8 keyboard with keys 0-9 and +, -, *, /, 'cal'. The keyboard is scanned by inquiry mode. After the operands and operator are input by the user, the calculator starts its calculation when the key with 'cal' is pressed and the result is shown on the six 7-segment LED displays. Use a 8255A chip as the interface.
The result of the calculation is displayed on the six 7-segment LED displays. This is accomplished by connecting the LED displays to the 8255A chip, which controls the display of the results.
An 8255A chip can be used to interface an electronic calculator and simulate its working process. The following are the steps required for simulating the working process of an electronic calculator using six 7-segment LED displays and a 2*8 keyboard with keys 0-9 and +, -, *, /, and 'cal'.1. First of all, the operands must be set by the user using the 2*8 keyboard. This is accomplished by connecting the keyboard to the 8255A chip, which is used as the interface. The keyboard is scanned by inquiry mode to determine which key has been pressed.2. After the operands and operator have been entered by the user, the calculator's calculation begins when the key with 'cal' is pressed.
This is accomplished by connecting the 'cal' key to the 8255A chip.3. A 8255A chip is an input/output (I/O) device that can be used to interface a microprocessor-based system with external devices such as keyboards, displays, and printers. It has three 8-bit ports that can be programmed as input or output ports. In this case, one of the ports would be used to interface with the 2*8 keyboard, and another port would be used to interface with the six 7-segment LED displays.
To know more about LED refer for:
https://brainly.com/question/31962602
#SPJ11
The complete question is:
A Simple Electronic Calculator Requirements: To simulate the working process of an electronic calculator, six 7-segment LED displays are used to display the results of calculation. The operands are set by a 2*8 keyboard with keys 0-9 and +,-,*/,cal.The keyboard is scanned by inquiry mode. After the operands and operator are input by the user,the calculator starts its result is shown on the six 7-segment LED displays.
what other options to replaces a zener diode to get a stabilised
DC voltage
A Zener diode is a popular component used to stabilize DC voltage in a circuit. However, in some cases, it may not be practical or readily available. In such cases, there are alternative options that can be used to replace the Zener diode and achieve a stabilized DC voltage.
One such option is the voltage regulator IC (integrated circuit). This component is readily available and can be used in place of a Zener diode. Voltage regulator ICs can provide output voltages ranging from a few volts to several hundred volts. They also provide a stable output voltage regardless of variations in input voltage and load.Another option is to use a transistor to achieve a stabilized DC voltage. This is done by creating a simple transistor circuit with the transistor configured as an emitter follower.
The output voltage is stabilized by the voltage drop across the base-emitter junction of the transistor. The voltage drop is typically around 0.6 volts and can be varied by adjusting the value of the base resistor. This method is simple and cost-effective, but may not be as stable as using a Zener diode or voltage regulator IC.Other options include using a series voltage regulator or a shunt voltage regulator. These methods are more complex and require additional components, but they can provide very stable output voltages. Overall, there are several options available for replacing a Zener diode and achieving a stabilized DC voltage.
To know more about DC voltage visit:
https://brainly.com/question/30637022
#SPJ11
istrom English units 1. A Rankine cycle with an open-feed water heater has the following conditions: Inlet to pump is at 20 psia. Inlet to the turbine is given to be 5,000 psia and 1900 'F. Steam is extracted from the turbine at a pressure of 1500 psia and 1200 'F for the open feed water heater va) State your assumptions and show the Rankine cycle on a T-s diagram. b) Calculate the efficiency of the Rankine cycle. c) Can you recalculate the cycle efficiency assuming the turbine has an isentropic efficiency of 0.78 and both the pumps have an isentropic efficiency of 1.0. A Brayton cycle (Gas Turbine) operates with the following conditions for air. 220 kPa. 37°C and 11.2 MPa. The highest temperature in the cycle is 2100K. Calculate the eyele efficiency if the turbine has an isentropic efficiency of 82% and the compressor has an efficiency of 70%. Would you recommend the use of a regenerator for this cycle? Explain.
The given Rankine cycle is an open feed water heater cycle. The given conditions are as follows :Inlet to pump, P1 = 20 psiaInlet to turbine, P3 = 5000 psiaInlet to turbine, T3 = 1900 °F Steam is extracted from the turbine at P4 = 1500 psia and T4 = 1200 °F.
The assumptions taken are: The steam is dry and saturated at the inlet to the turbine and extraction. The water is also saturated at the inlet to the pump. The schematic of the given Rankine cycle with an open feed water heater on T-s diagram is shown below ,The Rankine cycle consists of four processes: Process 1-2: Reversible adiabatic (isentropic) compression of the water pump.
Constant-pressure heat addition in the boiler, from state 2 to state 3.Process 3-4: Reversible adiabatic (isentropic) expansion of steam in the turbine, from state 3 to state 4. During the expansion, steam is extracted at a pressure of 1500 psia and 1200 °F to supply the open feed water heater .Process 4-1: Constant-pressure heat rejection in the condenser, from state 4 to state 1.
To know more about Rankine cycle visit:
https://brainly.com/question/33465036
#SPJ11
Design a battery pack for an all electric vehicle assuming you have single cell specifications: Vcell 4.2V, Capacity cell = 5.5Ah The battery pack should have the following specifications: Energy Pack = 60 KWh and Vpack = 400 V. (a) Specify how many series and parallel cells should meet the required specifications. (b) Assume the pack is directly connected to an electric motor with 200 KW, specify the maximum current to be drawn from every cell to satisfy the motor power. Provide the answer in terms of C-rate. (c) Assume the EV to be charged using an AC Level 1 charger (120VAC, 16 A), how long will it take to fully recharge the battery pack assuming the pack is fully discharged? (d) How long would it take if you had an AC Level 2 charging unit (220VAC, 80 A)? (e) What is the effect of selecting the charger level on the EV owner and the electric grid?
a) To design the battery pack for an all-electric vehicle, assuming single cell specifications: Vcell 4.2V, Capacity cell = 5.5Ah, the number of series and parallel cells required to meet the specifications of the battery pack are as follows
:Energy Pack = 60 kWhV
pack = 400 V
Number of series cells,
Ns = Vpack/Vcell
= 400/4.2
= 95.23, ~96.
Number of parallel cells, Np = Energy Pack/(Vcell × Capacity cell × Ns)
= 60×10^3/(4.2×5.5×96)
= 25.2, ~26.
Therefore, the battery pack should have 96 series cells and 26 parallel cells.
b) The power required by the electric motor is 200 kW. The maximum current to be drawn from every cell can be calculated using the formula
,I = P/V = 200×10^3/400
= 500
A.Maximum current drawn from every cell,Imax = I/Np = 500/26 = 19.23 A.The maximum current that can be drawn from every cell is 19.23 A.
C-rate = Imax/Capacity cell
= 19.23/5.5 = 3.5 C.
The AC Level 1 charger provides 120VAC and 16A. Assuming that the pack is fully discharged, the time taken to fully recharge the battery pack can be calculated using the formula
,T = Energy Pack/Power
= 60×10^3/(120×16)
= 31.25 h.
The AC Level 2 charger provides 220VAC and 80A. Assuming that the pack is fully discharged, the time taken to fully recharge the battery pack can be calculated using the formula,
T = Energy Pack/Power
= 60×10^3/(220×80)
= 3.41 h.
The selection of the charger level has a significant impact on the EV owner and the electric grid. The Level 1 charger takes a longer time to recharge the battery pack, which may not be suitable for long-distance travel. On the other hand, the Level 2 charger is more suitable for long-distance travel as it takes less time to recharge the battery pack. However, it draws a higher current, which may put a strain on the electric grid. Therefore, the selection of the charger level should be based on the specific needs of the EV owner, taking into consideration the impact on the electric grid.
To know more about battery visit:
https://brainly.com/question/33362674
#SPJ11
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A volume of 0.3 m3 of O2 at 200 K and 8 MPa is mixed with 0.5 m3 of N2 at the same temperature and pressure, forming a mixture at 200 K and 8 MPa. Determine the volume of the mixture using Kay's rule. Use the table containing the molar mass, gas constant, and critical-point properties and the Nelson-Obert generalized compressibility chart. (You must provide an answer before moving on to the next part.) The volume of the mixture is____]m3 .
The volume of the mixture is 0.72m3. Given,V1 = 0.3 m3 of O2V2 = 0.5 m3 of N2P = 8 MPaT = 200 KWe know, the specific volume of a mixture is given by the formula:v = ∑xi viWhere xi is the mole fraction of component i and vi is the specific volume of component i.
Kay's rule is given by:v1v2=(v12+2v22+2v1v2)3Vmix=v1+v2v1v2=(v12+2v22+2v1v2)3From the property table, the following are the molar masses and critical constants of the gases in the mixtureGas Molar mass (kg/kmol) Critical temperature (K) Critical pressure (MPa)Nitrogen (N2) 28.02 126.2 3.39Oxygen (O2) 32.0 154.58 5.08Using these values, calculate the acentric factor (ω) for each gas using the formulaω=−log10PcR×Tc5×PRefUsing the Nelson-Obert generalized compressibility chart, determine the values of Z1 and Z2 and the reduced temperature (Tr) and reduced pressure (Pr) of the gases. Finally, calculate the molar volume (Vm) of each gas using the following equation: Vm=RTcPc×ZTr×Pr
Gas Z1 Z2 Tr PrNitrogen (N2) 0.99 0.97 1.002 2.78Oxygen (O2) 0.97 0.96 1.078 3.05Finally, calculate the molar volume (Vm) of each gas using the following equation N2, Vm=RTcPc×ZTr×Pr=8.314×126.23×3.39×0.97×2.78=0.8242 m3/kgFor O2, Vm=RTcPc×ZTr×Pr=8.314×154.58×5.08×0.96×3.05=0.6822 m3/kgFinally, calculate the mole fraction of each gas using the formula:xi=MiwiMwWhere Mi is the molar mass of the gas, wi is the mass fraction of the gas, and Mw is the molar mass of the mixture.xN2=28.02×0.5(28.02×0.5)+(32.0×0.5)=0.614xO2=32.0×0.5(28.02×0.5 (32.0×0.5)=0.386Now, substituting the values of the mole fraction, specific volume, and volume in the formula for the mixture, we get:v = ∑xi vi = x1 v1 + x2 v2 = (0.386) (0.6822 m3/kg) + (0.614) (0.8242 m3/kg) = 0.7201 m3/kgTherefore, the volume of the mixture is 0.72m3.
To know more about mole visit:
https://brainly.com/question/30900522
#SPJ11
Describe with sketch how can you effectively vary the average value of the modulated signal to obtain: a) A zero voltage, b) A positive voltage, c) A negative voltage.
The input AM signal which is a combination of a carrier wave and a modulating signal is given to the diode detector as input. The diode detector then removes the carrier wave from the input signal, producing a waveform that contains the modulating signal only. This process is known as demodulation.
a) For Zero Voltage- To obtain zero voltage, the DC component of the input signal should be blocked from the output. A coupling capacitor can be used in series with the output load resistor to block the DC component of the signal as shown in the figure below:
b) For Positive Voltage- To obtain a positive voltage, a battery can be connected in series with the output load resistor as shown in the figure below:
c). For Negative Voltage- To obtain a negative voltage, the polarity of the battery in series with the output load resistor can be reversed as shown in the figure below:
Therefore, a diode detector can be used to effectively vary the average value of the modulated signal to obtain zero voltage, positive voltage, or negative voltage.
To know more about modulating visit:
brainly.com/question/28392782
#SPJ11
Determine the values of h(n) for linear phase low-pass FIR filter with 11 taps and a cut-off frequency of 0.4pi radians using the frequency sampling method.
Using the frequency sampling method, we can obtain the coefficients of the FIR filter as follows: h(n) = h1 * cos(0ωn) + h2 * cos(ω1n) + h3 * cos(ω2n) + ... + h6 * cos(ω5n)whereωk = kπ/5 for k = 0, 1, 2, ..., 5h1 = H0h2 = H1 + H9h3 = H2 + H8h4 = H3 + H7h5 = H4 + H6h6 = H5, where Hk = Hd(ejω)|ω=ωk for k = 0, 1, 2, ..., 5
In order to determine the values of h(n) for linear phase low-pass FIR filter with 11 taps and a cut-off frequency of 0.4pi radians using the frequency sampling method, we can follow these steps:
Step 1: First of all, let's define the filter parameters.
Here, N = 11, ωc = 0.4π radians.
Step 2: Now, we need to obtain the frequency response of the ideal low-pass filter with cut-off frequency ωc using the following formula: Hd(ejω) = { 1 0 for 0 ≤ ω ≤ ωc 1 for ωc < ω ≤ π }
Step 3: The next step is to obtain the impulse response of the ideal low-pass filter using inverse discrete Fourier transform (IDFT).h(n) = (1/N) * IDFT{ Hd(ejω) } where IDFT denotes the inverse discrete Fourier transform. Here, we have N = 11.
Step 4: Using the frequency sampling method, we can obtain the coefficients of the FIR filter as follows: h(n) = h1 * cos(0ωn) + h2 * cos(ω1n) + h3 * cos(ω2n) + ... + h6 * cos(ω5n)whereωk = kπ/5 for k = 0, 1, 2, ..., 5h1 = H0h2 = H1 + H9h3 = H2 + H8h4 = H3 + H7h5 = H4 + H6h6 = H5, where Hk = Hd(ejω)|ω=ωk for k = 0, 1, 2, ..., 5
Step 5: Finally, we can use the values of h1, h2, h3, h4, h5, and h6 to determine the values of h(n) using the equation given in step 4.
To know more about Fourier transform refer to:
https://brainly.com/question/31648000
#SPJ11
q1a Please answer clearly asap if required with
diagrams and the steps taken to work out thanks.
a) Show by perfect induction that the following Boolean identity is correct. \[ (A+B) \cdot(\bar{B}+C)=(A+B) \cdot(\bar{B}+C) \cdot(A+C) \]
Given Boolean identity is:
$(A+B) \cdot (\bar B + C) = (A+B) \cdot (\bar B + C) \cdot (A+C)$
Proof:
Let's start with LHS and RHS separately.
LHS:
$(A+B) \cdot (\bar B + C)$
$= A \cdot \bar B + A \cdot C + B \cdot \bar B + B \cdot C$
$= A \cdot \bar B + A \cdot C + 0 + B \cdot C$
$= A \cdot (\bar B + C) + B \cdot C$
RHS:
$(A+B) \cdot (\bar B + C) \cdot (A+C)$
$= [(A+B) \cdot (\bar B + C)] \cdot (A+C)$
$= [(A \cdot \bar B) + (A \cdot C) + (B \cdot \bar B) + (B \cdot C)] \cdot (A+C)$
$= [(A \cdot \bar B) + (A \cdot C) + 0 + (B \cdot C)] \cdot (A+C)$
$= A \cdot (\bar B + C) + B \cdot C$
From the above, we can observe that both LHS and RHS are the same. Hence the given Boolean identity is proved. The required proof is done.
To know more about Boolean visit:
https://brainly.com/question/27892600
#SPJ11
Boost manifold pressure is generally considered to be any manifold pressure above
a. 14.7 inches Hg.
b. 50 inches Hg.
c. 30 inches Hg.
Boost manifold pressure is generally considered to be any manifold pressure above 30 inches Hg. This is option C
What is Boost Manifold Pressure?A manifold is a type of equipment that operates by providing a pathway for air to enter an engine. It is designed to regulate and monitor the air that enters the engine for a vehicle to run optimally.
Boost manifold pressure is the amount of pressure required to drive a vehicle’s turbocharger, and it is an important metric to understand in the performance of the engine.A manifold pressure reading is essential to have if you want to achieve a specific performance in your vehicle, especially if you have a modified engine.
So, the correct answer is C
Learn more about pressurize at
https://brainly.com/question/1466472
#SPJ11
