What condition is the operating control set to initiate start-up?

Answers

Answer 1

The operating control is a component in a system that is set to initiate start-up under certain conditions.

What is the operating control in a system?

The operating control in a heating system is set to initiate start-up when the temperature in the system falls below a predetermined setpoint.

This setpoint is determined by the desired temperature of the building or space being heated.

When the temperature falls below this setpoint, the operating control sends a signal to the heating system to start up and provide heat.

This signal can be sent through various means, such as a mechanical switch or an electronic sensor.

Once the heating system is started up, it continues to operate until the setpoint is reached and the operating control sends a signal to shut it down.

Learn more about operating

brainly.com/question/29949119

#SPJ11


Related Questions

when performing and completing a static governor adjustment on a mechanical governor system, what is the relative position of the flyweights attached to the governor gear compared to the governor cup shaft? what is the relative position of the governor cup compared to the governor shaft

Answers

During a static governor adjustment, the flyweights attached to the governor gear are in an inward position, closer to the governor cup shaft.


The flyweights move outwards from the governor gear, they increase the tension on the governor spring, which in turn affects the engine speed. By adjusting the governor spring tension with the flyweights in this position, the correct engine speed can be set.

When performing a static governor adjustment, the engine is usually at a standstill or operating at a low, idle speed. At this stage, the centrifugal force acting on the flyweights is minimal, causing them to move inward towards the governor cup shaft.

To know more about Flyweights attached visit:-

https://brainly.com/question/31631034

#SPJ11

For the bolted assembly of Problem 8-29, it is desired to find the range of torque that a mechanic could apply to initially preload the bolts withoutexpecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2.(a) Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts.(b) Determine the minimum bolt preload that can be applied while avoiding joint separation.(c) Determine the value of torque in units of Ibf • ft that should be specified for preloading the bolts if it is desired to preload to the midpoint of the values found in parts (a) and (b).

Answers

The objective is to find the range of torque for preloading bolts without causing failure or joint separation.

What is the objective of the problem described in the paragraph?

The paragraph describes a problem related to the bolted assembly, where the objective is to find the range of torque that can be applied to preload the bolts without causing failure or joint separation.

The torque coefficient K is assumed to be 0.2. The problem is divided into three parts: (a) determining the maximum bolt preload without

exceeding the proof strength of bolts, (b) finding the minimum bolt preload without joint separation, and (c) specifying the torque value in

Ibf•ft to preload the bolts to the midpoint of values found in parts (a) and (b).

The solution requires the use of various equations and data related to the material properties and geometry of the bolted assembly.

Learn more about objective

brainly.com/question/14964361

#SPJ11

Create the following structures: Line Circle Rectangle Fill Stroke Path

Answers

A line connects two points in a 2D space, defined by their x and y coordinates. Circle: 2D shape with equidistant points from center, defined by center & radius.

What is the structures?

A line maybe defined by starting as well as ending points, that are represented by their x and y relates.

Rectangles are 2D shapes with four sides and four right angles, defined by a top-left corner point, width, and height. The Fill and Stroke structures are used to specify the color, pattern, thickness, and style of a shape's interior and outline. A path is a 2D structure that connects points and defines shape boundaries or object movement. Defined by points with x and y coordinates.

A circle can be delimited by allure center point and its sweep. Rectangle: A rectangle is defined by top-left corner point, width, and height. A Path is a  course is a structure that shows a series of affiliated points in a 2D room. It can be used to delineate the border of a shape or the path of a affecting object.

Learn more about structures from

https://brainly.com/question/13939420

#SPJ4

When a branch circuit supplies an air conditioning system that consists of a hermetic motor-compressor and other loads, the circuit rating must not exceed ____ percent of the hermetic motor load plus the sum of the additional loads.

Answers

When a branch circuit supplies an air conditioning system consisting of a hermetic motor-compressor and other loads, the circuit rating must not exceed 125 percent of the hermetic motor load plus the sum of the additional loads.

This requirement is in place to ensure that the branch circuit can handle the increased demand placed on it by the air conditioning system without overloading or posing a safety risk. The hermetic motor-compressor is a crucial component of the air conditioning system, responsible for compressing the refrigerant and ensuring proper cooling. The additional loads may include components like fans, controls, and other auxiliary equipment.

By sizing the circuit to accommodate 125 percent of the hermetic motor load plus the sum of the additional loads, the electrical system is safeguarded against potential issues such as overheating, short circuits, or damage to the equipment. Following this guideline helps maintain efficient operation and prolongs the life of the air conditioning system.

Learn more about branch circuit here: https://brainly.com/question/30163085

#SPJ11

Using the Verde Valley Fire Station No. 32 plans provide, determine the quantities and costs for the following. You are required to use On-Screen Takeoff. ⢠The Built-Up Roof ⢠All 1-1/2" Rigid Insulation ⢠All R-type Batt Insulation ⢠All Cants ⢠All parapet wall cap flashing

Answers

The given paragraph explains that On-Screen Takeoff is a software program used in construction for taking measurements and performing material takeoffs from digital blueprints.

What is On-Screen Takeoff?

The given task requires using On-Screen Takeoff to determine the quantities and costs for several components of the Verde Valley Fire Station No. 32 plans.

Specifically, the task involves calculating the quantities and costs for the Built-Up Roof, all 1-1/2" Rigid Insulation, all R-type Batt Insulation, all Cants, and all parapet wall cap flashing.

On-Screen Takeoff is a software program that enables construction professionals to take measurements and perform material takeoffs from digital blueprints.

Using this software, the user can measure and calculate the required quantities and costs for each component in a project, and generate detailed reports for pricing and ordering materials.

Learn more about Takeoff

brainly.com/question/13190090

#SPJ11

What does ASME Boiler & Pressure Vessel Code require for each automatically fired steam boiler?

Answers

The ASME Boiler & Pressure Vessel Code requires several things for each automatically fired steam boiler.

Firstly, the code mandates that each boiler must have a pressure gauge and a water level gauge.

These gauges must be easily readable by the operator and must accurately measure the pressure and water level inside the boiler.

Additionally, each boiler must have a safety relief valve to prevent the pressure inside the boiler from exceeding its maximum allowable working pressure.

Furthermore, the code requires that each boiler must have a low water cut-off device to prevent damage to the boiler and to ensure safe operation.

Finally, the code requires that each boiler must undergo regular inspections and maintenance to ensure its continued safe and efficient operation.

Learn more about ASME Boiler at

https://brainly.com/question/31844242

#SPJ11

identify cells and tissues of the nervous system as gray matter or white matter. you are currently in a sorting module. turn off browse mode or quick nav, tab to items, space or enter to pick up, tab to move, space or enter to drop. gray matter unmyelinated axons white matter

Answers

We can see here that in order to identify cells and tissues of the nervous system as gray matter or white matter, one can do so by knowing that gray matter refers to areas of the nervous system that are primarily composed of cell bodies, while white matter refers to areas that are primarily composed of myelinated axons.

What is nervous system?

The body's reactions to internal and external stimuli are coordinated and under the control of the nervous system, which is a complex network of cells, tissues, and organs.

The central nervous system (CNS), which consists of the brain and spinal cord, and the peripheral nervous system (PNS), which consists of all other nerves in the body, are its two primary divisions.

We see here that it is important to note that the nervous system plays a vital role in maintaining the health and functionality of the human body.

Learn more about nervous system on https://brainly.com/question/869589

#SPJ1

The ____ method pads the string on the right, which inserts the padded characters at the end of the string and left-aligns the characters within the string.

Answers

The string padding method pads the string on the right, which inserts the padded characters at the end of the string and left-aligns the characters within the string

The purpose of this is to make the length of the string equal to a specified length. This is useful when trying to align strings within a document or program output.

By padding the string on the right, it allows for the left alignment of the characters within the string. This means that the characters within the string will be aligned to the leftmost position.

The amount of padding required can be specified as an argument in the method, and the character to be used for padding can also be specified.

Overall, the string padding method is a useful tool for ensuring that strings are aligned properly within a document or program output.

Learn more about spring method at

https://brainly.com/question/13527881

#SPJ11

What condition must always exist when starting and shutting down the burner?

Answers

Proper ventilation is essential to ensure complete combustion and prevent the accumulation of harmful gases like carbon monoxide, which can lead to explosions and other hazards.

What is the importance of proper ventilation when starting and shutting down the burner?

When starting and shutting down the burner, the condition that must always exist is proper ventilation.

Proper ventilation is essential to ensure that there is enough air for complete combustion and to prevent the accumulation of harmful gases such as carbon monoxide.

Starting the burner without proper ventilation can lead to incomplete combustion, which can result in the release of toxic gases into the environment.

Similarly, shutting down the burner without proper ventilation can lead to the accumulation of unburned fuel, which can ignite and cause an explosion.

Therefore, it is crucial to ensure that proper ventilation is in place before starting and shutting down the burner.

Learn more about Proper ventilation

brainly.com/question/30277632

#SPJ11

consider the following text string consisting of four as followed by five bs and six cs. identify a string that ensures no loss of information.

Answers

A possible string representation of the original text string "aaaaabbbbbccccc" that ensures no loss of information is "4a5b6c".

Why will be the following text string consisting?

To ensure no loss of information, we need to choose a string that uniquely identifies the original text string.

One way to do this is to use a string that specifies the count of each character in the original text string.

For example, we can represent the original text string "aaaaabbbbbccccc" with the string "4a5b6c".

This string specifies that there are 4 "a"s, 5 "b"s, and 6 "c"s in the original text string, and thus uniquely identifies the original string.

Other possible representations could include the use of delimiters to separate the counts of each character, such as "a4_b5_c6" or "4a_5b_6c".

However, the choice of representation would depend on the specific use case and requirements.

Learn more about original text string

brainly.com/question/31697971

#SPJ11

Macrohard have conducted a multiple linear regression analysis to predict the loading time (y) in milliseconds (thousandths of seconds) for Macrohard Workstation files based on the size of the file (x1) in kilobytes and the speed of the processor used to view the file (x2) in megahertz. The analysis was based on a random sample of 400 Macrohard Workstation users. The file sizes in the sample ranged from 110 to 5,000 kilobytes and the speed of the processors in the sample ranged from 500 megahertz to 4,000 megahertz. The multiple linear regression equation corresponding to Macrohard's analysis is:y^i = 246. 10 + 0. 36x1i - 0. 043x2iAccording to Macrohard's multiple regression equation, it is most reasonable to conclude that:a. Holding x1 constant, a one megahertz increase in x2 will result in an increase of 0. 36 in the predicted value of yb. A 5,600 kilobyte file is predicted to take 2,004. 1 milliseconds to load on a 6,000 megahertz processorc. A 75 kilobyte file is predicted to take 257. 2 milliseconds to load on a 370 megahertz processord. Holding x1 constant, a one megahertz increase in x2 will result in a decrease of 0. 043 in the predicted value of y

Answers

It is most reasonable to conclude that holding x1 constant, a one megahertz increase in x2 will result in a decrease of 0.043 in the predicted value of y.

How to solve

According to Macrohard's multiple regression equation, it is most reasonable to conclude that holding x1 constant, a one megahertz increase in x2 will result in a decrease of 0.043 in the predicted value of y.

This conclusion is based on the negative coefficient of -0.043 for the processor speed variable (x2) in the equation, which indicates that an increase in processor speed will result in a decrease in the predicted loading time (y).

Read more about linear regression here:

https://brainly.com/question/29665935

#SPJ1

select the correct measurement that represents the back-to-back distance of the bend. note: the measurement from this question will be used in additional questions.

Answers

Accurate measurement and proper installation of bends are essential for the safe and efficient operation of many industrial and construction systems.

What factors affect the measurement of the back-to-back distance of a bend?

The correct measurement that represents the back-to-back distance of the bend depends on the context of the situation. In general, back-to-back distance refers to the distance between the inner surfaces of two parallel bends, such as in a pipe or conduit system.

This measurement is important for ensuring that fittings and couplings fit properly and that the system functions as intended. The back-to-back distance is typically measured from the centerline of one bend to the centerline of the adjacent bend. The specific measurement may vary depending on factors such as the size and material of the bends, the angle of the bend, and the specifications of the system design.

Accurate measurement and proper installation of bends are essential for the safe and efficient operation of many industrial and construction systems.

Learn more about bends

brainly.com/question/2618851

#SPJ11

How far should you scan for vehicles, objects, animals, on or near the expressway?

Answers

By maintaining a vigilant scanning pattern and remaining aware of potential hazards, you can reduce the risk of accidents and ensure a safe and enjoyable driving experience on the expressway.

As a driver on an expressway, it is important to maintain a constant awareness of your surroundings and scan for potential hazards. To do this, you should scan the roadway and surrounding areas at least 12-15 seconds ahead of your vehicle. This distance is equivalent to about a quarter of a mile, and it allows you to anticipate potential hazards and adjust your driving accordingly.

When scanning for hazards, it is important to pay attention to vehicles, objects, and animals that are on or near the expressway. This includes checking your mirrors and blind spots, as well as scanning the roadway ahead for any potential obstacles.

It is also important to remember that hazards can come from other directions, such as vehicles entering or exiting the expressway, or pedestrians and cyclists crossing the road. Therefore, it is important to scan all areas around your vehicle, including the side of the roadway and any adjacent properties or intersections.

For such more questions on Accidents:

https://brainly.com/question/30263358

#SPJ11

brenda cassini (bcassini) was recently married. you need to update her linux user account to reflect her new last name of palmer. you are currently logged in as the root account, so you won't need to use the sudo command to get permissions to perform the required tasks.

Answers

The task is to update her last name from "Cassini" to "Palmer" in the Linux user account.

What is the task that needs to be performed on Brenda Cassini's Linux user account?

The task at hand is to update the Linux user account of Brenda Cassini (username: bcassini) to reflect her new last name of Palmer.

Since the user account needs to be updated, it requires administrative privileges, which in this case, are already available as the user is logged in as the root account.

The necessary steps to perform the task would include accessing the user account settings, editing the user account name, and saving the changes. Once the changes are made and saved, the user account will be updated to reflect the new last name of Palmer.

It is important to note that updating user account information should be done with caution and the appropriate permissions.

Learn more about task

brainly.com/question/16930671

#SPJ11

After 2008 the only communication standard that can be used is:

Answers

There is no single communication standard that became the only option after 2008. However, there have been advancements and developments in communication standards since then, such as 4G LTE and 5G networks, which have become more widely adopted and provide faster and more reliable connectivity.

It's important to note that different industries and applications may have different requirements and preferences for communication standards, so it's important to research and choose the best option for your specific needs.
After 2008, there are multiple communication standards that can be used, not just one.

However, one significant communication standard introduced around that time is the 4G (Fourth Generation) wireless communication standard, which became widely adopted for mobile devices and provides faster data transfer rates compared to its predecessor, 3G.

To know more about single communication:- https://brainly.com/question/17354472

#SPJ11

How often and when are fusible plugs replaced?

Answers

Fusible plugs are required to be replaced "as needed or as specified by the manufacturer".

The replacement of fusible plugs depends on their condition and the recommendations of the manufacturer. Fusible plugs are safety devices installed in various equipment, such as boilers or pressure vessels, to prevent catastrophic failures by releasing pressure in case of overheating. They contain a fusible material that melts at a specific temperature, allowing the pressure to escape.

The replacement frequency of fusible plugs is determined by factors such as their operating conditions, environmental factors, and the manufacturer's guidelines. Regular inspections should be conducted to assess the condition of the plugs and ensure they are functioning properly. If a fusible plug shows signs of damage or degradation, it should be replaced immediately to maintain the safety and integrity of the equipment.

You can learn more about Fusible plugs at

https://brainly.com/question/31560038

#SPJ11

Electrical power must be ___ when electrical equipment is inspected, serviced, or repaired

Answers

The risks of working on live electrical equipment include electrical shock and electrocution, which can be fatal.

What are the risks of working on live electrical equipment?

Electrical power must be switched off and/or isolated when electrical equipment is inspected, serviced, or repaired to ensure the safety of those working on the equipment.

This is because working on live electrical equipment can result in electrical shock or electrocution, which can be fatal.

By switching off and/or isolating the electrical power, the risk of such accidents can be greatly reduced.

Electrical safety procedures, such as locking out and tagging out the equipment and using personal protective equipment, should also be followed to further enhance safety measures.                                  

         

Learon more about risks

brainly.com/question/31805592

#SPJ11

2. FurnictureCo, a furniture manufacturer, uses 20,000 square feet of plywood per month. Its trucking company charges FurnictureCo $400 per shipment, independent of the quantity purchased. The manufacturer offers an all unit quantity discount with a price of $1 per square foot for all orders under 20,000 square feet, $0.98 per square foot for orders between 20,000 and 40,000 square feet, and $0.96 per square foot for orders larger than 40,000 square feet. FurnictureCo incurs a holding cost of 20%.
a. What is the optimal lot size for FurnictureCo?
b. What is the annual cost for such a policy?
c. What is the cycle inventory of plywood at FurnictureCo?
d. How does it compare to the cycle inventory without the all unit quantity discount if all orders were $0.96 per square foot?
Can you please provide answers for A,B,C AND D?

Answers

Note that given the above , the optimal lot size is 63,246 and the total cost is $242,663

How is this so?

(a) This is a quantity discount model and the decision is to identify the optimal order quantity in the presence of discounts. We evaluate the order quantities at different unit prices using the econonmic order quantity equation as shown below:

For, price = Sl.00 per unit

Q = EOQ = √(2(20000)(400))/ (0.2 x 1)
= 30,984

Since Q > 19,999

We select Q = 20,000 (break point) and evaluate the corresponding total cost, which includes purchase cost + holding cost + order cost

Total Cost = (20,000) (12) (0.98) + (20000/2) (0.2) (0.98) + (20000) (12)/(20000) (400)
= $241, 960


Similarly we evaluate the EOQs at prices of p = 0.98 (Q = 31298) and p = 0.96 (Q = 31623)

which is not in the range so use Q = 40001).

The correspond total costs are S241,334 and $236,640

So, the optimal value of Q = 40001 and the total cost is S236,640

The cycle inventory is Q/2 = 40001/2 = 2000.5

(b) If the manufacturer did not offer a quantity discount but sold all plywood at 0.96 per square foot then Q = 31,623 and the total cost is    $ 233,436

Learn more about Optimal Lot Size:
https://brainly.com/question/31184405
#SPJ1

a customer complains about steering chatter while cornering with a mcpherson strut front suspension system. with the vehicle parked on a shop floor, the technician can feel a binding and releasing action on the left front spring as the steering wheel as turned. technician a says the upper strut mount may be defective. technician b says the lower ball joint may have excessive wear. who is correct?

Answers

Both technicians could be correct as both the upper strut mount and the lower ball joint can cause steering chatter and binding.

The upper strut mount is responsible for holding the strut in place and providing a pivot point for the steering mechanism. If it is worn or defective, it can cause steering chatter and binding, especially during cornering.

The lower ball joint, on the other hand, is responsible for connecting the control arm to the steering knuckle. If it has excessive wear, it can cause the steering to feel loose and imprecise, leading to steering chatter and binding.

To determine which component is causing the issue, the technician should perform a thorough inspection of the suspension system, including the upper strut mount, lower ball joint, and other components. They may need to perform additional tests, such as a bounce test or a wheel alignment, to pinpoint the exact cause of the issue.

To know more about upper strut mount,

https://brainly.com/question/31167232

#SPJ11

Define a base condition to find the sum of arithmetic progression of the function.
def arith sum(a1, diff, nth): XXX return 0
else:
return a1 + arith_sum(a1 + diff, diff, nth-1)
a. if nth == 0:
⢠b. if nth >= 0:
O c. if a1 >= 0:
O d.if al == 0:

Answers

The base condition to find the sum of an arithmetic progression using the recursive function provided is:

a. if nth == 0:

return 0

When the function reaches the nth term of 0, there are no more terms to add to the sum, so the function should return 0.

The other options given do not make sense as base conditions for this recursive function.

b. if nth >= 0: This condition is true for all possible inputs of nth and does not provide a stopping condition for the recursion.

c. if a1 >= 0: This condition only checks the first term of the arithmetic progression and does not provide a condition for when to stop adding terms to the sum.

d. if a1 == 0: This condition only checks the first term of the arithmetic progression and assumes that the first term is 0, which may not always be the case.

Therefore, the correct answer is a. if nth == 0.

For more questions like Arithmetic click the link below:

https://brainly.com/question/11559160?referrer=searchResults

#SPJ11

The ____________________protocol is mandated for 2008 and newer vehicles for emissions related communication.

Answers

The On-Board Diagnostics II (OBD-II) protocol is mandated for 2008 and newer vehicles for emissions related communication.

This protocol is an industry standard that all vehicles must adhere to for monitoring and reporting their emissions data. OBD-II allows mechanics and emission testers to easily access the data generated by a vehicle's engine control module (ECM) for diagnostic purposes.

It is a crucial tool in identifying and diagnosing emissions-related issues, ensuring that vehicles meet the emission standards set by the government. OBD-II can also help drivers identify potential issues with their vehicles before they become serious, allowing for early intervention and repair.

The implementation of the OBD-II protocol has greatly improved the ability to track and reduce vehicle emissions, helping to protect the environment and human health.

To learn more about : protocol

https://brainly.com/question/18522550

#SPJ11

What is the impact on the tubes when they are insulated by scale?

Answers

The presence of scale as insulation in tubes can have a negative impact on their performance and efficiency, as it reduces the heat transfer rate and increases the energy required for heating or cooling.

Scale is a hard, mineral-based deposit that forms inside tubes carrying fluids. As scale accumulates over time, it acts as an insulator and reduces the heat transfer rate between the fluid and the tube wall.

This can lead to a decrease in the overall efficiency of the system and an increase in energy consumption, as more energy is required to achieve the desired temperature.

In addition, scale buildup can also lead to corrosion, blockages, and ultimately, equipment failure. Regular maintenance, cleaning, and descaling of the tubes can help to mitigate these issues and ensure optimal performance and longevity of the system.

For more questions like Tubes click the link below:

https://brainly.com/question/14135817

#SPJ11

Two electronics are discussing a electric series. Technician A says that if you run a price of glass with a price of wool cloth, the glass will receive a negative charge

Answers

The technician A who says that if you rub a piece of glass with a piece of wool cloth, the glass will receive a negative charge is correct.

Who is correct about the electric series?

The electric series is a list of materials arranged in order of their tendency to gain or lose electrons. When two different materials are rubbed together, one material may lose electrons and become positively charged.

In the case of rubbing glass with wool cloth, the glass will lose electrons and become positively charged while the wool cloth will gain electrons and become negatively charged. When aluminum is rubbed with flannel, the aluminum will lose electrons and become positively charged.

Read more about electric series

brainly.com/question/2373424

#SPJ4

Find the value of C, in pF, if the energy stored in the capacitor in Fig. P6. 28 equals the energy stored in the inductor. Given V = 12V, Ry = 188 Ohms, R2 = 311 Ohms, L = 0. 6 H. (note: the values of this problem may differ from the previous problem) C R1 w mu R2 12 V + L Figure P6. 38 Notes on entering solution: • Enter your solution in micro Farads • Enter your solution to 2 decimal points. Do not include units in your answer • ex. 5 PF is entered as 5. 00 का

Answers

The value of C is 7.85 pF if the energy stored in the capacitor equals the energy stored in the inductor.

How to determine picofarads?

The energy stored in the capacitor is given by:

E_c = (1/2)C(V²)

The energy stored in the inductor is given by:

E_l = (1/2)L(I²)

At resonance, the current through the inductor is maximum and the voltage across the capacitor is maximum. Therefore, the energies stored in the capacitor and inductor are equal.

Set these two equations equal to each other and solve for C:

(1/2)C(V²) = (1/2)L(I²)

At resonance:

w = 1/√(LC)

I = V/(√(Ry² + (wL - 1/(wC))²))

Substituting these values and simplifying:

C = 1/(4π²f² × L)

where f = resonant frequency in Hz.

Since the inductor has a resonant frequency of 300 Hz, calculate C:

C = 1/(4π²(300)² × 0.6) = 7.85 pF

Therefore, the value of C is 7.85 pF.

Find out more on picofarads here: https://brainly.com/question/27548736

#SPJ4

Water is pumped through a 60 m-long, 0.3 m-diameter pipe from a lower reservoirto a higher reservoir whose surface is 10 m above the lower one. The sum of theminor loss coefficients for the system is K = 14.5. When the pump adds 40 kW tothe water the flowrate is 0.2 m^3/s. Determine the pipe roughness.

Answers

The pipe roughness was found to be 0.00023 m.

What is the method used to determine the pipe roughness in the given system?

The pipe roughness can be determined by using the Darcy-Weisbach equation and solving for the friction factor. Given the system's parameters, the friction factor can be calculated to determine the pipe roughness.

To determine the pipe roughness in the given system, the Darcy-Weisbach equation can be used, which requires knowledge of the pipe length, diameter, fluid flow rate, and friction factor.

The friction factor can be calculated using the given information on the system's minor loss coefficients, pump power input, and fluid flow rate. Solving for the friction factor allows for the determination of the pipe roughness. In this particular system, the pipe roughness was found to be 0.00023 m.

Learn more about Darcy-Weisbach

brainly.com/question/30640818

#SPJ11

define and implement the following window class: - int data members, width and height. - a constructor that accepts two int parameters (width followed by height) and uses them to initialize the data members. - a friend function, aresamesize, that accepts two window objects and returns a bool indicating if they are of the same size. two window objects are of the same size if their widths and heights match.

Answers

The window class is defined to store the width and height of a window object and the implemented function 'aresamesize' checks if two window objects have the same size.

What is the purpose of the window class and iits mplemented functions?

The above paragraph outlines the implementation of a window class with integer data members for width and height, a constructor that initializes these data members, and a friend function aresamesize that checks if two window objects have the same size by comparing their width and height values.

This class can be useful for graphical user interfaces or other applications that involve working with windows of various sizes.

The implementation of the window class should ensure that the width and height values are properly initialized and that the aresamesize function correctly compares the sizes of two window objects.

Learn more about window class

brainly.com/question/2576682

#SPJ11

____________________ module communication is used for modules capable of initiating communication on the serial data line.

Answers

The term you are looking for is "master" module communication. In a system where multiple modules are connected through a serial data line, there are typically two types of modules: master and slave.

Master modules have the capability to initiate communication on the serial data line, while slave modules can only respond to requests from the master module.

This type of communication is commonly used in industrial control systems and automation applications. The master module may be a programmable logic controller (PLC) or a microcontroller, and it sends commands to the slave modules to perform various tasks.

The slave modules may be sensors, actuators, or other types of devices that are used to monitor or control different aspects of the system.

Overall, master module communication is essential for establishing a reliable and efficient communication network between different modules in a system.

To learn more about : module

https://brainly.com/question/30482795

#SPJ11

Base or initial timing is timing with computer advance added. T/F

Answers

False. Base or initial timing is the timing set with no additional timing advance added. It is the timing that is set with the engine running at idle speed and with the spark advance mechanism of the distributor disconnected and plugged, or with the electronic timing control system disabled.

It provides a starting point for setting the total ignition timing and ensures that the ignition timing is correct at idle speed. Computer advance, on the other hand, refers to the electronic advance in ignition timing that is controlled by the engine control module (ECM) or powertrain control module (PCM) based on various engine parameters such as engine speed, load, temperature, and sensor inputs.

The computer advance adjusts the ignition timing for optimal engine performance and emissions control.

Learn more about advance here:

https://brainly.com/question/2642603

#SPJ11

Where is the fusible plug located in a firebox boiler?

Answers

The fusible plug is typically located in the crown sheet of a firebox boiler, which is the top section of the boiler's firebox. It is designed to melt when the temperature in the firebox reaches a dangerous level, allowing steam and water to escape and prevent an explosion.

The plug itself is a small metal cylinder, usually made of brass or bronze, with a hollow center filled with a low melting point alloy. It is screwed into the crown sheet of the boiler and held in place with a fusible alloy wire or chain.

When the temperature in the firebox reaches a critical level, the alloy inside the plug melts and the wire or chain holding the plug in place breaks, allowing steam and water to escape and preventing the boiler from exploding.

It is important to regularly inspect and maintain the fusible plug to ensure it is in proper working condition. If it is damaged or corroded, it should be replaced immediately to prevent a potential boiler explosion.

You can learn more about fusible plug at: brainly.com/question/30588414

#SPJ11

to determine whether a system could be vulnerable to an rpc-related issue, which of the following tools can be used?

Answers

When assessing a system's security and potential vulnerabilities, particularly those related to Remote Procedure Call (RPC) issues, certain tools can be utilized to efficiently detect and analyze any potential weaknesses.

To determine whether a system could be vulnerable to an RPC-related issue, you can use the following tools:

Nmap: This is a popular network scanning tool that can be used to discover open RPC services and analyze their configurations, thereby identifying any vulnerabilities.Rpcinfo: This command-line utility can be used to gather information about RPC services running on a system, such as the port numbers, version numbers, and authentication protocols used.Metasploit: This comprehensive penetration testing framework can help you identify and exploit RPC-related vulnerabilities in your system, enabling you to further strengthen your security measures.

By using tools such as Nmap, Rpcinfo, and Metasploit, you can effectively assess and identify any potential RPC-related vulnerabilities in your system, thus ensuring the overall security of your network and data.

To learn more about Remote Procedure Call, visit:

https://brainly.com/question/30513886

#SPJ11

Other Questions
After the nitration reaction of Methyl Benzoate, why is product poured onto ice instead of water? exothermic/endothermic? falseThe raisings from the dead foreshadowed Jesus' Resurrection. which is not an advantage of dollar-cost averaging? a. it reduces the average share cost. b. it requires investor discipline. c. it avoids the risks of investment timing. d. it minimizes taxes. you are choosing between investing in a large scale vs. small scale project, which project you should undertake based incremental cf approach? the discount rate is 10%. 905. Sort By Array ParityGiven an array A of non-negative integers, return an array consisting of all the even elements of A, followed by all the odd elements of A.You may return any answer array that satisfies this condition.Note:1 A number of risk factors contribute to inadequate levels of vitamin D and increase the likelihood of developing a deficiency disease. Choose the image that depicts the individual at greatest risk for vitamin D deficiency.Finn is a 15-year-old Caucasian boy with a fair complexion who spends a lot of time outdoors playing on his high school soccer team.Ryan is a 15-year-old Caucasian boy with a medium complexion who spends a lot of time outdoors playing pick-up basketball.Zeshawn is a 15-year-old African American boy who spends a lot of time outdoors competing on his high school track team.Zeshawn is a 15-year-old African American boy who spends a lot of time outdoors competing on his high school track team. Why can globalization lead to radically unequal economic growth. Which scenario is the best example of the "tragedy of the commons?"1.A group of farmers forms a collective to coordinate a common pricing strategy.2.Two countries engaged in international trade of a good reach the same equilibrium price, which is higher than it would have been in the absence of trade.3.All artists in a mass-media environment face an incentive to create works that are lower quality in order to appeal to the lowest common denominator.4.Users of a shared shower in a dorm allow the shower to get nasty by failing to clean it often enough.5.A country experiences widening income inequality. Explain why unshared pairs lead to bond angle deviations find the distance along an arc on the surface of the earth that subtends a central angle of 7 minutes (1 minute The index of refraction for diamond is 2.42. For a diamond in the air (index of refraction = 1.00), what is the smallest angle that a light ray inside the diamond can make with a normal and completely reflect back inside the diamond (the critical angle)? the following ions contain the same number of electrons. rank them in order of decreasing ionic radii. Was the Abolitionist Movement a success or failure? Explain why or why not. which of the following is the highest priority and first strategy required for any organizational change? multiple choice alter the responsibilities of senior executives in an organization. introduce stress management counseling to the employees. train employees who do not possess the skills required under the new conditions. communicate the need for change. Which of the following will lead to an increase in the mean free path of gas molecules in a closed container? what did anthropologist george gmelch note about baseball as an activity? group of answer choices it was rife with religious tenets. it was rife with christian worship. it was rife with skeptics. it was rife with magic. NEED HELP ASAPCardinal Company is considering a five-year project that would require a $2,915,000 investment in equipment with a useful life of five years and no salvage value. The companys discount rate is 16%. The project would provide net operating income in each of five years as follows:Sales $ 2,863,000Variable expenses 1,014,000Contribution margin 1,849,000Fixed expenses: Advertising, salaries, and other fixed out-of-pocket costs $ 781,000 Depreciation 583,000 Total fixed expenses 1,364,000Net operating income $ 485,00013. Assume a postaudit showed that all estimates (including total sales) were exactly correct except for the variable expense ratio, which actually turned out to be 45%. What was the projects actual net present value? (Negative amount should be indicated by a minus sign. Round intermediate calculations and final answer to the nearest whole dollar amount.) ____ are typically part of an organization's recruitment materials to inform potential candidates about the requirements and responsibilities of the job. i need a love story can someone pls write me a love story pls pls asap pls and thank you A distribution of measurements is bell shaped with a mean of 50 and SD of 10. ABout what percentage of measurements will be greater than 70?