what force is necessary to stretch a spring 48 cm, if the spring constant is 270 n/m?

The moments of inertia are ranked as follows, from smallest to largest: I1  < I2 (for both pairs of balls connected by the long rods) < I3 (for both pairs of balls connected by the middle rod).

To rank the moments of inertia of the three pairs of balls, we need to consider the distribution of mass around the axes passing through the centers of the rods.

For I1, we can consider the pair of balls at the ends of the rod to be point masses, with all of their mass located at their centers. The moment of inertia of this pair of balls about the axis through the center of the rod can be calculated as [tex]I1 = 2mr^2[/tex], where m is the mass of each ball and r is the distance from the axis to the center of each ball.

Since the masses are equal and the distance from the axis to the center of each ball is the same, I1 is the same for both pairs of balls connected by the rod.

For I2, we need to consider the distribution of mass along the rod. Since the rod is very light, we can assume that all of the mass is located at the center of the rod. The moment of inertia of the rod about the axis passing through its center is [tex]I2 = (1/12)ML^2[/tex], where M is the mass of the rod and L is its length.

Since the masses and lengths of the two rods are the same, I2 is the same for both pairs of balls connected by the rods.

For I3, we need to consider the distribution of mass around the axis passing through the center of the rod that connects the two pairs of balls.

Since the masses of the balls are not located at a fixed distance from this axis, we need to use the parallel axis theorem to calculate I3.

The parallel axis theorem states that the moment of inertia of an object about any axis parallel to its center of mass axis is given by[tex]I3 = Icm + Md^2,[/tex] where Icm is the moment of inertia of the object about its center of mass axis, M is the mass of the object, and d is the distance between the two axes.

For each pair of balls, the moment of inertia about the axis passing through its center of mass axis can be calculated as[tex]Icm = 2mr^{2}/5,}[/tex]where r is the distance between the two balls.

The distance between the two axes is the length of the rod connecting the two pairs of balls, which is the same for both pairs. Therefore, I3 is the same for both pairs of balls connected by the rod.

For more question on moments of inertia visit:

https://brainly.com/question/14460640

#SPJ11

The pattern obtained in the Young's double-slit experiment cannot be replicated by placing two lasers side by side. The interference pattern is a result of the wave nature of light, and coherent light beams from lasers do not exhibit this phenomenon.

The Young's double slit experiment is a classic demonstration of the wave-like nature of light. When a single light beam is passed through two closely spaced parallel slits, it creates an interference pattern on a screen placed behind the slits. This pattern results from the interference of the two waves that are diffracted through the slits.
Now, coming to the question of whether the same pattern would be obtained if two lasers of the same wavelength were side by side, the answer is no. This is because the light emitted by lasers is coherent and does not undergo diffraction. When two lasers of the same wavelength are placed side by side, the light beams do not interfere with each other, and no interference pattern is observed on the screen placed behind them.
In the double-slit experiment, the wave nature of light is essential for the pattern formation. When two waves are diffracted through the slits, they interfere constructively and destructively, leading to the formation of a series of bright and dark fringes. The distance between the two slits is also crucial for the pattern formation. If the slit separation is changed, the pattern on the screen changes as well.

To know more about Young's experiment visit :

https://brainly.com/question/29885741

#SPJ11

The people outside of a plane do not hear the same sound volume as those inside the plane. the nuclear volume of the sound outside the plane is likely to be much lower and may not cause the same level of discomfort or hearing damage.

The sound waves are inside an enclosed space like a plane cabin, they bounce off the walls and ceiling, which can amplify the volume of the sound. On the other hand, when sound waves are outside, they can disperse in all directions, and the distance between the source of the sound and the listener can affect how loud the sound is perceived. Another factor that affects the nuclear volume of sound inside and outside a plane is the type of sound. For example, the sound of the engines is likely to be much louder outside the plane, while other sounds like conversations may be louder inside the cabin. In general, the sound volume inside a plane can be quite high, especially during takeoff and landing, and it is important for passengers to protect their hearing by using earplugs or noise-cancelling headphones. However, the volume of the sound outside the plane is likely to be much lower and may not cause the same level of discomfort or hearing damage.

learn more about nuclear here.

https://brainly.com/question/13090058

#SPJ11

The law of reflection states that when light strikes a flat surface and is reflected, you can draw a line perpendicular to the surface so that the angle of incidence (light moving toward the surface) and the angle of reflection (light reflected away from the surface) will be equal.

If the angle of incidence O1, is 22 degrees, what is the angle of reflection is also 22 degree.

When two distinct media come together at an interface, a wavefront might reverse direction so that it returns to the first medium, which is known as reflection. The reflection of light, sound, and water waves are typical examples. According to the law of reflection, the angle at which the wave impinge on the surface matches the angle at which it is reflected for specular reflection (such as at a mirror).

To know more about Reflection :

https://brainly.com/question/30270479

#SPJ1.

There are two types of electromagnetic waves that are commonly used by the police force: radio waves and infrared waves. the police force are radio waves and infrared waves. Radio waves are used for communication, while infrared waves are used for night vision.

The Radio electromagnetic waves are used by police forces for communication purposes. They are a type of EM wave that is used to transmit signals over long distances. Police radios use radio waves to communicate with other officers or with their headquarters. The radio waves are sent out from a transmitter and then picked up by a receiver. The radio waves used by police radios are usually in the frequency range of 150 MHz to 800 MHz's Infrared waves are used by police forces for night vision. Infrared waves are a type of EM wave that is invisible to the human eye but can be detected by special equipment. This technology is particularly useful in search and rescue operations, as well as in surveillance and tactical operations. In conclusion, the two types of EM waves commonly used by the police force are radio waves and infrared waves. Radio waves are used for communication, while infrared waves are used for night vision.

learn more about electromagnetic here.

https://brainly.com/question/30415081

#SPJ11

During the winter months in the middle latitudes, the jet stream shifts toward the equator. This shift is caused by the tilt of the Earth's axis and the resulting change in the angle of the sun's rays. The jet stream is a narrow band of strong winds that blow from west to east in the upper atmosphere.

It can have a significant impact on weather patterns, bringing cold air from the north and warm air from the south. The jet stream is also a key factor in the formation of storms and hurricanes. Overall, understanding the behavior of the jet stream is crucial for predicting and preparing for weather events. During the winter months in the middle latitudes, the jet stream shifts toward the equator. This shift occurs due to differences in temperature between the cold polar air and the warmer air at lower latitudes. The jet stream is a strong, narrow air current found in the upper atmosphere, and it has a significant impact on weather patterns.

The shift of the jet stream towards the equator during winter months affects weather conditions in several ways. First, it can lead to the development of low-pressure systems that bring cold, snowy, or rainy weather to regions in the middle latitudes. Second, the shifted jet stream can cause more extreme temperature fluctuations as cold polar air is brought further south, leading to more frequent and intense cold snaps.

To know more about latitudes visit :-

https://brainly.com/question/24260105

#SPJ11

The cooling of a parcel of air as it is lifted up over a mountain is primarily caused by adiabatic expansion.

As air rises, it experiences a decrease in atmospheric pressure due to the decrease in the weight of the overlying air. This decrease in pressure leads to adiabatic expansion, where the parcel of air expands and does work against its surroundings without gaining or losing heat.

According to the ideal gas law, as the volume of the parcel of air increases during expansion, its temperature decreases. This is known as adiabatic cooling. The cooling occurs because the expanding air does work by pushing against the surrounding air molecules, causing them to move faster and thus reducing the average kinetic energy (temperature) of the parcel.

The adiabatic cooling process is responsible for the formation of clouds, precipitation, and other weather phenomena associated with the lifting of air masses over mountains or through other atmospheric processes such as convection.

To know more about adiabatic expansion, refer here:
https://brainly.com/question/4597803#
#SPJ11

While using a pulley system may make lifting objects feel easier, it doesn't actually reduce the total amount of work done. Instead, it redistributes the work over a larger distance, allowing you to apply less force to achieve the same result.

When using a single pulley, the mechanical advantage is one, meaning that the force required to lift the object remains the same. However, the pulley changes the direction of the force, making it more convenient to lift the object. In a more complex pulley system, the mechanical advantage can be greater than one, reducing the force needed to lift the object. But keep in mind that the total work done, which is the product of force and distance, remains constant.

To summarize, using a pulley doesn't decrease the work done, but rather redistributes the effort over a larger distance and makes lifting objects feel easier. Be sure to explain this concept to your friend so they can better understand the advantages and limitations of pulley systems.

To know more about distance click this link-

brainly.com/question/31713805

#SPJ11

If a baseball is hit almost straight up into the air with a speed of about 20 m/s a) The baseball reaches a maximum height of approximately 20.41 meters. b) The baseball remains in the air for approximately 2 seconds.

a) To determine the maximum height, we can use the equation for vertical displacement in projectile motion.

The initial vertical velocity is 20 m/s, and the final vertical velocity at the highest point is 0 m/s.

Using the equation v² = u² + 2as, where v is the final velocity, u is the initial velocity, a is the acceleration, and s is the displacement, we can solve for the displacement.

Rearranging the equation, we have s = (v² - u²) / (2a).

Since the acceleration due to gravity is -9.8 m/s² (taking downward as negative), the displacement is s = (0² - 20²) / (2*(-9.8)) = 20.41 meters.

b) The time of flight can be determined using the equation s = ut + (1/2)at², where s is the displacement, u is the initial velocity, a is the acceleration, and t is the time.

In this case, the displacement is 0 meters (as the baseball returns to the ground).

Rearranging the equation, we have t = √(2s / a).

Plugging in the values, we get t = √(2*20.41 / 9.8) ≈ 2 seconds.

To know more about gravity, refer here:
https://brainly.com/question/29762388#
#SPJ11

There could be several reasons why a 3-cylinder diesel engine is leaking oil from the hose going to the oil cover at the top of the engine:

Worn or damaged gaskets

Overfilling of oil

Blocked or clogged ventilation system

Faulty oil pump

Worn or damaged gaskets: The gaskets between the oil cover and the engine block may have worn out or become damaged, causing oil to leak out.

Loose or damaged fittings: The hose or fittings that connect the oil cover to the engine block may be loose or damaged, causing oil to leak out.

Overfilling of oil: Overfilling the engine with oil can cause excess pressure and force oil out of the cover.

Blocked or clogged ventilation system: The ventilation system in the engine may be blocked or clogged, causing pressure to build up and oil to leak out.

Faulty oil pump: A faulty oil pump can cause excessive oil pressure, leading to oil leaks.

It is best to have a professional mechanic inspect the engine to diagnose the exact cause of the oil leak and perform the necessary repairs.

Learn more about cylinder diesel  here:

https://brainly.com/question/8829745

#SPJ11

The sum of the formal charges of the atoms in a molecule or polyatomic ion must equal the overall charge of the species. Formal charge is a way of keeping track of the distribution of electrons in a molecule or ion.

It is calculated by subtracting the number of electrons assigned to an atom in a molecule from the number of valence electrons of that atom in the neutral state. For a neutral molecule, the sum of the formal charges of all the atoms should be zero. For a polyatomic ion with a positive or negative charge, the sum of the formal charges of all the atoms should be equal to the overall charge of the ion. This is a useful tool for determining the most likely arrangement of atoms in a molecule or ion, and for predicting the polarity of a molecule.

To know more about polyatomic ion click here:

brainly.com/question/792714

#SPJ11

It is TRUE And Most large storage systems, such as those used in servers, data centers, and enterprise-level storage solutions, are based on magnetic hard disks. These disks use spinning platters coated with a magnetic material to store data. This technology has been around for several decades and has been refined over time to provide high storage capacities, reliable performance, and cost-effectiveness.
 

With the rise of solid-state drives (SSDs), which use flash memory to store data, some storage systems have started to incorporate a combination of magnetic and solid-state drives. This is because SSDs offer several advantages over traditional hard disks, including faster read and write speeds, lower power consumption, and higher durability.

While most large storage systems are still based on magnetic hard disks, the use of a combination of magnetic and solid-state drives is becoming more common as SSD technology continues to improve.

To  know more about storage visit :-

https://brainly.com/question/86807

#SPJ11

The magnitude of the motional emf induced in the rod can be calculated using the equation e = Blv, where B is the magnetic field strength, l is the length of the rod, and v is the velocity of the rod.

Assuming that the magnetic field strength is 0.2 T, the length of the rod is 0.5 m, and the velocity of the rod is 3 m/s, we can calculate the magnitude of the motional emf as follows:

e = Blv
e = (0.2 T) * (0.5 m) * (3 m/s)
e = 0.3 V

Therefore, the magnitude of the motional emf induced in the rod is 0.3 volts, expressed to at least three significant figures.

To know more about magnitude please visit..

brainly.com/question/31260554

#SPJ11

The Doppler technique, also known as the radial velocity method, measures the wobbling motion of a star caused by the gravitational pull of its orbiting planet. This motion is directly related to the mass of the planet, allowing astronomers to estimate its minimum mass. However, the technique cannot determine the orientation of the planet's orbit, which means that the true mass of the planet could be higher if the orbit is inclined towards our line of sight. Additionally, the Doppler technique is more sensitive to massive planets orbiting close to their stars, as their gravitational pull causes a stronger wobble. This means that smaller planets or those farther from their stars may not be detectable with this method. Therefore, the Doppler technique provides a measure of the minimum mass of a planet, but its true mass could be higher and its detection is limited by factors such as orbital orientation and distance from the star.

Using these tools, the student can calculate the total kinetic energy before and after the collision and compare the values. If the total kinetic energy is conserved within the acceptable range of experimental uncertainty, the collision can be considered elastic.

A student can use a combination of the following measuring tools to verify that the collision is elastic:
1. Motion sensors: These can track the velocities of the two objects before and after the collision, allowing the student to determine whether the total kinetic energy is conserved.
2. Scales or force sensors: These can measure the masses of the objects, which are necessary to calculate their kinetic energies.

to know more about collisions visit:

https://brainly.com/question/30338112

#SPJ11

When we charge up the Faraday cup, we are essentially creating a surface with a net charge. The charge collected at various points on and in the cup will depend on the distribution of the charge on the surface of the cup.

A Faraday cup is an instrument that is used to measure the charge of a beam of particles or ions. When the beam is directed into the cup, the charge is collected on the inner surface of the cup. The cup is then disconnected from the beam and the charge collected can be measured using a sensitive electrometer.
When we charge up the Faraday cup, we are essentially creating a surface with a net charge. The charge collected at various points on and in the cup will depend on the distribution of the charge on the surface of the cup. The charge distribution on the surface of the cup can be affected by a number of factors including the shape of the cup, the size of the beam, and the material of the cup.
Typically, the charge collected at different points on and in the cup will be proportional to the amount of charge collected by the cup as a whole. However, there may be variations in the charge distribution that can affect the measurements.
By measuring the charge at various points on and in the cup, we can gain insights into the properties of the beam and the cup itself. For example, we can use the measurements to determine the charge density of the beam, which can be important for understanding the behavior of the beam in various environments. We can also use the measurements to evaluate the performance of the cup, such as its ability to collect charge efficiently and its sensitivity to noise.

To know more about charge visit :

https://brainly.com/question/30163160

#SPJ11

Answer:

B) False

Explanation:

It is false because stars that form in nebule disrupt the cloud of gas, which prevents further star formation. When that star dies, it releases less matter than the original dust cloud had, eventually resulting in the cloud not having enough matter to make another star after several generations. And even if we were to say that the gas is continually recycled (which it is not), eventually the expansion of space will cause the universe to drift apart, and stars would not be able to form from dust clouds anymore.

This means that it takes approximately 6.93 seconds for the envelope amplitude of the signal to fall to 50% of its initial value. It's important to note that the actual time it takes for the envelope amplitude to decay will depend on the specific characteristics of the signal and the circuit or system that generates it.

The time it takes for the envelope amplitude to fall to 50% of its initial value is referred to as the half-life of the signal. The half-life can be calculated using the decay constant, which is a measure of how quickly the signal decays. The formula for the half-life of a signal is given by:
T1/2 = ln(2)/λ

The decay rate can be determined by examining the circuit or system that generates the signal.
τ = RC
Where R is the resistance of the circuit and C is the capacitance. The decay constant can then be calculated as:

λ = 1/τ
Once we know the decay constant, we can use the formula for the half-life to calculate how much time elapses before the envelope amplitude falls to 50% of its initial value.
T1/2 = ln(2)/0.1 = 6.93 seconds

To  know more about amplitude visit :-

https://brainly.com/question/8480265

#SPJ11

B. Defense in depth keeps senior management out of the activities of the security department is not an advantage of a defense-in-depth security design. The other options are correct. Defense in depth is a layered approach to security that uses multiple and overlapping security controls to provide protection against various threats and attacks.

By avoiding single points of failure, defense in depth ensures that if one security control fails, other controls can still provide protection. By dividing and conquering, defense in depth can separate complex projects into smaller and more manageable pieces. By filtering user interactions, defense in depth can reduce the risk of unauthorized access and limit the potential damage from security breaches. However, defense in depth should not keep senior management out of the activities of the security department, as their support and involvement are crucial for the success of the security program.

To know more about  senior management  click this link -

brainly.com/question/29997891

#SPJ11

Beta Centauri has a larger radius compared to Alpha Centauri B. This information allows us to determine their relative sizes despite not having specific measurements. The correct option is B.

While we know the colors and spectral types of the two stars, we do not have information on their sizes or radii. The color and spectral type of a star give us information on its temperature, luminosity, and chemical composition, but not necessarily its size. Therefore, we cannot determine the relative sizes of alpha centauri b and beta centauri based on this information alone.

Beta Centauri is a blue main sequence star, which means it is hotter and more massive than Alpha Centauri B, an orange main sequence star. In general, blue stars are larger in size compared to orange stars.

To know more about radius visit :-

https://brainly.com/question/29849775

#SPJ11

The statement "a 3,000 pound car traveling at 70 mph has 15.8 million pounds of force to release in a crash." is false

The force that a car has during a crash depends on the deceleration that occurs, which is determined by factors such as the distance over which the car decelerates and the duration of the impact.

The statement given in the question is incorrect and misleading. It is important to note that a 3,000 pound car traveling at 70 mph has a high amount of kinetic energy, and crashes can have significant and dangerous consequences even without millions of pounds of force being involved.

To know more about force  , refer here :

https://brainly.com/question/30507236#

#SPJ11

A 2.0 mm diameter wire of length 20 m has a resistance of 0.25 & the resistivity of the wire is [tex]3.9 * 10^{-8} \Omega[/tex] · m. So option B is correct.

We are given that the wire has a diameter of 2.0 mm, which corresponds to a radius of 1.0 mm. Therefore, the cross-sectional area of the wire is:

[tex]A = \pi r^2 = 3.14 * 10^{-6} m^2.[/tex]

We are also given that the wire has a length of 20 m and a resistance of 0.25 Ω. Plugging these values into the formula, we get:

[tex]0.25 \Omega = (\rho * 20 m) / 3.14 * 10^{-6} m^2[/tex]

Solving for ρ, we get:

[tex]\rho = (0.25 \Omega * 3.14 * 10^{-6} m^2) / 20 m\\\rho = 3.925 * 10^{-8} \Omega .m[/tex]

Therefore, the resistivity of the wire is [tex]3.9 * 10^{-8} \Omega[/tex] · m, Hence the correct option according to the question is B.

To know more about resistivity, here

brainly.com/question/29427458

#SPJ4

To measure 4 gallons of water using only a 3 and 5 gallon jug, you can follow some steps. These steps leaves 4 gallons of water in the 5 gallon jug, which is the desired amount.

The steps are as follow:
1. Fill the 5 gallon jug completely with water.
2. Pour the water from the 5 gallon jug into the 3 gallon jug, filling it up completely.
3. This leaves 2 gallons of water in the 5 gallon jug.
4. Pour out the water from the 3 gallon jug.
5. Pour the 2 gallons of water from the 5 gallon jug into the 3 gallon jug.
6. Fill up the 5 gallon jug completely again.
7. Pour the water from the 5 gallon jug into the 3 gallon jug until it is full.
8. This leaves 1 gallon of water in the 5 gallon jug.
9. Pour out the water from the 3 gallon jug.
10. Pour the 1 gallon of water from the 5 gallon jug into the 3 gallon jug, filling it up completely.
11. This leaves 4 gallons of water in the 5 gallon jug, which is the desired amount.

Learn more about measure at

https://brainly.com/question/28913275

#SPJ11

A tuning fork of frequency 200 hertz can resonate if an incident sound wave has a frequency of 200 hertz.

The phenomenon of resonance occurs when an object vibrates at its natural frequency in response to an external stimulus of the same frequency. In this case, the tuning fork has a natural frequency of 200 Hz. When an incident sound wave with the same frequency of 200 Hz reaches the tuning fork, it causes the fork to vibrate with a larger amplitude.

This resonance amplifies the sound produced by the tuning fork. The length constraint requires the explanation to be concise, which highlights the basic concept of resonance between the incident sound wave and the tuning fork's natural frequency.

To know more about Resonance, refer here :

https://brainly.com/question/28318319#

#SPJ11

When you swim, you create a forward motion by pushing the water backwards. This action is known as propulsion or thrust. The reaction force is the force exerted by the water back onto the swimmer.

This force is equal in magnitude and opposite in direction to the force that the swimmer applies to the water. It allows the swimmer to move forward through the water.

The reaction force also creates a wake behind the swimmer, which is why you can feel the water moving around you when you swim.

The size of the reaction force depends on the speed and power of the swimmer's stroke, as well as the density and viscosity of the water.

Understanding the principles of propulsion and reaction is important for mastering the technique of swimming and improving your overall performance in the water.

To know more about swimmer please visit....

brainly.com/question/30829807

#SPJ11

The approximate temperature of the universe at an age of 5 minutes was around 1 billion degrees Celsius  Kelvin (1 x 10^9 K).

At the beginning of the universe, it was incredibly hot and dense, with temperatures reaching up to 10^32 degrees Celsius. However, as the universe expanded and cooled, the temperature decreased as well. At around 5 minutes after the Big Bang, the temperature had dropped to about 1 billion degrees Celsius. This is still incredibly hot, but it allowed for the formation of the first atomic nuclei, which ultimately led to the formation of the elements we see today.

At the age of 5 minutes, the universe was in the period called the photon epoch. During this time, the temperature of the universe was cooling down as it expanded. We can estimate the temperature at that time using the relation between temperature and time for the early universe, which is given by T ∝ t^(-1/2), where T is the temperature and t is the time.
To know more about temperature visit:

https://brainly.com/question/12869377

#SPJ11

The spring constant of the heavy duty spring is 1.12 x 10^5 N/m.

To solve this problem using conservation of energy, we need to consider the initial potential energy of the elevator cabin when it is at a height of 80 m above the spring, and the final potential energy of the spring when it is compressed by 40 cm. The difference in potential energy will be equal to the energy absorbed by the spring as it is compressed.
Using the formula for gravitational potential energy, the initial potential energy of the elevator cabin is:
PEi = mgh = 1800 kg x 9.81 m/s^2 x 80 m = 1.41 x 10^6 J
When the elevator cabin hits the spring, all of its potential energy is converted into elastic potential energy stored in the spring. The formula for elastic potential energy is:
PEe = 1/2 kx^2
Where k is the spring constant and x is the displacement of the spring from its equilibrium position. In this case, x is equal to 0.4 m (40 cm) since the spring is compressed by 40 cm.
Equating the two potential energies and solving for k, we get:
1/2 kx^2 = mgh
k = 2mgh/x^2
k = 2(1800 kg)(9.81 m/s^2)(80 m)/(0.4 m)^2
k = 1.12 x 10^5 N/m
Therefore, the spring constant of the heavy duty spring is 1.12 x 10^5 N/m.

To know more about spring constant visit:
https://brainly.com/question/29975736
#SPJ11

Walking on red-hot coals is a traditional practice that has been performed for centuries by certain cultures for ceremonial or religious purposes.

While it may seem like a dangerous or painful activity, it is possible to walk on hot coals without getting your feet burned by following some basic guidelines:

Prepare the fire: The fire should be built with small, dry pieces of wood, and the coals should be allowed to burn down until they are glowing red and no longer producing flames.

Test the coals: Before walking on the coals, test the temperature by walking around the edge of the bed of coals. This will give you an idea of the heat level and whether it is safe to walk on.

Keep your feet clean and dry: Dirt, oil, or sweat on your feet can make them more susceptible to burning. Before walking on the coals, make sure your feet are clean and dry.

Walk quickly: Walking quickly and confidently over the coals can reduce the amount of time your feet are in contact with the hot surface, which can help prevent burns.

Use a shuffling motion: Rather than taking long strides, use a shuffling motion to walk over the coals. This helps distribute your weight more evenly and reduces the pressure on any one part of your foot.

Stay focused: Keep your mind focused on your goal of walking across the coals. Avoid distractions and maintain a positive attitude.

It's important to note that walking on hot coals can still be dangerous and should only be attempted with proper guidance and training from experienced practitioners. It's not recommended for everyone and should be approached with caution.

Learn more about red-hot coals here:

https://brainly.com/question/31926998

#SPJ11

Answer:

Explanation:

What is current?

Current is the flow of electric charge through a conductor or a circuit. It is measured in amperes (A), and it is the rate at which charge flows past a given point in a circuit.

How to calculate resistance in a parallel circuit?

In a parallel circuit, the total resistance (Rtotal) can be calculated using the following formula:

1/Rtotal = 1/R1 + 1/R2 + 1/R3 + ...

Where R1, R2, R3, ... are the resistances of each resistor in the circuit. Once you have calculated the total resistance, you can calculate the current in each branch of the circuit using Ohm's law (I = V/R).