When starting a vehicle with an automatic transmission, be sure the gear selector is set in (P)ark or (D)rive.
What are automatic cars?Automatic cars are those who have automatic options for shifting of gears. We do not have to adjust the gears by ourselves.
These cars have mode of Park, if we are moving the car, to start the car we must change it from Park to drive mode.
Thus, the fill the blank is Drive.
Learn more about automatic cars
https://brainly.com/question/14646065
#SPJ1
If a material is found to be in the tertiary phase of creep, the following procedure should be implemented:
a.The component should undergo dye penetrant process and condition monitored.
b.The crack should be stopped, drilled and condition monitoring should be applied.
c.The component should be replaced immediately.
d.None of the above.
When a material is found to be in the tertiary phase of creep, the following procedure should be implemented that is the component should be replaced immediately. Therefore, Option C is correct.
What do you mean by a tertiary degree of creep?Tertiary Creep has an extended creep rate and terminates when the material breaks or ruptures. It is related to each necking and formation of grain boundary voids. The wide variety of possible stress-temperature- time combos is infinite.
Therefore, When a material is found to be in the tertiary phase of creep, the following procedure should be implemented that is the component should be replaced immediately. Option C is correct.
Learn more about creep:
https://brainly.com/question/10565749
#SPJ1
Proper, smooth shifting is important because if you shift before your vehicle is ready
Proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
How to properly shift your gears?A proper, smooth shifting of the gears of an automobile vehicle is very important because shifting them before the vehicle is ready would cause the following:
Jer-king forward. Lock of the drive wheels.Loss of control of the vehicle.As a good driver, proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
Read more on good drivers here: https://brainly.com/question/1071840
#SPJ1
The property that determines a material’s ability to conduct electricity is called?
Answer:
conductivity
Explanation:
Conductivity is the measure of the ease at which an electric charge or heat can pass through a material.
lehighedu
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a ____. A. word-to-word transfer B. file-to-file transfer C. word-to-file transfer D. file-to-word transfer
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a "word-to-word transfer" (Option A)
What is T4:0?
In programming, T4:0 is a time base. Whenever it is set to 1.0, it converts to the timer that counts in seconds.
It is key to note that when enumerated as T4:0 ACC, it is ascribed as an Accumulator address.
Learn more about memory locations at:
https://brainly.com/question/13104134
#SPJ1
In third ange projection draw the plain view, front view and end view.
Answer:
The front view, is a drawing of the block, as if you are looking directly at the front of the object. The side view, is a drawing of the block, when it has been rotated so that one of its sides is now directly in view. The plan view, is a 'birds eye' view, from above.
The toggle (t) flip-flop has one input, clk, and one output, q. on each rising edge of clk, q toggles to the complement of its previous value. draw a schematic for a t flip-flop using a d flip-flop and an inverter.
Answer:
See attached
Explanation:
The next state of a toggle flip-flop is the inverse of the present state. This behavior can be produced using a D flip-flop that has its input connected to the inverse of its output.
__
A schematic is attached.
Steel stirrups in reinforced concrete beams help to resist ________________. Select one: a. Bending b. Deflection c. Shear d. Tension
Answer:
Shear is the answer
hope it helps!
Air is compressed from 20 psia and 70°F to 150 psia in a compressor. The compressor is operated such that the air temperature remains constant. Calculate the change in the specific volume of air as it passes through this compressor.
Answer: -8.51 ft^3/lbm
Explanation:
In this question, to find the change in volume, we will use the ideal gas law.
[tex]\begin{aligned}&n_{1}=1 \text { mole }\\&\mathrm{P}_{1}=20 \mathrm{psia}\\&\mathrm{T}_{1}=70^{\circ} \mathrm{F}\\&T_{1}=(70+460)^{0} \mathrm{R}\\&v_{1}=\frac{\left(0.3704 \frac{psia \cdot_{\text { } ft^{3}}}{l \mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{20 \mathrm{psi}}\\&v_{1}=9.816 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]\begin{aligned}&\mathrm{n}_{2}=1 \text { mole } \\&\mathrm{P}_{2}=150 \mathrm{psia} \\&\mathrm{T}_{1}=\mathrm{T}_{2}=70^{0} \mathrm{~F} \\&\mathrm{~T}_{1}=\mathrm{T}_{2}=(70+460)^{0} \mathrm{R} \\&v_{2}=\frac{\left(0.3704 \frac{\text { psia} \cdot \mathrm{ft}^{3}}{\mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{150 \mathrm{psi}} \\&v_{2}=1.309 \frac{\mathrm{ft}{ }^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]$$The change in volume is,$$\begin{aligned}&\Delta v=v_{2}-v_{1} \\&\Delta v=1.309-9.816 \\&\Delta v=-8.51 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}\text{The negative sign shows that the gas was compressed during this process}[/tex]
Technician A states; that bent lift arms can be straightened.
Technician B states; that worn lift pads should be replaced.
Who is correct?
Both technician "A" and "B"
Neither technician "A" nor "B"
Technician "A" only
Technician "B" only
Draw a circuit diagram connected in a reverse bias showing a p-n material and a battery
The Circuit Diagram is connected in a reverse bias attached below.
What is Reverse Bias?Reverse biased p-n junction diode refers to the method by which a p-n junction diode stops electric current in the presence of applied voltage.
The positive terminal of the battery is connected to the n-type semiconductor material in a reverse biased p-n junction diode, while the negative terminal is connected to the p-type semiconductor material.
Learn more about Reverse biased here:
https://brainly.com/question/14703617
#SPJ1
A _________ can used for both entering and exiting a highway.
The lane that can be used for both entering and exiting a highway is called; A weave lane
How to enter a highway?When it comes to road highways, there are different terminologies that apply such as Acceleration lane, Deceleration Lane, Interchange, Weave lane, Urban roadway e.t.c
However, when it comes to the one that can be used for both entering and exiting a highway, the correct answer will be Weave Lane because it has both an entrance and an exit for an expressway. Traffic may come onto and leave the expressway at the same location.
Read more about road highway at; https://brainly.com/question/12961781
#SPJ12
A trap in the condensate line prevents ____.A) air and foreign material from being drawn up into the drain line. B.) foreign particles
A trap in the condensate line prevents D. All of the above.
What is the idea of the trap?It should be noted that the idea of the condensate drain trap is to use the weight of the water to stop the flow of air.
Based on the information given, all the options are correct. Therefore, the correct option is D.
a. air and foreign material from being drawn up into the drain line
b. additional cooling load from warm air drawn up into the air handler
c. insect invasion of the system
d. all of the above
Learn more about cooling on:
brainly.com/question/13748261
#SPJ12
Heater control valves can not leak coolant
True
False
Heater control valves can not leak coolant
it is true
true, heater control valves DO NOT leak coolant.
:)
Technician A says electrical circuit resistance causes voltage drop. Technician B says high-resistance problems cause an increase in current flow. Who is correct
The person that is correct is Technician A as electrical circuit resistance causes voltage drop.
What is a circuit?It should be noted that an electric circuit is the path through which electric changes flow in order to conduct current.
In this case, the person that is correct is Technician A as electrical circuit resistance causes voltage drop.
Learn more about circuit on:
brainly.com/question/2969220
#SPJ12
ensures that enough pressure is placed on the bearing to keep the shaft from moving around, but not so much that the bearing will run hot and begin to fail. Group of answer choices End play Preload Both A and B Neither A nor B
Preload ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot.
What is preload?Preload can be defined as the load (amount of force) that is generated from an axial interference within a bearing, which causes an elastic deformation between the rolling elements and raceway.
In Engineering, preload is a technique which ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot and failing.
Read more on preload here: https://brainly.com/question/16342676
#SPJ12
what input is required from ADC to allow the INS to calculate W/V?
TAS is an important input which is required from ADC to allow the INS calculate W/V.
What is INS?INS is abbreviation for Inertial Navigation System and it can be defined as a navigation device that makes use of motion sensors, a computer, and rotation sensors, so as to continuously calculate by dead reckoning the velocity, position, and orientation of a moving object.
In the Aviation and Engineering filed, True Airspeed (TAS) is an important input which is required from ADC to allow the Inertial Navigation System (INS) calculate W/V.
Read more on Inertial Navigation System here: https://brainly.com/question/26052911
#SPJ12
the best way to complete a turn requires that you
The best way to complete a turn needs that a person accelerate slowly about halfway through the turn.
What should you do when preparing to turn?If a person wants to prepare to turn, a person need to lower their speed and stay by the far right as soonest.
Therefore, The best way to complete a turn needs that a person accelerate slowly about halfway through the turn.
Learn more about completing a turn from
https://brainly.com/question/595995
#SPJ11
6. During some actual expansion and compression processes in piston–cylinder devices, the gases have been
observed to satisfy the relationship PVn = C, where n and C are constants. Calculate the work done when a
gas expands from 350 kPa and 0.05 m3 to a final volume of 0.25 m3
for the case of n = 1 and 1.5.
During some actual expansion and compression processes in piston-cylinder devices, the gases have been are the P1= P2.
What is the pressure?Pressure is something that has the pressure that is physical and that causes the pressure is piston-cylinder devices.
During a few real enlargements and compression procedures in piston-cylinder devices, the gases were located to meet the connection PV n = C, wherein n and C are constants.
Read more about the pressure :
https://brainly.com/question/25736513
#SPJ1
As described by Bronfenbrenner, the environmental system that consists of links between microsystems is the
As described by Bronfenbrenner, the environmental system that consists of links between microsystems is the mexosystem.
What is a microsystem?It should be noted that a microsystem simply means ten pattern of activities that's expressed by an individual in a setting.
In this case, as described by Bronfenbrenner, the environmental system that consists of links between microsystems is the mexosystem.
Learn more about microsystems on:
brainly.com/question/15727382
#SPJ12
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 tray. If the owner wants a service level a at least 95%?
The number of trays that should be prepared if the owner wants a service level of at least 95% is; 7 trays
How to utilize z-score statistics?We are given;
Mean; μ = 15
Standard Deviation; σ = 5
We are told that the distribution of demand score is a bell shaped distribution that is a normal distribution.
Formula for z-score is;
z = (x' - μ)/σ
We want to find the value of x such that the probability is 0.95;
P(X > x) = P(z > (x - 15)/5) = 0.95
⇒ 1 - P(z ≤ (x - 15)/5) = 0.95
Thus;
P(z ≤ (x - 15)/5) = 1 - 0.95
P(z ≤ (x - 15)/5) = 0.05
The value of z from the z-table of 0.05 is -1.645
Thus;
(x - 15)/5 = -1.645
x ≈ 7
Complete Question is;
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 trays. If the owner wants a service level of at least 95%, how many trays should he prepare (rounded to the nearest whole tray)? Assume doughnuts have no salvage value after the day is complete. 6 5 4 7 unable to determine with the above information.
Read more about Z-score at; https://brainly.com/question/25638875
#SPJ1
the hazards associated with performing hot work include
Answer:
space look at tge explanation
Explanation:
Discuss some of the hazards associated with hot work in confined spaces. Provide specific examples or personal experiences in your response.
The hazards associated with performing hot work include:
HeatUVSparksFumesWhat are the Common Hazards of Hot Work?Note that when working with anything that cause spark or fire, the common hazard are:
Flying sparks. A Flammable swarfExplosive atmospheres, etc.Therefore, The hazards associated with performing hot work include:
HeatUVSparksFumesLearn more about hazards from
https://brainly.com/question/7310653
#SPJ11
what HTML
what is CSS
Hw to create website page
Answer:
HTML (HyperText Markup Language) is the code that is used to structure a web page and its content.
CSS is Cascading Style Sheet.CSS allows you to create great-looking web pages
Explanation:
The results of a _________ test will determine if there is suitable drainage and the size of the drain field that will be required for a septic system.
Answer:
The results of a percolation test will determine if there is suitable drainage and the size of the drain field that will be required for a septic system.
Preferential stress will cause crystals to rotate into a preferred orientation unless the crystals are ________
Answer:
Preferential stress will cause crystals to rotate into a preferred orientation unless the crystals are Equant
Cisco what three best practices can help defend against social engineering attacks?
The three best practices that can help defend against social engineering attacks are:
Do not provide password resets in a c.ha.t window. Resist the urge to click on enticing web links. Educate employees regarding policies.What is Social Engineering?This refers to the art of manipulation of people through social interactions with the aim of getting access to sensitive information that gives unauthorized access.
Hence, we can see that some of the best practices that can be used to defend against social engineering include not clicking on suspicious links, educating people about the dangers, etc.
Read more about social engineering here:
https://brainly.com/question/26072214
#SPJ12
Technician A says that as long as the dog (clutch) teeth of the synchronizer are rounded, the synchronizer can be reused. Technician B says that the synchronizer sleeve should slide smoothly on its splines. Who is correct
Neither of the technicians are correct.
Who is a technician?A technician simply means an individual who looks after the technical equipments in a company.
In this case, the teeth of the synchronizer are not rounded, the synchronizer can be reused. This shows that he is incorrect likewise technician B.
Learn more about technicians on:
brainly.com/question/1548867
#SPJ12
The telescoping arm ABC is used to provide an elevated platform for construction workers. The workers and the platform together have a mass of 220 kg and have a combined center of gravity located directly above C. Assume θ = 20°.
Answer:
That is not a question...
Back-fill used for underground wiring shall not damage ____________ or prevent adequate compaction of fill or contribute to corrosion.
The back-fill used for underground wiring shall not damage the raceways, cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.
What do you mean by underground wiring?A unique form of electric wiring or cable this is designed to be buried in a trench underground is known as Direct-burial cable. The character electric accomplishing wires in the cable are encased in a strong thermoplastic sheath that seals out moisture and protects the accomplishing wires within.
The complete question is given below:
(a) raceways
(b) cables
(c) conductors
(d) all of these
Thus, The back-fill used for underground wiring shall not damage the raceways, cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.
learn more about electrical wiring:
https://brainly.com/question/24786034
#SPJ1
the ____ grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning
Answer:
the jig grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning
An injector pressure drop test to see if the injector is restricted with deposits can be done using an?
An injector pressure drop test to see if the injector is restricted with deposits can be done using an integer test.
What is injector strain drop?Fuel injectors have a glide charge. This glide charge of the injector is rated at a sure strain drop throughout the injector. Meaning the injector glide is say 30#/hr at 42.five PSI. This approach that that injector will glide 30#/hr so long as the strain on the deliver side, minus the strain withinside the manifold is 42.five psiListening or Clicking Test.
Start the engine and permit it to idle. Keep the engine strolling and contact the give-up of a protracted steel screwdriver towards the gas injector. Put your ear on the alternative give up of the screwdriver. A clicking sound approaches the injector's working.
Read more about the injector pressure drop:
https://brainly.com/question/12385665
#SPJ1
