Which of these rotational quantities is analogous to mass in a linear system?

a.
Angle in radians

b.
Angular acceleration

c.
Torque

d.
Rotational inertia

Answers

Answer 1

Answer:

d

Explanation:

i think it is rotational inertia

because analogue of mass in rotational motion is moment of inertia. It plays the same role as mass plays in transnational motion.  

hope it's right & helps !!!!!!!!!


Related Questions

You are to connect resistors R1 andR2, with R1 >R2, to a battery, first individually, then inseries, and then in parallel. Rank those arrangements according tothe amount of current through the battery, greatest first. (Useonly the symbols > or =, for exampleseries>R1=R2>parallel.)

Answers

Answer:

The current is more in the parallel combination than in the series combination.

Explanation:

two resistances, R1 and R2 are connected to a battery of voltage V.

When they are in series,

R = R1 + R2

In series combination, the current is same in both the resistors, and it is given by Ohm's law.

V = I (R1 + R2)

[tex]I = \frac{V}{R_1 + R_2}[/tex]..... (1)

When they are connected in parallel.

the voltage is same in each resistor.

The effective resistance is R.

[tex]R = \frac{R_1R_2}{R_1 + R_2}[/tex]

So, the current is

[tex]I = \frac{V(R_1+R_2)}{R_1 R_2}[/tex]..... (2)

So, the current is more is the parallel combination.

A physics instructor wants to project a spectrum of visible-light colors from 400 nm to 700 nm as part of a classroom demonstration. She shines a beam of white light through a diffraction grating that has 600 lines per mm, projecting a pattern on a screen 2.9 m behind the grating.

Required:
How wide is the spectrum corresponding to m=1?

Answers

Answer:

  Dr = 263 10⁻⁶ m

Explanation:

The diffraction pattern for constructive interference is described by

        a sin θ = m λ

in this it indicates that the order of diffraction is m = 1

Let's use a direct proportion rule to find the separation of two slits. If there are 600 lines in 1 me, what is the distance between 2 slits

   a = 2 lines 1/600

   a = 2/600

    a = 3.33 10⁻³ mm = 3.33 10⁻⁴ cm

let's use trigonometry

      tan θ = y / L

as the measured angles are small

      tan θ = sin θ / cos θ sin θ

      sin θ = y / L

we substitute

     a  y/L = λ

     y = λ L / a

for λ = 400 10-9 m

      I = 400 10⁻⁹ 2.9 / 3.33 10⁻³

      i = 346.89 10⁻⁶ m

f

or λ = 700 nm

        y_f = 700 10⁻⁻⁹ 2.9 / 3.33 10⁻³

        y_f = 609.609 10⁻⁶ m

the separation of this spectrum

        Δr = v_f - i

        Dr = (609.609 - 346)  10 ⁻⁶

        Dr = 263 10⁻⁶ m

Which one of the following physical quantities has its S.I. unit m/s?
(i) Acceleration
(ii) Velocity
(iii) Force
(iv) Density​

Answers

Answer:

velocity is the answer of this question.

Answer:

Velocity is the right answer ok

From the given picture What's the force? And where did it happen? (at least 2 forces)

Answers

Answer:

the force happens on the wall and couch

Explanation:

she is using her arm strength to lift and hold

Describe how the words Science and optics would appear when viewed in a plane mirror?

Answers

Answer:

Lateral inversion will occur in a plane mirror.

Explanation:

When words are displayed in a plane or flat mirror, the result is that if the words are displayed left, they change to right and if they were normally displayed right, they change to left. This phenomenon is known as lateral inversion. So, this will apply to the words, Science and optics. Only the sides will be interchanged.

A plane mirror reflects light, therefore, the image that is produced by it remains the same size. The image produced will not appear upside down. Only the sides will be interchanged.

While standing at the edge of the roof of a building, a man throws a stone upward with an initial speed of 6.63 m/s. The stone subsequently falls to the ground, which is 14.5 m below the point where the stone leaves his hand.

At what speed does the stone impact the ground? Ignore air resistance and use =9.81 m/s2 for the acceleration due to gravity.
How much time is the stone in the air?
elapsed time:

Answers

Answer:

Speed=28.1m/s(to 3s.f.) , Time=2.19s(to 3s.f.)

Explanation:

Time=Distance/Speed

=14.5/6.63

=2.19s(to 3s.f.)

Acceleration=Final Velocity(v)-Initial Velocity(u)/Time

9.81=v-6.63/2.19

v-6.63=21.5

v=28.1m/s

1 Poin Question 4 A 85-kg man stands in an elevator that has a downward acceleration of 2 m/s2. The force exerted by him on the floor is about: (Assume g = 9.8 m/s2) А ON B 663 N C) 833 N D) 1003 N​

Answers

Answer:

D) 1003 N​

Explanation:

Given the following data;

Mass of man = 85 kg

Acceleration of elevator = 2 m/s²

Acceleration due to gravity, g = 9.8 m/s²

To find the force exerted by the man on the floor;

Force = mg + ma

g A small object of mass 2.5 g and charge 18 uC is suspended motionless above the ground when immersed in a uniform electric field perpendicular to the ground. What is the magnitude and direction of the electric field

Answers

Answer: [tex]1361.11\ N/C,\text{upward}[/tex]

Explanation:

Given

Mass of particle is [tex]m=2.5\ gm[/tex]

Charge of particle is [tex]q=18\ \mu C[/tex]

Electrostatic force must balance the weight of the particle

[tex]\lim_{n \to \infty} a_n \Rightarrow mg=qE\\\\\Rightarrow E=\dfrac{2.5\times 9.8\times 10^{-3}}{18\times 10^{-6}}\\\\\Rightarrow E=1361.1\ N/C[/tex]

Direction of the electric field is in upward direction such that it opposes the gravity force.

The Michelson-Morley experiment was designed to measure Group of answer choices the velocity of the Earth relative to the ether. the relativistic momentum of the electron. the relativistic mass of the electron. the acceleration of gravity on the Earth's surface. the relativistic energy of the electron.

Answers

Answer:

The Michelson-Morley was designed to detect the motion of the earth through the ether.

No such relation was found and the speed of light is assumed to be the same in all reference frames.

The Michelson-Morley experiment was designed to measure: A. the velocity of the Earth relative to the ether.

Michelson-Morley experiment is an experiment which was first performed in Germany by the American physicist named, Albert Abraham Michelson between 1880 to 1881.

However, the experiment was later modified and refined by Michelson and Edward W. in 1887.

The main purpose of the Michelson-Morley experiment was to measure the velocity of planet Earth relative to the luminiferous ether, which is a medium in space that is hypothetically said to carry light waves.

In conclusion, the Michelson-Morley experiment was designed to measure the velocity of the Earth relative to the hypothetical luminiferous ether.

Read more: https://brainly.com/question/13187705

b. A bird in air looks a fish vertically below it inside the water from a distance 5m from surface of water and fish lies at depth 4m from the surface of water. IF Mw= 4/3, what is the distance of fish as observed by bird?

Answers

Answer:

the distance of the fish (as  seen by the bird) is greater than the actual distance.

Reason-

it is due to the apparent depth and differences between the refractive indices.

Have a nice day!

What is the incorrect statement regarding the isotopes of the same element?
1) Electronic configuration is equal
2) Mass number is equal
3) Number of protons are equal
4) Number of electrons are equal​

Answers

Answer:

1231

Explanation:

Develop a hypothesis regarding one factor you think might affect the period of a pendulum or an oscillating mass on a spring. Potential factors include the mass, the spring constant, and the length of the pendulum's string. Write down your hypothesis. 2. Design a controlled experiment to test your hypothesis. Take extreme care to keep all factors constant except the variable you are testing.

Answers

Answer:

A hypothesis for the period of a pendulum is:

"The period of the pendulum varies with its length"

Explanation:

A hypothesis for the period of a pendulum is:

"The period of the pendulum varies with its length"

To test this hypothesis we can carry out a measurement of a simple pendulum keeping the angle fixed, in general the angle used is about 5º since when placing this value in radiand and the sine of this angle they differ little <5%. therefore measured the time of some oscillations, for example about 10 oscillations, changing the length of the pendulum to test the hypothesis.

If the hypothesis and the model used is correct, the relationship to be tested is

              T² =(4π² /g)   L  

by making a graph of the period squared against the length if obtaining, os a line, the hypothesis is tested.

A rock is suspended by a light string. When the rock is in air, the tension in the string is 37.8 N. When the rock is totally immersed in water, the tension is 32.0 N. When the rock is totally immersed in an unknown liquid, the tension is 20.2 N. What is the Density of the unknown liquid?

Answers

When the rock is suspended in the air, the net force on it is

F₁ = T₁ - m₁g = 0

where T₁ is the magnitude of tension in the string and m₁g is the rock's weight. So

T₁ = m₁g = 37.8 N

When immersed in water, the tension reduces to T₂ = 32.0 N. The net force on the rock is then

F₂ = T₂ + B₂ - m₁g = 0

where B₂ is the magnitude of the buoyant force. Then

B₂ = m₁g - T₂ = 37.8 N - 32.0 N = 5.8 N

B₂ is also the weight of the water that was displaced by submerging the rock. Let m₂ be the mass of the displaced water; then

5.8 N = m₂g   ==>   m₂ ≈ 0.592 kg

If one takes the density of water to be 1.00 g/cm³ = 1.00 × 10³ kg/m³, then the volume of water V that was displaced was

1.00 × 10³ kg/m³ = m₂/V   ==>   V ≈ 0.000592 m³ = 592 cm³

and this is also the volume of the rock.

When immersed in the unknown liquid, the tension reduces further to T₃ = 20.2 N, and so the net force on the rock is

F₃ = T₃ + B₃ - m₁g = 0

which means the buoyant force is

B₃ = m₁g - T₃ = 37.8 N - 20.2 N = 17.6 N

The mass m₃ of the liquid displaced is then

17.6 N = m₃g   ==>   m₃ ≈ 1.80 kg

Then the density ρ of the unknown liquid is

ρ = m₃/V ≈ (1.80 kg)/(0.000592 m³) ≈ 3040 kg/m³ = 3.04 g/cm³

The lines in the emission spectrum of hydrogen result from __________.
a. energy given off in the form of visible light when an electron moves from a higher energy state to a lower energy state
b. protons given off when hydrogen burns
c. electrons given off by hydrogen as it cools
d. electrons given off by hydrogen when it burns
e. decomposing hydrogen atoms.

Answers

Answer:

Option (a) is correct.

Explanation:

The lines in the emission spectrum of hydrogen is due to the transfer of electrons form higher energy levels to the lower energy levels.

When the electrons transfer from one level of energy that is higher level of energy to the other means to the lower level of energy then they emit some photons which having the frequency or the wavelength in the visible region.

What is the energy of a photon with a frequency of 3.6 × 1015 Hz? Planck’s constant is 6.63 × 10–34 J•s.

1.8 × 10–49 J
2.4 × 10–19 J
1.8 × 10–18 J
2.4 × 10–18 J

Answers

Frequency =v=3.6×10^15Hz

We know

[tex]\boxed{\sf E=hv}[/tex]

[tex]\\ \sf\longmapsto E=6.63\times 10^{-34}J\times 3.6\times 10^{15}s^{-1}[/tex]

[tex]\\ \sf\longmapsto E=23.86\times 10^{-19}J[/tex]

[tex]\\ \sf\longmapsto E=2.38\times 10^{-18}J[/tex]

[tex]\\ \sf\longmapsto E=2.4\times 10^{-18}J[/tex]

Answer:

D!!!!!

Explanation:

Your physics TA has a far point of 0.759 m from her eyes and is able to see distant objects in focus when wearing glasses with a refractive power of −1.35 D. Determine the distance between her glasses and eyes.

Answers

Answer:

[tex]d=0.019m[/tex]

Explanation:

From the question we are told that:

Far point [tex]x=0.759m[/tex]

Refractive power [tex]P=-1.35 D.[/tex]

Generally, the equation for Focal length is mathematically given by

[tex]F=\frac{1}{P}[/tex]

[tex]F=\frac{1}{-1.35}[/tex]

[tex]F=-0.74m[/tex]

Therefore

[tex]\frac{1}{f}=\frac{1}{u}+\frac{1}{v}[/tex]

Where

[tex]u=o[/tex]

[tex]\frac{1}{-0.74}=\frac{1}{0}+\frac{1}{v}[/tex]

[tex]v=-0.74m[/tex]

Therefore,The between her glasses and eyes

[tex]d=x-v[/tex]

[tex]d=0.759-0.74m[/tex]

[tex]d=0.019m[/tex]

In the lab room, you are sitting in an office chair with wheels while holding onto a force sensor, and the chair is at rest. One end of a lightweight string is attached to the force sensor, and your lab partner is holding the other end of the string. Your lab partner then moves away from you, pulling on the string. Describe how your lab partner must move for the force sensor to read a constant force. Explain

Answers

Answer:

a circular motion a constant force can be measured

Explanation:

The force is expressed by the relation

         F = m a

The bold are vectros.

Therefore, when your partner moves away, he has a reading of a force, so that this force remains constant there must be an acceleration at all times, one way to achieve these is with a circular motion with constant speed, in this case the module of the velocity is constant, but the direction changes at each point and there is an acceleration at each point.

Consequently with a circular motion a constant force can be measured

The force depends on the acceleration, hence the force will be constant during the circular motion for constant acceleration.

What is Force?

A force can be defined as an influence that can change the motion of an object. The force is expressed by the relation

[tex]F = m a[/tex]

The force is dependent on the mass and acceleration of the object. The acceleration is a vector quantity, so the force will be a vector quantity.

Given that, in a lab room, you are sitting on a wheelchair at one end and at the other end, lab partner then moves away from you, pulling on the string that is attached to the force sensor.

When the lab partner moves away and pulled the string, there must be an acceleration during the motion. If the lab partner moves in a circular motion, then the velocity is constant but the direction changes at each point. There is an acceleration at each point that will be constant.  

As the force depends on the acceleration, hence the force will be constant during the circular motion for constant acceleration.

To know more about the force, follow the link given below.

https://brainly.com/question/26115859.

Difference between uniform motion and non uniform motion

Answers

Answer:

When an object covers equal distance in an equal interval of time, it is uniform motion but when an object covers unequal distance in an equal interval of time, it is called non uniform motion.

With respect to a right handed Cartesian coordinate system and given that . A = 4i + k and B = 2i + j _ 3k find A cross B

Answers

Using the left-hand rule,

[tex](4\,\vec\imath+\vec k)\times(2\,\vec\imath+\vec\jmath-3\,\vec k) = \begin{vmatrix}\vec\imath&\vec\jmath&\vec k\\4&0&1\\2&1&-3\end{vmatrix} = -\vec\imath+14\,\vec\jmath+4\,\vec k[/tex]

Then in the right-handed rectangular coordinates, the cross product is the negative of this,

[tex]\boxed{\vec\imath-14\,\vec\jmath-4\,\vec k}[/tex]

An airplane which intends to fly due south at 250 km/hr experiences a wind blowing westward at 40 km/hr. What is the actual speed of the airplane relative to the ground? ​

Answers

Answer:

simple is rumple a daily ok I'll be

In December of 2011 they announced that a planet has been discovered in a habitable zone around a
star! It has clouds! It has twice the radius of the earth, but with the same density as earth, about 5.515 × 10^3kg/m3
. Find the new acceleration of gravity on the surface of this planet.

Answers

Explanation:

The density of earth [tex]\rho_E[/tex] is given by

[tex]\rho_E = \dfrac{M_E}{\left(\frac{4\pi}{3}R_E^3\right)}[/tex]

and in terms of this density, we can write the acceleration due to gravity on earth as

[tex]g_E =G\dfrac{M_E}{R_E^2} = \dfrac{4\pi G}{3}\rho_ER_E[/tex]

Similarly, the acceleration due to gravity [tex]g_P[/tex] on this new planet is given by

[tex]g_P = G\dfrac{M_P}{R_P^2} = G\dfrac{\frac{4\pi}{3}R_p^3\rho_P}{R_P^2}[/tex]

[tex]\:\:\:\:\:= \dfrac{4\pi G}{3}\rho_PR_P[/tex]

We know that this planet has the same density as earth and has a radius 2 times as large. We can then rewrite [tex]g_P[/tex] as

[tex]g_P = \dfrac{4\pi G}{3}\rho_E(2R_E)[/tex]

[tex]\:\:\:\:\:= 2\left(\dfrac{4\pi G}{3}\rho_ER_E\right) = 2g_E[/tex]

[tex]\:\:\:\:\:= 2(9.8\:\text{m/s}^2) = 19.6\:\text{m/s}^2[/tex]

The capacitor is now disconnected from the battery, and the dielectric plate is slowly removed the rest of the way out of the capacitor. Find the new energy of the capacitor, U3. Express your answer numerically in joules.

Answers

The question is incomplete. The complete question is :

A dielectric-filled parallel-plate capacitor has plate area A = 10.0 cm2 , plate separation d = 10.0 mm and dielectric constant k = 3.00. The capacitor is connected to a battery that creates a constant voltage V = 15.0 V . Throughout the problem, use ϵ0 = 8.85×10−12 C2/N⋅m2 .

Find the energy U1 of the dielectric-filled capacitor. I got U1=2.99*10^-10 J which I know is correct. Now I need these:

1. The dielectric plate is now slowly pulled out of the capacitor, which remains connected to the battery. Find the energy U2 of the capacitor at the moment when the capacitor is half-filled with the dielectric.

2. The capacitor is now disconnected from the battery, and the dielectric plate is slowly removed the rest of the way out of the capacitor. Find the new energy of the capacitor, U3.

Solution :

Given :

[tex]A = 10 \ cm^2[/tex]

   [tex]$=0.0010 \ m^2$[/tex]

d = 10 mm

  = 0.010 m

Then, Capacitance,

[tex]$C=\frac{k \epsilon_0 A}{d}$[/tex]

[tex]$C=\frac{8.85 \times 10^{12} \times 3 \times 0.0010}{0.010}$[/tex]

[tex]$C=2.655 \times 10^{12} \ F$[/tex]

[tex]$U_1 = \frac{1}{2}CV^2$[/tex]

[tex]$U_1 = \frac{1}{2} \times 2.655 \times 10^{-12} \times (15V)^2$[/tex]

[tex]$U_1=2.987 \times 10^{-10}\ J$[/tex]

Now,

[tex]$C_k=\frac{1}{2} \frac{k \epsilon_0}{d} \times \frac{A}{2}$[/tex]

And

[tex]$C_{air}=\frac{1}{2} \frac{\epsilon_0}{d} \times \frac{A}{2}$[/tex]

In parallel combination,

[tex]$C_{eq}= C_k + C_{air}$[/tex]

[tex]$C_{eq} = \frac{1}{2} \frac{\epsilon_0 A}{d}(1+k)$[/tex]

[tex]$C_{eq} = \frac{1}{2} \times \frac{8.85 \times 10^{-12} \times 0.0010}{0.01} \times (1+3)$[/tex]

[tex]$C_{eq} = 1.77 \times 10^{-12}\ F$[/tex]

Then energy,

[tex]$U_2 =\frac{1}{2} C_{eq} V^2$[/tex]

[tex]$U_2=\frac{1}{2} \times 1.77 \times 10^{-12} \times (15V)^2$[/tex]

[tex]$U_2=1.99 \times 10^{-10} \ J$[/tex]

b). Now the charge on the [tex]\text{capacitor}[/tex] is :

[tex]$Q=C_{eq} V$[/tex]

[tex]$Q = 1.77 \times 10^{-12} \times 15 V$[/tex]

[tex]$Q = 26.55 \times 10^{-12} \ C$[/tex]

Now when the capacitor gets disconnected from battery and the [tex]\text{dielectric}[/tex] is slowly [tex]\text{removed the rest}[/tex] of the way out of the [tex]\text{capacitor}[/tex] is :

[tex]$C_3=\frac{A \epsilon_0}{d}$[/tex]

[tex]$C_3 = \frac{0.0010 \times 8.85 \times 10^{-12}}{0.01}$[/tex]

[tex]$C_3=0.885 \times 10^{-12} \ F$[/tex]

[tex]$C_3 = 0.885 \times 10^{-12} \ F$[/tex]

Without the dielectric,

[tex]$U_3=\frac{1}{2} \frac{Q^2}{C}$[/tex]

[tex]$U_3=\frac{1}{2} \times \frac{(25.55 \times 10^{-12})^2}{0.885 \times 10^{-12}}$[/tex]

[tex]$U_3=3.98 \times 10^{-10} \ J$[/tex]

3) A lead bullet initially at 30 C just melts upon striking a target. Assuming that all of the initial kinetic energy of the bullet goes into the internal energy of the bullet to raise its temperature and melt it, calculate the speed of the bullet upon impact. (Specific heat of lead is 0.128 kJ/kg K and lead latent heat of fusion is 24.7 kJ/Kg and melting point of lead is 600 K).

Answers

Answer:

The speed of bullet is 354.2 m/s

Explanation:

initial temperature, T = 30 degree C

specific heat, c = 128 J/kg K

Latent heat, L = 24.7 x 1000 J/kg

melting point = 600 K = 327 degree C

Let the mass is m and the speed is v.

Kinetic energy = heat used to increase the temperature + Heat used to melt

[tex]\frac{1}{2} mv^2 = m c (T' - T) + m L\\\\0.5 v^2 = 128 \times (327 - 30) + 24.7\times 1000\\\\0.5 v^2 = 38016 + 24700 \\\\0.5 v^2 = 62716\\\\v = 354.2 m/s[/tex]

A car is traveling at 118 km/h when the driver sees an accident 85 m ahead and slams on the brakes. What minimum constant deceleration is required to stop the car in time to avoid a pileup

Answers

Answer:

The constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²

Explanation:

From the question, the car is traveling at 118 km/h, that is the initial velocity, u = 118km/h

The distance between the car and the accident at the moment when the driver sees the accident is 85 m, that is s = 85 ,

Since the driver slams on the brakes and the car will come to a stop, then the final velocity, v = 0 km/h = 0 m/s

First, convert 118 km/h to m/s

118 km/h = (118 × 1000) /3600 = 32.7778 m/s

∴ u = 32.7778 m/s

Now, to determine the deceleration, a, required to stop,

From one of the equations of motion for linear motion,

v² = u² + 2as

Then

0² = (32.7778)² + 2×a×85

0 = 1074.3841 + 170a

∴ 170a = - 1074.3841

a = - 1074.3841 / 170

a = - 6.3199

a ≅ - 6.32 m/s²

Hence, the constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²

A battery charges a parallel-plate capacitor fully and then is removed. The plates are then slowly pulled apart. What happens to the potential difference between the plates as they are being separated?
A) It increases.
B) It decreases.
C) It remains constant.
D) It cannot be determined from the information given.

Answers

The correct answer is A) it increases

You're carrying a 3.0-m-long, 24 kg pole to a construction site when you decide to stop for a rest. You place one end of the pole on a fence post and hold the other end of the pole 35 cm from its tip. How much force must you exert to keep the pole motionless in a horizontal position?

Answers

Answer:

[tex]F=133N[/tex]

Explanation:

From the question we are told that:

Length [tex]l=3.0m[/tex]

Mass [tex]m=24kg[/tex]

Distance from Tip [tex]d=35cm[/tex]

Generally, the equation for Torque Balance is mathematically given by

[tex]mg(l/2)=F(l-d)[/tex]

[tex]2*9.81(3/2)=F(3-35*10^-2)[/tex]

Therefore

[tex]F=133N[/tex]

A skateboarder travels on a horizontal surface with an initial velocity of 3.6 m/s toward the south and a constant acceleration of 1.8 m/s^2 toward the east. Let the x direction be eastward and the y direction be northward, and let the skateboarder be at the origin at t=0.

a. What is her x position at t=0.60s?
b. What is her y position at t=0.60s?
c. What is her x velocity component at t=0.60s?
d. What is her y velocity component at t=0.60s?

Answers

Answer:

a) The x-position of the skateboarder is 0.324 meters.

b) The y-position of the skateboarder is -2.16 meters.

c) The x-velocity of the skateboard is 1.08 meters per second.

d) The y-velocity of the skateboard is -3.6 meters per second.

Explanation:

a) The x-position of the skateboarder is determined by the following expression:

[tex]x(t) = x_{o} + v_{o,x}\cdot t + \frac{1}{2}\cdot a_{x} \cdot t^{2}[/tex] (1)

Where:

[tex]x_{o}[/tex] - Initial x-position, in meters.

[tex]v_{o,x}[/tex] - Initial x-velocity, in meters per second.

[tex]t[/tex] - Time, in seconds.

[tex]a_{x}[/tex] - x-acceleration, in meters per second.

If we know that [tex]x_{o} = 0\,m[/tex], [tex]v_{o,x} = 0\,\frac{m}{s}[/tex], [tex]t = 0.60\,s[/tex] and [tex]a_{x} = 1.8\,\frac{m}{s^{2}}[/tex], then the x-position of the skateboarder is:

[tex]x(t) = 0\,m + \left(0\,\frac{m}{s} \right)\cdot (0.60\,s) + \frac{1}{2}\cdot \left(1.8\,\frac{m}{s^{2}} \right) \cdot (0.60\,s)^{2}[/tex]

[tex]x(t) = 0.324\,m[/tex]

The x-position of the skateboarder is 0.324 meters.

b) The y-position of the skateboarder is determined by the following expression:

[tex]y(t) = y_{o} + v_{o,y}\cdot t + \frac{1}{2}\cdot a_{y} \cdot t^{2}[/tex] (2)

Where:

[tex]y_{o}[/tex] - Initial y-position, in meters.

[tex]v_{o,y}[/tex] - Initial y-velocity, in meters per second.

[tex]t[/tex] - Time, in seconds.

[tex]a_{y}[/tex] - y-acceleration, in meters per second.

If we know that [tex]y_{o} = 0\,m[/tex], [tex]v_{o,y} = -3.6\,\frac{m}{s}[/tex], [tex]t = 0.60\,s[/tex] and [tex]a_{y} = 0\,\frac{m}{s^{2}}[/tex], then the x-position of the skateboarder is:

[tex]y(t) = 0\,m + \left(-3.6\,\frac{m}{s} \right)\cdot (0.60\,s) + \frac{1}{2}\cdot \left(0\,\frac{m}{s^{2}}\right)\cdot (0.60\,s)^{2}[/tex]

[tex]y(t) = -2.16\,m[/tex]

The y-position of the skateboarder is -2.16 meters.

c) The x-velocity of the skateboarder ([tex]v_{x}[/tex]), in meters per second, is calculated by this kinematic formula:

[tex]v_{x}(t) = v_{o,x} + a_{x}\cdot t[/tex] (3)

If we know that [tex]v_{o,x} = 0\,\frac{m}{s}[/tex], [tex]t = 0.60\,s[/tex] and [tex]a_{x} = 1.8\,\frac{m}{s^{2}}[/tex], then the x-velocity of the skateboarder is:

[tex]v_{x}(t) = \left(0\,\frac{m}{s} \right) + \left(1.8\,\frac{m}{s} \right)\cdot (0.60\,s)[/tex]

[tex]v_{x}(t) = 1.08\,\frac{m}{s}[/tex]

The x-velocity of the skateboard is 1.08 meters per second.

d) As the skateboarder has a constant y-velocity, then we have the following answer:

[tex]v_{y} = -3.6\,\frac{m}{s}[/tex]

The y-velocity of the skateboard is -3.6 meters per second.

Electromagnetic radiation with a wavelength of 525 nm appears as green light to the human eye. Calculate the frequency of this light. Be sure to include units in your answer.

Answers

Answer:

5.71×10¹⁴ Hz

Explanation:

Applying,

v = λf................. Equation 1

Where v = speed of the electromagnetic radiation, λ = wavelength of the electromagnetic radiation, f = frequency

make f the subject of the equation

f = v/λ............. Equation 2

From the question,

Given: λ = 525 nm = 5.25×10⁻⁷ m,

Constant: Speed of electromagnetic wave (v) = 3.0×10⁸ m/s

Substitute these values into equation 2

f = (3.0×10⁸)/(5.25×10⁻⁷)

f = 5.71×10¹⁴ Hz

Hence the frequency of light is 5.71×10¹⁴ Hz

two electrons are separated by 1.10m, What is the magnitude of the electric force each electron exerts on the other?

Answers

Answer:

4.56×10¯⁷¹ N

Explanation:

From the question given above, the following data were obtained:

Distance apart (r) = 1.10 m

Force (F) =?

NOTE:

Gravitational constant (G) = 6.67×10¯¹¹ Nm² /Kg²

Mass of electron = 9.1×10¯³¹ Kg

Mass of the two elections = M₁ = M₂ = 9.1×10¯³¹ Kg

Thus, we can obtain the force of attraction between the two elections as illustrated below:

F = GM₁M₂ / r²

F = 6.67×10¯¹¹ × (9.1×10¯³¹)² / (1.1)²

F = 4.56×10¯⁷¹ N

Thus, the force of attraction between the two elections is 4.56×10¯⁷¹ N

1. A body moving with uniform acceleration of 10 m/s2 covers a distance of 320 m. if its initial velocity was 60 m/s. Calculate its final velocity.​

Answers

Answer:

v² = u² + 2as

v² = 3600 + 6400

v² = 10000

v = 100

Explanation:

final velocity is 100 m/s

initial velocity=u=60m/sAcceleration=10m/s^2=aDistance=s=320mFinal velocity=v

According to third equation of kinematics

[tex]\boxed{\sf v^2-u^2=2as}[/tex]

[tex]\\ \sf\longmapsto v^2=u^2+2as[/tex]

[tex]\\ \sf\longmapsto v^2=(60)^2+2(10)(320)[/tex]

[tex]\\ \sf\longmapsto v^2=3600+3400[/tex]

[tex]\\ \sf\longmapsto v^2=10000[/tex]

[tex]\\ \sf\longmapsto v=\sqrt{10000}[/tex]

[tex]\\ \sf\longmapsto v=100m/s[/tex]

Other Questions
I need help! A car has a mass of 1,200 kg and the road can provide a maximum force of 24 kN on the car what is the maximum acceleration? Determine what type of model best fits the given situation: A $500 raise in salary each year. A. exponential B. quadratic C. none of these D. linear ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Lab Report Evidence of Plate MotionIts time to complete your Lab Report. Save the lab to your computer with the correct unit number, lab name, and your name at the end of the file name (e.g., U4_ Lab_EvidenceOfPlateMotion_Alice_Jones.doc).Introduction1.What was the purpose of the experiment?Type your answer here:2.How does hot spot theory explain how the Hawaiian Islands formed?Type your answer here:Experimental Methods1.What tools did you use to collect your data?Type your answer here:2.Describe the procedure that you followed to collect your data.Type your answer here:Data and Observations1.Record your observations. Include a data table with the names of the volcanoes, their distance from Kilauea, and their ages.Type your answer here:2.Make a graph that shows the distance between the volcanoes and Kilauea versus the ages of the volcanoes. You may plot your data on the template provided or use a spreadsheet program to make a graph.Type your answer here:However get 100 points and brainlest Unknown element x has four energy levels, five valence electrons, and is a metalloid. What is element x?. The following table shows the number of visitors to Yellowstone National Park from 2000 to 2006.What was the percent of change in the number of tourists between 2000 and 2001? When planning an investigation, the _______ are the steps you take to complete an investigation. If 3/4 of one of the acute angles of a right-angled triangle is 15 1/4 larger than 1/6 of the other, find the acute angles. The orange had 12 sections. Dave ate of them. How 2/3 many sections are left? help with this question, please! make a sentence using : surfing, suit, black, expensive, workout, towels, ugly, and dog. Match the expression to the method needed to evaluate (will give brainlest) A solution that contains 3 grams of solute dissolved in 100 millimeters of solution is:a) 3% m / mb) 3% m / vc) 10% m / v I do not know how to do this Factorise3-x^2Someone answer this question please You know that a circuit is a path along which electrical charges can flow. In this activity, you are going to illustrate that the flow of electricity needs a closed circuit. Your task is draw the wires that connect these objects in order to create a closed circuit. In the space provided, write one sentence that identifies why this circuit allows electrical charges to flow. Be sure to include each object in your answer. Your friend says that the equations y - 9 = -5(x + 2) and y = -5x 19 represent two different lines. Is your friend correct? Explain. -2(x+1)= -2+5How you solve that? because of a dispute between owners and players, what has just occurred in major league baseball for the first time since the 1994 and 1995 seasons? 7.2 divided by 450 !!