Higher mass stars are able to use a higher fraction of their mass for fusion due to the increased gravitational pressure within their cores. The gravitational force in massive stars is stronger, causing a greater compression of the core. This compression results in higher temperatures and pressures, enabling fusion reactions to occur more efficiently.
The higher temperature and pressure facilitate the fusion of heavier elements, such as carbon, nitrogen, and oxygen, which require more energy to overcome their stronger electrostatic repulsion. In contrast, lower mass stars primarily undergo fusion of lighter elements like hydrogen and helium.
Additionally, higher mass stars have longer lifetimes, allowing them to sustain fusion for a more extended period. This extended duration provides more time for the fusion reactions to proceed, effectively utilizing a larger fraction of their mass for energy production.
To know more about stars refer here
brainly.com/question/29008154
#SPJ11
Remaining Time 1 hour, 38 minutes, 08 seconds. Question completion Status Moving to the next question prevents changes to this answer Question 1935 Question 19 1 points (CLO 2) A parallel plates capacitor is composed of two plates in form of a square of side 8.2.8 cm each and separated by distance - mm Themistor tretween the two the vacuum What is the energy stored in the capacitor in unit "J" pico Joula) ft in connected to a battery of potential difference AV-5077 Enter your answer as positive decimal number with digit after the decimal point. Don't enter the unit o Question 19 Moving to the next question prevents changes to this answer S 6 8
The energy stored in the capacitor in picojoules (pJ) is given by the expression 1.86 x 10⁴ x (AV - 5077)². Just substitute the value of V to get the result.
The given question can be solved using the formula E = 0.5 x C x V², where E is the energy stored in the capacitor, C is the capacitance of the capacitor, and V is the potential difference across the capacitor. Therefore, we can find the energy stored in the capacitor as follows:
Given data: The side of each plate of the capacitor, a = 8.2 cm = 0.082 m The separation distance between the plates, d = - mm = -0.008 m The potential difference across the capacitor, V = AV - 5077 The capacitance of a parallel plate capacitor is given by C = εA/d, where ε is the permittivity of free space, and A is the area of each plate.ε = 8.854 × 10⁻¹² F/m² (permittivity of free space)A = a² = (0.082 m)² = 0.006724 m²d = -0.008 mC = εA/d = (8.854 × 10⁻¹² F/m²)(0.006724 m²)/(-0.008 m) = -7.438 × 10⁻¹² FNow, we can substitute the given values into the formula for energy and solve for E: E = 0.5 x C x V²E = 0.5 x (-7.438 × 10⁻¹² F) x (AV - 5077)²E = 1.86 x 10⁻⁸ x (AV - 5077)²We can convert this to picojoules (pJ) by multiplying by 10¹²: E = 1.86 x 10⁴ x (AV - 5077)²
Therefore, the energy stored in the capacitor in picojoules (pJ) is given by the expression 1.86 x 10⁴ x (AV - 5077)². Just substitute the value of V to get the result.
To know more about potential differences please refer:
https://brainly.com/question/24142403
#SPJ11
X1. What is the non-destructive method of testing method for defectsusing a magnet yoke? X.2 When cold rolling a metal the hardness increases Explain why? X.3 What heat treatment should be used to produce the hardest surface on a metal? X.4 Can Brass be ameal at 500F? Why? X.5 Which Casting Process can Make the largest Castings?
1. The non-destructive testing (NDT) method is a test that is carried out to detect and evaluate flaws in materials. It is a testing technique that does not damage the object being tested. The non-destructive testing method that uses a magnet yoke for the identification of defects in metal components is known as Magnetic particle testing (MPT).
2. Cold rolling of metals increases the hardness of the metal by causing dislocations and deformations in the crystal lattice of the metal. During cold rolling, the metal is deformed below its recrystallization temperature, which hardens the metal and makes it stronger.
3. To produce the hardest surface on metal, hardening heat treatment methods such as flame hardening, induction hardening, and carburizing can be used.
4. Yes, Brass can be a meal at 500°F because it is a metal alloy that is composed of copper and zinc, and it has a melting point of around 900 to 940°F.
5. The casting process that can make the largest castings is known as sand casting. Sand casting is a process of making metal castings by pouring molten metal into a sand mold. Sand casting is the most widely used casting process because it is capable of producing castings of virtually any size and shape.
learn more about castings here
https://brainly.com/question/25957212
#SPJ11
The rings of Saturn are composed of chunks of ice that orbit the
planet. The inner radius of the rings is 73,000 km, and the outer
radius is 170,000 km.
Part A) Find the period of an orbiting chunk of
The period of an orbiting chunk of ice in the rings of Saturn is approximately 333,170.7 years.
The period of an orbiting chunk of ice can be found using Kepler's third law, which states that the square of the period of an orbiting object is proportional to the cube of its average distance from the planet's center.
To find the period, we first need to calculate the average distance of the orbiting chunk of ice from the planet's center. This can be done by finding the average of the inner and outer radii of the rings:
Average distance = (inner radius + outer radius) / 2
= (73,000 km + 170,000 km) / 2
= 121,500 km
Next, we can use Kepler's third law to find the period. Let T represent the period, and r represent the average distance:
T^2 = k * r^3
Solving for T, we get:
T = sqrt(k * r^3)
Since we are only interested in the magnitude of the period, we can disregard the constant k. Thus, the period is given by:
T = sqrt(r^3)
Substituting the value of r, we get:
T = sqrt(121,500^3)
Calculating this, we find:
T ≈ 333,170.7 years
Therefore, the period of an orbiting chunk of ice in the rings of Saturn is approximately 333,170.7 years.
Learn more about orbiting from the following link:
https://brainly.com/question/28888362
#SPJ11
A man has a 40watts and two 60 watt bulb in a room. how much will it cost him to keep them light for 8 hrs, if the cost of a unit in kWh is 50 kobo
Answer: 64 kobos for 8 hours
Explanation:
To calculate the cost of running the bulbs for 8 hours, we need to first determine the total energy consumed by the bulbs.
Energy consumed by the 40-watt bulb in 8 hours = 40 watts * 8 hours = 320 watt-hours
Energy consumed by one of the 60-watt bulbs in 8 hours = 60 watts * 8 hours = 480 watt-hours
Total energy consumed by the two 60-watt bulbs in 8 hours = 2 * 480 watt-hours = 960 watt-hours
Total energy consumed by all three bulbs in 8 hours = 320 + 960 = 1280 watt-hours = 1.28 kilowatt-hours (kWh)
Now, to calculate the cost of running the bulbs for 8 hours, we need to multiply the total energy consumed (1.28 kWh) by the cost of one unit (50 kobo).
Cost of running the bulbs for 8 hours = 1.28 kWh * 50 kobo/kWh = 64 kobo
Therefore, it will cost him 64 kobos to keep the bulbs lit for 8 hours
Answer the option please do all its just mcqs.
please!
Select the correct statement(s) regarding optical signals. a. Optical signals are immune from radio frequency interference (RFI) b. Optical signal operate in the THz frequency range, which can support
Optical signals refer to the signals that travel through optical fibers, made of glass or plastic, using light waves as carriers. They are used to transmit information from one place to another. The given options are:a. Optical signals are immune from radio frequency interference (RFI).
b. Optical signals operate in the THz frequency range, which can supportc. Optical signals are not affected by the attenuation of electrical signals due to resistance of conductorsLet us discuss each option one by one:a. Optical signals are immune from radio frequency interference (RFI)The statement is true because the optical signals are carried through the glass fibers or plastic wires and are not affected by the interference of other radio frequencies.b. Optical signals operate in the THz frequency range, which can support
However, they don't operate in the entire THz frequency range.c. Optical signals are not affected by the attenuation of electrical signals due to resistance of conductorsThe statement is true because the electrical signals are carried through the metal wires, and the signal strength decreases due to the resistance of the wire. But, the optical signals are carried through the glass fibers or plastic wires and are not affected by resistance or attenuation. Hence, the correct statements are options A, B, and C.
To know more about radio frequency interference visit :
https://brainly.com/question/17646651
#SPJ11
2) Analyze the circuit below to find its function. R2 V₁0- 1/₂0 + w R₁ R gain R₁ ww R₂ R3 ww ww R3 -OV out
The provided circuit diagram lacks clarity and necessary information, making it difficult to determine its function. More specific details, such as resistor values and connections, are needed for proper analysis.
The given circuit appears to be an operational amplifier (op-amp) circuit with resistors (R1, R2, R3) and input voltages (V₁ and V₀) connected to it. However, the circuit diagram provided is not clear and lacks specific information on the connections and component values. Without a clearer diagram or more information, it is challenging to determine the exact function of the circuit.
Generally, op-amp circuits can perform various functions such as amplification, filtering, summing, integrating, differentiating, etc. The function of the circuit depends on the configuration of the op-amp, the values of resistors, and the connections of input and output terminals. These details are not explicitly provided in the given circuit description.
To determine the circuit's function, a clearer circuit diagram or additional information about the op-amp model, resistor values, and the specific connections between components would be necessary. With more specific information, it would be possible to analyze the circuit and determine its intended purpose or function.
To know more about resistors ,
https://brainly.com/question/30672175
#SPJ11
What is the typical maximum working voltage of a solid electrolyte tantalum capacitor? A. 125 VDC B. 200 VDC C. 150 VDC D. 400 VDC
The typical maximum working voltage of a solid electrolyte tantalum capacitor is 125 VDC. A long answer to this question is provided below:Solid electrolyte tantalum capacitor The solid electrolyte tantalum capacitor is a type of tantalum capacitor that has a solid electrolyte.
This type of capacitor is polarized and is generally used in electronic circuits that require high capacitance and low leakage current. This type of capacitor is also used in circuits that require a low equivalent series resistance and a low equivalent series inductance. It is typically used in power supply circuits, filter circuits, and decoupling circuits.The working voltage of a capacitor The working voltage of a capacitor is the maximum voltage that the capacitor can withstand without breaking down. If the voltage across the capacitor exceeds the working voltage, the capacitor can be permanently damaged.
The working voltage of a capacitor depends on the type of capacitor and the materials used to make it.Typical maximum working voltage of a solid electrolyte tantalum capacitor The typical maximum working voltage of a solid electrolyte tantalum capacitor is 125 VDC. This means that the capacitor can withstand a maximum voltage of 125 volts DC without breaking down. If the voltage across the capacitor exceeds 125 VDC, the capacitor can be permanently damaged. This voltage rating is lower than that of other types of capacitors, such as ceramic capacitors and aluminum electrolytic capacitors. Therefore, solid electrolyte tantalum capacitors should be used in circuits that do not require high voltage ratings.
To know more about capacitor visit:-
https://brainly.com/question/31627158
#SPJ11
Page 6 of 6
Question 16 (1 point)
Consider three emission sources. Source 1: glowing light-bulb filament; Source 2:
glowing light-bulb filament with a chamber of sodium gas in the light's path; Source:
3: low-pressure sodium gas in a discharge tube. Which of the following is correct?
Source 1 gives out a continuous color spectrum that makes up the rainbow but
certain lines are dark
Source 3 gives out a discrete set color lines which include but are not limited to:
the dark lines from Source 2
Source 2 gives out a discrete set of color lines of which the lines of Source 3 are a subset.
Source 2 gives out a continuous color spectrum that makes up the rainbow but
with dark lines that match exactly the lines from Source 3.
Source 2 gives out a discrete set of color lines of which the lines of Source 3 are a subset. So the correct answer is (C)..
We have three sources: Source 1: glowing light-bulb filament; Source 2: glowing light-bulb filament with a chamber of sodium gas in the light's path; Source 3: low-pressure sodium gas in a discharge tube.
We know that source 1, glowing light-bulb filament gives out a continuous color spectrum that makes up the rainbow but certain lines are dark. Hence, option A is incorrect. We know that source 3, low-pressure sodium gas in a discharge tube gives out a discrete set of color lines which include but are not limited to the dark lines from Source 2.
Option B is incorrect. We know that Source 2 gives out a discrete set of color lines of which the lines of Source 3 are a subset. Source 2, a glowing light-bulb filament with a chamber of sodium gas in the light's path gives out a continuous color spectrum that makes up the rainbow but with dark lines that match exactly the lines from Source 3. Option D is incorrect.
To know more about spectrum please refer to:
https://brainly.com/question/31086638
#SPJ11
(i) A single phase half wave converter is supplied by a 120 V, 60 Hz AC source in the primary winding. Transformer has a turns ratio of 1:2 and a resistive load of (68+ 1) k12. Assuming a delay angle of (15 + 68/10) degrees, calculate (a) average and rms values of output voltage and current (b) rectification efficiency (c) form factor (d) ripple factor [6] (ii) Calculate the rectification efficiency, form factor and ripple factor for the above case if the device was a semi converter, and comment on which converter is better in terms of the performance parameters, [4] Hint: Remember that for AC sources, the value given in the ratings is the RMS value of the AC signal, not the peak/maximum value.
The rectification efficiency, form factor, and ripple factor of the half-wave converter are 0.198, 1.79, and 0.000614, respectively, and for the semi-converter are 0.317, 1.11, and 0.
(i) Given:
Primary voltage, V₁ = 120 V
Frequency, f = 60 Hz
Turns ratio, n = 1 : 2
Resistive load, R = (68 + 1) kΩ = 69 kΩ
Delay angle, α = 15 + 68/10 = 21.8° (approx)
Output voltage, V₂ = V₁/n
Output voltage, V₂ = 120/2 = 60 V
The rms value of output voltage, V₂(rms) = V₂/√2
The rms value of output voltage, V₂(rms) = 60/√2
The rms value of output voltage, V₂(rms) = 42.43 V
Output current, I₂ = V₂/R
The average value of output voltage, V₂(avg) = (2/π) Vm (cos α - cos π)
Here, Vm = peak voltage
The peak voltage of transformer secondary, V₂(pk) = V₂
The peak voltage of transformer secondary, V₂(pk) = 60 V
V₂(avg) = (2/π) (60) (cos 21.8 - cos π)
V₂(avg) = 23.69 V
The rms value of output current, I₂(rms) = (V₂(rms))/(R)
I₂(rms) = (42.43)/(69 × 10³)
I₂(rms) = 0.614 mA
Rectification efficiency, η = (DC power output)/(AC power input)
DC power output = V₂(avg) × I₂(avg) = 23.69 × 0.614 × 10⁻³ = 0.0146 W
AC power input = V₁ × I₁
AC power input = 120 × I₁
The rms value of input current, I₁(rms) = I₂(rms)/n
I₁(rms) = 0.614 × 10⁻³/1
I₁(rms) = 0.614 mA
AC power input = 120 × 0.614 × 10⁻³
AC power input = 0.0737 W
Rectification efficiency, η = (DC power output)/(AC power input)
η = 0.0146/0.0737
η = 0.198
Form factor = (rms value of output voltage)/(average value of output voltage)
Form factor = V₂(rms)/V₂(avg)
Form factor = (42.43)/(23.69)
Form factor = 1.79
Ripple factor, r = (rms value of AC component)/(DC component)
Ripple factor, r = (I₂(rms))/(I₂(avg)) - 1
r = (0.614 × 10⁻³)/(0.614 × 10⁻³) - 1
r = 0
(ii) The given circuit is a single-phase half-wave converter and the performance parameters are:
Rectification efficiency, η₁ = 0.198
Form factor, FF₁ = 1.79
Ripple factor, RF₁ = 0.000614
A semi-converter is the one which converts an input AC voltage into an output DC voltage. It is a unidirectional converter, which means the output voltage has the same polarity as the input voltage. The semi-converter circuit is:
It can be seen that the output voltage of the semi-converter is half of the input
voltage.
In a semi-converter, only one half-cycle of the input voltage is used, and the other half-cycle is blocked.
The performance parameters of the semi-converter are:
Output voltage, V₂ = V₁/2
Output voltage, V₂ = 120/2
Output voltage, V₂ = 60 V
The rms value of the output voltage, V₂(rms) = V₂/√2
The rms value of the output voltage, V₂(rms) = 60/√2
The rms value of the output voltage, V₂(rms) = 42.43 V
Output current, I₂ = V₂/R
The average value of the output voltage, V₂(avg) = (2/π) Vm
The peak voltage of the transformer secondary, V₂(pk) = V₂
V₂(avg) = (2/π) (60)
V₂(avg) = 38.19 V
The rms value of the output current, I₂(rms) = (V₂(rms))/(R)
I₂(rms) = (42.43)/(69 × 10³)
I₂(rms) = 0.614 mA
The rms value of the input current, I₁(rms) = I₂(rms)
I₁(rms) = 0.614 mA
Output power, P = V₂(avg) × I₂(avg)
P = 38.19 × 0.614 × 10⁻³
P = 0.0234 W
Rectification efficiency, η = (DC power output)/(AC power input)
DC power output = P
η = DC power output/AC power input
AC power input = V₁ × I₁
AC power input = 120 × 0.614 × 10⁻³
AC power input = 0.0737 W
η = P/AC power input
η = 0.0234/0.0737
η = 0.317
Form factor, FF = (rms value of the output voltage)/(average value of the output voltage)
FF = V₂(rms)/V₂(avg)
FF = (42.43)/(38.19)
FF = 1.11
Ripple factor, r = (rms value of the AC component)/(DC component)
r = (I₂(rms))/(I₂(avg)) - 1
r = (0.614 × 10⁻³)/(0.614 × 10⁻³) - 1
r = 0
To know more about rectification visit:
https://brainly.com/question/30360755
#SPJ11
When a component is used to perform the function of stop in a control circuit, it will generally be a normally ____ component and be connected in ____ with the motor starter coil
Closed series
Change position
Parallel
When a component is used to perform the function of stop in a control circuit, it will generally be a normally closed component and be connected in parallel with the motor starter coil. Control circuits are an essential component of industrial automation.
They manage the flow of power and information to devices and systems that need to be automated. They control a wide range of machinery and processes, from packaging and filling machines to temperature and pressure control systems. Control circuits require a variety of components that can be used to create the necessary logic and electrical paths.
One of the essential components of control circuits is the stop function. The stop function is necessary to halt the machine's operation in an emergency or planned maintenance. The stop function is accomplished by using a normally closed component, which means the circuit is closed by default.
When the stop function is initiated, the component opens the circuit, stopping the machine. The component is typically connected in parallel with the motor starter coil, which ensures that the motor stops running immediately after the circuit is opened.
To know more about component visit :
https://brainly.com/question/30324922
#SPJ11
The ............ represents the............. response of a stable system to a ........ signal at various frequencies.
The frequency response represents the output response of a stable system to a given signal of various frequencies. In general, it is defined as the ratio of the output to the input signal's complex amplitude as a function of frequency.
The frequency response is a measure of how well the system responds to the input signal at various frequencies.
It provides information about the system's gain and phase shift at different frequencies, which are critical in signal processing. When an input signal is applied to a system, it produces an output signal that may be of greater or lower magnitude than the input signal and may have a phase shift relative to the input signal. The magnitude of the frequency response is the ratio of the output signal's amplitude to the input signal's amplitude.
The phase response, on the other hand, is the difference between the output signal's phase and the input signal's phase. Frequency response analysis is important in signal processing, communications, and control systems engineering, among other fields.
To know more about frequencies visit:-
https://brainly.com/question/31938473
#SPJ11
Why didn't Cornelius Drebbel get full credit for inventing the
first air conditioner in 1620?
the lack of extensive documentation, the limited scope and impact of Drebbel's invention compared to modern air conditioning systems, the historical context of invention, and the evolving nature of recognition all contribute to why he may not have received full credit for inventing the first air conditioner in 1620.
Cornelius Drebbel, a Dutch inventor, is often credited with inventing the first air conditioner in 1620. However, he did not receive full credit for this invention for a few reasons:
1. Lack of Documentation: During Drebbel's time, scientific and technological advancements were not documented and published as extensively as they are today. As a result, the details and documentation of Drebbel's air conditioning invention may have been insufficient or lost over time. Without proper documentation, it becomes challenging to establish a comprehensive historical record and give full credit to the inventor.
2. Limited Scope and Impact: While Drebbel's invention was a notable achievement, it is important to consider the scope and impact of his invention compared to modern air conditioning systems. Drebbel's invention was a rudimentary form of air conditioning that involved cooling and circulating air using a combination of ice, water, and bellows. It was not as advanced or widespread in its application as the air conditioning systems developed in the 20th century, which revolutionized comfort cooling in buildings and transportation.
3. Historical Context: Inventions and discoveries often build upon previous knowledge and ideas. Drebbel's work on air conditioning was influenced by the understanding of thermodynamics and heat transfer that had developed over centuries. It is difficult to pinpoint a single individual as the sole inventor of a particular technology when it is part of a broader evolutionary process.
4. Recognition Over Time: The recognition and acknowledgment of inventions can evolve and change over time as new information emerges or historical perspectives shift. It is possible that Drebbel's contribution to air conditioning has gained more recognition and appreciation in recent years as historians and researchers delve deeper into the history of technological advancements.
Overall, the lack of extensive documentation, the limited scope and impact of Drebbel's invention compared to modern air conditioning systems, the historical context of invention, and the evolving nature of recognition all contribute to why he may not have received full credit for inventing the first air conditioner in 1620.
to know more about thermodynamics visit:
brainly.com/question/15591590
#SPJ11
4) A toy car of mass 0.78 g is propelled up a curved track by a compressed spring. Find the final speed of the car if its initial speed is 2.10 m/s and the slope is 0.190 m high, assuming negligible friction.
Previous question
The final speed of the toy car, assuming negligible friction, is approximately 2.05 m/s.
To find the final speed of the toy car, we can use the principle of conservation of mechanical energy, assuming negligible friction. The initial kinetic energy of the car will be converted into potential energy as it moves up the curved track, and then back into kinetic energy at the highest point of the track.
The total mechanical energy at any point on the track can be calculated as:
E = KE + PE
where E is the total mechanical energy, KE is the kinetic energy, and PE is the potential energy.
Initially, the car has an initial speed (v₀) and no potential energy:
E₁ = KE₁ + PE₁
E₁ = (1/2) * m * v₀² + 0
E₁ = (1/2) * 0.78 g * (2.10 m/s)²
Next, at the highest point of the track, all the initial kinetic energy will be converted into potential energy:
E₂ = KE₂ + PE₂
E₂ = 0 + m x g x h
E₂ = 0.78 g x 9.8 x 0.190 m
Since mechanical energy is conserved, E₁ = E₂:
(1/2) x 0.78 g x (2.10 )² = 0.78 g x 9.8 x 0.190 m
Now we can solve for the final speed (vf). Rearranging the equation:
[tex]v_f = \sqrt{\dfrac{(2 \times E_2)} { m}[/tex]
Substituting the given values:
[tex]v_f = \sqrt{\dfrac{(2 \times 0.78 \times 9.8 \times 0.190 m)} { (0.78 g}}[/tex]
Simplifying:
[tex]v_f = \sqrt {(2 \times 9.8 \times 0.190 )}[/tex]
Calculating the final speed:
[tex]v_f = 2.05\ \dfrac{m}{s}[/tex]
Therefore, the final speed of the toy car, assuming negligible friction, is approximately 2.05 m/s.
To know more about speed follow
https://brainly.com/question/31284357
#SPJ4
In a plane radio wave the maximum value of the electric field
component is 6.18 V/m. Calculate (a) the maximum
value of the magnetic field component and (b) the
wave intensity.
The maximum value of the magnetic field component is 2.06 × 10^−8 T and the wave intensity is 2.22 × 10^−5 W/m2.
(a)The maximum value of the magnetic field component is given by the following formula:
Bmax= Emax/c Where Bmax is the maximum value of the magnetic field component, Emax is the maximum value of the electric field component, and c is the speed of light in vacuum.
Therefore,
Bmax= Emax/c
= 6.18/3 × 10^8
= 2.06 × 10^−8 T
(b)The wave intensity is given by the following formula:
I= Emax^2/2μ0
where I is the wave intensity, Emax is the maximum value of the electric field component, and μ0 is the permeability of free space. Therefore,
I= Emax^2/2μ0
(6.18)^2/2 × π × 10^−7
= 2.22 × 10^−5 W/m2
To know more about wave intensity visit:-
https://brainly.com/question/32981757
#SPJ11
The full-load slip of a 2-pole induction motor at 50 Hz is 0.04.
Estimate the speed at which the motor will develop rated torque if
the frequency is reduced to (a) 25 Hz, (b) 3 Hz. Assume that in
both cases the voltage is adjusted to maintain full air-gap Xux.
Calculate the corresponding slip in both cases, and explain why the
very low-speed condition is ineYcient. Explain using the equivalent
circuit why the full-load currents would be the same in all the three
cases.
when the frequency is reduced to 25 Hz or 3 Hz, the motor will develop rated torque at a speed of 2880 RPM with a slip of 4% in both cases. Very low speeds are inefficient due to increased slip and higher power losses. The equivalent circuit parameters, including impedances, remain unchanged as the rated current is constant.
The synchronous speed of an induction motor is given by the formula:
Ns = (120 * f) / P
where Ns is the synchronous speed in RPM, f is the frequency in Hz, and P is the number of poles.
Given that the motor is a 2-pole motor and the frequency is 50 Hz, we can calculate the synchronous speed at full-load slip:
Ns = (120 * 50) / 2 = 3000 RPM
The speed at which the motor will develop rated torque can be calculated by subtracting the slip speed from the synchronous speed:
N = Ns - (Slip * Ns)
where N is the speed at which the motor will develop rated torque.
a) When the frequency is reduced to 25 Hz:
N = 3000 RPM - (0.04 * 3000 RPM) = 2880 RPM
b) When the frequency is reduced to 3 Hz:
N = 3000 RPM - (0.04 * 3000 RPM) = 2880 RPM
In both cases, the speed at which the motor will develop rated torque is 2880 RPM.
The slip can be calculated using the formula:
Slip = (Ns - N) / Ns
a) For 25 Hz:
Slip = (3000 RPM - 2880 RPM) / 3000 RPM = 0.04 or 4%
b) For 3 Hz:
Slip = (3000 RPM - 2880 RPM) / 3000 RPM = 0.04 or 4%
The very low-speed condition is inefficient because the slip becomes a larger proportion of the synchronous speed. As the frequency decreases, the slip increases, resulting in a higher percentage of energy being dissipated as heat in the rotor and increased power losses. At very low speeds, the motor's efficiency decreases significantly due to increased copper and iron losses.
In the equivalent circuit of an induction motor, the stator impedance and rotor impedance are dependent on the rated current. Since the rated current remains the same in all three cases, the impedances and hence the circuit parameters remain unchanged. Therefore, the full-load currents would be the same in all the three cases.
To learn more about torque, click here: https://brainly.com/question/30338175
#SPJ11
An external force F moves a 4.50−kg box at a constant speed v up a frictionless ramp, as shown in the figure. The force acts in a direction parallel to the ramp. Calculate the work W done on the box by this force as it is pushed up the 5.00−m ramp to a height h=4.00 m. W= How does the work done on the box compare to the change in gravitational potential energy ΔUgrav that the box undergoes as it rises to its final height? W>ΔUgrav W=ΔUgrav W<ΔUgrav
The work done on the box is 220.5 Joules and the work done on the box is greater than the change in gravitational potential energy.
The work done on the box by the external force can be calculated using the formula,
W = Fd,
where
F is the magnitude of the force
d is the displacement.
In this case, the force is acting parallel to the ramp, so we can calculate the work done as the product of the force and the distance along the ramp.
Mass of the box (m) = 4.50 kg
Length of the ramp (d) = 5.00 m
Height (h) = 4.00 m
To calculate the work done, we need to determine the force acting on the box. Since the box is moving at a constant speed, the net force acting on it is zero. This means that the force exerted by the external force is equal in magnitude and opposite in direction to the gravitational force.
The gravitational force acting on the box can be calculated using the formula
F = mg,
where
m is the mass of the box
g is the acceleration due to gravity (approximately 9.8 m/s²).
F = (4.50 kg)(9.8 m/s²) = 44.1 N
Now, we can calculate the work done on the box:
W = Fd = (44.1 N)(5.00 m) = 220.5 J
So, the work done on the box is 220.5 Joules.
To compare the work done to the change in gravitational potential energy, we need to calculate the change in gravitational potential energy.
The change in gravitational potential energy can be calculated using the formula
ΔUgrav = mgh,
where
m is the mass of the box,
g is the acceleration due to gravity,
h is the change in height.
ΔUgrav = (4.50 kg)(9.8 m/s²)(4.00 m) = 176.4 J
Comparing the work done (220.5 J) to the change in gravitational potential energy (176.4 J), we can see that
W > ΔUgrav
This means that the work done on the box is greater than the change in gravitational potential energy.
learn more about gravitational potential energy
https://brainly.com/question/15896499
#SPJ11
Your manager asked you to do a research about complex waveforms, he asked you to do the following: A) Define complex waveform and how it can be generated. B) What is the difference between a simple sinusoidal waveform and the complex one? C) Based on the definition decide whether the following waves are complex waveforms or not: 1) v₁ (t) = 10 sin (wt) 2) y(t)= 10sin(wt)-8sin(7wt) 3) v₂ (t) = 15 sin(wt +) 4) Sawtooth Wave and their relationship
waves 2 and 4 are complex waveforms, while waves 1 and 3 are simple sinusoidal waveforms.
A) A complex waveform refers to a waveform that is composed of multiple sinusoidal components with different frequencies, amplitudes, and phases. It is generated by combining or adding together multiple simple sinusoidal waveforms.
To generate a complex waveform, you can use techniques such as Fourier analysis or superposition. Fourier analysis allows you to decompose a complex waveform into its constituent sinusoidal components, while superposition involves adding together multiple simple waveforms with different frequencies and amplitudes to create a complex waveform.
B) The main difference between a simple sinusoidal waveform and a complex waveform is that a simple sinusoidal waveform consists of a single frequency component and has a regular, repetitive pattern. It can be represented by a single sine or cosine function. On the other hand, a complex waveform consists of multiple frequency components and has a more intricate pattern. It requires the combination of multiple sinusoidal functions to accurately represent its shape.
C) Let's analyze the given waves to determine whether they are complex waveforms:
1) v₁(t) = 10 sin(wt)
This is a simple sinusoidal waveform because it contains only one frequency component (w) and can be represented by a single sine function.
2) y(t) = 10 sin(wt) - 8 sin(7wt)
This is a complex waveform because it contains multiple frequency components (w and 7w) with different amplitudes and can't be represented by a single sine function.
3) v₂(t) = 15 sin(wt + φ)
This is a simple sinusoidal waveform because it contains only one frequency component (w) and can be represented by a single sine function. The phase shift φ does not make it a complex waveform.
4) Sawtooth Wave
A sawtooth wave is a complex waveform because it contains multiple frequency components that create a linearly increasing or decreasing pattern. It cannot be represented by a single sine or cosine function.
In summary, waves 2 and 4 are complex waveforms, while waves 1 and 3 are simple sinusoidal waveforms.
to know more about frequencies visit:
brainly.com/question/30783512
#SPJ11
A spring is extended 15 cm from its equilibrium point. If the spring constant k is 75 N/m, the magnitude and direction of the elastic force Fel are described by which of the following?
A.1.1 × 10^1 N; oriented away from the equilibrium point
B.1.1 × 10^1 N; oriented toward the equilibrium point
C.1.1 × 10^3 N; oriented away from the equilibrium point
D.1.1 × 10^3 N; oriented toward the equilibrium point
The answer is B.1.1 × 10^1 N; oriented toward the equilibrium point.
The magnitude and direction of the elastic force Fel, if a spring is extended 15 cm from its equilibrium point and the spring constant k is 75 N/m can be calculated as follows;
Spring constant, k = 75 N/m
Displacement, x = 15 cm = 0.15 m
The magnitude of the elastic force Fel is given by;
F_el = kx
Where; F_el = elastic force
k = spring constant
x = displacement
Substituting the values of k and x in the above equation we get;
F_el = kx
F_el = 75 N/m × 0.15 m
F_el = 11.25 N
This is the magnitude of the elastic force.
The direction of the elastic force is always in the opposite direction to the displacement from the equilibrium point. Since the displacement is towards the right, the elastic force will be in the left direction,
To learn more on elastic force:
https://brainly.com/question/31468675
#SPJ11
water is flowing at the rate of 6 m^3/min from a reservoir shaped like a______.
Water is flowing at the rate of 6 m^3/min from a reservoir shaped like a cylinder.A cylinder-shaped reservoir is a type of water storage structure. It is circular in shape and has a length of L and a radius of r.
The formula for calculating the volume of a cylinder is given as;V=πr²LFor a cylinder-shaped reservoir, water is flowing at the rate of 6 m^3/min. That means, the volume of water leaving the reservoir per minute is 6m³.A cylinder is a geometric shape with a volume that can be calculated using its radius and height.
Water is flowing from a cylinder-shaped reservoir at a rate of 6 m³/min. If the radius of the cylinder is r and the length is L, the formula for calculating the volume of the cylinder is V = πr²L. If the water is flowing out of the reservoir at a rate of 6 m³/min, then the volume of water leaving the reservoir per minute is also 6 m³.
To know more about structure visit:
https://brainly.com/question/33100618
#SPJ11
The nucleus of a hydrogen atom is a single proton, which has a radius of about 1.1 × 10-15 m. The single electron in a hydrogen atom orbits the nucleus at a distance of 5.3 x 10-¹1 m. What is the ratio of the density of the hydrogen nucleus to the density of the complete hydrogen atom? Number i 1.12E+13 Units (no units)
The ratio of the density of the hydrogen nucleus to the density of the complete hydrogen atom is 1.12 x 10^13.
To find the ratio of the densities, we need to compare the masses and volumes of the hydrogen nucleus and the complete hydrogen atom. The nucleus of a hydrogen atom is a single proton, while the complete hydrogen atom consists of a proton and an electron.
The density of an object is defined as its mass divided by its volume. Since we are comparing the densities, we can calculate the ratio of their masses divided by the ratio of their volumes.
The mass of the hydrogen nucleus is equal to the mass of a proton, which is approximately 1.67 x 10^-27 kg. The mass of the complete hydrogen atom is slightly greater because it includes the mass of the electron, which is much smaller compared to the proton.
The volume of the hydrogen nucleus can be approximated as the volume of a sphere with a radius of 1.1 x 10^-15 m. Similarly, the volume of the complete hydrogen atom can be approximated as the volume of a sphere with a radius of 5.3 x 10^-11 m.
By calculating the ratio of the masses and the ratio of the volumes and then dividing the two ratios, we can determine the ratio of the density of the hydrogen nucleus to the density of the complete hydrogen atom, which is 1.12 x 10^13.
Learn more about Hydrogen atom from the given link:
https://brainly.com/question/30886690
#SPJ11
Question 5 (1 point) If your reaction times follow normal (or Gauss ) distribution, then in the interval (Xav: 0, Xavt o), where Xay is the average reaction time and o is the standard deviation you will find 95% of results 50% of results 33.3% of results 100% of resukts 68% of results
If your reaction times follow a normal distribution, then in the interval (Xav: 0, Xavt o), where Xay is the average reaction time and o is the standard deviation you will find 68% of the results.
A normal distribution is a probability distribution that is symmetrical and bell-shaped. A typical characteristic of the normal distribution is that the mean, median, and mode are equal. Also, the range of the normal distribution extends from negative infinity to positive infinity, implying that the distribution's tails can be long and spread out. For a standard normal distribution with a mean of zero and a standard deviation of one, the interval (Xav: 0, Xavt o) consists of 68% of the observations.
Here's how to calculate it:
Z-score = (X - μ) / σ, where X is the value of interest, μ is the mean, and σ is the standard deviation. Since Z-scores are the same, we can compute the probabilities. To calculate the area between -1 and 1, we'll use a standard normal distribution table. We'll start by locating -1 in the left column and 0.0 in the top row:
This table indicates that the area between -1 and 0.0 is 0.3413. Since the distribution is symmetric, the area between 0.0 and 1 is also 0.3413. As a result, the area between -1 and 1 is the sum of these two values, which is 0.6826. Therefore, in the interval (Xav: 0, Xavt o), where Xay is the average reaction time and o is the standard deviation, you will find 68% of the results.
To learn more about standard deviation:
https://brainly.com/question/14111318
#SPJ11
A quantity of gas at 4 bar and 40 °C occupies a volume of 0.025 m³ in a cylinder behind a piston undergoes a reversible process until the pressure increases to 12 bar while the piston is locked in its initial position. Calculate the heat transfer in kJ. The specific heat capacity at constant pressure, cp is 0.92 kJ/kg K and the specific gas constant, R is 0.260 kJ/kg K.
We need to calculate the temperatures and substitute the values into the equation to find the heat transfer in kJ.
To calculate the heat transfer during the reversible process, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat transfer into the system minus the work done by the system.
The equation for the first law of thermodynamics is:
ΔU = Q - W
Where:
ΔU = Change in internal energy
Q = Heat transfer into the system
W = Work done by the system
In this case, the piston is locked in its initial position, so no work is done (W = 0). Therefore, the equation simplifies to:
ΔU = Q
To calculate the change in internal energy, we can use the ideal gas law:
PV = mRT
Where:
P = Pressure
V = Volume
m = Mass of the gas
R = Specific gas constant
T = Temperature
Since the mass of the gas is not given, we can assume it to be 1 kg without loss of generality. Rearranging the ideal gas law equation to solve for temperature (T):
T = PV / (mR)
For the initial state:
P1 = 4 bar = 400 kPa
V1 = 0.025 m³
T1 = 40 °C = 40 + 273.15 K
For the final state:
P2 = 12 bar = 1200 kPa
Using the ideal gas law, we can find the initial and final temperatures:
T1 = (P1 * V1) / (m * R)
T2 = (P2 * V1) / (m * R)
Since the piston is locked, the volume remains constant (V2 = V1). Therefore, the change in internal energy becomes:
ΔU = cp * m * (T2 - T1)
Given:
cp = 0.92 kJ/kg K
R = 0.260 kJ/kg K
Using the known specific heat capacity and specific gas constant, we can calculate the heat transfer:
Q = cp * m * (T2 - T1)
Now, we need to calculate the temperatures and substitute the values into the equation to find the heat transfer in kJ.
For more such questions on heat transfer , click on:
https://brainly.com/question/16055406
#SPJ8
Plot the two-sided amplitude spectrum of a single-tone modulated FM wave, by hand AND in MATLAB using a stem plot, when the modulation index is
a) Beta = 2
b) Beta = 5
c) Beta = 10
Let the frequency of the modulating signal be 10 kHz, the amplitude of the carrier be 1 V, and the frequency of the carrier be 200 kHz. Make sure to use the Bessel functions when finding the harmonics
In frequency modulation (FM), the message signal modulates the frequency of the carrier wave. In other words, the frequency of the carrier wave varies in accordance with the message signal.
In this way, the amplitude of the FM wave is constant, but its frequency changes according to the message signal's amplitude. We must first use Bessel's function to find the harmonics of the single-tone modulated FM wave before plotting the two-sided amplitude spectrum of the single-tone modulated FM wave by hand or in MATLAB using a stem plot.
Bessel functionJn(k) is used to find the amplitude of the nth harmonic component of a modulated FM wave. As a result, the amplitude of the nth harmonic component can be expressed as:An = [2Jn(β)]/(nπ)Where,An is the amplitude of the nth harmonic component of a modulated FM wave.β is the modulation indexn is the integer order of the nth harmonic component of a modulated FM wave.
By using these harmonic amplitude values, we can plot the two-sided amplitude spectrum of a single-tone modulated FM wave by hand or in MATLAB using a stem plot.
To know more about signal visit:
https://brainly.com/question/31473452
#SPJ11
The single-tone modulated FM wave is given as:c(t) = Ac cos(2πfc t + β sin 2πfm t)Given, the frequency of the modulating signal is 10 kHz, the amplitude of the carrier is 1 V, and the frequency of the carrier is 200 kHz.
We are to plot the two-sided amplitude spectrum of the FM wave by hand and using MATLAB using a stem plot, when the modulation index is β = 2, 5, and 10. We will make use of Bessel functions to determine the harmonics.By inspection, the modulating frequency fm is 10 kHz and the carrier frequency fc is 200 kHz.
Hence, the frequency deviation is given by Δf = βfm. Thus, the frequency deviation is:Δf = βfm = 2 × 10 × 10^3 Hz = 20 × 10^3 HzFor β = 2, 5, and 10, we have the following frequency deviation:β 2 5 10 Δf 20 × 10^3 Hz 50 × 10^3 Hz 100 × 10^3 Hz
The maximum frequency present in the FM signal is given by:fmax = fc + Δf = fc + βfmFor β = 2, 5, and 10, we have the following maximum frequency:fmax 420 kHz 350 kHz 300 kHz
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
Which Thermometer can measure the oral temperature of a child within 25 seconds?
A. Glass thermometer
B. Temporal artery thermometer
C. Tympanic membrane thermometer
D. Electronic thermometer with blue-tipped probe
Thermometer can measure the oral temperature of a child within 25 seconds: C. Tympanic membrane thermometer
The thermometer that can measure the oral temperature of a child within 25 seconds is the tympanic membrane thermometer. This type of thermometer is designed to measure the body temperature by detecting infrared radiation emitted by the tympanic membrane (eardrum).
Tympanic membrane thermometers, also known as ear thermometers, are known for their quick and accurate readings. They have a probe that is gently inserted into the ear canal, and within seconds, the thermometer captures the infrared radiation emitted by the tympanic membrane to determine the body temperature.
Compared to other types of thermometers, such as glass thermometers or electronic thermometers with blue-tipped probes, the tympanic membrane thermometer provides a faster measurement time, making it suitable for measuring the oral temperature of a child who may not stay still for a long period.
It is important to follow the manufacturer's instructions and guidelines for proper usage and accurate readings when using a tympanic membrane thermometer or any other type of thermometer.
Learn more about Thermometer from the given link:
https://brainly.com/question/2339046
#SPJ11
1311 is an isotope of iodine used for the treatment of hyperthyroidism, as it is readily absorbed into the cells of the thyroid gland. With a half-life of 8 days, it decays into 131 xe*, an excited xenon atom. What percentage of an iodine 1311 sample decays after 24 days? In (2) 2= OA. 6.25% Decayed ti B. 12.5 % = In (2) = 0.0866 = 100-12-S = 87.5% 8 ✔C. 87.5% N = No -2 t OD. 93.8 % = e = 12.5 Remain" undecayed? élt
The correct answer is 12.5%, of an iodine 1311 sample decays after 24 days.
The percentage of an iodine 1311 sample that decays after 24 days is 93.8%.
Given that 1311 is an isotope of iodine used for the treatment of hyperthyroidism, as it is readily absorbed into the cells of the thyroid gland. With a half-life of 8 days, it decays into 131 xe*, an excited xenon atom.
Half-life of iodine-1311 (t₁/₂) = 8 days
Amount of iodine-1311 after n half-lives (n) = t / t₁/₂ = 24 / 8 = 3'
From the above equation, it can be understood that 1311 iodine is divided into 8 parts at every 8 days (half-life). So the iodine remaining after 24 days is 1/2³ or 1/8th of its original amount.
Amount of 1311 iodine remaining after 24 days = (1/2)³ = 1/8th of its original amount
Thus, 7/8 or 87.5% of the sample remains undecayed.
The amount of iodine decayed = 1 - 7/8 = 1/8th
The percentage of iodine decayed = (1/8) * 100 = 12.5%
The percentage of an iodine 1311 sample that decays after 24 days is 12.5%.
Hence, the correct answer is 12.5%.
To know more about excited xenon atom, visit:
https://brainly.com/question/7710503
#SPJ11
QUESTION 3
What is the ideal inductance of the coil pictured on the left in problem
1 when the number of turns is 29, the radius of the coil is 27 mm,
the wire gauge is 22 (diameter=0.643 mm),
the length of the coil is 5 cm and the core is made of
iron (μ-1200 x 4 x 10-7 Henries/meter).
Express your answer in millihenries.
The ideal inductance of the coil pictured on the left is L (in millihenries) = L * 1000.
To calculate the ideal inductance of the coil, we can use the formula:
L = (μ₀ * N² * A) / l
Where:
L is the inductance
μ₀ is the permeability of free space (4π × 10⁻⁷ H/m)
N is the number of turns
A is the cross-sectional area of the coil
l is the length of the coil
Given:
Number of turns (N) = 29
Radius of the coil (r) = 27 mm = 0.027 m
Wire gauge (diameter) = 0.643 mm = 0.000643 m
Length of the coil (l) = 5 cm = 0.05 m
Permeability of iron (μ) = 1200 × 4 × 10⁻⁷ H/m
First, let's calculate the cross-sectional area (A) of the coil using the wire gauge:
A = π * (radius of wire)²
= π * (0.000643/2)²
Now, let's substitute the given values into the formula to calculate the inductance (L):
L = (μ₀ * N² * A) / l
Finally, let's convert the inductance to millihenries:
L (in millihenries) = L * 1000
Performing the calculations, we can find the ideal inductance of the coil in millihenries.
To learn more about, inductance, click here, https://brainly.com/question/29981117
#SPJ11
Drag each label to the correct location.
Sort the examples based on whether they describe a physical change or a chemical reaction.
Physical Change: Wax melting, grinding wheat, Adding copper to gold.
Chemical Reaction: Making caramel, tarnishing of silver.
Both Physical Change and Chemical Reaction: Growth of seed into seedling.
Physical Change:
1. Wax melting from applied heat: This is a physical change because the wax undergoes a change in state from solid to liquid due to the application of heat, but its chemical composition remains unchanged.
2. Grinding wheat to make flour: This is a physical change because grinding the wheat grains breaks them down into smaller particles, but there is no chemical reaction involved. The composition of the wheat remains the same.
6. Adding copper to gold to make jewelry: If the copper and gold alloys are simply mixed together without any chemical bonding or reaction, it would be a physical change.
Chemical Reaction:
3. Making caramel by burning sugar: This is a chemical reaction because the sugar undergoes a process called caramelization when it is heated. The heat causes the sugar molecules to break down and form new compounds, resulting in the characteristic browning and flavor of caramel.
4. Tarnishing of silver: This is a chemical reaction because the silver reacts with sulfur or other substances in the environment to form a dark layer called silver sulfide. The composition of the silver changes during tarnishing.
Both Physical Change and Chemical Reaction:
5. Growth of seed into seedling: This involves both physical changes and chemical reactions. The seed absorbs water, undergoes metabolic processes, and converts stored nutrients into new compounds as it grows, which are chemical reactions. At the same time, there are physical changes in the size, shape, and structure of the seed as it develops into a seedling.
For more such information on: Physical Change
https://brainly.com/question/960225
#SPJ8
The Watt steam engine improved on earlier designs in what main way
a. lighter weight
b. all of the above
c. a switch from coal to natural gas as fuel source
d. increased efficiency
Which of the following is an accurate definition of "work" regarding an energy system?
a. energy input to drive the system
b. energy output from the system for its intended purpose
c. energy input required to produce a desired efficiency
d. energy lost within the system as heat
The main way that the Watt steam engine improved on earlier designs was by increasing its efficiency. The Watt steam engine was able to convert more of the heat energy from the steam into mechanical energy, which made it more powerful and efficient.
The accurate definition of "work" regarding an energy system is energy output from the system for its intended purpose. Work is the energy that is actually used to do something, such as lifting a weight or turning a wheel.
The Watt steam engine improved on earlier designs by increasing its efficiency.
Work is the energy that is actually used to do something, such as lifting a weight or turning a wheel.
The Watt steam engine was a significant improvement over earlier steam engines because it was more efficient. The Watt steam engine used a separate condenser, which allowed the steam to be condensed back into water and reused. This increased the efficiency of the steam engine by up to 50%.
The definition of "work" regarding an energy system is the energy output from the system for its intended purpose. This means that the work is the energy that is actually used to do something, such as lifting a weight or turning a wheel.
The energy input to drive the system is not considered work, as it is not used to do anything. The energy lost within the system as heat is also not considered work, as it is not used to do anything.
To learn more about Watt steam engine click here: brainly.com/question/30284781
#SPJ11
/66 The coefficient of static friction for both wedge surfaces is \( 0.40 \) and that between the 27-kg concrete block and the \( 20^{\circ} \) incline is \( 0.70 \). Determine the minimum value of th
The minimum value of the horizontal force P necessary to start the motion of the block is 1115.1 N.
A 27-kg concrete block rests on a wedge having a 20° incline, as shown below. Knowing that the coefficient of static friction for both wedge surfaces is 0.40 and that between the block and incline is 0.70, determine the minimum value of the horizontal force P necessary to start the motion of the block. So, let's solve the problem:
The inclined plane is tilted at an angle of 20°.
The coefficient of static friction between the block and the inclined plane is 0.70.The coefficient of static friction between the inclined plane and the wedge is 0.40.
The minimum value of the horizontal force P necessary to start the motion of the block will be the maximum force of friction. The maximum force of friction can be calculated as follows:
1. Find the normal force acting on the block N = m * g cos θ N
= 27 * 9.81 * cos(20) N = 637.2 N2.
Find the force of friction acting on the block f = µ * N f = 0.70 * 637.2 f = 446.04 N3.
Find the horizontal force P P = f / µ P
= 446.04 / 0.40 P
= 1115.1 N
Therefore, the minimum value of the horizontal force P necessary to start the motion of the block is 1115.1 N.
To learn more about motion visit;
brainly.com/question/32659410
#SPJ11
estion 8 ot yet swered Marked out of 00 - Flag question What is the work needed by an external force to bring a point charge q = 1.93 µC that is 588 cm away from a point charge Q = 68 μC to a point 30.7 cm away (in J)?
Therefore, the work required by an external force to bring a point charge q = 1.93 µC that is 588 cm away from a point charge Q = 68 μC to a point 30.7 cm away is -1.44×10^-3 J.
The potential energy of a system of two point charges Q1 and Q2 separated by a distance r is given by:
U=k(Q1*Q2)/r, where k is Coulomb’s constant (9×10^9 N·m^2/C^2), Q1 and Q2 are the charges, and r is the distance between the charges. Now we can calculate the change in potential energy, ΔU, between the two points:
ΔU=Uf - Ui where Uf is the final potential energy and Ui is the initial potential energy. To calculate the work required to move the charge from the initial to the final position, we use the work-energy principle:W=ΔUwhere W is the work done by the external force, ΔU is the change in potential energy,
and we use the negative sign because the force between the charges is attractive, and the work done by the external force must be equal in magnitude and opposite in sign to the change in potential energy.
Now let's calculate the initial and final potential energies:
Ui=k(Q1*Q2)/ri = k(1.93×10^-6 C)(68×10^-6 C)/(588×10^-2 m)
Ui = 1.13×10^-3 J (to three significant figures)
Uf=k(Q1*Q2)/rf = k(1.93×10^-6 C)(68×10^-6 C)/(30.7×10^-2 m)
Uf = 2.57×10^-3 J (to three significant figures)Now let's calculate the work done by the external force:
ΔU=Uf - Ui=2.57×10^-3 J - 1.13×10^-3
JW=-ΔU=-(2.57×10^-3 J - 1.13×10^-3 J)
W = -1.44×10^-3 J (to three significant figures)
Therefore, the work required by an external force to bring a point charge q = 1.93 µC that is 588 cm away from a point charge Q = 68 μC to a point 30.7 cm away is -1.44×10^-3 J.
To know more about potential visit:
https://brainly.com/question/28300184
#SPJ11