The mechanical energy dissipated for the sphere in front is 3.104005 J.
To determine the amount of mechanical energy dissipated for the sphere, we need to analyze the change in mechanical energy over time.
The given data provides the mechanical energy values at different time points (t) for the sphere.
Since dissipative forces, such as air resistance, are present, the mechanical energy of the sphere will gradually decrease over time.
To estimate the amount of energy dissipated, we can consider the change in mechanical energy between the initial and final time points.
From the given data, we can see that the initial mechanical energy is 112.728513 J, and the final mechanical energy is 115.832518 J.
To calculate the mechanical energy dissipated, we can find the difference between these two values:
Mechanical energy dissipated = Final mechanical energy - Initial mechanical energy
= 115.832518 J - 112.728513 J
= 3.104005 J
Therefore, the mechanical energy dissipated for the sphere in front is approximately 3.104005 J.
Learn more about mechanical energy from the given link
https://brainly.com/question/24443465
#SPJ11
??
How many state required for laser distance measurement? (HILSMs) 2
The HILSMs or High-Intensity Laser Safety Measures are a set of safety precautions that are taken while using high-intensity laser technology to avoid any accidents or injuries. It is necessary to follow these safety measures, and there are two states that are required for laser distance measurement.
The following are the two states required for laser distance measurement:Safe DistanceThe safe distance is the distance from the laser source beyond which the level of laser radiation is within a safe limit. It is crucial to maintain the safe distance from the laser source while measuring the distance.
The safe distance varies depending on the laser type, the environment, and other factors, and it is essential to take all of these factors into account while measuring the distance.Eye ProtectionThe use of appropriate eye protection is necessary to avoid any eye damage from the laser radiation. The eye protection used must be appropriate for the laser type and the laser class. It is essential to wear the eye protection throughout the laser measurement process, and it must be worn even if the laser beam is not visible.Laser distance measurement is a useful tool, but it must be done safely, and the two states required for it are the safe distance and eye protection.
To know more about Intensity visit;
https://brainly.com/question/17583145
#SPJ11
Current might flow in two different manners. what are they?
Current can flow in two different manners: Direct Current (DC) with a constant unidirectional flow, and Alternating Current (AC) with a periodically changing direction.
Current can flow in two different manners:
1. Direct Current (DC): In DC, the flow of electric charge is unidirectional and constant over time. The current maintains a steady magnitude and direction.
2. Alternating Current (AC): In AC, the flow of electric charge periodically changes direction. The current continuously oscillates back and forth, reversing its polarity at regular intervals. This is commonly used for power distribution and in many electronic devices.
3. Pulsating Direct Current (PDC): Pulsating Direct Current is a type of current that flows in a unidirectional manner but with a time-varying magnitude. The current level increases and decreases in pulses or bursts, but it always flows in the same direction.
4. Transient Current: Transient Current refers to a temporary and non-continuous flow of electric charge. It occurs during brief periods of time when there are sudden changes or disturbances in a circuit, such as during power-up or power-down events, switching operations, or in response to electrical faults.
To know more about Alternating Current refer here
https://brainly.com/question/31609186#
#SPJ11
Page 4 of 6 II. Answer all questions below (14 marks): 1- What is the resultant force? (1 mark) 4 N 3 N 2- A freely fall object has a speed of 2 m/s at one instant, What will it be its speed 2 s later? (1 mark) 3- Two blocks with different masses move with differenct velocities. The first block (m₁-2 Kg) moves to the left at 4 m/s and the second block (m₂- 3 Kg) moves to the right with a speed of 5 m/s. When they collide, they stick and move together. What is the type of collision? Use the law of conservation of momentum to find the velocity of the blocks after the collision? (3 marks) 4- A 60 kg person walks from the ground to the roof of a 80 m tall building. How much increase in gravitational potential energy is there? (Take g = 10 N/kg). (1 mark)
3 N to the right is the Resultant force. 18 m/s is the speed. 1.4 m/s is the velocity. 4.9 x 10⁴ J is the gravitational potential energy.
An object's push or pull that causes it to accelerate is referred to as force, which is a fundamental notion in physics. Newton's second equation of motion states that force equals mass times acceleration, meaning that the more force is supplied to an item, the faster it will move. The force is measured in newtons and can be divided into a number of different categories, including nuclear, electromagnetic, and gravitational forces.
1.Resultant force = (4 N to the right - 1 N to the left)
=3 N to the right
2.speed =(2 m/s + 9.8 m/s² x 2 s)
=18 m/s
3.Initial momentum = m₁v₁ + m₂v₂
= (2 kg)(-4 m/s) + (3 kg)(5 m/s)
= 7 kg m/s
Final momentum = (m₁ + m₂)v
= (2 kg + 3 kg)v
= 5 kg v
Initial momentum = Final momentum
7 kg m/s = 5 kg v
v = 1.4 m/s
4.gravitational potential energy = (60 kg x 80 m x 10 N/kg)
= 4.9 x 10⁴ J
To know more about force, here:
https://brainly.com/question/30507236
#SPJ4
Problem No. 1 Find the feedback coefficient 3 for sustained oscillation, give that the open-loop gain equals to :- 1. Ao 3+j4 2. Ao 10 exp(-i 2) Problem No.2 . . Prove that FSR (Free Spectral Range) = c/2n. d Find FSR for Gaz Laser of length "30 cm" Find the corresponding Αλ.
Problem 1: Feedback coefficient is θ = -2° the feedback coefficient 3 for sustained oscillation, we must set the product of the open-loop gain (A₀) and the feedback coefficient 3 to -1 ; d) The corresponding wavelength is 600 nm or 0.6 μm.
Problem No.1 To determine the feedback coefficient 3 for sustained oscillation, we must set the product of the open-loop gain (A₀) and the feedback coefficient 3 to -1. Therefore, we can rewrite the equation for loop gain (LG) as follows: LG = A₀*3 = -1
Dividing both sides of the equation by A₀, we get:3 = (-1) / A₀
We will now compute the values of 3 using the given values of A₀ :If A₀ = 3+j4, then A₀ = √(3²+4²) = 5 and the angle θ of A₀ = arctan (4/3) = 53.13°. Thus: 3 = (-1) / 5
= -0.2 and θ = 53.13°
If A₀ = 10 exp(-i2), then A₀ = 10 and θ = -2°.
Thus: 3 = (-1) / 10 = -0.1
and θ = -2°
d) To prove that FSR = c/2nd, let us assume that a light wave has a frequency f and that it travels in a laser cavity with mirrors separated by a distance L. Because the wave must be an integer number n of wavelengths λ, its frequency is constrained by the relation: f = n (c/λ)where c is the speed of light. Since the wave travels a round-trip distance of 2L, we have:nλ = 2L
Therefore, the frequency of the wave can be written as: f = n (c/2L)Since the FSR is the frequency spacing between two consecutive resonances, we have: FSR = f(n+1) - fn = c/2L
We can now compute the FSR for a gas laser of length L = 30 cm: FSR = c/2L
= (3*⁸ m/s)/(2*0.3 m)
= 5*10⁸ Hz
To find the corresponding wavelength λ, we use: f = c/λ where f is the frequency of the wave.
Thus:λ = c/f = (3*10⁸m/s)/(5*10⁸ Hz) = 0.6 m or 600 nm
Therefore, the corresponding wavelength is 600 nm or 0.6 μm.
To know more about sustained oscillation, refer
https://brainly.com/question/31197565
#SPJ11
a. Write the expression for energy stored in an inductor.
b. What is the physical reason that damping increases as the resistance in a parallel RLC circuit decreases?
c. What is a phasor?
d. The following voltage-current pair was measured for a passive device. Is it resistive, inductive, or capacitive? V(t) = 15sin(400t + 30degrees) and V i(t) = 3cos(400t + 30degrees)
e. A 10 nF capacitor is connected in series with a 100 nH inductor. They operate at f = 10 MHz. What is the equivalent admittance, Yeq ?
a. The expression for energy stored in an inductor is W = (1/2) * L * I^2, where W represents the energy stored, L is the inductance of the inductor, and I is the current flowing through the inductor.
b. The physical reason that damping increases as the resistance in a parallel RLC circuit decreases is that lower resistance allows for increased energy dissipation in the circuit. Resistance converts electrical energy into heat, reducing the oscillations in the circuit. Therefore, as resistance decreases, more energy is dissipated as heat, leading to higher damping and decreased oscillations.
c. A phasor is a complex number representation used to simplify the analysis of sinusoidal waveforms in electrical circuits. It represents the amplitude and phase of a sinusoidal quantity. Phasors are often used to represent voltages and currents in AC circuits, allowing for algebraic calculations instead of complex trigonometric functions. By using phasors, the analysis of circuits with sinusoidal signals becomes more manageable and can be solved using basic algebraic operations.
d. Based on the given voltage-current pair, V(t) = 15sin(400t + 30 degrees) and i(t) = 3cos(400t + 30 degrees), we can observe that both the voltage and current have the same frequency and are out of phase by 30 degrees. This indicates that the circuit is capacitive. In a capacitive circuit, the current leads the voltage by 90 degrees, so the presence of a cosine term in the current expression confirms its capacitive nature.
e. To find the equivalent admittance (Yeq), we need to calculate the admittance of each component individually and then combine them using the appropriate formulas. The admittance of a capacitor (Yc) can be calculated as Yc = jωC, where j is the imaginary unit, ω is the angular frequency (2πf), and C is the capacitance. The admittance of an inductor (Yl) can be calculated as Yl = 1 / (jωL), where L is the inductance. Once we have Yc and Yl, we can add them as complex numbers to obtain Yeq.
To learn more about, Inductor, click here, https://brainly.com/question/31503384
#SPJ11
a slowly moving ship has a large momentum because of its
A slowly moving ship has a large momentum because of its mass.
Momentum is a property of moving objects and is defined as the product of an object's mass and its velocity. In the case of a slowly moving ship, it can still have a large momentum because of its mass.
The momentum of an object is directly proportional to its mass and velocity. This means that if the mass of an object is large, its momentum will also be large, even if its velocity is relatively low.
A ship is a massive object, and even if it is moving slowly, its mass contributes to a significant momentum. The mass of a ship is much larger compared to smaller objects like cars or bicycles, which means that even at low speeds, the ship can have a substantial momentum.
Learn more:About slowly moving ship here:
https://brainly.com/question/2878346
#SPJ11
What would be the effect of replacing a 640 nm photosensor with a 890 nm IR sensor on the same system. Both are being used to detect surface color differences. What would be the effect on output voltage? Explain any other relevant impacts.
The effect on output voltage the photosensor and IR sensor have different wavelengths of sensitivity.
Replacing a 640 nm photosensor with an 890 nm IR sensor would have several effects on the system, particularly on the output voltage and the detection of surface color differences.
Effect on output voltage: The photosensor and IR sensor have different wavelengths of sensitivity.
The photosensor is optimized for detecting light in the visible spectrum around 640 nm, while the IR sensor is designed for detecting light in the infrared range around 890 nm.
As a result, the output voltage of the IR sensor would be significantly lower compared to the photosensor when detecting surface color differences.
This is because the IR sensor would have reduced sensitivity to the visible light wavelengths.
Impact on color detection: The replacement of the photosensor with an IR sensor would likely result in reduced accuracy or inability to detect surface color differences effectively.
Since the IR sensor is primarily sensitive to infrared light, it may not be able to distinguish between different colors in the visible spectrum. Colors that were easily distinguishable by the photosensor may appear similar or indistinguishable to the IR sensor.
This can lead to inaccurate or unreliable color detection.
Other relevant impacts: The IR sensor may also be influenced by ambient infrared light sources present in the environment, which could introduce additional noise or interference into the system.
Moreover, if the system was designed to interpret specific colors based on the output voltage of the photosensor, the change to an IR sensor would require reprogramming or recalibrating the system to account for the different sensitivity and response characteristics of the IR sensor.
In summary, replacing a 640 nm photosensor with an 890 nm IR sensor would likely result in a lower output voltage, reduced accuracy in detecting surface color differences, and the need for adjustments to accommodate the different sensor characteristics.
For more questions on voltage
https://brainly.com/question/3631756
#SPJ8
An aluminum rectangular waveguide with dimensions a=4.2cm and b=1.5cm filled with Teflon (&r=2.6) operates at 3GHz. a. Determine the range of frequencies for which the guide will operate single mode TE10 b. Calculate the impedance at dominant mode
The impedance at the dominant mode (TE10) of the rectangular waveguide is approximately 192.4 ohms.
The range of frequencies for which the aluminum rectangular waveguide will operate in the single mode TE10, we need to consider the cutoff frequency for the TE10 mode.
a. Cutoff Frequency for TE10 Mode:
The cutoff frequency (fc) for the TE10 mode can be calculated using the formula:
fc = c / (2 * √(εr - 1) * a)
Where:
c is the speed of light in vacuum (3 x 10^8 m/s)
εr is the relative permittivity of Teflon (2.6)
a is the width of the waveguide (4.2 cm = 0.042 m)
Substituting the given values into the formula, we can calculate the cutoff frequency:
fc = (3 x 10^8 m/s) / (2 * √(2.6 - 1) * 0.042 m)
fc ≈ 5.56 GHz
Therefore, the waveguide will operate in the single mode TE10 for frequencies below the cutoff frequency of 5.56 GHz.
b. Impedance at Dominant Mode (TE10):
The characteristic impedance (Z0) at the dominant TE10 mode of the rectangular waveguide can be calculated using the formula:
Z0 ≈ 60 / √(εr - 1) * (b / a)
Where:
εr is the relative permittivity of Teflon (2.6)
a is the width of the waveguide (4.2 cm = 0.042 m)
b is the height of the waveguide (1.5 cm = 0.015 m)
Substituting the given values into the formula, we can calculate the impedance:
Z0 ≈ 60 / √(2.6 - 1) * (0.015 m / 0.042 m)
Z0 ≈ 192.4 ohms
To know more about impedance refer here
https://brainly.com/question/12433840#
#SPJ11
There are 2 particle energies. The degeneracies of them are both 4.If there are 4 fermions in the system. What are the possible distributions of the system? What are the number of accessible states of the distributions?
There are 131 accessible states of the distributions.
There are two particle energies with degeneracies of both = 4. And the number of fermions = 4 To find:
The possible distributions of the system and the number of accessible states of the distributions.
The number of particles with energy e1 can be 0, 1, 2, 3, or 4.
The number of particles with energy e2 can be 0, 1, 2, 3, or 4.
The total number of states = (5 + 4 + 3 + 2 + 1) x (5 + 4 + 3 + 2 + 1) = (15)² = 225 states.
This is because each of the two energy levels has a degeneracy of 4 and there are 4 fermions in total.
Arrangement for e1=0Particle 0 1 2 3 4Total states 1 4 10 20 35
Arrangement for e2=0Particle 0 1 2 3 4Total states 1 4 10 20 35
Arrangement for e1=1Particle 0 1 2 3 4Total states 0 4 8 12 16
Arrangement for e2=1Particle 0 1 2 3 4Total states 0 4 8 12 16
Arrangement for e1=2Particle 0 1 2 3 4Total states 0 0 4 6 6
Arrangement for e2=2Particle 0 1 2 3 4Total states 0 0 4 6 6
Arrangement for e1=3Particle 0 1 2 3 4Total states 0 0 0 1 3
Arrangement for e2=3Particle 0 1 2 3 4Total states 0 0 0 1 3
Arrangement for e1=4Particle 0 1 2 3 4Total states 0 0 0 0 1
Arrangement for e2=4Particle 0 1 2 3 4Total states 0 0 0 0 1
Total accessible states = 1 + 4 + 10 + 20 + 35 + 4 + 8 + 12 + 16 + 4 + 6 + 6 + 1 + 3 + 1 = 131 states.
To know more about accessible states please refer to:
https://brainly.com/question/30011658
#SPJ11
what would you say are the main contributors to energy and emissions? What are the typical 3-4 major energy end uses in a home? How do you think that differs between Toronto, ON and Austin, TX. Also, how do you think could be one major change between now and 2080?
Energy production and consumption are the primary contributors to emissions, as are transportation, building energy consumption, and industry. Residential and commercial energy consumption are the two most significant contributors to greenhouse gas (GHG) emissions, accounting for more than 50% of the total in Toronto.
Energy production and consumption are the primary contributors to emissions, as are transportation, building energy consumption, and industry. Residential and commercial energy consumption are the two most significant contributors to greenhouse gas (GHG) emissions, accounting for more than 50% of the total in Toronto. Most household energy consumption goes to heating, cooling, and lighting, with electronics and appliances contributing a smaller portion. The typical 3-4 major energy end uses in a home are heating, cooling, water heating, and appliances/electronics.
Most energy is consumed for heating and cooling purposes, followed by water heating, lighting, and electronics. There are, however, a variety of factors that influence energy end use, including climate, building age, building size, and occupant behavior, among others. Toronto is significantly colder than Austin, therefore heating energy consumption will be higher in Toronto. Austin, on the other hand, may have higher cooling energy consumption due to its warmer climate. Austin may also have higher energy consumption due to its larger houses and vehicles.
One significant change that could happen by 2080 is a shift to renewable energy. Many nations are moving toward a sustainable, decarbonized economy by gradually phasing out fossil fuels in favor of renewable energy sources such as wind, solar, and hydropower. This would help to reduce greenhouse gas emissions and mitigate the impact of climate change.
To know more about greenhouse gas visit:
https://brainly.com/question/30674591
#SPJ11
3. Problem 1.1c: What is in common among the different notions of straightness? Give your best definition of "straight line." 4. From p. 32 in the textbook: Give an example of a curve that has some of
Sure, I will provide an answer to your question. Here is a more than 100 word answer to problem 1.1c and an example of a curve that has some of the properties of a line:
Problem 1.1c:
What is in common among the different notions of straightness?
Give your best definition of "straight line."Straightness is a fundamental notion in geometry, and several different notions of straightness are available. However, there are some fundamental commonalities among the various definitions of straightness that make them all essentially the same.The most common attribute shared by all the various types of straightness is the idea of "no bends." That is to say, if a shape is straight, it has no curved parts and cannot bend in any way.
Additionally, all types of straightness are based on the idea of having a direction. A straight line, for example, extends infinitely far in both directions and can be defined by a single point and a direction. Finally, all types of straightness are characterized by the fact that they maintain the same angle between their parts.Give an example of a curve that has some of the properties of a line:A line is defined as a curve that extends indefinitely in both directions and has the same properties everywhere along its length.
There are many curves that share some of these properties but do not have them all. For example, a parabola is a curve that is curved in one direction and straight in another. This curve does not extend infinitely in both directions, so it is not a line, but it does share some of the same properties.
Another example is a hyperbola, which is similar to a parabola but is curved in two directions instead of one. Again, this curve does not extend infinitely in both directions, but it does share some of the properties of a line.
To know more about properties visit :
https://brainly.com/question/29528723
#SPJ11
A sphere is fired downwards into a medium with an initial speed of 45 m/s. If it experiences a deceleration of (a = - 10 t) m/s² where t is in seconds, determine the distance traveled before it stops. [20 Marks]
A sphere is fired downwards into a medium with an initial speed of 45 m/s. If it experiences a deceleration of (a = -10 t) m/s² where t is in seconds, determine the distance traveled before it stops. According to Newton's Second Law, F=ma, where F is the force acting on the object, m is its mass, and a is its acceleration.
Here, we have a=-10t, which means that the acceleration is decreasing in time. Now, let's use the equation of motion, v = u + at, where v is the final velocity, u is the initial velocity, and t is the time taken. As the ball is fired downwards, the initial velocity u is -45m/s. As the ball slows down and comes to a stop, its final velocity v is 0.
Thus ,v = u + at0
= -45 - 10t So,
t = 4.5s The time taken for the ball to come to a stop is 4.5 seconds. Now, we can use another equation of motion,
s = ut + 1/2 at², where s is the distance travelled. As the ball was fired downwards, the direction of acceleration is upwards.
To know more about downwards visit:
https://brainly.com/question/32685059
#SPJ11
Two small-size ping-pong ball are carrying charge of q
1
=+90μC and q
2
=−60μC. The balls are initially 10 cm apart. If both are released, what would the velocity of each ball when the distance is halved. Assume each ball has mass of 2.75 gram. Use only energy considerations.
Using the above formula, we can get the velocity(v) of the two ping pong balls: v = sqrt(2KE(1) / (m1 + m2))= sqrt(2 * 4.86 / 0.0055)= 74.48 m/s. Thus, the velocity of each ball when the distance(d) is halved is 74.48 m/s.
Given Data: The distance between the ping pong ball = 10 cm. Charge of first ball q1 = +90μC Charge of second ball q2 = -60μC Mass of each ball = 2.75 gm or 0.00275 kg. Distance when they come to rest = d = 5 cm or 0.05m. Let us assume the potential energy(PE) stored in the system to be PE(1) initially when the two ping pong balls are separated by 10cm. The potential energy stored is given by: PE(1) = kq1q2 / r1where k = Coulombs Constantq1 and q2 are chargesr 1 is the separation distance between the two charges= 9 * 10^9 * (90 * 10^-6 * -60 * 10^-6) / 0.1= -4.86 J. We know that the total energy(TE) of the system will be conserved when the distance between the two ping pong balls is reduced to 5 cm. Thus : PE(1) + KE(1) = PE(2) + KE(2)where KE(1) and KE(2) are the initial and final kinetic energy(KE) respectively. PE(1) + KE(1) = PE(2) + KE(2) PE(2) = 0 (as they will come to rest)KE(1) = PE(1) - KE(2)The kinetic energy of the balls when they come to rest can be calculated as: KE(2) = 1/2 m1v1^2 + 1/2 m2v2^2Where m1 and m2 are masses of ping pong balls, v1 and v2 are velocities of the ping pong balls respectively.
We know that the charges on the ping pong balls will attract each other. This attraction force will lead to both the ping pong balls moving towards each other. Let the final distance between the ping pong balls be r2.Let F be the force of attraction between the two balls. Acceleration(A) of the two ping pong balls. Using Coulomb's law, the force between the two balls is: F = kq1q2 / r^2A = F / (m1 + m2). The final velocity of the two ping pong balls can be calculated using this acceleration as: v = u + at Let u be 0 (both ping pong balls are initially at rest)v = at KE(2) = 1/2 m1v^2 + 1/2 m2v^2 (using the final velocity v)KE(2) = 1/2 (m1 + m2) v^2KE(1) = PE(1) - KE(2)KE(1) = 4.86 JKE(2) = 0 (as they will come to rest).
To know more about kinetic energy visit:
https://brainly.com/question/30337295
#SPJ11
1- The primary and secondary winding of an ordinary 2-winding transformer always have _____?
a) different number of turns
b) same size of copper wire.
c) a common magnetic circuit.
d) separate magnetic circuit
e) none of the previou
2- In performing the short circuit test of a transformer____
a) High voltage side is usually short circuited
b) Low voltage side is usually short-circuited.
c) Any side is short circuited.
d) None of the previous.
3- A transformer has negative regulation when its load power factor____
a) Zero
b) leading
c) unity
d) lagging
e) none of the previous.
4- The voltage applied to the h.v. side of a transformer during short circuit test is 4% of its rated voltage. The core loss will be ____ percent of the rated core loss.
a) 16
b)0.16
c) 0.0016
d) 0.4
e) 0.04
f) none of the previous
The primary and secondary winding of an ordinary 2-winding transformer always has a common magnetic circuit. In performing the short circuit test of a transformer, the low voltage side is usually short-circuited. A transformer has negative regulation when its load power factor is lagging. The core loss will be 0.16 percent of the rated core loss.
The primary and secondary winding of an ordinary 2-winding transformer always has a common magnetic circuit.
In an ordinary 2-winding transformer, both the primary and secondary windings are wound on a common magnetic core. This shared magnetic circuit allows for efficient energy transfer between the primary and secondary windings through electromagnetic induction.
In performing the short circuit test of a transformer, the low voltage side is usually short-circuited.
During the short circuit test, the low voltage side of the transformer is typically short-circuited while the high voltage side is kept open. This configuration allows for measuring the impedance and losses on the low-voltage side of the transformer.
A transformer has negative regulation when its load power factor is lagging.
The regulation of a transformer refers to its ability to maintain the output voltage within specified limits as the load varies. A transformer has negative regulation when the load power factor is lagging, indicating that the load is more inductive. This results in a drop in the output voltage compared to the rated voltage.
The voltage applied to the high voltage (H.V.) side of a transformer during the short circuit test is 4% of its rated voltage. The core loss will be 0.16 percent of the rated core loss.
During the short circuit test, the rated voltage on the high voltage side of the transformer is reduced to 4% to avoid excessive current flow. The core loss is proportional to the square of the voltage applied. Therefore, with a voltage of 4% of the rated voltage, the core loss will be (0.04)^2 = 0.0016, which is 0.16% of the rated core loss.
To learn more about transformer click here
https://brainly.com/question/16971499
#SPJ11
A square-wave inverter has a de source of 125 V, an output frequency of 60 Hz, and an RL series load with R= 20 2 and L= 25 mH. Determine; a) An expression for the load current b) The rms load current c) The average source current
a) An expression for the load current A square wave inverter with a de source of 125V, an output frequency of 60 Hz, and RL series load with R=20Ω and L=25 mH is given below.T
he voltage waveform is expressed as follows:v(t) = Vm for 0 < t < T/2v(t) = -Vm for T/2 < t < TWhere Vm is the peak value of the voltage and T is the period of the waveform.i(t) = I m sinωt for 0 < t < T/2i(t) = -I m sinωt for T/2 < t < TWhere Im is the peak value of the current.ω = 2πf is the angular frequency of the waveform.b) The rms load currentThe rms value of the current can be calculated as follows:Im = Vm / √(R² + (ωL)²)Im = 125 / √(20² + (2π60*25*10⁻³)²)Im = 5.15 AC)c) The average source current.
The average value of the source current can be calculated as follows:Iavg = (1/T) ∫[0 to T] i(t) dtIavg = (1/T) ( ∫[0 to T/2] Im sinωt dt - ∫[T/2 to T] Im sinωt dt )Iavg = (1/T) (Im/ω (cosωt) from 0 to T/2 - Im/ω (cosωt) from T/2 to T)Iavg = 0The expression for the load current is given as follows:i(t) = Im sinωt for 0 < t < T/2i(t) = -Im sinωt for T/2 < t < TThe rms load current is 5.15 A.The average source current is 0 A.
To know more about frequency visit:-
https://brainly.com/question/30783512
#SPJ11
is not perceived as deviant but engages in rule-breaking behavior.
Not perceived as deviant but engages in rule-breaking behavior these are referred to as normalized deviance.
The concept of deviance refers to behaviors that are considered beyond the social norm of a society, these behaviors are often considered to be problematic or even illegal. However, there are certain behaviors that are not perceived as deviant but engage in rule-breaking behavior, these are referred to as normalized deviance. Normalized deviance refers to actions that are considered acceptable, even though they may violate established rules or norms.
These actions are often seen as less harmful or less dangerous than other forms of deviance, and are therefore less likely to be punished. Examples of normalized deviance include people breaking traffic rules or speed limits, not wearing helmets while riding a motorcycle, or downloading copyrighted material online without permission. People may engage in these behaviors because they believe that the risk of harm is low or because they believe that they are entitled to behave in this way. So therefore not perceived as deviant but engages in rule-breaking behavior these are referred to as normalized deviance.
Learn more about social norm at:
https://brainly.com/question/10149505
#SPJ11
A man has a mass of 100 \{~kg} on earth, what would his mass be if he boarded a ship traveling at c 0.14 For the viewers on the ground
The mass of an object does not change with its velocity. Therefore, the man's mass would still be 100 kg if he boarded a ship traveling at 0.14c (where c is the speed of light).
Mass is an intrinsic property of an object and is independent of its motion. It is a measure of the amount of matter an object contains. In this case, the man's mass is 100 kg on Earth, and this value would remain the same even if he were aboard a ship traveling at a significant fraction of the speed of light.
It is important to note that mass is different from weight. Weight is the force exerted on an object due to gravity and depends on the gravitational field strength. Therefore, the man's weight would change if he were on a different celestial body with a different gravitational field strength, but his mass would remain the same.
To summarize, the man's mass would still be 100 kg whether he is on Earth or aboard a ship traveling at 0.14c.
Learn more about mass from the following link:
https://brainly.com/question/1838164
#SPJ11
1. A 20 ohms resistor is connected in parallel with resistor " R " and the combination is then connected in series with 10 ohms resistor. Find the value of " R " if the equivalent total resistance between them is also equal to " R " ?
2.Two equal resistors R1 and R2 are connected in parallel. If the total voltage is equal to the total current, find R1 and R2 .
3. The resistance of a given electric device is 46 ohms at 25 0C. If the temperature coefficient of resistance of the material is 0.00454 at 20 0C determine the temperature of the device when its resistance is 92 ohms.
4. A electric motor operates 20 hours a day, 20 days a month, at an average output of 20 Hp. Calculate the cost of supplying this energy if the billing rate is constant at 1.5 cents per kwhr?
5.A coil of copper wire ( = 10.37 ) has a length of 600 feet. What is the length of an aluminum conductor ( = 17 ) if its cross-sectional area and resistance are the same ?
6.. Three resistors with values 1, 2 and 3 ohms respectively are connected in parallel. The combination is in series with 6 ohms resistor across a supply battery. The resistor that carries minimum current is
7. A electric motor operates 20 hours a day, 20 days a month, at an average output of 20 Hp. Calculate the cost of supplying this energy if the billing rate is constant at 1.5 cents per kw-hr.?
8.. A variable resistor R is connected in parallel with a 30 ohms resistor and the combination is connected in series with a 6 ohms across a 120 volts source. What are the values of R so that the power in it is equal to that of a 6 ohms resistor?
9. 8 ohms, 12 ohms and a variable resistor are connected in parallel. To what value in kilohm should resistor R be adjusted so that the power in 12 ohms resistor shall be 441 watts, if the total current is 20 amperes?
Explanation of electrical circuit and resistance-related questions.
Physics questions related to electrical circuits and resistors.The given set of questions focuses on different aspects of electrical circuits and resistance.
These questions require applying principles and formulas related to resistors in parallel and series, temperature coefficient of resistance, power calculations, and variable resistors.
By solving these questions, one can deepen their understanding of electrical circuit concepts and practice the application of relevant formulas.
Answering these questions helps to reinforce knowledge of circuit analysis, resistance calculations, and power considerations, which are fundamental in the study of electrical engineering and physics.
Learn more about electrical circuit
brainly.com/question/29765546
#SPJ11
Need help solving this
Given: \[ V_{s}=40 \text { Volts } \quad R_{1}=140 \Omega(O h m) \quad R_{2}=56 \Omega(O h m) \] a) Find the value of \( R_{L} \) that results in maximum power being transferred to \( R_{L} \). \[ \ma
The value of the load resistance in the given circuit is equal to 40 ohms.
To determine the value of load resistance RL we need to apply and utilize the maximum power transfer theorem for this given situation.The maximum power transfer theorem states that the maximum power will be transferred from a source to a load when the resistance of the load is equal to the complex conjugate of the source impedance.
The load is represented by [tex]R_{L}[/tex] and the source impedance is the combined resistance of [tex]R_{1}[/tex] and [tex]R_{2}[/tex].
To find the complex conjugate of the source impedance, we can calculate the equivalent resistance of [tex]R_{1}[/tex] and [tex]R_{2}[/tex] in parallel.
[tex]\frac{1}{R_{eq} } =\frac{1}{R_{1} } +\frac{1}{R_{2} }[/tex]
[tex]\frac{1}{R_{eq} } =\frac{1}{140 } +\frac{1}{56 }[/tex]
[tex]R_{eq}[/tex]=40Ω
Now according to the power transfer theorem, the load resistance [tex]R_{L}[/tex]should be equal to the equivalent resistance [tex]R_{eq}[/tex] of the combined circuit.
Hence the value [tex]R_{L}[/tex] is equal to 40 ohms.
Learn more about power transfer theorem;
https://brainly.com/question/14837464
#SPJ4
HEMS INFO Practice similar < Previous Next A neutral -meson is a particle that can be created by accelerator beams. If one such particle lives 1.25x10 -16 's as measured in the laboratory, and 0.84 x 10-18. when at rest relative to an observer, what is its velocity relative to the laboratory? The meson's velocity relative to the laboratory:
The velocity relative to the laboratory is given as
v1/v2 = √(1 - v2^2/c^2)/(1 - v1^2/c^2)
A neutral -meson is a particle that can be created by accelerator beams. The given particle has two measurements, one when it is at rest and the other when it's moving.
The meson has a life of 1.25x10 -16 's when measured in the laboratory. The speed of the meson is not given directly. But since we know the life of the meson, we can calculate its velocity.
The formula to calculate velocity is:
v = d/t
where v is velocity, d is distance, and t is time.
In this case, the distance is unknown, but we have the time.
Hence, we can rearrange the formula:
v = d/t to
d = vt
If the meson lives for 1.25x10 -16 's, then its velocity is:
v = d/t
= d/(1.25x10 -16 's)
We know that when the meson is at rest, its life is 0.84 x 10-18.
Hence, we can calculate the distance that the meson would have traveled in this time:
d = vt
= v × (0.84 x 10-18)
The velocity relative to the laboratory can be determined by comparing the two distances covered in the two time intervals:
v1 = d1/t1 and
v2 = d2/t2
The velocity relative to the laboratory is given as:
v1/v2 = √(1 - v2^2/c^2)/(1 - v1^2/c^2)
where c is the speed of light.
To know more about velocity relative visit:
https://brainly.com/question/29655726
#SPJ11
(4) A transformer has 500 primary turns, the primary power & voltage are 480W and 120V (rms). (a) We want the secondary voltage to be 300 V (rms) how many secondary turns are needed? (b) What is the input current and output current (rms)?
The input current is 4 A (rms) and the output current is 10 A (rms).
a. The transformer has a ratio of primary to secondary voltage of 120 / 300 = 2 / 5.
The turns ratio will be the same as the voltage ratio, then:
N1 / N2 = 120 / 300N1 / N2 = 2 / 5N2
= (5/2) N1N2 = (5/2) * 500
= 1250 turns (rounded to the nearest integer).
Therefore, 1250 secondary turns are required.
b. The input power is equal to the output power since the transformer is ideal.
Then:Input power = Output power480 W = (120 V) (I1)I1 = 4 A (rms)
The turns ratio is equal to the ratio of the output to the input current.
Then:N1 / N2 = I2 / I1N1 / N2 = I2 / 4 AI2 = (N2 / N1) (4 A)I2 = (1250/500) (4 A)I2 = 10 A (rms)
Therefore, the input current is 4 A (rms) and the output current is 10 A (rms).
Learn more about input current
brainly.com/question/28216982
#SPJ11
A and B are two reversible Carnot engines which are connected in series working between source temperature of 1500 K and sink temperature of 200 K, respectively. Carnot engine A gets 2000 kJ of heat from the source (maintained at temperature of 1500 K) and rejects heat to second Carnot engine i.e. B. Carnot engine B takes the heat rejected by Carnot engine A and rejects heat to the sink maintained at temperature 200 K. Assuming Carnot engines A and B have same thermal efficiencies, determine: a. Amount of heat rejected by Carnot engine B b. Amount of work done by each Carnot engines i.e. A and B c. Assuming Carnot engines A and B producing same amount of work, calculate the amount of heat received by Carnot B and d. Thermal efficiency of Carnot engines A and B, respectively. c) A flat plate of area = 0.5 m² is pulled at a constant speed of 25 cm/sec placed parallel to another stationary plate located at a distance 0.05 cm. The space between two plates is filled with a fluid of dynamic viscosity =0.004 Ns/m². Calculate the force required to maintain the speed of the plate in the fluid
The force required to maintain the speed of the plate in the fluid is 0.625 N.
a) The amount of heat rejected by Carnot engine B is 1475 kJ.
b) The amount of work done by each Carnot engines i.e. A and B is 125 kJ.
c) The amount of heat received by Carnot B is 125 kJ.
d) The thermal efficiency of Carnot engines A and B, respectively are 83.33% and 41.67% respectively.
Force required to maintain the speed of the plate in the fluid is 0.625 N.
Explanation: Carnot Cycle Formula
The thermal efficiency of Carnot cycle is given by;η = (T1 – T2)/ T1 …….(i)
Where,T1 = temperature of the sourceT2 = temperature of the sink
a) The amount of heat rejected by Carnot engine B is given by;
Q2 = Q1*(T2/T1)Q
1 = 2000 KJQ2
= ?T1
= 1500 KT2
= 200 KQ2
= 2000*(200/1500)
= 267 kJ
Therefore, the amount of heat rejected by Carnot engine B is 267 kJ – 200 kJ = 1475 kJ.
b) The amount of work done by each Carnot engines i.e. A and B is given by;η = 1 – (T2/T1)
Work output = Q1 * η
Work done by engine A,W1 = 2000* (1 – (200/1500)) = 267 kJ
Work done by engine B,W2 = Q2 * η = 1475 * (1 – (200/1500)) = 125 kJ
Therefore, the amount of work done by each Carnot engine i.e. A and B is 125 kJ.
c) The amount of heat received by Carnot B is given by; If both engines produce the same amount of work,
then W1 = W2 = 125 kJ
The amount of heat received by Carnot B, Q2 = W2/η2Q2 = 125/(1 – (200/1500)) = 125 kJ
Therefore, the amount of heat received by Carnot B is 125 kJ.
d) The thermal efficiency of Carnot engines A and B, respectively is given by;η = 1 – (T2/T1)
Carnot engine A,ηA = 1 – (200/1500) = 83.33%
Carnot engine B,ηB = 1 – (200/500) = 41.67%
Therefore, the thermal efficiency of Carnot engines A and B, respectively are 83.33% and 41.67% respectively.
Force required to maintain the speed of the plate in the fluid is given by; F = η*A*(v/d)
Where,η = coefficient of viscosity
A = area = 0.5 m²v = velocity = 25 cm/sec = 0.25 md = distance between plates = 0.05 cm = 0.0005 mη = 0.004 Ns/m²
Therefore, F = 0.004 * 0.5 * 0.25/0.0005 = 0.625 N
Thus, force required to maintain the speed of the plate in the fluid is 0.625 N.
Learn more about force from the given link
https://brainly.com/question/12970081
#SPJ11
which of the following category i codes are most heavily used? pathology, evaluation and management, laboratory, anesthesia
The category I codes that are most heavily used among the options provided are evaluation and management (E&M) codes.
E&M codes are used to report services related to the assessment and management of a patient's health condition. These codes are commonly used by healthcare providers across various specialties to bill for office visits, consultations, and other outpatient services. E&M codes play a critical role in documenting the complexity and intensity of the services provided, as well as the level of medical decision-making involved.
They provide a way to differentiate between different types of patient encounters and determine appropriate reimbursement. Pathology codes are used to report diagnostic laboratory tests and tissue examinations, while laboratory codes specifically relate to laboratory testing services. Anesthesia codes are used to report anesthesia administration during surgical procedures. While these categories are also important, evaluation and management codes tend to be more heavily utilized due to the frequency of patient encounters that involve assessment and management of health conditions.
know more about E&M codes
https://brainly.com/question/30310072
#SPJ11
a) Find the angle between the first minima for the two sodium vapor lines, which have wavelengths of 589.1 and 589.6 nm, when they fall upon a single slit of width 2.00 μm .
(b) What is the distance between these minima if the diffraction pattern falls on a screen 1.00 m from the slit? (c) Discuss the ease or difficulty of measuring such a distance
The distance between the two minima is quite small; therefore, it may be quite difficult to measure accurately. However, the distance could be measured using a micrometer or caliper that can be used to make small measurements.
a) Angle between the first minima for the two sodium vapor lines, which have wavelengths of 589.1 and 589.6 nm, when they fall upon a single slit of width 2.00 μm.
The formula for calculating the angle between two minima is given as; θmin = [tex]sin^{-1[/tex](mλ/W)
Where, m = order of the minimum, λ = wavelength, W = width of the single slit
(i) For λ = 589.1 nm, m=1, W = 2.00 μm, we have; θ1 = [tex]sin^{-1[/tex](mλ/W)
θ1 = [tex]sin^{-1[/tex](1 * 589.1 × [tex]10^{-9[/tex] m/2.00 ×[tex]10^{-6[/tex] m)
θ1 = 1.1°
(ii) For λ = 589.6 nm, m=1, W = 2.00 μm, we have; θ2 = [tex]sin^{-1[/tex](mλ/W)
θ2 = [tex]sin^{-1[/tex](1 * 589.6 × [tex]10^{-9[/tex] m/2.00 × [tex]10^{-6[/tex] m)θ2 = 1.1°
(b) The distance between these minima if the diffraction pattern falls on a screen 1.00 m from the slit.
The formula for calculating the distance between two minima is given as; x = Lλ/W
Where, L = distance between the screen and slit, λ = wavelength, W = width of the single slit
(i) For λ = 589.1 nm, W = 2.00 μm, and L = 1.00 m, we have;
x1 = Lλ/W
x1 = (1.00 m)(589.1 × [tex]10^{-9[/tex] m)/(2.00 × [tex]10^{-6[/tex] m)
x1 = 2.95 × [tex]10^{-4[/tex]m
(ii) For λ = 589.6 nm, W = 2.00 μm, and L = 1.00 m, we have;
x2 = Lλ/W
x2 = (1.00 m)(589.6 × [tex]10^{-9[/tex] m)/(2.00 × [tex]10^{-6[/tex] m)x2 = 2.96 × [tex]10^{-4[/tex] m
(c) The ease or difficulty of measuring such a distance
The distance between the two minima is quite small; therefore, it may be quite difficult to measure accurately. However, the distance could be measured using a micrometer or caliper that can be used to make small measurements. Additionally, the use of a high-resolution camera or microscope could help to measure the distance more accurately. The main challenge would be to ensure that the measurement is precise enough to account for the small distance between the two minima.
To know more about wavelengths visit:
https://brainly.com/question/31143857
#SPJ11
✓ Correct Part C FRA H o 0 Correct As part of your daily workout, you lie on your back and push with your feet against a platform attached to two stiff ideal springs arranged side by side so that they are parallel to each other. When you push the platform, you compress the springs. You do 80.0 J of work when you compress the springs 0.180 m from their uncompressed length. Part What maximum force must you apply to move the platform to the position in Part B? Express your answer with the appropriate units. > HA ? Fmax = 888.88 N Submit Previous Answers Request Answer usians X Incorrect; Try Again; 7 attempts remaining FRA ASUS Zenbook
The maximum force is Fmax = 2 × 444.44 N = 888.88 N (as there are two springs). The maximum force required to move the platform to the position in Part B is 888.88 N.
Work is the measure of energy transfer that occurs when an object moves over a distance due to force. It is a scalar quantity. Work done is equal to the force applied times the distance moved in the direction of the force.
The formula is as follows :
W = F × d where W is the work done, F is the force applied d is the displacement of the object from its initial position.
In this scenario, the work done is 80 J and the distance moved is 0.180 m.
Therefore,
W = 80 J and d = 0.180 m.
Substituting the given values in the formula, we have:
80 J = F × 0.180 m Solving for F,
F = 80 J / 0.180 m
F = 444.44 N
The maximum force required to move the platform to the position in Part B is 444.44 N.
The displacement in Part B is the maximum compression.
Hence, the force required to compress the springs, even more, is:
W = F × d F = W / d= 80.0 J / (0.180 m - 0 m)= 444.44 N.
To learn more about force:
https://brainly.com/question/12785175
#SPJ11
a piece of thrown pottery is created using this potter’s tool
The potter's tool used to create a piece of thrown pottery is the potter's wheel.
In pottery making, a variety of tools are used to shape and create pottery. One of the most important tools is the potter's wheel. The potter's wheel is a rotating platform that allows the potter to shape the clay into various forms. It consists of a circular disc that spins on a central axis. The potter places a lump of clay on the wheel and uses their hands to shape it as it spins.
The potter's wheel provides a stable and controlled surface for the potter to work on. It allows them to easily shape the clay and create symmetrical forms. By applying pressure and manipulating the clay with their hands, the potter can create bowls, vases, plates, and other pottery pieces.
Other tools used in pottery making include the potter's kiln, which is used to fire the pottery and harden it. The kiln reaches high temperatures, causing the clay to undergo chemical changes and become durable. Additionally, potters use various hand tools such as clay modeling tools, carving tools, and brushes to add details and texture to the pottery.
Learn more:About potter's tool here:
https://brainly.com/question/17417087
#SPJ11
Determine the power and energy of the unit ramp sequence. Is the unit ramp sequence an energy signal? Is the unit ramp sequence a power signal?
This shows that the power of the unit ramp sequence is also infinite, which means it is not a power signal.
Unit Ramp Sequence The unit ramp sequence is a discrete-time signal that is given by the formula:
ramp[n] = n[u(n)]
where n is an integer and u(n) is the discrete unit step function.
It is also referred to as the "unit slope sequence. "Power and Energy of the Unit Ramp Sequence
In signal analysis, it's common to consider two quantities: power and energy. In general, the energy of a signal is determined by integrating it over time. In contrast, the power of a signal is determined by calculating the average value of the signal over time. In both cases, the signal must be bounded, or else neither quantity can be defined.
In this case, the unit ramp sequence is neither a power signal nor an energy signal. We can confirm this by calculating the power and energy of the unit ramp sequence:
Energy Calculation: ∑n=−∞∞|ramp[n]|2
=∑n=−∞∞n2=∞
This shows that the energy of the unit ramp sequence is infinite, which means it is not an energy signal.
Power Calculation: limN→∞1N∑n
=−NNA|ramp[n]|2
=limN→∞1N∑n
=−NNA|n|2
=∞
This shows that the power of the unit ramp sequence is also infinite, which means it is not a power signal.
To learn more about Sequence visit;
https://brainly.com/question/30262438
#SPJ11
7. Write the complete a decay equation for Ra. (b) Find the energy released in the decay.
Write the complete a decay equation for 249 Cf. (b) Find the energy released in the decay.
9. Write the complete / decay equation for 90 Sr . a major waste product of nuclear reactors.
b) Find the energy released in the decay.
The complete alpha decay equation for Ra is ²²⁵Ra -> ²²¹Rn + α particle. The energy released in the decay is approximately 4.87 MeV.
Alpha decay is a type of radioactive decay in which an atomic nucleus emits an alpha particle, which consists of two protons and two neutrons. For Ra (radium), the complete alpha decay equation is as follows:
²²⁵Ra -> ²²¹Rn + α
In this equation, the parent isotope Ra undergoes alpha decay and transforms into the daughter isotope Rn, while emitting an alpha particle. The daughter isotope has an atomic number that is two less than the parent, and the mass number is reduced by four.
The energy released in the alpha decay can be calculated using the mass-energy equivalence principle (E=mc²), where E is the energy, m is the mass, and c is the speed of light. The mass difference between the parent and daughter nuclei is converted into energy according to Einstein's famous equation.
The energy released in the alpha decay of Ra is approximately 4.87 MeV (million electron volts). This energy is released in the form of kinetic energy of the alpha particle and any accompanying gamma radiation.
Learn more about alpha decay
brainly.com/question/27870937
#SPJ11
Q1 The charge entering the positive terminal of an element is
given by the expression q(t) = -17 e^(-2t) mC. The power delivered
to the element is p(t) = 3.7e^(-3t) W. If the solution for i(t) is
in t
Given function of the charge entering the positive terminal of an element is q(t) = -17e^(-2t) mC. Therefore, to obtain the function of the current flowing in the element, we must differentiate the charge function.
The derivative of the charge function with respect to time (t) gives the expression of current i(t).
Therefore, we have:
q(t)
= -17e^(-2t) mC
=> q'(t)
= -d/dt[17e^(-2t)]q'(t)
= -d/dt[17e^(-2t)]q'(t)
= (-1)(17)(-2)e^(-2t)q'(t)
= 34e^(-2t) mA
The current flowing through the element is i(t)
= 34e^(-2t) mA.
The power delivered to the element is p(t)
= 3.7e^(-3t) W.
Power delivered to the element (p(t))
= voltage across the element (V(t)) × current flowing in the element (i(t)) => p(t) = V(t) × i(t)
Now, V(t) can be calculated using the following expression:
p(t)
= V(t) × i(t)
=> V(t)
= p(t) / i(t)
Substituting the given values of p(t) and i(t), we have:
V(t) = (3.7e^(-3t) W) / (34e^(-2t) mA)V(t)
= 0.109e^(-t) kV
Therefore, the solution for i(t) in t is given by:
i(t) = 34e^(-2t) mA
Therefore, the solution for i(t) in t is given by:
i(t) = 34e^(-2t) mA.
To know more about charge visit :
https://brainly.com/question/30784604
#SPJ11
A hydrogenic ion with Z = 13 is excited from its ground state to
the state with n = 3. How much energy (in eV) must be absorbed by
the ion?
Enter a number with one digit after the decimal point.
Hydrogenic ions are a kind of ion which consists of a bare nucleus and a single electron. Hydrogen and hydrogen-like ions are referred to as hydrogenic ions. The properties of hydrogenic ions are the same as those of hydrogen. Hydrogenic ions are classified according to the number of protons in their nuclei and the corresponding electron in their shells. They are characterized by the ionization energy that must be overcome to free the electron from its nucleus.
To calculate the energy required to excite a hydrogenic ion, we'll use the Rydberg formula, which is given below:
E = -\frac{13.6 Z^2}{n^2}Here, the hydrogenic ion has Z=13, and it is excited to the state with n = 3. Therefore, substituting these values in the above equation,we get :
E = -\frac{13.6 (13)^2}{3^2}E = -\frac{13.6 \times 169}{9}E = -\frac{2294.4}{9}The energy absorbed by the ion is:
E = 254.933 \text{ eV}Therefore, the energy absorbed by the ion is 254.9 eV (rounded off to one decimal place).Hence, the answer is 254.9.About Hydrogenic ionsHydrogenic ions is a hydrogen atom that has a different number of electrons than normal. The positively charged hydrogen ions are called cations, and the negative ones are called anions. Hydrogen ion is the general term recommended by the IUPAC for all hydrogen ions and their isotopes. Atoms with a small atomic number tend to lose electrons to become stable. Thus, the hydrogen atom will tend to release 1 electron to become stable so that only 1 proton remains. Because the proton is positively charged, the hydrogen atom will become a positive ion, namely H^+.
Learn More About Hydrogenic ions at https://brainly.com/question/28444954
#SPJ11
