a car drives straight down toward the bottom of a valley and up the other side on a road whose bottom has a radius of curvature of 115 m. at the very bottom, the normal force on the driver is twice his weight. at what speed was the car traveling, in m/s?

If the rate of pulling the wagon is increased, then the distance will be shortened as the force will be too great for the coefficient of friction to handle.

Distance is the measure of how far apart two objects are or how long it would take to travel between them. It is typically measured in terms of length, such as kilometers, meters, miles, feet, yards, or other units of length. Though it can also be measured in terms of time, such as hours, minutes, or seconds. Distance can be calculated using a variety of methods, such as using a ruler, using a map, or using a GPS device. Distance can be used to describe both physical and abstract concepts, such as the distance between two people or the distance between two ideas.

The distance that a wagon can be pulled when its handle is pulled at a 30 degree angle depends on a variety of factors, such as the friction between the wagon and the surface it is being pulled on, the weight of the wagon and the force being applied to the handle. Generally speaking, a heavier wagon will require more force to move it the same distance as a lighter wagon when pulled at the same angle.

In order to determine the distance that a wagon can be pulled at a 30 degree angle, it is necessary to calculate the force being applied to the handle and the coefficient of friction between the wagon and the surface. Once these two values are known, it is possible to calculate the maximum distance that can be traveled by applying the equation distance = force * coefficient of friction * cosine (30 degrees).

It is important to note that the distance will only be the maximum distance that can be traveled if the wagon is being pulled at a constant rate. If the rate of pulling the wagon is increased, then the distance will be shortened as the force will be too great for the coefficient of friction to handle.

To know more about distance click-
https://brainly.com/question/26550516
#SPJ1

If the blue side of magnet 1 is attracted to the north pole of magnet 2, then the blue side of is the south pole of magnet 1.

Magnet 1 is not labeled with its poles, so we cannot say for certain which pole is north and which is south. However, we know that opposite poles of magnets are attracted to each other.

Since the blue side of magnet 1 is attracted to the north pole of magnet 2, it can be inferred that the blue side of magnet 1 must be the south pole. This is because north and south poles are opposite, and if the blue side of magnet 1 is attracted to the north pole of magnet 2, it means that the green side is opposite to it, which means it is the north pole. In other words, the the green side of magnet 1 is the north pole and blue side of magnet 1 is the south pole.

To learn more about magnet pole visit: https://brainly.com/question/14997726

#SPJ4

Your question seems incomplete, but I suppose the complete question was:

"Half of magnet 1 is blue, and half is green, but the poles are not marked. On magnet 2, the north and south poles are marked. If the blue side of magnet 1 is attracted to the north pole of magnet 2, what is true about magnet 1?

Magnet 1 has neither a north or south pole.

The blue side is the north pole of magnet 1.

The blue side is the south pole of magnet 1.

The green side is the south pole of magnet 1."

In order to do a lab experiment on substitution reaction reactions, a requires teachers 0.75 kilos aluminum. How many aluminum atoms will be utilized in the

Describe replacement.

replacement explained 1: the replacement process or action; the replacement condition replacing someone, especially in a position or function Example Sentences for Synonyms Understanding Replacement

What distinguishes replacement from substitution?

Replacing someone or something with an analogous one is the act of doing so; "replacing the superstar will not be easy." replacing. Put another item or person in their place: "He sent Smith in for Johnson but the replacement came too late to help." Substitution, commutation, exchange.

To know more about replacement visit:

https://brainly.com/question/26676538

#SPJ4

The tension in the rope is 37 N. the rope is parallel to the slope. what is the tension in the rope.

what is tension ?

Tension is an emotional and mental state that can occur in response to stress, anxiety, fear, or excitement. It is often experienced as a feeling of tightness in the chest and neck area and can be accompanied by physical symptoms such as increased heart rate, sweating, and shallow breathing.

Tension can be triggered by a variety of situations, including conflict, deadlines, public speaking, financial pressures, and changes in relationships. It can also be caused by physical conditions such as pain and fatigue, as well as by negative thoughts and feelings, including worry, fear, and anger.

To learn about more tension.

https://brainly.com/question/24994188

#SPJ4

When ground speed increases, rate of descent must increase.

What is Speed ?

One such measurable metric is speed, which calculates the ratio between the distance an object travels and the time needed to cover that distance. Let's explore speed in-depth in this session.

Speedometers are used to measure speed in moving vehicles. Odometers are used to calculate the distance travelled. A graph can be used to calculate speed as well. The distance-time graph aids in comprehending an object's speed.

The distance travelled in relation to the time it took to travel that distance is how speed is defined. As speed only has direction and magnitude, it is a scalar quantity.

Learn more about Speed from given link

https://brainly.com/question/13943409

#SPJ4

When ground speed increases, the rate of descent also increases.

Speed is a scalar quantity that represents the rate of change of an object's position with respect to time. It is typically measured in units of distance per time, such as meters per second or miles per hour. Speed can also be represented as velocity, which is a vector quantity that includes both the magnitude of the speed and the direction of motion.Thus, the metre per second (m/s) is the SI unit of speed.

A change in wind direction can have a significant effect on maintaining a 3 degree glideslope at a constant true airspeed because it can affect the aircraft's ground speed and rate of descent.

If the wind direction changes such that it is now blowing from the front, it can cause a headwind component that will decrease the ground speed and increase the rate of descent. The pilot will have to reduce the thrust in order to maintain the constant true airspeed and the 3 degree glideslope.

If the wind direction changes such that it is now blowing from the rear, it can cause a tailwind component that will increase the ground speed and decrease the rate of descent. The pilot will have to increase the thrust in order to maintain the constant true airspeed and the 3 degree glideslope.

To know more about speed, visit:

brainly.com/question/28224010

#SPJ4

The electric field inside a parallel plate capacitor in a vacuum can be determined using Coulomb's law and the surface charge density on one of the plates. If one plate has a surface charge density and the other plate is neutral, the electric field between the plates will be in the direction of the plate with the surface charge density.

The electric field can be defined as the electric force per unit charge. The direction of the field is assumed to be the direction of the force it would exert on a positive test charge. The electric field is radially outward from a positive charge and radially in toward a negative point charge.

According to Coulomb's law, the force of attraction or repulsion between two charged bodies is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.

To know more about the charge, visit here:

https://brainly.com/question/3412043

#SPJ4

Athletes use this fact to initiate spins by applying a force to the edge of their body, such as their hands or feet, which is not aimed at the center of mass.

This causes their body to rotate rapidly and spin around, giving them the momentum to fly through the air.

Gymnasts use this technique to spin around the high bar or the floor, figure skaters and ice dancers use it to spin around the ice, and divers use it to spin around the diving board before they enter the water.

What is force?

Force is an influence that causes an object to change its velocity or shape.

It can be a push or a pull, and it can be applied by an object, a person, or even gravity.

Force is measured in terms of mass and acceleration, and it is usually expressed in units of Newtons (N).

To learn more about force

Here: https://brainly.com/question/12785175

#SPJ4

The velocity at which the bucket spins is 4.91m/s and the range of speeds is  between 4.91 m/s and 17.3 m/s.

a) The diagram is attached

b) FN - mg = m(v²/r)

c) v = 4.91 m/s

d) (4.91 < v < 17. 3 ) m/s

a. The free-body diagram for the glass when it is at the top of the circle would show the glass being acted upon by several forces. At the top of the circle, the glass is subjected to its weight (mg) acting downward, the normal force (FN) exerted by the bucket on the glass, and the tension (T) in the string.

b. The net force on the glass at the top of the circle can be represented by the following equation:

FN - mg = m * a

FN - mg = m(v²/r)

where FN is the normal force, m is the mass of the glass, g is the acceleration due to gravity, and a is the acceleration of the glass.

c. To prevent the glass from falling out, the normal force between the glass and the bucket has to be greater than zero, meaning the tension force should be greater than the weight of the glass. So we can use the net force equation.

T = m (v² / r) + mg

T = (0.5 kg)(v² / 1.5 m) + (0.5 kg)(9.8 m/s^2)

T > 0

Solving for v we get:

v > √( 9.8*1.5 ) = 4.91 m/s

d. The tension on the string is given by the equation T = m(v²/r)

Therefore, tension on the string is greater than 100 N when v > √(100*1.5/0.5) = √(300) = 17.3 m/s

Therefore the range of speeds she can keep the glass in the bucket and prevent the string from breaking is between 4.91 m/s and 17.3 m/s.

Learn more on net force here;

https://brainly.com/question/4931057

#SPJ1

Answer:

s = 15 m

Explanation: speed = 2.5 m/s

                     time = 6s

          v = s / t

         2.5 = s/ 6

        2.5 × 6 = s

        s = 15 m

∴ The distance travelled by the pulse in 6s is 15 m.

The distance covered by a pulse which has a speed of 2.5m/s and time 6 seconds is 15 meters.

Speed is the distance covered by an object in a particular time period. It is a scalar quantity as it has only magnitude and no direction. The SI unit of speed is meter per second (m/s).

The speed of an object can be calculated by the formula:

Speed = Distance travelled/ Time taken

Speed = 2.5 m/s

Time = 6 seconds

Distance = Speed of the object × time taken

Distance = 2.5 × 6

Distance = 15 meters

Therefore, the distance covered by the pulse is 15 meters.

Learn more about Speed here:

https://brainly.com/question/28224010

#SPJ2

The range of the pendulum swing is 20 degrees, from -10 degrees to +10 degrees.

What is pendulum swing?

Pendulum swing is a phenomenon in which an object, suspended from a fixed point, swings back and forth in a regular rhythm. The pendulum is a simple mechanical system that has been used in clocks and other timepieces since the 16th century.

Pendulum swings are also used in amusement park rides and scientific experiments. A pendulum is usually made up of a mass, or bob, suspended from a string or wire, and is driven by gravity. As the pendulum swings, the force of gravity causes the bob to move in an arc, oscillating back and forth. The arc of the swing is determined by the length of the string, the mass of the bob, and the strength of the gravitational force pulling on it.

To learn about more pendulum swing

https://brainly.com/question/27860360

#SPJ1

The average January sea level temperature at points A, B, C, D, E, F, G, and H is 57.75 degrees Fahrenheit.

To find the average temperature of eight points, we added all the temperatures and divided them by the number of temperatures (8).

70 + 55 + 80 + 72 + 80 + 50 + 25 + 60 = 462

Then divide the sum of all temperatures by the number of temperatures (8) to find the average temperature: 462 / 8 = 57.75

So the average January sea level temperature at points A, B, C, D, E, F, G, and H is 57.75 degrees Fahrenheit.

Learn more about temperature here:

https://brainly.com/question/26533614

#SPJ4

Answer:

the photo is not loading ok this is your photo open this and see now

happy

Newborn main series stars can have masses between 0.1 and 150 times the mass of the sun. Less massive than the sun: is the most common star type in newly formed star clusters.

A amount pf matter in such a particle a object is represented by its mass, which is denoted by the symbol m. Inside the International System (SI), the kilogram serves as the default unit of mass (kg).

The resistance a body in matter offers to something like a change inside its speed or location as a result of the force that is applied is what it is in essence. The change a force applies produces a change that is smaller the more mass a body has.

To know more about mass visit:

brainly.com/question/28779148

#SPJ4

Newborn main series stars can have masses between 0.1 and 150 times the mass of the sun. Less massive than the sun: is the most common star type in newly formed star clusters.

A amount pf matter in such a particle a object is represented by its mass, which is denoted by the symbol m. Inside the International System (SI), the kilogram serves as the default unit of mass (kg).

The resistance a body in matter offers to something like a change inside its speed or location as a result of the force that is applied is what it is in essence. The change a force applies produces a change that is smaller the more mass a body has.

To know more about mass visit:

https://brainly.com/question/18064917

#SPJ4

A Van de Graaff generator is a type of electrostatic generator that uses a moving belt to build up and transfer a large electrical charge to a hollow metal sphere or other high voltage terminal.

The basic principle of operation is that a belt made of a non-conductive material, such as rubber, is driven by a motor, passing over a pulley at the bottom of the generator and a second pulley at the top.

The belt is charged by friction as it rubs against the bottom pulley, which is connected to a high voltage source.

As the belt moves, it carries the charge to the upper pulley, where it is transferred to the high voltage terminal, such as the hollow metal sphere. The charge is transferred from the belt to the terminal through a process called corona discharge.

Once the charge is transferred to the terminal, it can be used for various applications such as particle acceleration, X-ray generation, and research in high voltage phenomena.

A Van de Graaff generator can produce high voltage output, up to millions of volts, due to the accumulation of charges on the sphere.

The terminal is insulated from the ground to prevent any discharge until a high voltage is reached. This makes it useful for various scientific experiments and applications.

The value of resistivity and conductivity are mentioned below.

What is resistivity ?

A conductor with a unit cross-sectional area and unit length and its electrical resistance. Resistivity, a distinctive quality of any material, is helpful in comparing different materials based on their capacity to conduct electric currents. Poor conductors are identified by high resistance.

What is conductivity ?

A substance or material that permits electricity to flow through it is referred to as an electrical conductor. When voltage is given to a conductor, electrical charge carriers, often electrons or ions, travel easily from atom to atom.

Part a is explained by using the concept of diffusion current density and Einstein's relation

from semiconductor we have

T mobility

V= μE

Drift velocity

I = ncAvl

J also equal to E

σE= nevd

σ= nevd/E

σ= neμ

resistivity is reciprocal of conductivity

S= 1/σ=1/neμ

from Einstein's equation

∫= KT/ ne²Dn

Therefore, value of resistivity and conductivity are mentioned below.

Learn more about resistivity from the given link.

https://brainly.com/question/13735984

#SPJ4

The gravitational acceleration on the surface of Drift compare to the gravitational acceleration on the surface of the earth is  1/5th.

In physics, gravitational acceleration refers to the speed at which a body falls freely in a vacuum (and thus without experiencing drag). This is the constant acceleration brought on just by the gravitational pull.

In physics, the term "gravitational acceleration" (symbolized "g") is used to describe the strength of a gravitational field. It is measured in m/s2, or meters per second squared. At the earth's surface, 1 g is equivalent to 9.8 m/s 2.

Given,

[tex]M x_{D} = 5Mx_{E} \\R D = 5RE[/tex]

The gravitational acceleration on the surface of planet Drift -

[tex]gD= \frac{GMD}{ (rD)^{2} }[/tex]                                   (1)

The gravitational acceleration on the surface of planet Earth -

[tex]g E= \frac{GM E}{ (rE)^{2} }[/tex]                                    (2)

Divide equation (1) by (2) and we get:

[tex]\frac{gD}{gE} = \frac{ \frac{GMD}{ (rD)^{2} }}{ \frac{GM E}{ (rE)^{2} }}[/tex]

[tex]\frac{gD}{gE} = \frac{M D}{M E} (\frac{r E}{r D})^{2}[/tex]

[tex]g D = g E (\frac{M D}{M E} ) (\frac{e E}{r D} )^{2}[/tex]

Substitute all the known values in the above equation to determine the value of gD

[tex]g D = g E (\frac{5 M E}{M E} ) (\frac{R E}{5 R E} )^{2}[/tex]

[tex]= g E (5) (\frac{1}{5} )^{2}[/tex]

= [tex]\frac{g E }{5}[/tex]

Hence, the gravitational acceleration on the surface of Driff compare to the gravitational acceleration on the surface of the earth is 1/5th.

To learn more about gravitational acceleration from given link

https://brainly.com/question/14374981

#SPJ4

The magnitude of the momentum |p⃗ a,i| of piece a before the explosion is equal to the mass of the piece multiplied by its velocity.

What is the velocity?

Velocity is a physical quantity that describes the rate at which an object moves through space. A vector quantity it, meaning that its size and direction are both present.. Velocity is usually expressed as speed in a given direction, such as 10 meters per second (10 m/s) to the north. The average velocity of an object is its displacement divided by the elapsed time between the two points. Velocity is related to acceleration, which is the rate at which an object changes its velocity over time.

To learn more about velocity

https://brainly.com/question/24445340

#SPJ4

125 joules of energy are required to accelerate a 10-kg mass from rest to a speed of 5 meters per second on a horizontal, frictionless surface.

When a specific force is applied, an object accelerates less slowly the more mass it has. For instance, the acceleration is halved for a given force when an object's mass is twice.

The relationship between mass and acceleration is described by Newton's Second Law of Motion. According to his Second Law, the more mass an item has, the more force is required to accelerate it.

To know more about acceleration visit:

brainly.com/question/12550364

#SPJ4

The dynamic viscosity of the liquid is 0.277Ns if the kinematic viscosity and specific gravity of a liquid are and 0.79, respectively.

Given the kinematic viscosity of a liquid = 3.5 x 10^-4 m^2/s

The  specific gravity of a liquid  = 0.79

A conversion between kinematic and dynamic viscosity measurements can be made using density.

We know that, Specific gravity = density of liquid/density of water

The density of water = 1000kg/m^3

The density of liquid = 0.79 x 1000 = 790kg/m^3

Kinematic viscosity x liquid density = dynamic viscosity.

Dynamic viscosity = 3.5 x 10^-4 x 790 = 0.2765Ns

Hence the required dynamic viscosity of the liquid is 0.277Ns.

To learn more about viscosity click here https://brainly.com/question/2193315

#SPJ4

complete question: The kinematic viscosity and specific gravity of a liquid are 3.5 x 10^-4 m^2/s and 0.79, respectively. What is the dynamic viscosity of the liquid in SI units?

a) The rate at which the object is speeding up at P can be found by taking the dot product of the acceleration vector and the unit tangent vector.

(4,5) · Jo(-3,1) = 4*(-3) + 5*1 = -12+5 = -7 ft/s^2

The rate of change of speed at P is -7 ft/s^2.

b) The object's speed at P can be found using the formula for curvature and speed:

Speed = Curvature * radius

In this case, the curvature is 0.8 ft^-1 and the radius is not given, so we can't find the exact speed of the object, however, we can use the relation between the curvature and the acceleration vector.

Acceleration vector = curvature * Speed * Unit Tangent vector

√(4^2 + 5^2) = √(25+16) = √(41) = sqrt(41) = 6.4 ft/s

The object's speed at P is 6.4 ft/s.

To learn more problems on an object's speed:

https://brainly.com/question/29223620

#SPJ4

The magnitude of the electric field at the center of the square is 8.24 N/C.

The International System of Units uses the coulomb (C) as the basic unit of electric charge (SI).

It is the quantity of electrical energy that a 1-ampere (A) current can transport in a second (s). The electrical charge of around 6.24 x 1018 electrons or protons is equal to a quantity of 1 C.

The electric field at the center of the square due to the four charges at the corners will be the vector sum of the electric fields due to each of the charges. Since the charges are located at the corners of a square, the electric fields due to each charge will be oriented perpendicular to the line connecting the center of the square to the charge.

To calculate the magnitude of the electric field, we can use Coulomb's law:

E = k * (q / r^2)

Where k is Coulomb's constant, q is the charge, and r is the distance from the charge to the point where we are calculating the electric field.

The distance from the center of the square to each corner is (4.5 cm) / sqrt(2) = 3.225 cm.

E = 9 * 10^9 * ((3.3 * 10^-6) / (3.225 * 10^-2)^2)

E = 8.24 N/C

So, the magnitude of the electric field at the center of the square is 8.24 N/C.

To know more about coulomb, visit:

brainly.com/question/23942857

#SPJ4

The area of the parallelogram shrinks because the principle that allows a scissor lift to raise on top of it to a significant height can be demonstrated with four freezer pop sticks.

An explanation of a parallelogram

A quadrilateral with two sets of parallel sides is referred to as a parallelogram. In a parallelogram, the opposing sides are of equal length, and the opposing angles are of equal size. Additionally, the interior angles that are additional to the transversal on the same side.

Rhombus or parallelogram?

Angles on either side are equal. However, a rhombus is referred to as a square if all of its angles are 90 degrees. Additionally, every rhombus is regarded as a parallelogram, but the opposite is never true.

To know more about parallelogram visit:

https://brainly.com/question/12550364

#SPJ4

A  human-designed system  is computer. Four important of computer is:

Learn more about computer here:

https://brainly.com/question/21080395

#SPJ1

The projectile will rise to a height of 16 feet in 3 seconds, reach its highest point in 4.5 seconds, and then fall.

In physics and engineering, projectile motion has a wide range of applications. The movement of any ball in sports, fireworks, and meteors entering the Earth's atmosphere are a few examples. These objects are referred to as projectiles, and the course they follow is referred to as a trajectory.

Depending on the direction of the bullet's starting velocity, there are various forms of projectile motion. The three primary types are oblique projectile, horizontal projectile, and vertical projectile motion.

When  S = 16 feet, find  t  in seconds:

16 = 120t - 16t²

16t² - 120t + 16 = 0

Factor:

(8) (2t² - 15t + 27) = 0

Factor further  (2x² - 15x + 27):

(t - 3) (2t - 9) = 0

Equate each factor to 0:

t - 3 = 0

t = 3 seconds

2t - 9 = 0

2t = 9

t = 9/2 or 4.5 seconds

t = {3, 4.5

To know more about projectile visit:

https://brainly.com/question/11422992

#SPJ4

J/kg K is the most widely used unit in the SI system. 1 J/kg K is equal to 5.97994 ft lb/slug °R, and 1 ft lb/slug °R is equal to 0.167226 J/kg K.

A universal standard for expressing the magnitudes or quantities of significant natural events is the International System of Units. The acronym SI, which derives from the French term Système international d'unités, stands for the System of Units, also known as the metric system.

Starting with seven base units—the second (symbol s, the unit of time), metre (m, the unit of length), kilogram (kg, mass), ampere (A), electric current, kelvin (K, the thermodynamic temperature), mole (mol, the amount of substance), and candela (cd, the luminous intensity)—the SI consists of a coherent system of units of measurement.

To know more about SI system visit:

https://brainly.com/question/20877138

#SPJ4

The wavelength appear(s) in the atom's  Emission spectra: 303.2 nm, 706.5 nm and in Absorption spectra: 303.2 nm, 706.5 nm

The energy levels of an atom are determined by the number of electrons in the atom and the energy levels of the electron. In a simple atom, the allowed energies are 0.0 ev, 4.0 ev, and 6.0 ev. The emission spectrum of an atom is determined by the energy levels of the electrons and the energy levels of the atom.

When an electron in the atom jumps from a higher energy level to a lower energy level, it releases energy in the form of a photon. The wavelength of the photon can be calculated using the equation: wavelength = hc/energy.

For example, when an electron jumps from the 4.0 ev level to the 0.0 ev level, it releases a photon with a wavelength of 706.5 nm. When an electron jumps from the 6.0 ev level to the 4.0 ev level, it releases a photon with a wavelength of 303.2 nm.

The absorption spectrum of an atom is determined by the energy levels of the electrons and the energy levels of the atom. When an atom absorbs a photon, an electron jumps from a lower energy level to a higher energy level.

The wavelength of the photon that is absorbed can be calculated using the same equation as for the emission spectrum. In this case, the absorption spectra will be the same as the emission spectra.

For more questions like Spectra click the link below:

https://brainly.com/question/11736792

#SPJ4

The observations that led Bohr to formulate his model of the hydrogen atom is a low-density gas emits a series of sharp spectral lines. Thus, option A is correct.

An object's density is calculated by dividing its mass by the volume it occupies (volume). This provides a ratio of specific objects per unit volume of space.

The individual molecules in the gaseous state are more dispersed than they are in the liquid or solid phases, so there is less of the object for the same volume of space in the gaseous state than in the other phases.

Use what our old friend Archimedes noticed to your advantage. He found that when submerged in a fluid, a body experiences an upward force equal to the weight of the fluid it has displaced.

Learn more about low-density gas

https://brainly.com/question/12022043

#SPJ4

The magnitude of the charge on the ball is 0.44 μC.

option A is the correct answer.

The magnitude of the charge on the ball is calculated by applying Newton's second law of motion Coulomb's law as follows;

Mathematically, the formula for Newton's second law of motion and coulomb's law is given as;

F = mg

F = kq²/r²

where;

kq²/r² = mg

q² = ( mgr² ) / ( k )

q = √ ( mgr² / k )

The magnitude of the charge on the ball is calculated as follows;

q = √ ( 0.002 x 9.8 x 0.3² / 9 x 10⁹ )

q = 4.4 x 10⁻⁷ C

q = 0.44 x 10⁻⁶ C = 0.44 μC

Learn more about charge here: https://brainly.com/question/18102056

#SPJ1

Answer:

posetive

Explanation:

an object with a force exerted on it will move forwards

The internal energy of the triathlete change 680 J.

The process of converting energy from one form to another is called energy transformation or energy conversion. In physics, energy is a property that gives one the ability to move an object, lift it, or produce heat.

Conduction, radiation, and convection are the three different ways that thermal energy is transferred. Only fluids experience the cyclical process of convection. The total amount of energy in the universe has never changed and will never change because it cannot be created or destroyed.

1 cal = 4.184 J, thus 400 cal = 1673.6 J.

The change in internal energy is ΔU = ΔQ-ΔW

or ΔU = 1673.61000 673.6≈ 680 J

To learn more about energy change from given link

https://brainly.com/question/19666326

#SPJ4