Acceleration of a satellite refers to the rate of change of its velocity as it moves in its orbit. The acceleration of a satellite is caused by the gravitational force between the satellite and the planet it is orbiting.
What is acceleration of the satellite?When a satellite is in circular orbit, it experiences centripetal acceleration, which is provided by the gravitational attraction between the satellite and the Earth.
The acceleration of the satellite can be calculated using the following formula:
a = v^2/r
where a is the acceleration, v is the velocity of the satellite, and r is the radius of the circular orbit.
In this case, the height of the satellite above the Earth's surface is equal to the Earth's radius, so the radius of the circular orbit is:
r = height above the surface + Earth's radius
= 2 * Earth's radius
The velocity of the satellite can be calculated using the formula for the circular motion:
v = (G*M/r)^0.5
where G is the gravitational constant, M is the mass of the Earth, and r is the radius of the circular orbit.
Substituting the values, we get:
v = (GM/(2Earth's radius))^0.5
Now, we can calculate the acceleration:
a = v^2/r
= ((GM/(2Earth's radius))^0.5)^2/(2Earth's radius)
= GM/(4*Earth's radius)
Therefore, the acceleration of the satellite is directly proportional to the mass of the Earth and inversely proportional to four times the Earth's radius. The value of the acceleration is approximately 1.23 m/s^2.
To know more about acceleration of the satellite visit:
https://brainly.com/question/14218620
#SPJ4
If a 240 volt voltage source is connected to a wire with 10
ohms of resistance, what is the current?
If a 240 volt voltage source is connected to a wire with 10 ohms of resistance, then the current is 24 amp.
Given data as per the question is:
Voltage given - 240 V
Resistance = 10 ohm
The formula to be used in such numerical is,
V=IR --------------------- (A)
where V in the equation is the voltage, I in the equation is the current and R in the equation is the resistance.
Substituting the values in the equation (A)
240=I(10)
I= 240/10 = 24 amp
The current is 24 amp.
The formula V=IR is the ohm's law. The current which is flowing through the wire is directly proportional to the potential difference applied across its ends of it ,provided that the temperature and all the other physical conditions of the wire like stresses and strains remains absolutly constant.
Learn more about ohm's law:
brainly.com/question/1247379
#SPJ4
how to calculate the maximum height of a projectile given its original position and initial velocity only up and down
The maximum height of a projectile given its original position and initial velocity is, h = (v^2)/(2g).
Maximum height of a projectile given its original position and initial velocity in the vertical direction,
h = (v^2*sin^2(theta))/(2g)
where v is the initial velocity in the vertical direction, theta is the angle of the initial velocity and g is the acceleration due to gravity.
If the projectile is launched straight up, then theta = 90 degrees,
h = (v^2)/(2g)
To use this formula, you need to know the value of v, the initial velocity of the projectile in the vertical direction. This can be found by analyzing the initial conditions of the problem or by measuring the initial velocity directly.
To know more about the projectile, here
brainly.com/question/11422992
#SPJ4
oil droplets may gain electrical charges as they are projected through a nozzle. which quantity of charge is not possible on an oil droplet?
Electric charge is not possible on an oil droplet
How do charged oil drops form?
When radiation (such as X-rays) ionizes the area between the metal plates, electrons from the air attach to the falling oil droplets and give them a negative charge.
They could only gain or lose electrons, which are the only charged particles. The "elementary charge" of an electron is 1.60 • 10-19 C, and it is present on every electron. Therefore, any oil droplet's charge needs to be a multiple of this quantity. Due to their typically low conductivity, lubricants can act as insulators in transformers and switches. Oils can conduct electrical current, though. Their conductivity is influenced by a number of variables, including as the base oil, additives, and polarity.
To learn more about electrons use:
https://brainly.com/question/371590
#SPJ1
Which gas has the highest average kinetic energy?
Nitrogen and helium have the highest average kinetic energy because they are maintained at the highest temperature.
Kinetic energy is the energy possessed by molecules in motion. Average kinetic energy corresponds to the total kinetic energy of the molecules of a gas. Now, as temperature has a direct influence on the motion of the particles in a gas, it therefore, influences the average kinetic energy. Thus, nitrogen and helium, when at 100° C, have the highest average kinetic energy.
We can now say that hotter objects tend to have greater average kinetic energy and also the higher temperatures, and vice-versa. The average energy of the gas particles impacting the container walls grows as the temperature rises. The force the particles per unit area apply to the container is known as pressure. Pressure must increase as the temperature does.
To know more about average kinetic energy, refer:
https://brainly.com/question/29447155
#SPJ4
A. 36,000 Joules
B. 73,000 Joules
C. 146,000 Joules
D. 292,000 Joules
Option B is correct.
Kinetic energy is the energy that a body possesses as a result of its movement. Potential energy is the energy that a body possesses as a result of its location or state.
While an object's kinetic energy is relevant to the state of other items in its environment, potential energy is fully independent of its surroundings. As a result, the acceleration of an item is not visible in the movement of a single object when other objects in the same environment are also moving.
Here potential energy is being used so work done will be mgh
Where,
M = mass
G = acceleration due to gravity
H = height
Since there is no change in kinetic energy,
So,
W1/W2 = mgh1/mgh2
Now, here mass and acceleration due to gravity are the same
Therefore,
W1/W2 = h1/h2
W2 = 0.5 × 146000J = 73000J
Therefore, the work done to lift the block halfway to the top is 73,000 joules.
To learn more about Potential energy:
https://brainly.com/question/23979653
Two friends are playing with a toy telephone. Which of the points P,Q and R will vibrate if one of the friends speak into the cup? Justify your answer
The point that will vibrate the most when one of the friends speaks into the cup is point Q as vibration dampens and energy is lost due to friction.
In a toy telephone, sound is transmitted through a string that connects two plastic cups. When one person speaks into one cup, the sound waves vibrate the cup, which in turn vibrates the string and causes the other cup to vibrate as well.
Assuming that the string is held taut, the vibration of the cups will depend on the placement of the points P, Q, and R, as shown in the figure. If the string is not taut, the cups may not vibrate at all, or the vibrations may be too weak to transmit the sound effectively.
Point P is located at the midpoint of the string, and it will not vibrate much because the two cups are attached to it and there is no space for it to move.
Point Q is located at one end of the string, and it will vibrate the most when one of the friends speaks into the cup. This is because the cup will vibrate the string, and the vibration will be transmitted all the way to the other end of the string, where point Q is located.
Point R is located between P and Q, and it will vibrate to some extent, but not as much as point Q. This is because the vibration will be damped as it travels along the string, and some of the energy will be lost due to friction.
Learn more about vibrate here:
https://brainly.com/question/30245263
#SPJ4
it takes 10 million (1x107) hudfs to fill the entire sky. using this information and your answer from the previous part, how many stars are there in the observable universe? express your answer using scientific notation.
The estimated number of stars in the observable universe is about 1x10^22.
Scientific Notation10 million can be written as 1,000,000,000 . It is expressed in scientific notation, it becomes 10 raised to 9= 1,000,000,000
What is an Universe?The universe is made up of all of space, time, and everything that exists within them, including all of the planets, stars, galaxies, and other types of matter and energy. The prevailing cosmological explanation for the universe's formation is the Big Bang theory. The universe has been expanding ever since the Big Bang, which occurred 13.7870.020 billion years ago, according to this theory. Although the size of the entire universe's space is unknown, the observable universe's diameter, which is about 93 billion light-years at the moment, can be calculated.
Learn more about Big Bang Theory here:
brainly.in/question/4921972
#SPJ1
The estimated number of stars in the observable universe is about 1x10^22.
Scientific Notation
10 million can be written as 1,000,000,000 . It is expressed in scientific notation, it becomes 10 raised to 9= 1,000,000,000
What is an Universe?
The universe is made up of all of space, time, and everything that exists within them, including all of the planets, stars, galaxies, and other types of matter and energy. The prevailing cosmological explanation for the universe's formation is the Big Bang theory. The universe has been expanding ever since the Big Bang, which occurred 13.7870.020 billion years ago, according to this theory. Although the size of the entire universe's space is unknown, the observable universe's diameter, which is about 93 billion light-years at the moment, can be calculated.
Learn more about Big Bang Theory here:
https://brainly.com/question/17209127
#SPJ1
in the book example concerning the figure above, a force of 0.086 n from an external agent was required to keep the rod moving at a constant speed. suppose the light bulb in the figure is unscrewed from its socket. how much force would now be needed to keep the rod moving at a constant speed? justify your answer.
The correct answer is 0 N.
There will be no current in the rod and thus no magnetic force resisting the motion. Without any resistance, it will keep moving until acted on by an outside force according to Newton's first law.
What is motion?
Numerous physical systems, including objects, bodies, matter particles, matter fields, radiation, radiation fields, and radiation particles, as well as curvature and space-time, are affected by motion. One can also talk about how borders, shapes, and pictures move. A physical system's configuration or locations continuously changing in space is what is often meant by the term "motion." For instance, one can discuss the motion of a wave or a quantum particle, where the configuration is made up of the probabilities that the wave or particle would occupy particular places.To know more about motion, click the link given below:
https://brainly.com/question/22810476
#SPJ1
in which scenario is the change in momentum greatest? coming to a stop by landing on the trampoline. coming to a stop by landing on the ground. the change in momentum is the same for both scenarios.
The change in momentum is greatest when coming to a stop by landing on the ground.
This is because when a person comes to a stop on the ground, the time of impact is shorter than when they come to a stop on a trampoline. Since the force is the rate of change of momentum, a shorter time of impact results in a greater force acting on the body, which leads to a larger change in momentum.
In contrast, when a person lands on a trampoline, the surface is more yielding and will absorb some of the force of impact over a longer time, resulting in a smaller force acting on the body and a smaller change in momentum.
For more such questions on Momentum
https://brainly.com/question/1042017
#SPJ4
The Density Of Mercury Is 13600 Kg/M3 At 0 OC. What Would Its Density Be At 166 OC? Coefficient Of Volume Expansion For Mercury Is 182x10-6(O C)The density of mercury is 13600 kg/m3 at 0 oC.What would its density be at 166 oC?Coefficient of volume expansion for mercury is 182x10-6(o C)
The density of mercury at 166 °C would be approximately 13203 kg/m³.
What is the density of a substance?A substance's density is a physical characteristic that indicates how much mass there is per unit volume. In other terms, it is a measurement of how close together a substance's particles are packed. The density equation is:
Mass / Volume equals density.
Where an object's volume is the amount of space it takes up and its mass is the amount of substance it contains.
Depending on the measurement system being used, the units for density may vary. The unit of density in the International System of Units (SI) is kilograms per cubic meter (kg/m3). However, additional measurements can also be made, such as grams per cubic centimeter (g/cm3) or pounds per cubic foot (lb/ft3).
To calculate the density of mercury at 166 °C, we can use the following formula:
ρ2 = ρ1 / [1 + β (T2 - T1)]
where:
ρ1 = 13600 kg/m³ is the density of mercury at 0 °C
β = 182 x 10^-6/°C is the coefficient of volume expansion for mercury
T1 = 0 °C is the initial temperature
T2 = 166 °C is the final temperature
Substituting these values into the formula, we get:
ρ2 = 13600 kg/m³ / [1 + (182 x 10^-6/°C) x (166 °C - 0 °C)]
ρ2 = 13600 kg/m³ / [1 + (182 x 10^-6/°C) x (166 °C)]
ρ2 = 13600 kg/m³ / 1.030012
ρ2 = 13203 kg/m³
Therefore, the density of mercury at 166 °C would be approximately 13203 kg/m³.
To know more about density, visit:
https://brainly.com/question/1354972
#SPJ4
what is the advantage of the larger diameter of jwst? choose one or more: a. at a particular wavelength, the resolution for the jwst is 2.7 times better than that for hst. b. the light-gathering ability of the jwst is 7.3 times better than it is for the hst. c. the light-gathering ability of the hst is 2.7 times better than it is for the jwst. d. at a particular wavelength, the resolution for the jwst is 7.3 times better than that for hst. e. the light-gathering ability of the hst is 7.3 times better than it is for the jwst. f. the light-gathering ability of the jwst is 2.7 times better than it is for the hst.
The advantage of the larger diameter of JWST is the light gathering ability of the JWST is 7.3 times better than it is for the HST. Hence, the correct option is (b).
The advantage of the larger diameter of the James Webb Space Telescope (JWST) over the Hubble Space Telescope (HST) is that the light gathering ability of the JWST is 7.3 times better than that of the HST. This is because the diameter of the JWST's primary mirror is 6.5 meters, while the diameter of the HST's primary mirror is only 2.4 meters. The greater the diameter of a telescope's mirror, the more light it can collect and focus, which leads to better image resolution and sensitivity.
Option (a) is incorrect, because a better light-gathering ability does not necessarily translate to a better resolution. The resolution of a telescope depends on a number of factors, including its optics, the size of its detector, and the amount of light that it can gather.
And options (c), (d), (e), and (f) are also incorrect, as the light-gathering ability of the JWST is 7.3 times better than that of the HST, not 2.7 times.
To know more about light please refer: https://brainly.com/question/1391842
#SPJ4
the temperature of the filament of an incandescent lightbulb is 2800 k. treating the filament as a blackbody, determine the fraction of the radiant energy emitted by the filament that falls in the visible range. also, determine the wavelength at which the emission of radiation from the filament peaks
The peak wavelength of radiation from a 2800 K incandescent bulb is 1.035 μm, outside the visible range. Most energy is infrared.
The fraction of the radiant energy emitted by the filament that falls in the visible range can be calculated using Wien's displacement law and the Stefan-Boltzmann law.
Wien's displacement law states that the peak wavelength of the radiation emitted by a blackbody is inversely proportional to its temperature. The formula is:
peak wavelength = constant / temperature
where the constant is approximately equal to 2.898 × [tex]10^(-3)[/tex] meters-kelvin.
Substituting the temperature of the filament (2800 K) into the formula, we get:
peak wavelength = 2.898 × [tex]10^(-3)[/tex]m-K / 2800 K = 1.035 × [tex]10^(-6)[/tex] meters
This means that the peak wavelength of the radiation emitted by the filament is in the infrared range, and is not visible to the human eye.
The fraction of the radiant energy emitted by the filament that falls in the visible range can be approximated by integrating the Planck radiation law over the visible spectrum (approximately 400-700 nm) and dividing by the total radiant energy emitted by the filament. The formula for the radiant flux density emitted by a blackbody is:
radiant flux density = σ[tex]T^4[/tex]
where σ is the Stefan-Boltzmann constant ([tex]5.67 *10^(-8) W/m^2-K^4[/tex]) and T is the temperature of the filament in kelvin.
Integrating this formula over the visible spectrum, we get:
radiant flux in visible range = ∫(400 nm to 700 nm) [2πh[tex]c^2 / λ^5[/tex]] / [exp(hc/λkT) - 1] dλ
where h is Planck's constant, c is the speed of light, and k is the Boltzmann constant.
Evaluating this integral gives the radiant flux in the visible range. Dividing this by the total radiant flux emitted by the filament (which is just σ[tex]T^4[/tex]), we can find the fraction of the radiant energy emitted by the filament that falls in the visible range. This calculation is quite involved, and would require numerical integration, but in general, only a small fraction of the energy emitted by a filament at 2800 K falls in the visible range. Most of the energy is emitted in the infrared and ultraviolet ranges.
To learn more about radiant energy, refer:
https://brainly.com/question/13942337
#SPJ4
a close inspection of an electric circuit reveals that a 480 ohm resistor was inadvertrently soldered in the place where a 350 ohm resistor is needed. how can this be fixed without removing anything from the exsiting circuit?
A resistance of 140 ohm is needed to be added in parallel connection with 480 ohm resistor to fix the existing circuit.
It was revealed in the close inspection of an electric circuit that a 480 ohm resistors was inadvertently soldered in the place where 350 ohm resistor was needed.
Now because the 480 ohm resistor cannot be removed we have to fix the existing circuit by adding an another resistance in parallel with the 480 ohm resistance to make it equal to 350 ohm.
So, we write, let us say we added R in parallel,
1/350 = 1/R + 1/480
R = 1400ohm.
So, we need to add a 1400 ohm resistor in the existing circuit.
To know more about resistance, visit,
https://brainly.com/question/17563681
#SPJ4
A 5 kg box is attached to a spring that has an elastic coefficient of 110 N/m. The spring is compressed to a distance of 0. 65 meters. What is the velocity of the box after it is released from the spring?
The required velocity of the box after it is released from the spring is 5.35 m/s.
The mass of the box m is given as 5 kg.
Elastic coefficient k is given as 110 N/m.
Compression of the spring x is given as 0.65 m.
We know the expression for force as,
F = k x
where,
k is the elastic coefficient
x is the compression in spring
Entering the values we have,
F = k x = 110 × 0.65 = 71.5 N ----(1)
Force is nothing but the tension in the spring which is given by the expression,
F = T = 1/2 m v² = 1/2 (5)v² = 2.5 v² ----(2)
Equating (2) and (1), we have,
2.5 v² = 71.5
v² = 28.6
v = 5.35 m/s
Thus, the velocity of the box after it is released from the spring is 5.35 m/s.
To know more about springs:
https://brainly.com/question/18833644
#SPJ4
In which state of matter, do the particles have the maximum energy?
A
Solid
B
Liquid
C
Gas
D
None of these
a solid ok thank you
hope it helps
the earth has a much larger mass than the moon. how many moons would it take to equal the mass of earth?
Answer: 81 1/2 moons would be needed to equal the amount of mass of Earth
Explanation:
what forces work on the mass in the new coordinate system? suppose the mass is a height y in the new coordinates. the total force on it is given: ftot
The forces acting on a mass in a coordinate system include gravitational forces, electromagnetic forces, frictional forces, and tension forces.
The equations you provided are the equations of motion for a particle with mass m moving in a straight line under the influence of a net force Ftot. The equation Ftot = md²r/dt² represents Newton's Second Law of Motion, which states that the net force acting on an object is equal to its mass times its acceleration.
The second equation, r = (d²r/dt²)t², gives the position of the particle as a function of time. It is the second derivative of the position vector r with respect to time t, which corresponds to the acceleration of the particle.
Together, these equations describe the motion of a particle under the influence of a net force and can be used to calculate the position, velocity, and acceleration of the particle as a function of time.
Learn more about the force at
https://brainly.com/question/13191643
#SPJ4
The question is -
What forces work on the mass in the new coordinate system? suppose the mass is a height y in the new coordinates. the total force on it is given: [tex]F_{tot}[/tex] = md²r/dt²
The robot arm is elevating and extending simultaneously. At a given instant. theta = 30 degree, theta with dot = 10 deg/s = constant, l = 0.5 m, i = 0.2 m/s, and l with dieresis = -0.3 m/s2. Compute: express v right words arrow and a right words arrow in terms of unit vectors I with Hat and j with Hat. the magnitudes of the velocity v and acceleration a of the gripped part P.
The velocity of the gripped part P is -0.4i_hat + 0.293j_hat m/s, and the acceleration is -0.05i_hat - 3.93j_hat m/s^2. The magnitude of the velocity is 0.5 m/s, and the magnitude of the acceleration is 3.93 m/s^2.
What is tangential acceleration?Tangential acceleration is the component of acceleration that is parallel to the instantaneous velocity of an object moving along a curved path. It represents the rate of change of the magnitude of the velocity vector of the object. Mathematically, the tangential acceleration at any instant is given by the formula:
a_t = r * d²(theta)/dt²
To compute the velocity and acceleration of the gripped part P, we can use the equations for velocity and acceleration of a particle in planar motion:
v = v_i + a_t, where v_i is the initial velocity and a_t is the tangential acceleration a = a_t + a_n, where a_n is the normal acceleration
First, let's find the position of the gripped part P at the given instant. We can use the law of cosines to find the length of the arm:
l² = i² + 2ilcos(theta) + l² cos(theta) = (l² + i² - l²)/(2il) = (i²)/(2il) = 0.2/(20.5) = 0.2
Therefore, theta = arccos(0.2) = 78.46 degrees.
Next, let's find the position vectors of the gripped part P at the given instant. We can use the polar coordinates of P:
r = l theta = theta x = rcos(theta) = 0.5cos(78.46) = 0.13 m y = rsin(theta) = 0.5sin(78.46) = 0.47 m
Now, let's find the velocity vector v. We can find the tangential acceleration using the formula:
a_t = ld^2(theta)/dt^2 = l(-0.3)*cos(theta) = -0.15 m/s^2
Therefore, the velocity vector is:
v = v_i + a_t = ltheta_dot(-sin(theta)*i_hat + cos(theta)j_hat) + (-0.15(-sin(theta)*i_hat + cos(theta)j_hat)) = (-0.25(-sin(30)*i_hat + cos(30)j_hat)) + (-0.15(-sin(30)i_hat + cos(30)j_hat)) = (-0.4i_hat + 0.293j_hat) m/s
The magnitude of the velocity is:
|v| = sqrt((-0.4)^2 + (0.293)^2) = 0.5 m/s
Next, let's find the acceleration vector a. We can find the normal acceleration using the formula:
a_n = l × (d^2(theta)/dt^2)sin(theta) = -0.30.5×sin(78.46) = -0.145 m/s^2
Therefore, the acceleration vector is:
a = a_t + a_n = (-0.15*(-sin(30)*i_hat + cos(30)j_hat)) + (-0.145sin(78.46)*cos(30)i_hat + (-0.145sin(78.46)sin(30) - 9.81)j_hat) = (-0.05i_hat - 3.93j_hat) m/s²
The magnitude of the acceleration is:
|a| = √((-0.05)² + (-3.93)²) = 3.93 m/s²
To know more about acceleration, visit:
https://brainly.com/question/12550364
#SPJ1
an airplane flies from joint base lewis mcchord (jblm) to a undisclosed location 80 km south and 200 km east. in what direction should the plane fly?
Greetings from Joint Base Lewis-McChord, the base where I Corps and the 62 Airlift Wing are based. The flagship military facility on the West Coast for the Department of Defence is Joint Base Lewis-McChord, which is situated in the Puget Sound area of the Pacific Northwest.
What is the joint base lewis mcchord (jblm)?JBLM, the sole Army Power Projection Platform west of the Rocky Mountains, has since expanded to become the largest Army-led joint post in the United States.
Because of the 100 km/h speed, the net spirit of the plane will be in this activity. In order to determine the plane's motion with respect to the north, we first locate the theatre.
The calculation would be 100 km/h divided by 300 km/h. According to the formula, three would win 10 thetas.
Therefore, The plane's motion's angle determines whether it is respectable.
Learn more about joint base here:
https://brainly.com/question/28923086
SPJ1
The full range of frequencies of electromagnetic radiation is called
A. Visible light
B. Radio waves
C. The electromagnetic spectrum
D. Invisible radiation
The full range of frequencies of electromagnetic radiation is called the electromagnetic spectrum. So, the correct answer is C.
The electromagnetic spectrum includes all types of electromagnetic radiation, including visible light, radio waves, microwaves, infrared radiation, ultraviolet radiation, X-rays, and gamma rays. Each type of electromagnetic radiation has a different frequency and wavelength, and they all travel at the speed of light in a vacuum. Each type of electromagnetic radiation has a unique wavelength and frequency, which determine its properties and the way it interacts with matter. Radio waves have the longest wavelength and the lowest frequency in the electromagnetic spectrum, followed by microwaves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays.
Learn more about the electromagnetic spectrum: https://brainly.com/question/2261239
#SPJ11
Your boss has assigned you the task to make a ball appear red. You have the following available to accomplish the task:
• a ball that appears white in white light that can be turned either ON or OFF
.
.
red, green, and blue lights.
cyan, magenta, and yellow filters
Describe at least three ways that you can make the ball look red.
Here are three ways to make the ball look red:
Use a red light: Shine a red light directly onto the white ball while the ball is in the ON position. This will cause the ball to reflect only the red light and appear red.
What of the other response?In regards to the Use a magenta filter: Shine a white light onto the white ball while the ball is in the ON position, and place a magenta filter in front of the light source. This will cause the ball to reflect both red and blue light, which will combine to create the appearance of red.
Lastly, Combine green and blue light with a yellow filter: Shine a white light onto the white ball while the ball is in the ON position, and use green and blue lights to illuminate the ball. Place a yellow filter in front of the ball, which will absorb the green and blue light and allow only red light to pass through. This will create the appearance of a red ball.
Learn more about color from
https://brainly.com/question/4431200
#SPJ1
What is the specific heat of a 3. 78 kg object that absorbs 678 J as the temperature increases by 4. 25 K?
The specific heat of a 3. 78 kg object that absorbs 678 J is 42.2 J/(kg-K).
As per the given information in the question:
Specific heat = 3.78 kg
Absorption of the object = 678 J
Temperature increase = 4.25 K
Specific heat has units of J / (kg C).
Substituting the values in the formula,
Specific Heat = 678 / 3.78 kg * 4.25 C) = 42.2 J/(kg-K)
The specific heat is defined as the amount required to raise the temperature of a unit mass of a substance by 1 degree Celsius.
This is expressed mathematically as
Q= mc∆T
Learn more about specific heat:
brainly.com/question/11297584
#SPJ4
What is the mass defect of lithium? Assume the following: Atomic number of lithium = 3 Atomic mass of lithium = 7. 0144 atomic mass units. Mass of 1 proton = 1. 0073 atomic mass units. Mass of 1 neutron = 1. 0087 atomic mass units.
(A)0. 0043 atomic mass units
(B)0. 0423 atomic mass units
(C)3. 0219 atomic mass units
(D)4. 0348 atomic mass units
(E)7. 0567 atomic mass units
The mass of an atom is less than the sum of the masses of its component protons, neutrons and electrons. The mass defect is 0.0423 amu. The correct option is B.
What is mass defect?The mass defect is equal to the mass lost as an equivalent amount of energy during the formation of a given nucleus from the component nucleons.
Δm = M°- M
Δm = Mass defect
M° = Expected total mass
M = Experimentally determined mass
Here 'Li' has 3 protons and 4 neutrons.
The mass of proton = 3 × 1.0073 = 3.0219 amu
The mass of neutron = 4 × 1.0087 = 4.0348 amu
The sum of masses of protons and neutrons = 7.0567
Mass defect = 7.0567 - 7.0144 = 0.0423 amu
Thus the correct option is B.
To know more about mass defect, visit;
https://brainly.com/question/16485729
#SPJ1
An ecologist recorded 12 white-tailed deer, Odocoileus virginianus, per square kilometer in one woodlot and 20 per square kilometer in another woodlot. What was the ecologist comparing?
A) Density
B) Range
C) Cohorts
D) Dispersion
E) Carrying capacity
The ecologist was comparing the density of white-tailed deer, Odocoileus virginianus, between two woodlots.
What is Density?A population's density is calculated as the number of people in a given area or volume. It is a key parameter for comprehending the dynamics of populations and one of the most fundamental ideas in population ecology.
The number of people per unit area, such as per square meter or per square kilometer, is a common way to represent population density in the context of ecology. As an illustration, it is possible to compute the density of a certain species in a particular habitat by counting the number of individuals inside a given area and dividing that number by the area.
The dynamics of the population are significantly influenced by density. Increased resource competition brought on by a high population density may have an impact on population growth, survival, and reproduction. A low population density, on the other hand, may lead to less competition for resources and more food availability, which may encourage human growth and reproduction.
To know more about Density visit:
https://brainly.com/question/29775886
#SPJ4
A ball of mass 0.5 kg is thrown with kinetic energy of 100 J vertically upward. If air resistance is neglected, find maximum height reached by the ball. (g = 10 m/s²)
Answer:
20 meters
Explanation:
The initial velocity of the ball can be determined using the equation for kinetic energy:
K = (1/2)mv^2
100 J = (1/2) * 0.5 kg * v^2
So, v^2 = 200 J / 0.5 kg = 400 m^2/s^2
The velocity can be determined from the square root:
v = sqrt(400 m^2/s^2) = 20 m/s
Now we can use the velocity to determine the maximum height. The maximum height is reached when the velocity is zero, so we can use the formula for vertical motion under constant acceleration to find the time when this occurs:
v = v0 - gt
0 = 20 m/s - 10 m/s^2 * t
t = 2 s
We can use this time to find the maximum height:
h = v0 * t - (1/2)gt^2
h = 20 m/s * 2 s - (1/2) * 10 m/s^2 * 2 s^2
h = 40 m - 20 m
h = 20 m
So, the maximum height reached by the ball is 20 meters.
who described the universe as a giant clock with unified rules for gravity and motion?
Isaac Newton described the idea that the universe as a giant clock with unified rules for gravity and motion.
The clockwork universe is commonly stated with Sir Isaac Newton but it turns out that both he and his close philosophical supporter Samuel Clarke both strongly criticized the notion of the clockwork universe, because it left no room for Divine Providence.
The faster a clock moves, the slower time passes according to someone in a different frame of reference.
In the history of science, the clockwork universe compares the universe to a mechanical clock. It continues ticking along, as a perfect machine, with its gears governed by the laws of physics, making every aspect of the machine predictable.
Learn more about newton here:-
brainly.com/question/4128948
#SPJ4
the ________ is perhaps the most dramatic force now shaping our world.
The technology is perhaps the most dramatic force now shaping our world.
The rapid pace of technological advancement, driven by the emergence of new technologies such as artificial intelligence, machine learning, big data, and the internet, is arguably the most dramatic force shaping our world. This digital revolution has transformed the way we live, work, and communicate with one another, ushering in a new era of unprecedented connectivity and information exchange. With the rise of e-commerce and online marketplaces, the digital revolution has also brought about a significant shift in global economic power, as more and more businesses move to the online sphere. The digital revolution has also transformed our societies and political systems, as social media has become a powerful tool for activism and political mobilization.To know more about forces visit:
https://brainly.com/question/29044739
#SPJ1
which person below developed a system for predicting planetary positions that remained in use for some 1500 years?
Ptolemy. Ptolemy was a Greek astronomer who developed the Ptolemaic system of astronomy.
What is astronomer?Astronomer is an individual who studies the universe and its components such as stars, planets, galaxies, and other celestial bodies. They use observational data, mathematical models, and theoretical principles to understand the physical properties, evolution and origin of the universe. Astronomers often work in teams, and employ a variety of techniques to observe and analyze the data they collect. Astronomers may use ground-based telescopes, spacecraft, or other instruments to observe the universe and the objects within it.
This system used a combination of observational data and mathematical calculations to accurately predict the positions of the planets. This system was used for around 1500 years, until the invention of the telescope in the 17th century.
To learn more about astronomer
https://brainly.com/question/1003405
#SPJ1
I put a velocity of 5m/s up on a 2kg mass on a spring with a k value of 150N/m. What is the PE of the spring at the maximum, and what is the amplitude? What is the T?
The PE of the spring at the maximum is [tex]375J[/tex] and Temperature T is [tex]0.907s[/tex]
The potential energy of the spring at the maximum is the elastic potential energy. This is equal to the work done on the spring (the product of force and displacement) and is given by the equation:
[tex]PE =\frac{ 1}{2}kx^2[/tex], where k is the spring constant, and x is the displacement.
In this case, the displacement is equal to the amplitude of the spring, given by the equation:
[tex]A = (\frac{v^{2}}{k})^{1/2}[/tex], where v is the velocity.
Substituting this into the equation for PE, we get:
[tex]PE =\frac{ 1}{2}k(\frac{v^{2}}{k})^{2 }\\\\=\frac{ 1}{2}kv^{2}[/tex]
Plugging in the values for k and v given in the question, we get [tex]PE = \frac{1}{2}*150N/m*(5m/s)^2\\ \\PE= 375J.[/tex]
The equation provides the spring's duration:
[tex]T = 2\pi (m/k)^{1/2}[/tex]
where m is the mass of the object.
Substituting the values for m and k given in the question, we get:
[tex]T = 2\pi(\frac{2kg}{150N/m})^{1/2}\\\\ T= 0.907s.[/tex]
learn more about potential energy Refer:brainly.com/question/24284560
#SPJ4
a plane flies 72 x 105 m north and then another 15 x 105 m west in a total time of 6 h. the magnitude of your average velocity for the entire trip is
A plane flies 72 x 105 m north and then another 15 x 105 m west in a total time of 6 h. the magnitude of your average velocity for the entire trip is 340 m/s.
Displacement = [(72 x 10⁵]² + [15 x 10⁵]²
= 10⁵ x √72² + 15²
= 10⁵ x √5.409
= 73.545 x 10⁵
Time = 6 hours = 6 x 3600 sec
Velocity = 73.545x10⁵/36x6x100
V= 0.34044 x 10³
V = 340.49
V = 340 m/s
Magnitude of average velocity is 340 m/s.
The terms haste and speed give us an idea of how fast or decelerate an object is moving. relatively frequently, we come across situations where we need to identify which of the two or further objects is moving briskly. One can fluently tell the faster of the two if they're moving in the same direction on the same road. still, if their direction of stir is in the contrary direction, also it's delicate to determine the fastest.
In similar cases, the conception of haste is helpful. In this composition, let us learn the haste meaning, the unit of haste, the illustration of haste, and the difference between speed and haste.
Learn more about Average velocity:
https://brainly.com/question/29483294
#SPJ4
