all of the following can cause total bus failure of the j1850 vpwm bus system, except: (1pts) question 10 - all of the following can cause total bus failure of the j1850 vpwm bus system, except: open bus wire to the bcm. bus wire shorted to ground. bus wire shorted to battery voltage. internal short in a module.

Answers

Answer 1

Internal short in a module, bus wire shorted to battery voltage, and bus wire shorted to ground failure is reason of the j1850 vpwm bus system .

What are the different types of bus systems?

Data bus, Address bus, and Control bus are the three different categories of bus lines. Each bus route works together to communicate with the others over it. The data bus is a signal line used to transfer data from the CPU to the memory.

How does the system bus function?

A system bus functions by transferring data and other types of information among various hardware components of the computer. The system bus, for instance, will identify data when you attach a universal serial bus (USB) device or port into your computer and transfer it to the central processor unit.

To know more about vpwm bus system visit :-

https://brainly.com/question/13896970

#SPJ4


Related Questions

determine the volume in ft3,of 2lb of a two-phase liquid-vapor mixture of regrigerant 134a at 40f with a quality fo 20%. what is the pressure in lbf/in2\

Answers

Pressure is measured in PSI, which is equal to the amount of force (lbf) that is applied per unit of area (in2).

This is demonstrated by the equations below. Simply multiplying the pressure by the area over which the force is exerted will convert PSI to pounds. In various system of measurement, such as English engineering units and British gravitational units, a pound-force (lb, lbf) is a unit of force. It has the same force as one pound of mass does in a typical gravitational field. A unit of pressure or stress based on avoirdupois measurements is the pound per square inch, or more precisely, the pound-force per square inch (symbol: lbf/in2; abbreviation: psi). It is the pressure that results from applying one pound of force.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

Which of the following commands can be used to remove a group from a Linux system? (Choose all that apply.) a. rmgroup b. rmg c. groupdel d. delgroup

Answers

a. rmgroup and c. groupdel. rmgroup is a command used to remove a group from a Linux system. The command removes the specified group from the system, as well as any users that belong to the group.

What is system?

System is a set of interrelated components working together to achieve a common goal. It is a cohesive conglomeration of various components, which interact with each other to form a complex whole. A system can be defined as a group of elements that cooperate and interact with each other in a coordinated manner to achieve a specific purpose.

groupdel is a command used to delete a group from the system. The command deletes the specified group and any users that belong to the group.

To learn more about system
https://brainly.com/question/28717367
#SPJ4

python list of even integers in this challenge you are required to implement a function, that 1 is named even 2 takes 2 integer arguments

Answers

If an python list integer is even, its leftover after division by two must be 0. In mathematics, x is deemed to be even if x% 2 == 0. It takes this method O(N) time, where N is the size of the range.

How can I print how many even numbers there are in a list in Python?

By a single print. Print(0,2,4,6,8,10) For loop is the easiest approach. My first thought is: for I in range (0,11,2): For and% for I in range (11).

How do you find odd and even numbers in a list in Python?

Below is a list of the necessary code. Number = int (input "Enter any number to see if it's odd or even: " if (num% 2) == 0: print Input any number to determine whether it is odd or even. 887 887 is strange.

To know more about python list integer visit :-

https://brainly.com/question/15872044

#SPJ4

Create a static method that: is called remove All • returns nothing • takes two parameters: an ArrayList of Strings called wordList, and a String called targetWord This method should go through every element of wordList and remove every instance of targetWord from the ArrayList. Create a static method that: • is called appendPossum • returns an ArrayList • takes one parameter: an ArrayList of Integers . This method should: Create a new ArrayList of Integers Add only the positive Integers to the new ArrayList • Sum the positive Integers in the new ArrayList and add the Sum as the last element For example, if the incoming ArrayList contains the Integers (4.-6,3,-8,0,4.3), the ArrayList that gets returned should be (4.3,4,3,14), with 14 being the sum of (4.3,4,3). The original ArrayList should remain unchanged.

Answers

The answer provided below has been developed in a clear step by step manner.

Answer:

#include "linked_list.h"

#include <iostream>

using namespace std;

Linked_List::Linked_List(){

 length = 0;

 head = nullptr;

}

int Linked_List::get_length(){

 return this->length;

}

unsigned int Linked_List::push_front(int new_val){

 length ++;

 Node *new_node = new Node(new_val, head);

 head = new_node;

 return length;

}

unsigned int Linked_List::push_back(int new_val){

 length ++;

 if (head == nullptr){ //if it's empty

   head = new Node(new_val, nullptr);

 }

 else{

   Node *temp = this-> head; //start from head

   while (temp->next != nullptr){

     temp = temp->next; //scrolling till the very end

   }

   

   //inserting it at the end:

   Node *new_node = new Node(new_val, temp->next);

   temp-> next = new_node;

 }

 return length;

}

unsigned int Linked_List::insert(int new_val, unsigned int index){

 length++;

 

  Node *temp = new Node(new_val, NULL);

  if (index == 0){

    temp->next = this->head;

    head = temp;

    return length;

  }

 else{

 temp = this-> head;

 //temp -> val = new_val;

 int check = index-1;

  for (int i = 0; i< check; i++){

    temp = temp->next;

  }

 

 Node *new_node = new Node(new_val, temp->next);

 temp-> next = new_node;

 }

 return length;

}

void Linked_List::print(){

 Node *temp = this->head;

 while (temp != nullptr){

   cout << temp->val << "  ";

   temp = temp->next;

 }

 cout << endl;

}

void Linked_List::clear(){

 delete head;

}

void Linked_List::delete_all_nodes(){

   length = 0;

   Node* next = nullptr;

   Node* temp = head;

   while (temp != nullptr){

       next = temp->next;

       free(temp);

       temp = next;

   }

  head = nullptr;

}

Linked_List::Linked_List(const Linked_List& old_list){

 cout << "Invoked the copy constructor!" << endl;

 this-> length = old_list.length;

 this-> head = nullptr;

 Node *temp = old_list.head;

 

 while(temp != nullptr){

     Node *test = new Node(temp->val, temp->next);

     

     if (this->head == nullptr){

       this->head = test;

     }

       temp = temp->next;

     }

}

Linked_List& Linked_List::operator=(const Linked_List& old_list){

 cout << "Invoked the overloaded assignment operator" << endl;

 this-> length = old_list.length;

 this-> head = nullptr;

 Node *temp = old_list.head;

 

 while(temp != nullptr){

     Node *test = new Node(temp->val, temp->next);

     if (this->head == nullptr){

       this->head = test;

     }

       temp = temp->next;

     }

 return *this;

}

void Linked_List::check_for_prime(){

 int counter = 0;

 bool flag = true;

 Node *temp = this->head;

 

 while (temp != nullptr){

    // this assignment requires that a negative number is never considered to be prime. 0 and 1 are also not considered as prime numbers

   if (temp->val > 1){

     for (int i = 2; i <= temp->val/2; i++){

         if (temp->val % i == 0){ // here we check if there is such number that fully divides our value

         flag = false;    

         break;

         }

       }

     if (flag == true){

       counter++;

       }

     else{ flag = true; }

     }

   temp = temp->next;

 }

 cout << "You have " << counter << " prime number(s) in your list. (that's the total number of prime numbers) " << endl;

}

/*

merge_sort(head){

 1) check if length <= 1 if so return

 2) split unsorted list in half

 3) first = merge_sort(first half)

 4) second = merge_sort(second half)

 5) merge(first, second)

}

*/

Node* merge_sort(Node* head){

 Node *temp = head;

 int length = 0;

 

 while (temp != nullptr){

   temp = temp -> next;

   length ++;

 }

 if (length <= 1){

   return head;

 }

 temp = head;

 for (int i = 0; i< ((length-1)/2); i++){

    temp = temp -> next;

 }

 Node *second = temp-> next;

 temp-> next = NULL;

 temp = head;

 head = merge_sort(head);

 second = merge_sort(second);

 return merge(head, second);

}

Node* merge(Node* first, Node* second){

   Node* result = nullptr;

   if (first == nullptr){

       return second;

   }

   else if (second == nullptr){

       return first;

   }

   if (first->val <= second->val) {

       result = first;

       result->next = merge(first->next, second);

   }

   else{

       result = second;

       result->next = merge(first, second->next);

   }

   return result;

}

void Linked_List::sort_ascending(){

 if (head == nullptr){

   return;

 }

 head = merge_sort(head);

}

void swap_nodes(Node** head, Node* currX, Node* currY, Node* prevY){

   // make 'currY' as new head

   *head = currY;

   prevY->next = currX;

   Node* temp = currX->next;

   currX->next = currY->next;

   currY->next = temp;

}

Node* selection_sort(Node* head){

     // if there is only a single node

   if (head->next == NULL){

       return head;

   }

   Node* min = head;

   Node* beforeMin = NULL;

   Node *temp = head;

   while (temp->next != nullptr){

       if (temp->next->val >= min->val) {

         min = temp->next;

         beforeMin = temp;

       }

       temp = temp->next;

   }

   if (min != head){

       swap_nodes(&head, head, min, beforeMin);

   }

   // recursively sort the remaining list

   head->next = selection_sort(head->next);

   return head;

}

void Linked_List::sort_descending(){

 if (head == nullptr){

   return;

 }

 head = selection_sort(head);

}

void Linked_List::list_revese(){

 Node *temp = head->next;

 Node *prev = head;

 Node *next = NULL;

 head->next = NULL;

 while (temp != nullptr){

   next = temp->next;

   temp->next = prev;

   prev = temp;

   temp = next;

 }

 head = prev;

}

To know more about Array List visit:

https://brainly.com/question/17265929

#SPJ4

trucks, because of their large size, give the appearance of moving ____ than they actually are.

Answers

Large trucks give the impression of traveling more slowly than they actual speed do because of their size.

The exact speed that you refer to?

According to the change in the Transmitter Counts status register, the Actual Speed is the estimated speed that the axis is now moving. Position metres per second are used to measure the actual speed.

How are actual and average speeds different from one another?

The velocity you are actually moving at any given time, everywhere, is called actual speed. In order to calculate average speed, divide the distance you drove by the amount of time it took them to drive a certain distance.

To know more about speed visit:

https://brainly.com/question/28224010

#SPJ4

a natural deposit of soil is found to have a water content of 20% and to be 90% saturated. what is the void ratio of this soil?

Answers

The void ratio of the soil is 0.3125 if the soil has a water content of 20% and is 90% saturated.

The void ratio of soil is the ratio of the volume of voids (empty space) to the volume of solids in the soil. It can be calculated using the following formula:

Void ratio = Vv / Vs

where Vv is the volume of voids and Vs is the volume of solids.

We know that the soil is 90% saturated, which means that 90% of the voids are filled with water. Therefore, the volume of voids filled with water is 0.9 * Vv, and the volume of voids not filled with water is 0.1 * Vv.

We also know that the water content of the soil is 20%, which means that 20% of the total volume of the soil is water. Therefore, the volume of water is 0.2 * (Vv + Vs), and the volume of solid is (1 - 0.2) * (Vv + Vs) = 0.8 * (Vv + Vs)

Now we can substitute the values of the volume of water and solid in the void ratio equation

Void ratio = Vv / (0.8 * (Vv + Vs))

We can solve the above equation for Vv and plug in the values of the water content,

Vv = (0.2 * (Vv + Vs)) / (1 - 0.2) = 0.25 * (Vv + Vs)

Now we can substitute this value in the void ratio equation

Void ratio = 0.25 * (Vv + Vs) / (0.8 * (Vv + Vs)) = 0.25 / 0.8 = 0.3125

So the void ratio of this soil is 0.3125.

For more questions like Void ratio click the link below:

https://brainly.com/question/30266424

#SPJ4

when ineffective communicators mindlessly or thoughtlessly say and do things that they may later regret, they are ignoring which fundamental communication principle? 1. effectively use and interpret verbal messages 2. effectively use and interpret nonverbal messages 3. be aware of your communication with yourself and others 4. appropriately adapt messages to others

Answers

They are ignoring which fundamental communication principle,4. appropriately adapt messages to others' needs and expectations.

What is the communication ?

Communication is the act of exchanging ideas, thoughts, and information between people. It is a process of sending and receiving verbal and non-verbal messages. Communication can be verbal, such as speaking, or non-verbal, such as body language. It is essential for effective collaboration, as it helps to ensure that all involved parties understand the same message and can work together to solve a problem. Effective communication involves listening, understanding, and responding in a meaningful way. Good communication also involves understanding the context, purpose, and audience of the conversation.

To learn more about  communication

https://brainly.com/question/29352369

#SPJ4

A rectangular brick-lined channel (n = 0.016) of 4.0-m width is laid on a bottom slope of 0.0009. It carries a discharge of 15 m3 /s and the fl ow is non-uniform. If the depth at a Section A is 2.6 m, calculate the depth at section B, 500 m downstream of A, by using (a) only one step, and (b) two steps.

Answers

Answer:

To calculate the depth at section B, 500 m downstream of section A, we can use the Chezy formula:

V = C*R^(1/2)

Where V is the velocity, C is the Chezy coefficient, and R is the hydraulic radius.

a) Using only one step:

Since the flow is non-uniform, the velocity at section B can be assumed to be the same as at section A. Therefore, the depth at section B can be calculated using the same Chezy coefficient and hydraulic radius as at section A.

Hydraulic Radius (R) = A/P = (width * depth) / 2

R_A = (4 * 2.6) / 2 = 5.2 m

R_B = R_A = 5.2 m

Chezy coefficient (C) = (V^2 * n) / (2 * g * R^(1/2))

C = (15^2 * 0.016) / (2 * 9.81 * 5.2^(1/2)) = 1.94

Now we can use the Chezy formula to calculate the depth at section B

V = C*R^(1/2)

V = 1.94 * 5.2^(1/2) = 3.23 m/s

b) Using two steps:

First, we can calculate the velocity at section B using the continuity equation:

Q = A1 * V1 = A2 * V2

15 = (4 * 2.6 * 3.23) = (4 * y * V2)

V2 = (15 / 4) / y = 3.75/y m/s

Next, we can use the Chezy formula and the velocity at section B to calculate the depth at section B:

V = C*R^(1/2)

y = V^2 * n / (C^2 * g)

y = (3.75/y)^2 * 0.016 / (1.94^2 * 9.81)

y = 2.34 m

So, the depth at section B is 2.34 m by using two steps.

Note: The above calculations are based on the assumption that the slope is uniform along the channel and the flow is steady. In practice, other factors such as channel roughness and boundary conditions may also have an impact on the depth of flow.

You must right-click the disk name in Disk Management and select which of the following from the menu to initiate the import process?a. Corrupt Diskb. Foreign Diskc. Unknown Diskd. Import Foreign Disk

Answers

Not Initialized

Explanation

When Disk Management shows a disk icon that includes a red arrow that is pointing down, it indicates that the disk is Not Initialized.

The disk status would say Initializing if the disk is being converted from a basic disk to a dynamic disk. A Foreign disk is a dynamic disk that was created in one system and moved to another system. The Unreadable status indicates a hardware failure, I/O errors, or other corruption but might also be caused by a delay in reading the disk in Disk Management.

The importation of a foreign disk?

Open Disk Management on the new PC.Click Rescan Disks after selecting Action.Right-click any drive that is labeled Foreign.After selecting Import Foreign Disks, adhere to the on-screen directions.

To know more about Foreign Diskc visit:

https://brainly.com/question/28813522

#SPJ4

Disk Management indicates that the disk is Not Initialized when it displays a disk icon with a red arrow pointing downward.

If the disk is being converted from a basic disk to a dynamic disk, the status would show Initializing. A dynamic disk that was created in one system and transferred to another is known as a foreign disk. The Unreadable status can be brought on by a delay in reading the disk in Disk Management or by hardware failure, I/O errors, or other corruption.

Bringing in a foreign disk?

On the new PC, open Disk Management and select Action before clicking Rescan Disks. Right-click any drive with the Foreign label. Follow the instructions displayed on the screen after selecting Import Foreign Disks.

To know more about Foreign Disk :

brainly.com/question/28813522

#SPJ4

register the countchars event handler to handle blur changes for the input tag. note: the function counts the number of characters in the input.

Answers

Use the LEN function, which counts letters, digits, characters, and all spaces, to count the characters in a cell.

How do you calculate the character count?

By choosing the "Review" tab and clicking "Word Count," you may determine the number of characters in a Word document. Both the total character count including spaces and the total character count excluding spaces are available.

What is counted by the count () function?

The COUNT function counts the number of arguments in the list as well as the number of cells that contain numbers. To determine how many entries there are in a number field that is a part of a range or array of numbers, use the COUNT function.

To know more about register visit:-

https://brainly.com/question/24188927

#SPJ4

A wastewater treatment plant is testing a new adsorption CSTR to polish treated wastewater before discharge. A chemical oxidant is added to the reactor which degrades the industrial waste contaminant according to first order reaction kinetics, k = 0.22 day. The reactor volume is 450 m and the volumetric flow rate of the single inlet and exit is 40 m3/day. The inlet industrial waste concentration is 70 mg/L. a. What is the outlet concentration? b. The wastewater treatment plant engineers need to shut down the reactor for maintenance. Starting at time t=0, the concentration, Cin, entering the CSTR is set to zero. What is the outlet concentration as a function of time after the entering concentration is set to 0? c. How long does it take before the concentration in the tank reaches 15% of its initial steady-state value?

Answers

According to the problem the outlet concentration is 70 mg/L..

What is concentration?

Concentration is the act of focusing one's mental energy and attention on a particular task, activity, or object. It requires directing one's thoughts away from distractions and towards a specific goal.

a. The outlet concentration can be calculated using the equation C_out = C_in*e^(-kt), where C_in is the initial concentration of the industrial waste contaminant (70 mg/L), k is the first-order reaction rate constant (0.22 day^-1), and t is the time in days. Plugging in the given values yields C_out = 70 mg/L * e^(-0.22*t). At t = 0, the outlet concentration is 70 mg/L.

b. The outlet concentration as a function of time after the entering concentration is set to 0 can be calculated using the equation C_out = C_in*e^(-kt), where C_in is the initial concentration of the industrial waste contaminant (0 mg/L), k is the first-order reaction rate constant (0.22 day^-1), and t is the time in days. Plugging in the given values yields C_out = 0 mg/L * e^(-0.22*t). At t = 0, the outlet concentration is 0 mg/L.

c. The time it takes for the concentration in the tank to reach 15% of its initial steady-state value can be calculated using the equation t = -ln(0.15)/k, where k is the first-order reaction rate constant (0.22 day^-1) and ln is the natural logarithm. Plugging in the given values yields t = -ln(0.15)/0.22 = 3.07 days.

To learn more about concentration
https://brainly.com/question/13445467
#SPJ4

The reactor volume is 450 m and the volumetric flow rate of the single inlet and exit is 40 m3/day. The issue states that the concentration at the outlet is 70 mg/L.

What is a concentration?

Focusing one's mental energy and attention on a single activity, object, or task is known as concentration. It requires focusing on a specific objective rather than being distracted by other things.

a. The equation C_out = C_in*e(-kt), where k is the first-order reaction rate constant (0.22 day-1), C_in is the initial concentration of the industrial waste contaminant (70 mg/L), and t is the time in days, can be used to calculate the outlet concentration. C_out = 70 mg/L * e(-0.22*t) is the result of plugging in the given values.

b. The equation C_out = C_in*e(-kt), where C_in is the initial concentration of the industrial waste contaminant (0 mg/L), k is the first-order reaction rate constant (0.22 day1), and t is the time in days, can be used to calculate the outlet concentration as a function of time after the entering concentration is set to 0. C_out = 0 mg/L * e(-0.22*t) is the result of plugging in the given values.

c. The equation t = -ln(0.15)/k, where k is the first-order reaction rate constant (0.22 day-1) and ln is the natural logarithm, can be used to calculate the amount of time it takes for the concentration in the tank to reach 15% of its initial steady-state value at t = 0. When the given numbers are added up, the result is t = -ln(0.15)/0.22 = 3.07 days.

To learn more about concentration

brainly.com/question/13445467

#SPJ4

where is the resume document located in this file structure

Answers

The  "resume" has been located in the "Documents" just according to the file structure.

What is the information given in the program?

Given the information C:/Users/Documents/resume.docx, this can be interpreted as Documents is in the Users folder and the resume can be found in the Document folder.

As we can say also say that the document folder was created by the user and the "resume" file is placed directly into the documents. Based on the explanation, we can say that the  "resume" is located in the "Documents" according to the file structure.

Therefore, The  "resume" has been located in the "Documents" just according to the file structure.

Learn more about file structure on:

https://brainly.com/question/14283055

#SPJ1

Where the serving gas supplier delivers gas at a pressure greater than 2 psi for piping systems serving appliances designed to operate at a gas pressure of 14 inches of water column or less a ______ shall be installed.A) Pressure RegulatorB) Shut off ValveC) Overpressure protection deviceD) Sediment trap

Answers

For piping systems serving appliances intended to operate at a gas pressure of 14 inches w.c. or less, overpressure protection devices must be fitted when the serving gas source provides gas at a pressure greater than 2 psi.

The standard delivery pressure, or 1/3 pound-per-square-inch gauge, is usually used by residential single-family and multi-family building natural gas piping systems. An operational pressure-rated system that is rated at less than 0.5 psig must be capable of withstanding a test pressure of at least 5 psig for 30 minutes. The gas piping must withstand a pressure of at least 10 psi (69 kPa) gauge pressure during this inspection, which also includes a pressure test using air, CO2, or nitrogen.

To know more about  pressure from the given link

https://brainly.com/question/28012687

#SPJ4

where can you find a geological formation nicknamed the chocolate hills?

Answers

The Chocolate Hills are a geological structure in the Philippines' Bohol province (Mga Bungtod sa Tsokolate in Cebuano, Mga Tsokolateng Burol in Tagalog). There are at least 1,260 hills, but there could be as many as 1,776 hills located throughout a region of more than 50 square kilometres (20 sq mi).

What city are the Chocolate Hills in?

In Bohol, there are numerous villages where the Chocolate Hills may be found, including Bilar, Carmen, Butuan, and others. The viewing platform that tourists most frequently use to view these mounds is called the Chocolate Hills Complex, and it's situated in Carmen.

How did the Chocolate Hills form?

The inscription on the bronze plaque reads: "The distinctive terrain structure known as the Chocolate Hills of Bohol was produced centuries ago by the elevation of coral deposits and the activity of tectonic forces."

To know more about Tsokolateng Burol visit:

https://brainly.com/question/24197255

#SPJ4

Warm air and water both tend to rie while cooler air and water ink. When different part of the ocean are heated unevenly, thi caue the water to

Answers

Both water and warm air tend to rise while cooler air and water ink. When different parts of the ocean are unevenly heated, this causes the water to 'move in convection currents'.

In oceans, convection currents are the result of differential heating. Lighter or less dense, warm material rises while heavier or more dense cool material sinks. This is the movement that forms circulation patterns referred to as convection currents.

It means that convection currents are a current in an ocean resulting from convection. When one part of an ocean is heated, the temperature difference causes the water to move in a current or defined direction. As the heated water rises, it is replaced by cooler water.

You can learn more about convection currents at

https://brainly.com/question/20295382

#SPJ4

consider the following class definitions. public class menuitem { private double price; public menuitem(double p) { price

Answers

As a result of running the code segment, 6.5 will be printed.

What distinguishes a static method from an instance method in the most basic sense?

Which will only have one instance for a class is a static method. However, depending on the quantity of instances of that class produced, instance methods exist in multiple versions. By using a class reference, static methods can be called. Object references are used to call instance or non-static methods.

What sort of instance variable is that?

A specific instance of a class is only applicable to instance variables. Instance variables, for instance, are duplicated each time a new class object is created. Variables designated as instance variables are those that are declared inside a class but outside of any methods.

To know more about code visit :-

https://brainly.com/question/17293834

#SPJ4

As shown, a pipe is anchored to a wall at point A. (Figure 2) During the pipe's installation, several forces are applied to the pipe at different locations. If F1 = 18.8lb , F2 = 17.1lb , F3 = 19.9lb , F4 = 15.9lb , d1 = 0.350ft , d2 = 0.900ft , and d3 = 0.900ft , what is MRA, the net moment about point A due to these forces? Assume that moments acting counterclockwise about point A are positive whereas moments acting clockwise are negative.

Answers

The net moment about point A due to these forces is 41.93 lb-ft MRA.

What is forces?
Forces
are a type of interaction between objects that changes their motion or the shape of the objects. Forces can be divided into two categories: contact forces and non-contact forces. Contact forces include friction, tension, normal force, and applied force, while non-contact forces include gravity, magnetism, and electrostatic force. Forces can cause objects to accelerate, decelerate, or change direction. The strength of a force is determined by its magnitude, which is measured in newtons. Forces play a major role in many aspects of our everyday lives, from holding objects together to the motion of vehicles.

MRA = (18.8 × 0.35) + (17.1 × 0.90) + (19.9 × 0.90) + (15.9 × 0)

= 8.93 + 15.19 + 17.91 + 0

= 41.93 lb-ft

To learn more about forces
https://brainly.com/question/13441224

#SPJ4

part a: design and conduct a simulation to estimate the likelihood that the professional golfer will sink at least four holes-in-one during a single game. be sure to explain the representations and show all the work for your trials and outcomes. (6 points)

Answers

Come up with a simulation. Create and run a simulation to determine the probability that the golfer will complete at least two holes-in-one in a single game. Verify that you have completed all of the five simulation-related stages.

What in probability is a simulation?

Simulating entails employing a probability model to feign a random event, typically on a computer. We can simulate outcomes and event occurrences using a probability model.

What is the likelihood that a player in a round of golf has 0 or 1 hole in one?

In a single game of golf, there is a zero (or 25%) chance that the player will get 0 or 1 hole-in-one. Two out of the eight games meet this requirement, thus we know this.

To know more about simulation visit :-

https://brainly.com/question/16359096

#SPJ4

The sign has a mass of 90 kg with center of mass at G. (Figure 1) Determine the x, y, z components of reaction at the ball-and-socket joint A. Enter the x, y, and z components of the reaction using three significant figures separated by commas. Determine the tension in wires BC and BD. Express your answer using three significant figures separated by a comma. The sign has a mass of 90 kg with center of mass at G. (Figure 1) Determine the x, y, z components of reaction at the ball-and-socket joint A. Enter the x, y, and z components of the reaction using three significant figures separated by commas. Determine the tension in wires BC and BD. Express your answer using three significant figures separated by a comma.

Answers

the x, y, z components of reaction at the ball-and-socket joint A is:

Ax = 0 N

Ay = 529.74 N

The tension in wires BC and BD is:

Az = 441.45 N

TBD =264.87 N

Tbc = 529.71 N

What is center of mass at G?

The point through which gravity acts on an object or system is known as the centre of gravity. The gravitational field is assumed to be uniform in most mechanics problems. The centre of mass and the centre of gravity are then in the same location.

In physics, the centre of gravity is a hypothetical location within a mass of matter where, for the sake of convenience in some calculations, the mass's total weight may be assumed to be concentrated.

In astronomy and astrophysics, the centre of mass—also known as the barycenter—plays a significant role. The barycenter is the location where two objects balance one another; it is the centre of mass where two or more celestial bodies orbit one another.

To learn more about mass refers to:

brainly.com/question/19385703

#SPJ4

Which of the following is an example of the relationship between technology and positive externalities?
A. New engineering technologies allowed for better public goods.
B. Government investments in technology do not produce significant results.
C. The invention of electricity allowed many other industries to develop.

Answers

Positive externalities are effects that new technology frequently produces that are beneficial to organizations other than the one that invented it. Once these spillover effects are considered, an invention's social value usually outweighs its personal profit to the inventor.

A positive externality is a gain from making or using a product. Because people learn and acquire abilities for vocations and their lives, education, for instance, is a good externality of school. Positive externalities are a benefit of production or consumption, in contrast to negative externalities. When an advantage is shared with a third person, there is a positive externality. By taxing products and services that result in spillover costs, the government can deter harmful externalities. Through the subsidization of products and services that have positive externalities, the government can promote them.

To know more about harmful the given link

https://brainly.com/question/1428582

#SPJ4

for the frame and loaddiwn shown, there is a roller at a, a frictionless pin in slot b, and a frictionless pins at c and d
a. Determine the components of all forces acting on member BCDE. b. Display your final results on a free-body diagram with the forces acting in the proper direc- tions.

Answers

The structure in this place resembles a small frame and has a memory for both this and one between.

What are the elements of every force acting on member BCDE?

A force is a vector quantity, which means that it is associated with both a magnitude (size) and a direction. When the forces acting on an object are precisely balanced in size and direction, there is no net force acting on the object, and it is said to be in equilibrium.

The term "force" has a clear definition in science. It is perfectly acceptable to refer to a force at this level as a push or a pull. An object does not "have in it" or "contain" a force. One object is subject to a force from another. There is no distinction between living and non-living things in the concept of a force.

It may also result in changes to the body's direction, shape, size, etc. A good example is pushing or shoving a door. As a vector quantity with both magnitude and direction, force has both. The "product of a body's mass and acceleration" is how Newton's second law describes force.

To learn more about force refers to:

brainly.com/question/388851

#SPJ4

Determine the weight W that can be supported by the boom, if the maximum force that the cable T can exert is 2,000Ibs. Assume that no resultant rotation will occur at point C. (In other words, Mc = 0.)

Answers

W = Tcos(45°) + Psin(45°)

W = (2,000 lbs)cos(45°) + (0 lbs)sin(45°)

W = 1,414 lbs

What is the Law of Cosines?

This law states that the sum of the squares of the sides of a triangle is equal to the square of the hypotenuse.

The theory used in this question is the Law of Cosines.

In this case, the hypotenuse of the triangle is the cable T, the side opposite the angle of 45 degrees is the reaction force P, and the side adjacent to the angle of 45 degrees is the weight W. Using this law, we can calculate the force T and P required to support the weight W.

Step 1: Calculate the force T (the tension in the cable) that is required to support the weight W.

T = Wcos(45°)

Step 2: Calculate the force P (the reaction force at point C) that is required to support the weight W.

P = Wsin(45°)

Step 3: Substitute the values for T and P into the equation W = Tcos(45°) + Psin(45°).

W = Tcos(45°) + Psin(45°)

W = (2,000 lbs)cos(45°) + (0 lbs)sin(45°)

Step 4: Solve for W.

W = 1,414 lbs

To learn more about  Law of Cosines refer :

https://brainly.com/question/9261858

#SPJ4

Given the truss shown, with the dimensions and loads provided, find the force carried in members bc, bi, ij, de, dg, gh, and eg.

Answers

The two supports at A and D apply these reaction forces to the truss in order to maintain its stability.

What are a Truss' member troops consist of?

A truss is made up of several components that are typically joined together by pins. On the joint, there are loads or forces at work. This causes internal loadings, such as tensile or compressive force, on its members. One approach to figuring out these member forces uses the method of joints. This approach treats the joint as a location where forces are being applied to it. The system won't move unless the sum of forces acting along the x and y axes is equal to zero.

In a truss, how many forces are there?

Basic trusses are constructed from only two-force elements, with frictionless pins acting as the joints.

To know more about Truss forces visit:

https://brainly.com/question/13441224

#SPJ4

TRUE OR FALSE arpet and wood-based floor finishes should not be applied directly to slabs on grade unless the slab or finish surface temperature is

Answers

True. T/F: Unless the slabs or finish temperature increase is elevated to close to room temperature, carpet and wood-based flooring should not be directly applied to slabs on grade.

Should vapour barrier always be used?

Vapour barriers are a necessary component of building construction in several of North America's colder climes.

Should you notice nails coming from the roof into your attic?

You should ideally never be able to see the nails in your roof.Ideally, nails should be concealed by the shingle over them and flush with the flake they are placed into.The guarantees their safety and anonymity.

To know more about surface temperature visit:

https://brainly.com/question/5344945

#SPJ4

A concentrated force of 300 N is applied at point A. Determine the moment of the 300-N force about point D by conducting a cross product (vector product) and the magnitude and direction of the smallest force applied at B that creates the same moment about point D.

Answers

Therefore, MD is 41.7Nm M is the moment of force at point D.

How do you determine a force's moment?

The following equation may be used to determine the moment of a force: Minute equals Perpendicular Distance to the Pivot multiplied by Force

Moment of force is the name for the force's turning effect. It is the result of multiplying the force by the separation between the force's line of action and the pivot point or point at which the item will turn. Newton metre is the SI unit (Nm).

C-100 mm

-200 mm D

125 mm B

200 mm

25°

300 N

Therefore, MD is 41.7Nm M is the moment of force at point D.

To learn more about concentrated force refer to :

https://brainly.com/question/13716361

#SPJ4

A concentrated force of 300 N is applied at point A. As a result, MD is 41.7 Nm, and M is the moment of force at point D.

How is the moment of a force determined?

The moment of a force can be determined with the help of the following equation: The term "moment of force" refers to the turning effect of the force. Minute is equal to the perpendicular distance to the pivot multiplied by force. The result is the sum of the force multiplied by the distance between the force's line of action and the pivot point, or point at which the object will turn. The SI unit is the Newton meter (Nm).

C-100 mm -200 mm D 125 mm B 200 mm 25° 300 N, and M is the moment of force at point D.

In mechanics, what is concentrated force?

Force Concentrated: Effect of a loading that is assumed to have an effect on a body at a point (CG) provided that the load is distributed over a very small area in relation to the body's overall size. Ex: A wheel's force of contact with the ground.

To learn more about concentrated force  :

brainly.com/question/13716361

#SPJ4

Assume that the two-terminal circuit element in Fig. 1.5 of the text has the following voltage and current waveforms:v(t) = (5 + 3 cos(120πt) + 5 cos(240πt)) V,i(t) = (3 + 6 cos(120πt) + 2 cos(360πt)) ADetermine the average power P absorbed by the element.**Note that the figure in the text is just a black box diagram with total voltage v(t) and positive current i(t). It also states that p(t)=v(t)*i(t).

Answers

The total voltage in a series circuit is the sum of each of the circuit's individual voltage drops. In a series circuit, a difference in potential is created across each resistor as current flows through them.

The instantaneous voltage drop across an inductor is inversely correlated with the rate at which the current through the inductor changes. V = L (di/dt) represents the mathematical relationship. Instrument transformers of the voltage transformer (VT) and potential transformer (PT) variety are parallel-connected. They are made to put a minimal load on the supply being measured and have a precise voltage ratio and phase relationship to allow for precise secondary connected metering.

To know more about voltage  from the given link

https://brainly.com/question/13577056

#SPJ4

Which of the following expenses would not be considered an ordinary repair?
Multiple choice question.
Replacing an engine
Lubricating
Replacing small parts
Cleaning

Answers

According to the question of expenses, replacing an engine would not be considered an ordinary repair.

What is expenses?
Expenses
refer to the costs incurred in running a business or an individual's household. These costs may include the cost of goods and services purchased, wages paid to employees, payments made to vendors and suppliers, taxes, rent, and other costs associated with running a business or household. Expenses also include non-cash expenses such as depreciation, amortization, and depletion. Generally, expenses are classified as either operating expenses or non-operating expenses. Operating expenses are those that are required to generate income, such as salaries, wages, raw materials, and rent. Non-operating expenses are those that are not related to the primary operations of the company or household, such as interest expenses, donations, insurance premiums, and legal fees.

To learn more about expenses
https://brainly.com/question/29228758

#SPJ4

this layer is capable of accommodating hundreds of users. the middle process management tier controls transaction and asynchronous queuing to ensure reliable completion of transaction

Answers

Ilt has the capacity to support hundreds of people. To provide dependability, the middle process management tier regulates transactions and asynchronous queuing.

An architecture for a three-tier database consists of what levels?

The three logical and physical computing tiers that make up the well-known three-tier architecture are the presentation tier, or user interface, the application tier, where data is processed, and the data tier, where the application's associated data is kept.

What components of the Mcq three-tier architecture make up the R 3 system?

With the introduction of SAP R/3, SAP ushers in a new era of business software, moving away from mainframe computing (client-server architecture) and toward a three-tier design that includes a database, an application, and a user interface.

To know more about asynchronous queing visit:

https://brainly.com/question/29833217

#SPJ4

most operating systems have a gui as part of their system. which of the following best describes an operating system's gui?

Answers

A user-friendly interface that lets users interact with the system through icons and other visual elements.

Which is the best GUI?

PyQt5, developed by Riverbank Computing, is one of the most widely used Python graphical user interface frameworks. The Qt framework, a cross-platform framework for developing applications for a variety of platforms, is the foundation of the PyQt package.

Which of the four characteristics of a graphical user interface (GUI) can you name?

Windows, Icons, Menus, and a Pointer are the four main components that make up a GUI's four features. They are also the Interface's Main Components, or the WIMP system. MS-DOS. MS-DOS is not an operating system with a GUI.

To know more about visual elements visit :-

https://brainly.com/question/12835892

#SPJ4

A current of 20mA is Sent on a transmission line of length 10km attenuation constant of 0.1neper and phase Constant & of 0.05rad If the receiving and is short Cran estoy dot the (1) Received voltage the form (i) received current

Answers

When a signal travels via a transmission line, its amplitude lowers.

What do you mean by attenuation constant?

The phrase "attenuation constant" in communications refers to the attenuation of an electromagnetic wave travelling through a medium per unit distance from the source, also known as an attenuation parameter or attenuation coefficient. The unit of measurement is nepers per metre and refers to the real portion of the propagation constant.

Although we frequently convert to dB/meter in microwave engineering, the attenuation constant's natural units are Nepers/meter. Nepers/length must be multiplied by 8.686 to obtain loss in dB/length.

The signal's amplitude lowers as it travels through a transmission line. The symbol is used to represent it. 2. Phase sensitivity It is a part of the propagation constant that is fictitious.

To learn more about attenuation constant refer to:

https://brainly.com/question/17374622

#SPJ1

Other Questions
Which of the following would require the filing of Form 8-K?I. Major acquisitionII. Audited financial statementsIII. BankruptcyIV. Change in management controlA. I and IIIB. II and IVC. I, III, and IVD. I, II, III, and IV What are the role of enzymes in metabolism?. the sociological imagination gives us a way to look at the world beyond our own personal experience.a. trueb. false fill in the blank. when he was the republican nominee for the u.s. presidency senator mitt romney was ridiculed by the media for making a statement that is in fact accurate according to long standing legal precedent. in that statement mitt argued that___are people. FILL IN THE BLANK Mintzberg characterized managers' interaction with people both inside and outside of their work units as their _______ roles. multiple choice question. promotional Why is music considered an art form and what role does it play in people's lives?. surgical puncture with a needle to obtain a specimen of amniotic fluid The dip shrooms system was created in order to FILL IN THE BLANK Using the following general equation for a nuclear reaction, complete the statements below.The atomic number for Uranium is____ .The mass of the reactant neutron is___ .The atomic mass for Krypton is ___ .There are ___ Barium neutrons.The number of neutrons this reaction emits is ___ . what term best describes the confluence of social statuses that shape peoples lives, access to resources and power, justice, health, and well-being? Read the following paragraph: you can buy happiness, if its an experienceHow does the final sentence of the article refines key details of the text?: "We bet nobody's gotten into a fight while waiting for that oyster." Use textual evidence to support your answer. Read the following paragraph: The Long Night of the Little Boats. By basil heatter, 1970How does the figurative language in paragraph 6 help the author develop the imagery of the battle? Provide textual evidence to support your answer. What were the results and effects of World War II?. Is 16 < b + 8, if b = 22 true or false Assume that a little-endian machine currently has the data shown (in hex) below in its memory:addr: 0x48 0x49 etc. data: | AC | EF | AC | CA | FE | CA | 0D | F0 |Which address (in hex) should be put in the blank below so that the variable y holds the value 0xCAFE?short *p = ______;short y = *p; Is the main reason for writing the text?. What is the purpose of a travel allowance?. How do you find the domain of a function?. How do you write 9 more than a number?. the whole numbers are written consecutively in rows as shown. each row contains two more numbers than the previous row. $123{,}000$ is the $m$th number in the $n$th row (counting from the left). enter the values of $m$ and $n$ in this order, separated by a comma. \[\begin{array}{lccccccccc} \text{row 1} cyber corporation is performing its annual test of the impairment of goodwill for its financing reporting unit. it has determined that the fair value of the unit exceeds it carrying value. which of the following is correct concerning this test of impairment? impairment is not indicated and no additional analysis is necessary.