Let's not take into account atmospheric pressure.
Pressure P = Pressure of oil column + Pressure of water column
= h1 . d1.g + h2.d2. g
=( 0.5 x 800 x 9.8) + ( 1x 1000x 9.8) = 3920+ 9800 = 13720
Hence guage pressure at bottom is
P= 13720 N/ m^2
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 tray. If the owner wants a service level a at least 95%?
The number of trays that should be prepared if the owner wants a service level of at least 95% is; 7 trays
How to utilize z-score statistics?We are given;
Mean; μ = 15
Standard Deviation; σ = 5
We are told that the distribution of demand score is a bell shaped distribution that is a normal distribution.
Formula for z-score is;
z = (x' - μ)/σ
We want to find the value of x such that the probability is 0.95;
P(X > x) = P(z > (x - 15)/5) = 0.95
⇒ 1 - P(z ≤ (x - 15)/5) = 0.95
Thus;
P(z ≤ (x - 15)/5) = 1 - 0.95
P(z ≤ (x - 15)/5) = 0.05
The value of z from the z-table of 0.05 is -1.645
Thus;
(x - 15)/5 = -1.645
x ≈ 7
Complete Question is;
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 trays. If the owner wants a service level of at least 95%, how many trays should he prepare (rounded to the nearest whole tray)? Assume doughnuts have no salvage value after the day is complete. 6 5 4 7 unable to determine with the above information.
Read more about Z-score at; https://brainly.com/question/25638875
#SPJ1
Proper, smooth shifting is important because if you shift before your vehicle is ready
Proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
How to properly shift your gears?A proper, smooth shifting of the gears of an automobile vehicle is very important because shifting them before the vehicle is ready would cause the following:
Jer-king forward. Lock of the drive wheels.Loss of control of the vehicle.As a good driver, proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
Read more on good drivers here: https://brainly.com/question/1071840
#SPJ1
Six 20 watt, 12-volt luminaires (lighting fixtures) are supplied from a small, 12-volt transformer that is 60 feet away from the fixtures. the wire used is 14 awg. what is the voltage applied to the fixtures? use k = 11.6.
If the wire used is 14 awg. The voltage applied to the fixtures is: 8.61 volts.
Voltage applied to the fixturesFirst step is to calculate the amperes using this formula
I = P ÷ E
Where:
I =load current (amperes)=?
P =Product of voltage=(6)(20)
E =Electrical circuit's=12
Let plug in the formula
I= (6)(20) ÷ 12
I=120÷12
I= 10 amps
Second step is to calculate the Voltage drop
Using this formula
Vd = [2KIL] ÷ CMA
Where:
Vd= Voltage drop( volts)=?
K=Direct current constant=11.6
I=Load current (amperes)= 10 amps
L =Length in feet=60 feet
CMA=Circular mill area= 4110
Let plug in the formula
Vd= [(2)(11.6)(10)(60)] ÷ 4110
Vd=13,920÷4110
Vd= 3.3869 volts
Third step is to calculate Voltage at fixture
Voltage at fixtures=Electrical circuit's-Voltage drop
Voltage at fixtures=12 - 3.3869
Voltage at fixtures=8.6131 volts
Voltage at fixtures=8.61 volts (Approximately)
Therefore the voltage applied to the fixtures is: 8.61 volts.
Learn more about voltage here:https://brainly.com/question/26523307
#SPJ1
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a ____. A. word-to-word transfer B. file-to-file transfer C. word-to-file transfer D. file-to-word transfer
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a "word-to-word transfer" (Option A)
What is T4:0?
In programming, T4:0 is a time base. Whenever it is set to 1.0, it converts to the timer that counts in seconds.
It is key to note that when enumerated as T4:0 ACC, it is ascribed as an Accumulator address.
Learn more about memory locations at:
https://brainly.com/question/13104134
#SPJ1
what input is required from ADC to allow the INS to calculate W/V?
TAS is an important input which is required from ADC to allow the INS calculate W/V.
What is INS?INS is abbreviation for Inertial Navigation System and it can be defined as a navigation device that makes use of motion sensors, a computer, and rotation sensors, so as to continuously calculate by dead reckoning the velocity, position, and orientation of a moving object.
In the Aviation and Engineering filed, True Airspeed (TAS) is an important input which is required from ADC to allow the Inertial Navigation System (INS) calculate W/V.
Read more on Inertial Navigation System here: https://brainly.com/question/26052911
#SPJ12
In third ange projection draw the plain view, front view and end view.
Answer:
The front view, is a drawing of the block, as if you are looking directly at the front of the object. The side view, is a drawing of the block, when it has been rotated so that one of its sides is now directly in view. The plan view, is a 'birds eye' view, from above.
what HTML
what is CSS
Hw to create website page
Answer:
HTML (HyperText Markup Language) is the code that is used to structure a web page and its content.
CSS is Cascading Style Sheet.CSS allows you to create great-looking web pages
Explanation:
6. During some actual expansion and compression processes in piston–cylinder devices, the gases have been
observed to satisfy the relationship PVn = C, where n and C are constants. Calculate the work done when a
gas expands from 350 kPa and 0.05 m3 to a final volume of 0.25 m3
for the case of n = 1 and 1.5.
During some actual expansion and compression processes in piston-cylinder devices, the gases have been are the P1= P2.
What is the pressure?Pressure is something that has the pressure that is physical and that causes the pressure is piston-cylinder devices.
During a few real enlargements and compression procedures in piston-cylinder devices, the gases were located to meet the connection PV n = C, wherein n and C are constants.
Read more about the pressure :
https://brainly.com/question/25736513
#SPJ1
Technician A says that as long as the dog (clutch) teeth of the synchronizer are rounded, the synchronizer can be reused. Technician B says that the synchronizer sleeve should slide smoothly on its splines. Who is correct
Neither of the technicians are correct.
Who is a technician?A technician simply means an individual who looks after the technical equipments in a company.
In this case, the teeth of the synchronizer are not rounded, the synchronizer can be reused. This shows that he is incorrect likewise technician B.
Learn more about technicians on:
brainly.com/question/1548867
#SPJ12
The telescoping arm ABC is used to provide an elevated platform for construction workers. The workers and the platform together have a mass of 220 kg and have a combined center of gravity located directly above C. Assume θ = 20°.
Answer:
That is not a question...
Determine the general lighting load for a two-story office building that measures 125 feet by 150 feet.
The general lighting load for a two-story office building that measures 125 feet by 150 feet is 112, 500 sq ft.
What is lighting load?
Lighting loads are the energy used to power electric lights and they make up nearly a third of US commercial building energy use.
Lighting load = n(LW)
where;
L is length of the buildingW is width of the buildingn is number of story buildingFor one story building, = 3
For two story building, n = 6
Lighting load = 6 x 125 x 150 = 112, 500 sq ft.
Learn more about lighting load here: https://brainly.com/question/14070748
#SPJ12
A _________ can used for both entering and exiting a highway.
The lane that can be used for both entering and exiting a highway is called; A weave lane
How to enter a highway?When it comes to road highways, there are different terminologies that apply such as Acceleration lane, Deceleration Lane, Interchange, Weave lane, Urban roadway e.t.c
However, when it comes to the one that can be used for both entering and exiting a highway, the correct answer will be Weave Lane because it has both an entrance and an exit for an expressway. Traffic may come onto and leave the expressway at the same location.
Read more about road highway at; https://brainly.com/question/12961781
#SPJ12
Heater control valves can not leak coolant
True
False
Heater control valves can not leak coolant
it is true
true, heater control valves DO NOT leak coolant.
:)
A trap in the condensate line prevents ____.A) air and foreign material from being drawn up into the drain line. B.) foreign particles
A trap in the condensate line prevents D. All of the above.
What is the idea of the trap?It should be noted that the idea of the condensate drain trap is to use the weight of the water to stop the flow of air.
Based on the information given, all the options are correct. Therefore, the correct option is D.
a. air and foreign material from being drawn up into the drain line
b. additional cooling load from warm air drawn up into the air handler
c. insect invasion of the system
d. all of the above
Learn more about cooling on:
brainly.com/question/13748261
#SPJ12
ensures that enough pressure is placed on the bearing to keep the shaft from moving around, but not so much that the bearing will run hot and begin to fail. Group of answer choices End play Preload Both A and B Neither A nor B
Preload ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot.
What is preload?Preload can be defined as the load (amount of force) that is generated from an axial interference within a bearing, which causes an elastic deformation between the rolling elements and raceway.
In Engineering, preload is a technique which ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot and failing.
Read more on preload here: https://brainly.com/question/16342676
#SPJ12
The property that determines a material’s ability to conduct electricity is called?
Answer:
conductivity
Explanation:
Conductivity is the measure of the ease at which an electric charge or heat can pass through a material.
lehighedu
The results of a _________ test will determine if there is suitable drainage and the size of the drain field that will be required for a septic system.
Answer:
The results of a percolation test will determine if there is suitable drainage and the size of the drain field that will be required for a septic system.
in ipsec's __________ mode, the data within an ip packet is encrypted, but the header information is not.
In ipsec's TRANSPORT mode, the data within an ip packet is encrypted, but the header information is not.
What is ipsec's TRANSPORT mode?IPSec transport mode is known to be often used if a given tunneling protocol (like GRE) is used to try and encapsulate the IP data packet, and later on, IPSec act as a form of protection for the GRE tunnel packets.
Therefore, In ipsec's TRANSPORT mode, the data within an ip packet is encrypted, but the header information is not.
Learn more about ipsec from
https://brainly.com/question/17299146
#SPJ11
Back-fill used for underground wiring shall not damage ____________ or prevent adequate compaction of fill or contribute to corrosion.
The back-fill used for underground wiring shall not damage the raceways, cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.
What do you mean by underground wiring?A unique form of electric wiring or cable this is designed to be buried in a trench underground is known as Direct-burial cable. The character electric accomplishing wires in the cable are encased in a strong thermoplastic sheath that seals out moisture and protects the accomplishing wires within.
The complete question is given below:
(a) raceways
(b) cables
(c) conductors
(d) all of these
Thus, The back-fill used for underground wiring shall not damage the raceways, cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.
learn more about electrical wiring:
https://brainly.com/question/24786034
#SPJ1
Air is compressed from 20 psia and 70°F to 150 psia in a compressor. The compressor is operated such that the air temperature remains constant. Calculate the change in the specific volume of air as it passes through this compressor.
Answer: -8.51 ft^3/lbm
Explanation:
In this question, to find the change in volume, we will use the ideal gas law.
[tex]\begin{aligned}&n_{1}=1 \text { mole }\\&\mathrm{P}_{1}=20 \mathrm{psia}\\&\mathrm{T}_{1}=70^{\circ} \mathrm{F}\\&T_{1}=(70+460)^{0} \mathrm{R}\\&v_{1}=\frac{\left(0.3704 \frac{psia \cdot_{\text { } ft^{3}}}{l \mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{20 \mathrm{psi}}\\&v_{1}=9.816 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]\begin{aligned}&\mathrm{n}_{2}=1 \text { mole } \\&\mathrm{P}_{2}=150 \mathrm{psia} \\&\mathrm{T}_{1}=\mathrm{T}_{2}=70^{0} \mathrm{~F} \\&\mathrm{~T}_{1}=\mathrm{T}_{2}=(70+460)^{0} \mathrm{R} \\&v_{2}=\frac{\left(0.3704 \frac{\text { psia} \cdot \mathrm{ft}^{3}}{\mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{150 \mathrm{psi}} \\&v_{2}=1.309 \frac{\mathrm{ft}{ }^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]$$The change in volume is,$$\begin{aligned}&\Delta v=v_{2}-v_{1} \\&\Delta v=1.309-9.816 \\&\Delta v=-8.51 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}\text{The negative sign shows that the gas was compressed during this process}[/tex]
the best way to complete a turn requires that you
The best way to complete a turn needs that a person accelerate slowly about halfway through the turn.
What should you do when preparing to turn?If a person wants to prepare to turn, a person need to lower their speed and stay by the far right as soonest.
Therefore, The best way to complete a turn needs that a person accelerate slowly about halfway through the turn.
Learn more about completing a turn from
https://brainly.com/question/595995
#SPJ11
Technician A says electrical circuit resistance causes voltage drop. Technician B says high-resistance problems cause an increase in current flow. Who is correct
The person that is correct is Technician A as electrical circuit resistance causes voltage drop.
What is a circuit?It should be noted that an electric circuit is the path through which electric changes flow in order to conduct current.
In this case, the person that is correct is Technician A as electrical circuit resistance causes voltage drop.
Learn more about circuit on:
brainly.com/question/2969220
#SPJ12
the ____ grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning
Answer:
the jig grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning
An injector pressure drop test to see if the injector is restricted with deposits can be done using an?
An injector pressure drop test to see if the injector is restricted with deposits can be done using an integer test.
What is injector strain drop?Fuel injectors have a glide charge. This glide charge of the injector is rated at a sure strain drop throughout the injector. Meaning the injector glide is say 30#/hr at 42.five PSI. This approach that that injector will glide 30#/hr so long as the strain on the deliver side, minus the strain withinside the manifold is 42.five psiListening or Clicking Test.
Start the engine and permit it to idle. Keep the engine strolling and contact the give-up of a protracted steel screwdriver towards the gas injector. Put your ear on the alternative give up of the screwdriver. A clicking sound approaches the injector's working.
Read more about the injector pressure drop:
https://brainly.com/question/12385665
#SPJ1
As described by Bronfenbrenner, the environmental system that consists of links between microsystems is the
As described by Bronfenbrenner, the environmental system that consists of links between microsystems is the mexosystem.
What is a microsystem?It should be noted that a microsystem simply means ten pattern of activities that's expressed by an individual in a setting.
In this case, as described by Bronfenbrenner, the environmental system that consists of links between microsystems is the mexosystem.
Learn more about microsystems on:
brainly.com/question/15727382
#SPJ12
The toggle (t) flip-flop has one input, clk, and one output, q. on each rising edge of clk, q toggles to the complement of its previous value. draw a schematic for a t flip-flop using a d flip-flop and an inverter.
Answer:
See attached
Explanation:
The next state of a toggle flip-flop is the inverse of the present state. This behavior can be produced using a D flip-flop that has its input connected to the inverse of its output.
__
A schematic is attached.
The system dependent (passive) recovery process; A) never needs the use of a pump or heat to recover refrigerant. B) must use a pressure relief device to protect the technician and equipment. C) recovers refrigerant in a non-pressurized container. D) can only be performed on a system with an operating compressor.
Answer:
C) recovers refrigerant in a non-pressurized container
The system dependent (passive) recovery process recovers refrigerant in a non-pressurized container. The correct option is C.
A way of recovering refrigerant from a system without using a pump or heat is known as a system-dependent (passive) recovery process.
Instead, it relies on the system's normal pressure and temperature variations to speed up the recovery process.
A non-pressurized container is commonly connected to the system using this technique, and the refrigerant is then passively allowed to flow inside the container.
The system-dependent recovery procedure, according to Option C, recovers refrigerant in a non-pressurized container.
It entails that the refrigerant is gathered in a container without the need of a pump or additional pressure.
Thus, the correct option is C.
For more details regarding refrigerant, visit:
https://brainly.com/question/13002119
#SPJ6
Steel stirrups in reinforced concrete beams help to resist ________________. Select one: a. Bending b. Deflection c. Shear d. Tension
Answer:
Shear is the answer
hope it helps!
Draw a circuit diagram connected in a reverse bias showing a p-n material and a battery
The Circuit Diagram is connected in a reverse bias attached below.
What is Reverse Bias?Reverse biased p-n junction diode refers to the method by which a p-n junction diode stops electric current in the presence of applied voltage.
The positive terminal of the battery is connected to the n-type semiconductor material in a reverse biased p-n junction diode, while the negative terminal is connected to the p-type semiconductor material.
Learn more about Reverse biased here:
https://brainly.com/question/14703617
#SPJ1
What is software certification? Discuss its importance in the changing scenario of software industry.
The software industry is evolving, and software certification is crucial. Software certification is a digitally signed certificate that verifies the identification of an individual or company.
What is software certification?A certificate, sometimes known as a digital certificate, is a special document that has been digitally signed and authenticates the identity of a person or business.
Its validity may be checked using public-key cryptography to make sure that the program or website you are accessing is reliable.
Software developers must demonstrate that their program executes the XBRL conformance suites successfully in order to be certified.
They must also supply extra test cases so that XBRL employees can test the program further. The validity of certification is one year, renewable yearly.
Hence the software industry is evolving, and software certification is crucial.
To learn more about the software certification refer;
https://brainly.com/question/11299456
#SPJ1
