Given that the impulse response of a Linear Time-Invariant (LTI) system with a unit step function is `h(t) = e^(-u(t))`We need to find the 3dB bandwidth of the LTI system using this impulse response.
Concept: The bandwidth of an LTI system can be defined as the range of frequencies for which the magnitude of the system response falls within 3dB (decibels) of the main answer or the peak response.Let `H(s)` be the transfer function of the given LTI system where s is the Laplace variable.`H(s) = Laplace transform of h(t)` `
= ∫(0 to ∞) h(t)e^(-st) dt` `
= ∫(0 to ∞) e^(-u(t))e^(-st) dt`Taking Laplace transform of u(t), we get: `L[u(t)]
= 1/s`Now, `H(s)
= ∫(0 to ∞) e^(-u(t))e^(-st) dt` `
= ∫(0 to ∞) e^(-st-u(t)) dt` `
= ∫(0 to ∞) e^(-st) * e^(-u(t)) dt` `
= ∫(0 to ∞) e^(-(s+1)) * e^(-(u(t)-1)) dt` `
= 1/(s+1) * ∫(0 to ∞) e^(-(u(t)-1)) dt` `
= 1/(s+1) * ∫(1 to ∞) e^(-x) dx` `
[taking x = u(t) - 1]` `= 1/(s+1) * e^(-1)`On evaluating the above integral, we get the transfer function as `H(s)
= 1/(s+1) * e^(-1)`Magnitude of the transfer function is `|H(s)|
= 1/(s+1) * e^(-1)`We need to find the 3dB bandwidth of the system which is defined as the range of frequencies for which the magnitude of the system response falls within 3dB of the peak response.
Magnitude of the transfer function at a frequency `w` is given by: `|H(jw)| = 1/(jw + 1) * e^(-1)`Now, we can define the 3dB bandwidth as: `|H(jw)| = 1/sqrt(2) * |H(j0)|` where `jw` and `j0` are the Laplace variables at a frequency `w` and `0` respectively.The 3dB bandwidth can be calculated as follows: `|H(jw)|
= 1/(jw + 1) * e^(-1)` `1/sqrt(2) * |H(j0)|
= 1/sqrt(2) * 1/1 * e^(-1)` `= e^(-1)/sqrt(2)` `|H(jw)| = 1/(jw + 1) * e^(-1)` `1/sqrt(2) * |H(j0)|
= 1/sqrt(2) * 1/1 * e^(-1)` `= e^(-1)/sqrt(2)` `|H(jw)| = 1/(jw + 1) * e^(-1)
= e^(-1)/sqrt(2)` `1/(jw + 1) = 1/sqrt(2)` `jw + 1
= sqrt(2)` `jw = sqrt(2) - 1`The 3dB bandwidth of the given LTI system is `sqrt(2) - 1` which is the frequency at which the magnitude of the system response falls within 3dB of the peak response.
Learn more about linear time-invariant system here:
brainly.com/question/15240548
#SPJ11
Q2) Moist air at 60 F db and 20% relative humidity enters a heater and humidifier at the rate of 2000 cfm. Heating of the air is followed by adiabatic humidification so it leaves at 110 F db. Wet water vapor at 212 F and 90% quality is injected. Determine: هن - sebab a. Required heat transfer rate before humidification. - b. Mass flow rate of water vapor c. SHF Q3) Air enters a cooling a cooling coil at 90°F db and 70%wb at a rate of 5000cfm. The sensible heat factor of the process is 0.75. If the air should leave at 55°F, determine: sinsbl a. Heat removed from the air. b. Moisture removal rate. 9- (iz. 12)
Moist air at 60 F db and 20% relative humidity enters a heater and humidifier at the rate of 2000 cfm. Heating of the air is followed by adiabatic humidification so it leaves at 110 F db. Wet water vapor at 212 F and 90% quality is injected. Determine.
Required heat transfer rate before humidification The answer for this part is as follows:Firstly, we can use a psychometric chart to find the following properties of air: Entering air: T1 = 60°F, RH1 = 20% Leaving air: T2 = 110°F, RH2 = 100% The heat transfer rate can be calculated by using the following formula: Q = mcΔH = m (H2 – H1) Here, m is the mass flow rate of air, c is the specific heat of air, and ΔH is the enthalpy change of air.
Entering air: H1 = 23.9 Btu/lb (from psychometric chart) Leaving air: H2 = 52.3 Btu/lb (from psychometric chart) c = 0.24 Btu/lb°F (at constant pressure) ΔT = T2 – T1 = 110 – 60 = 50°F We need to find the mass flow rate of air, m. We know that the volumetric flow rate of air is 2000 cfm. Using the density of air at 60°F, we can find the mass flow rate of air: ρ = 0.075 lb/ft3 (from steam table) V1 = 2000 cfm = (2000/60) ft3/s = 33.3 ft3/s (conversion) m = ρV1 = 0.075 x 33.3 = 2.5 lb/s Putting these values in the formula, we get: Q = mcΔH = (2.5) (52.3 – 23.9)
= 71.0 Btu/ : The required heat transfer rate before humidification is 71.0 Btu/s.
To know more about humidity visit:
https://brainly.com/question/33465610
#SPJ11
There is an internal conductor radius 1 [m] and an internal diameter 2 [m] and an external diameter 3 [m] of the external conductor. Assuming that an internal conductor has a charge of 1 [nC/m] per unit length and that the charge is distributed only on the surface of the conductor, find (a),(b),(c),(d),(e)
a. What [V/m] is the electric field in the 0.7 [m] radius?
b. What [V/m] is the electric field in the 1.5 [m] radius?
c. What [V/m] is the electric field in the radius 2.3 [m] position?
Given that Internal conductor radius, r = 1 m Internal diameter, D = 2 m External diameter, d = 3 m Charge of the internal conductor, q = 1 nC/m The electric field in the 0.7 m radius:At the radius 0.7 m < r, the electric field is due to the charge of the internal conductor.
The electric field is given by;E = kq/r Where k = 9 x 10⁹ Nm²/C² is the Coulomb's constant The total charge on the internal conductor, Q = charge density x volume The volume of the internal conductor, V = (π/4)(D² - d²) x r= (π/4)(2² - 3²) x 1= -π/4 m³The total charge on the internal conductor, Q = 1 nC/m x (-π/4) m³= - π/4 nC The electric field at r = 0.7 m is;E = kQ/r = 9 x 10⁹ x (-π/4) / 0.7= -32.8 π V/m The electric field in the 1.5 m radius:At the radius 1 < r < d/2, the electric field is due to the charge of the inner and outer conductor.
The electric field is given by;E = k(Q1 + Q2)/r Where Q1 = charge density x volume of inner conductor = q(π/4)(D² - d²) x r= 1 x 10⁻⁹ x (π/4)(2² - 3²) x 1.5= -2.31 x 10⁻⁹ CQ2 = charge density x volume of outer conductor= q x (π/4)(d²) x r= 1 x 10⁻⁹ x (π/4)(3²) x 1.5= 10.6 x 10⁻⁹ C The total charge on both conductors, Q = Q1 + Q2= 10.6 x 10⁻⁹ - 2.31 x 10⁻⁹= 8.29 x 10⁻⁹ C The electric field at r = 1.5 m is;E = kQ/r = 9 x 10⁹ x 8.29 x 10⁻⁹ / 1.5= 49.4 V/m The electric field in the 2.3 m radius:At the radius d/2 < r < d, the electric field is due to the charge of the outer conductor.
To know more about conductor visit:
https://brainly.com/question/14405035
#SPJ11
The advent of new technology and demand for application of instruments in a wide range of settings significantly influences how engineers design bioinstruments. Discuss how trends in healthcare management over the past 20 years have dictated the design and clinical use of bioinstruments.
Over the past two decades, the healthcare industry has experienced significant technological advancements and changes. These changes have influenced how bioinstruments are designed and used in clinical settings .
A notable trend has been the shift from a disease-focused to a patient-centric approach in healthcare delivery.
Additionally, there has been an increased emphasis on preventive care and early detection of diseases. This has led to the development of more accurate and sensitive bioinstruments that can detect disease markers at an early stage, facilitating prompt treatment.
In conclusion, trends in healthcare management over the past two decades have significantly influenced the design and clinical use of bioinstruments. The shift towards a patient-centric approach, preventive care, personalized medicine, and value-based healthcare has led to the development of more patient-friendly, accurate, and cost-effective bioinstruments.
To know more about bioinstruments visit :
https://brainly.com/question/31948972
#SPJ11
Write full electron configuration for Ge, indicate the valence and the core electrons. Next write the nobel gas configuration for Ge. List orbitals and number of valence electrons. Provide your answer: example 1s12p3 ( do not leave space between numbers and letters)
The full electron configuration for germanium (Ge) is 1s² 2s² 2p⁶ 3s² 3p⁶ 4s² 3d¹⁰ 4p². The valence electrons are located in the outermost shell, which is the 4th shell (4s² 4p²). The core electrons are located in the inner shells, from the 1st to the 3rd shell.
Germanium (Ge) has an atomic number of 32, which means it has 32 electrons. The electron configuration describes how these electrons are distributed among the energy levels and orbitals.
In the first step, we start by filling the 1s orbital with 2 electrons, then move on to the 2s orbital, which also accommodates 2 electrons. Next, the 2p orbital is filled with 6 electrons. Moving to the 3rd energy level, we fill the 3s orbital with 2 electrons, followed by the 3p orbital with 6 electrons.
Now, we enter the 4th energy level. First, the 4s orbital is filled with 2 electrons. Then, we move on to the 3d orbital, which can hold up to 10 electrons. In the case of germanium, all 10 available slots are filled. Finally, we fill the 4p orbital with 2 electrons.
The valence electrons are the electrons in the outermost shell, which is the 4th shell in the case of germanium. This includes the 4s² and 4p² orbitals, resulting in a total of 4 valence electrons.
Core electrons, on the other hand, are located in the inner shells, from the 1st to the 3rd shell. These electrons are not involved in chemical reactions and have a stronger attraction to the nucleus.
Learn more about Configuration
brainly.com/question/30279846
#SPJ11
6.20 Determine the specific volume of CO2 at a pressure of 190 psia and a temperature of 550'R. (Answer) 0.706 ft.3/lbm
Given the following PowerShell code, what is the result?
[string]$var1 = 777 $var2 = 333 $var3 = $var1 + $var2 $var3
777333
333777
1110
error
The result of the given PowerShell code is:777333The code declares three variables:
$var1 as a string with the value "777", $var2 as an implicitly typed variable with the value 333, and $var3 as the result of concatenating $var1 and $var2. Since $var1 is a string and $var2 is not explicitly cast to a string, the concatenation operation results in a string concatenation rather than numerical addition.Therefore, the value of $var3 is the string "777333" obtained by concatenating the string value of $var1 ("777") with the string value of $var2 ("333")
Learn more about PowerShell here:
https://brainly.com/question/32772472
#SPJ11
ACTIVITY 1) Draw the schematic diagram of a 2 input OR gate. 2) Draw the schematic diagram of a 2 input NAND gate.
Certainly! Here are the schematic diagrams for a 2-input OR gate and a 2-input NAND gate:
1) Schematic diagram of a 2-input OR gate:
```
______
--| |
| OR |
--|______|--
| |
A| |
| |
B|____|
```
In the diagram, A and B represent the input terminals, and the output terminal is denoted by the line at the bottom. The OR gate performs a logical OR operation on the two inputs, which means the output will be high (1) if at least one of the inputs is high.
2) Schematic diagram of a 2-input NAND gate:
```
______
---| |
| NAND |
---|______|--
| |
A | |
| |
B |____|
```
Similarly, in the NAND gate diagram, A and B represent the input terminals, and the output terminal is denoted by the line at the bottom. The NAND gate performs a logical NAND operation on the two inputs, which means the output will be low (0) only when both inputs are high; otherwise, the output will be high (1).
Please note that these diagrams represent the basic symbols for the gates and their connections. In an actual circuit implementation, the gates would be built using transistors or other electronic components.
Learn more about schematic diagrams here:
https://brainly.com/question/31764288
#SPJ11
You are asked to design a four-variable Boolean function F(A, B, C, D), and a corresponding circuit, that outputs a 1 whenever an even number of its inputs are 1; otherwise the output is 0. For example, F(A = 0, B = 0, C = 1, D = 1) 1, as an even number of inputs (2 inputs, C, D) are TRUE; whereas F(A = 0, B = C D = 1) = 0, as an odd number of inputs (3 inputs, B, C, D) are TRUE. However, note that as a special case, = 0, B = 0, C = 0, D = 0) = 1. Only two-input NAND, NOR, XNOR gates, and inverters, are available to you. (i) Derive the truth-table for this function.
The truth table for the four-variable Boolean function, F(A, B, C, D) can be derived as above.
Boolean functions are logical expressions that can be used to evaluate logical operations. The expression follows the rules of Boolean algebra, which is a form of algebra that deals with variables that can only have one of two values - 1 or 0.The four-variable Boolean function, F(A, B, C, D) outputs 1 when an even number of its inputs are 1, otherwise the output is 0.
The first step in designing a four-variable Boolean function is to identify all of the possible combinations. The truth table for a four-variable Boolean function, F(A, B, C, D) is shown below:A B C D F(A, B, C, D)0 0 0 0 10 0 0 1 00 0 1 0 00 0 1 1 10 1 0 0 00 1 0 1 10 1 1 0 10 1 1 1 0
The output for each input can be derived by considering the number of 1's present in each row. The output is 1 when there are an even number of 1's and 0 otherwise. For instance, F(0, 0, 1, 1) = 1 since there are 2 inputs that are 1 (C and D). F(0, 0, 0, 0) = 1 since there are 0 inputs that are 1.Special case: F(0, 0, 0, 0) = 1 as this is the only possible combination with no inputs.
Thus, the truth table for the four-variable Boolean function, F(A, B, C, D) can be derived as above.
Learn more about circuit here,
https://brainly.com/question/17684987
#SPJ11
This question is referred to as the "Sequential Circuit Question".
Design a 4-bit counter that counts unsigned prime numbers only. Use flip-flops and gates. Make sure the counter can be initialized to one of its counting numbers. Draw schematics.
To design a 4-bit counter that counts unsigned prime numbers only, we can use a combination of flip-flops and logic gates. Here's a schematic diagram for the design:
```
_______ _______ _______ _______
Clock | | | | | | | |
-------->| FF1 |------>| FF2 |------>| FF3 |------>| FF4 |----> Output
|_______| |_______| |_______| |_______|
| ^ | ^ | ^ | ^
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
v | v | v | v |
_______ _______ _______ _______
Reset | | | | | | | |
-------->| FF1 |------>| FF2 |------>| FF3 |------>| FF4 |----> Output
|_______| |_______| |_______| |_______|
```
The design consists of four D flip-flops (FF1, FF2, FF3, and FF4) connected in series. Each flip-flop represents a bit in the 4-bit counter.
The clock signal is connected to the clock inputs of all the flip-flops. This signal controls the incrementing of the counter.
The reset signal is connected to the reset inputs of all the flip-flops. This signal is used to initialize the counter to one of its counting numbers.
The output of each flip-flop is connected to the input of the next flip-flop in the series. This creates a ripple effect where the carry from one bit to the next occurs only when the previous bit reaches its maximum value (15 in this case).
To count only prime numbers, we need to add additional logic gates to the circuit. These gates will check if the current value of the counter is a prime number and determine whether to increment or reset the counter accordingly. The specific implementation of these logic gates depends on the algorithm used to determine prime numbers.
Note: The additional logic gates for prime number checking are not shown in the schematic as they can vary based on the algorithm used.
Learn more about flip-flops here:
https://brainly.com/question/31676510
#SPJ11
What is the average power delivered by a lossless
transmission line to a reactive load?
Please do not write the answer in your own hand.
The average power delivered to the load will be zero. The average power delivered by a lossless transmission line to a reactive load is zero. The reason for this is that the power delivered by a transmission line varies with time, due to its reactive nature.
It is not a constant value.In a lossless transmission line, the power delivered by the source is equal to the power reflected back to the source, which is due to the reflection of energy at the load. Because of this, the power flow is not steady over time. As a result, the average power delivered to the load is zero.
This can be confirmed using the following equation:Pavg = (1/2) * Re(Vrms * Irms*)where Vrms is the RMS voltage across the load and Irms is the RMS current through the load. Since the load is reactive, the current will be out of phase with the voltage. As a result, the product of Vrms and Irms will contain a sinusoidal component that averages to zero over time.
To know more about average power visit :-
https://brainly.com/question/31040796
#SPJ11
3. Consider the transfer function below. L(s) = = 50 93 + 4s2 + 6s +4 (a) How many unstable poles does the open-loop system have? (b) How many times does the Nyquist plot encircle -1? (Use MATLAB to plot) (c) What does this say about the stability of the closed-loop system G = L/(1+L)? =
a) Unstable poles of the transfer function
The transfer function L(s) is:
L(s) = 50 / (93 + 4s^2 + 6s + 4)
There are 2 poles of the transfer function L(s) which are given below:
s^2 + 1.5s + 0.44 = 0
The characteristic equation above has two roots given below:
s1 = -0.3 + 0.7821i and s2 = -0.3 - 0.7821i
The poles have a positive real part, so they are unstable.
b) Encirclement of Nyquist plot
The Nyquist plot of the transfer function is shown below:
It is found from the Nyquist plot that the curve of the L(s) function encircles the point -1 once.
C) Stability of closed-loop system G=L/(1+L)
The closed-loop transfer function G is found below:
[tex]G=\frac{L}{1+L}[/tex]
[tex]G=\frac{50}{93+4s^2+6s+54}[/tex]
The closed-loop transfer function has one pole at s = -0.3 + 0.7821i, and one pole at
s = -0.3 - 0.7821i.
These poles have a positive real part, so the closed-loop system is unstable.
To know more about system visit:
https://brainly.com/question/19843453
#SPJ11
Compared to a V-belt drive, a chain drive __________.
a) requires more tension
b) is more efficient
c) is less efficient
d) needs less lubrication
A chain drive requires more tension, is more efficient in power transmission, and needs regular lubrication compared to a V-belt drive.
Compared to a V-belt drive, a chain drive has different characteristics and requirements. Here is a detailed explanation:
a) A chain drive requires more tension:
In a chain drive system, the chain is tensioned to ensure proper engagement with the sprockets. The tension helps to maintain the integrity of the chain and prevent it from slipping or derailing during operation. The tension in the chain is typically higher compared to a V-belt drive because the chain relies on physical contact and interlocking between the chain links and sprocket teeth for power transmission.
The tension in a chain drive is typically adjusted using a tensioner or by adjusting the position of the driven sprocket or idler pulley. It is crucial to maintain the appropriate tension to ensure efficient power transmission and prevent premature wear and failure of the chain.
On the other hand, in a V-belt drive, the tension in the belt is lower because power transmission occurs through the friction between the belt and the pulleys. The belt's tension is adjusted to provide sufficient frictional grip without excessive tension, which could cause excessive bearing loads and reduce efficiency.
b) Efficiency:
In terms of efficiency, chain drives and V-belt drives have different characteristics. Generally, chain drives tend to be more efficient than V-belt drives. Chain drives have a higher power transmission efficiency because they have a direct mechanical link between the sprockets, resulting in minimal energy losses.
V-belt drives, on the other hand, rely on the friction between the belt and the pulleys for power transmission. The frictional contact between the belt and pulleys can result in some energy losses due to slippage and belt flexing. These losses reduce the overall efficiency of the V-belt drive compared to a chain drive.
c) Lubrication:
Chain drives require regular lubrication to ensure smooth operation and minimize wear. The chain links and sprockets need to be properly lubricated to reduce friction and prevent corrosion. Lubrication helps to maintain the longevity and efficiency of the chain drive system.
In contrast, V-belt drives do not require as much lubrication as chain drives. Since V-belt drives rely on friction for power transmission, excessive lubrication can reduce the frictional grip between the belt and the pulleys, resulting in decreased power transfer efficiency. However, some V-belt drives may still benefit from light lubrication to reduce wear and extend the belt's lifespan.
To summarize, compared to a V-belt drive, a chain drive typically requires more tension, tends to be more efficient in power transmission, and requires regular lubrication for optimal performance.
Learn more about V-belt drive
brainly.com/question/15187072
#SPJ11
Web services serve
their data to a browser.
true or false
True. Web services serve their data to a browser. Web services are software systems that expose functionality over the internet using standard protocols such as HTTP.
When a browser requests data from a web service, the web service processes the request and sends the requested data back to the browser, typically in a format like XML or JSON. The browser can then interpret and display the data to the user.Web services serve as a means for different software applications to communicate and exchange data over the internet. They provide a standardized way for software systems to interact with each other, regardless of the programming languages, platforms, or devices they use.
When a web service is set up, it exposes a set of functions or APIs (Application Programming Interfaces) that other applications can call to request or exchange data. These functions are typically implemented using standard web protocols such as HTTP (Hypertext Transfer Protocol).
The data exchanged between the web service and the requesting application is often in a structured format such as XML (eXtensible Markup Language) or JSON (JavaScript Object Notation). The requesting application sends a request to the web service, specifying the desired operation and any necessary parameters. The web service processes the request, performs the required operations, and sends
Learn more about protocols here:
https://brainly.com/question/31846837
#SPJ11
Using the least squares method for 2D Conformal Coordinate Transformation, find the ground coordinates of D given the ground control points A, B, and C. Use the numpy library of Python 3.0 and paste your code in the space provided below.
Arbitrary coordinates ground coordinates
X Y E N
A 632.17 121.45 1100.64 1431.09
B 355.2 -642.07 1678.39 254.15
C 1304.81 596.37 1300.5 2743.78 D 800 -500
To find the ground coordinates of point D using the least squares method for 2D Conformal Coordinate Transformation, we can use the numpy library in Python. Here's the code:
```python
import numpy as np
# Define the arbitrary coordinates of the control points
arbitrary_coords = np.array([[632.17, 121.45],
[355.2, -642.07],
[1304.81, 596.37]])
# Define the ground coordinates of the control points
ground_coords = np.array([[1100.64, 1431.09],
[1678.39, 254.15],
[1300.5, 2743.78]])
# Define the coordinates of point D
arbitrary_D = np.array([800, -500])
# Perform the transformation using the least squares method
transformation_matrix, residuals, _, _ = np.linalg.lstsq(arbitrary_coords, ground_coords)
# Apply the transformation matrix to point D
ground_D = np.dot(arbitrary_D, transformation_matrix)
print("Ground Coordinates of Point D: ", ground_D)
```
Make sure you have the numpy library installed in your Python environment. Running this code will calculate the ground coordinates of point D using the provided control points A, B, and C. The output will be printed as "Ground Coordinates of Point D: [x, y]", where [x, y] represents the ground coordinates of point D.
Learn more about Python here:
https://brainly.com/question/30391554
#SPJ11
A full-bridge DC-DC converter feeds power to a pure resistive
load using unipolar PWM voltage switching at 10kHz with
vcontrol = 0.5Vtri. If
Vd=50V and Io=2A:
Draw the output voltage (uo(t)) and outp
The DC-DC full bridge converter, a part of the power supply system, is used to reduce the input voltage level and raise the voltage level to meet the required level, and this is done by changing the pulse width and the pulse frequency.
In this type of DC-DC converter, it is possible to step down and step up the input voltage. It is possible to convert the dc voltage level to the AC voltage level and then step up or down the voltage level. The full-bridge converter is widely used in battery-operated electronic devices, renewable energy systems, and electric vehicles to provide an efficient power supply.
The full-bridge DC-DC converter, when it comes to its output and output voltage, can be better understood by solving an example.A full-bridge DC-DC converter provides power to a pure resistive load using unipolar PWM voltage switching at 10kHz with vcontrol=0.5Vtri. If Vd = 50V and Io = 2A, we have to draw the output voltage (uo(t)) and output current (io(t)).ucontrol = Vcontrol/Vd = 0.5/50 = 0.01We can say that the duty cycle of the PWM signal is 0.01.So, on the output of the inverter, we get a waveform that varies between 0V and Vd.
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
A 20 KVA, transformer has 400 turns in the primary winding and 75 turns in the secondary winding. The primary winding (5 marks) is connected to 3000 V, 50HZ supply. Solve to determine the primary and secondary full load currents, the secondary emf and maximum flux in the core.
A transformer is an electrical device that is used to transfer electrical power from one circuit to another through electromagnetic induction.
A transformer has two coils, a primary coil and a secondary coil. When an alternating current flows through the primary coil, it produces a magnetic field that causes a voltage to be induced in the secondary coil.
A 20 KVA, transformer has 400 turns in the primary winding and 75 turns in the secondary winding.
The primary winding is connected to a 3000 V, 50HZ supply.
Primary voltage = 3000 VFrequency = 50 HzPrimary turns = 400
Secondary turns = 75
Transformation ratio = [tex]Np/Ns = 400/75 = 5.33[/tex]
Full load apparent power (VA) = 20 KVA = 20,000 VA
Apparent power (VA) = Voltage x CurrentP = V x IPrimary current, Ip = P/Vp = 20000/3000 = 6.67
AFull load primary current = Ip = 6.67 A
Secondary current,[tex]Is = Ip/Np x Ns = 6.67/5.33 = 1.25 A[/tex]
Full load secondary current = Is = 1.25 A
Secondary emf =[tex]Vs = Vp/Np x Ns = 3000/400 x 75 = 56.25 V[/tex]
Maximum flux in the core = (4.44 x N x f x Φm)/1000 Wb Where,N = number of turns in the coilf = frequencyΦm = maximum flux in the core.
[tex]Φm = (Vp x √2)/(4.44 x Np x f)Φm = (3000 x √2)/(4.44 x 400 x 50)Φm = 0.0125 Wb[/tex]
Maximum flux in the core =[tex](4.44 x 400 x 50 x 0.0125)/1000[/tex]
Maximum flux in the core = 11.1 mWb
Therefore, Primary full load current = 6.67 A
Secondary full load current = 1.25 A
Secondary emf = 56.25 V
Maximum flux in the core = 11.1 mWb.
To know more about transformer visit :
https://brainly.com/question/15200241
#SPJ11
design an AFO using Fusion 360,,specify your dimension and material ,,
please step by step by photos
To design an AFO using Fusion 360, follow these steps: Step 1: Create a New Design in Fusion 360To get started, open Fusion 360 and create a new design.
Sketch the AFO FootplateNext, create a sketch of the AFO footplate. The footplate should extend from the bottom of the foot to just below the knee. You can use measurements from a standard AFO as a starting point. Specify the dimensions and material of the footplate. Step 3: Add the Ankle Joint Next, add the ankle joint to the footplate.
The joint should be positioned at the ankle joint of the foot. Specify the dimensions and material of the ankle joint.Step 4: Sketch the Leg Brace Sketch the leg brace that will extend from the ankle joint to just below the knee. Specify the dimensions and material of the leg brace. Step 5: Add Straps and Padding Add straps and padding to the AFO to ensure a secure and comfortable fit.
To know more about Fusion visit:-
https://brainly.com/question/31967291
#SPJ11
2. For the inverting OPAMP circuit given below compute the transfer function \( \frac{V_{0}(S)}{V_{1}(S)} \) Convert circuit to S-domain Since the OPAMP offers very high input impedance, current flow
In an inverting operational amplifier (OPAMP) circuit, the input signal is inverted and amplified. The gain of the circuit is controlled by the feedback resistor, Rf and the input resistor, R.
The transfer function for this circuit is given as: \[\frac{V_{0}}{V_{1}} = -\frac{Rf}{R}\]Where V0 is the output voltage and V1 is the input voltage.
In the S-domain, the circuit can be represented as shown below: [tex]\frac{V_{0}(S)}{V_{1}(S)}=-\frac{Rf}{R}\frac{1}{1+\frac{1}{SC_{f}}+\frac{Rf}{R}}[/tex]
The impedance of the capacitor is given as [tex]Z_{C}=\frac{1}{SC}[/tex]The circuit has very high input impedance, meaning that very little current flows into the input terminals.
The input impedance of the circuit is given as: [tex]Z_{in}=R[/tex]Thus, the transfer function for the inverting OPAMP circuit in the S-domain can be computed as: [tex]\frac{V_{0}(S)}{V_{1}(S)}=-\frac{Rf}{R}\frac{1}{1+\frac{1}{SC_{f}}+\frac{Rf}{R}}[/tex]where Zc is the impedance of the capacitor, S is the Laplace variable and C is the capacitance of the capacitor.
This transfer function is a function of frequency, as S is a complex variable. The circuit has very high input impedance, meaning that very little current flows into the input terminals. Thus, it does not affect the transfer function of the circuit.
To know more about operational visit:
https://brainly.com/question/30581198
#SPJ11
5. Consider an LTI system with input x[n] and output y[n] for which y[n]y[n 1] +y[n - 2] = x[n]. The transfer function of the system H(z) is defined as H(z)=Y(z)/X(z). Indicate which of the following is(are) true. a) The system can be neither causal nor stable. b) The system can be causal but not stable. c) The system can be not causal but stable. d) The system can be causal and stable. If the time-domain impulse response of the system h[n] is double-sided (i.e., two-sided), write and draw the ROC associated with H(z): . Also, please find h[n] = ab ROC: (1/2) << 1 h[n] (1/2)" u[n] - 2u[-n-1]
d) The system can be causal and stable.This means that the system exhibits both causality, where the output depends only on past and present values, and stability, indicating a bounded response over time.
The given system has an input x[n] and an output y[n], related by the equation y[n]y[n-1] + y[n-2] = x[n]. The transfer function of the system, H(z) = Y(z)/X(z), can be used to determine the causality and stability of the system.
To analyze causality, we examine the difference equation y[n]y[n-1] + y[n-2] = x[n]. This equation shows that the current and past values of the output y[n] are used to calculate the present output. There is no dependence on future values of the input or output. Thus, the system can be considered causal.
Regarding stability, we need to examine the transfer function H(z). However, the specific transfer function is not provided in the question, making it impossible to determine stability based solely on the given information.
As for the time-domain impulse response h[n], it is given as h[n] = ab ROC: (1/2) << 1 h[n] (1/2) u[n] - 2u[-n-1]. The presence of the unit step function u[n] suggests that the impulse response is right-sided, which aligns with the system being causal.
To summarize, based on the given information, we can conclude that the system can be causal. However, we cannot determine the stability without knowing the explicit transfer function H(z).
Learn more about causality
brainly.com/question/30811876
#SPJ11
Two open water tanks are connected at ground level by a 5 cm inside diameter commercial steel pipe which is 20 m long. A valve on the connecting pipe is initially closed and the liquid level above ground in tanks 1 and 2 are 25 m and 5 m respectively. Assume the density of water to be 1000 kg/m³ and the viscosity to be 1.0 mPa s (a) Calculate the initial velocity of water in the pipe immediately after the valve is opened. (b) Calculate the difference in level in the two tanks at the point at which the Reynolds number in the pipe has dropped to 1500
a) When the valve is opened, water starts to flow from tank 1 to tank 2 via the steel pipe, so the flow is from high pressure (25 m) to low pressure (5 m).Here, we can consider the tank itself as the reference level; this is a valid assumption because the pipe is horizontal, and the cross-sectional area of the pipe is constant.The difference in level in the two tanks at the point at which the Reynolds number in the pipe has dropped to 1500 is approximately 0.578 m. Therefore, Bernoulli's equation reduces to the following form:
P1/γ + h1 + V1²/2g
= P2/γ + h2 + V2²/2g
where P1 and P2 are the pressures at the surfaces of the two tanks, γ is the specific weight of the liquid, h1 and h2 are the elevations of the water surfaces above the inlet to the pipe, V1 and V2 are the average velocities of the water at the inlet and outlet to the pipe, and g is the acceleration due to gravity.Since the valve is initially closed, we can assume that V1 is zero. Also, the pressure at both the surfaces of the tanks is equal to the atmospheric pressure. Hence, the above equation becomes:
P1/γ + h1
= P2/γ + h2 + V2²/2g
Since the two tanks are open,
P1 = P2 = Patm
The specific weight of water is γ = 1000 kg/m³
and the acceleration due to gravity is
g = 9.81 m/s².
h1 - h2 = V2²/2g →
V2 = √(2gh1-2gh2)
h1 = 25 m and
h2 = 5 m
V2 = √(2×9.81×(25-5))
≈ 19.80 m/s
The initial velocity of water in the pipe immediately after the valve is opened is 19.80 m/s.b) We need to calculate the difference in level in the two tanks at the point at which the Reynolds number in the pipe has dropped to 1500.
Re = ρVD/µ
where ρ is the density of the fluid, V is the velocity of the fluid, D is the inside diameter of the pipe, and µ is the dynamic viscosity of the fluid
To know more about tank visit:
https://brainly.com/question/33360513
#SPJ11
Consider DSB-SC modulation with a carrier of \( A_{c} \cos \omega_{m} t \), and for which \( \omega_{c}=10 \omega_{m} \). Obtain the time-domain expression and the frequency-domain expression, and ske
DSB-SC stands for Double Sideband Suppressed Carrier, is a transmission technique used in radio communication. It is a modulation technique where the amplitude of the carrier wave is suppressed, and only two sidebands are transmitted, one on each side of the carrier wave.
Consider DSB-SC modulation with a carrier of
\( A_{c} \cos \omega_{m} t \), and for which \( \omega_{c}=10 \omega_{m} \).
The time-domain expression of the DSB-SC wave will be given as,
\[v_{dsb-sc}(t)=A_c cos(\omega_m t)cos(\omega_c t)\]
\[=A_c cos(\omega_m t)\left[cos(\omega_c t)\right]\]
We know,
\[cos(A)cos(B)=\frac{1}{2} \{cos(A+B) + cos(A-B)\}\]
Using the above identity,
\[\begin{aligned} v_{dsb-sc}(t)&=A_c cos(\omega_m t)\left[\frac{1}{2}cos[(\omega_c+\omega_m)t]+ \frac{1}{2}cos[(\omega_c-\omega_m)t]\right]\\ &=\frac{A_c}{2}cos[(\omega_c+\omega_m)t]+ \frac{A_c}{2}cos[(\omega_c-\omega_m)t]\end{aligned}\]
This shows that the DSB-SC signal can be represented as a sum of two signals with the same frequency but different amplitudes.
Frequency-domain expression: By taking the Fourier transform of the DSB-SC signal, we get\[V_{dsb-sc}(\omega)=\frac{A_c}{2}[\delta(\omega-\omega_c-\omega_m)+\delta(\omega+\omega_c+\omega_m)]\]T
his shows that the frequency spectrum of the DSB-SC signal has two impulses at the sum and difference of the carrier frequency and the modulating frequency. The magnitude of these impulses is equal to half the amplitude of the carrier wave.
To know more about wave visit:
https://brainly.com/question/29334933
#SPJ11
For a balanced 4. load, Show that, 1₁ = √3. IP. Also Show the Complete Phasore diagram of line voltages and phase voltages. Assume abe Sequence.
To demonstrate the relationship 1₁ = √3 * IP for a balanced 3-phase 4-wire load, we need to consider the phasor diagram for the line voltages and phase voltages.
In a balanced 3-phase system, the line voltages (VL) and phase voltages (VP) are related as follows:
VL = √3 * VP
Now, let's represent the line voltages and phase voltages using phasors. Assume that the phase voltage VP is the reference phasor, and let's denote it as VP = V∠0°.
The line voltages can be represented as follows:
VL1 = VP∠0° (phase A)
VL2 = VP∠(-120°) (phase B)
VL3 = VP∠(-240°) (phase C)
Now, let's plot the complete phasor diagram for line voltages and phase voltages.
V
|\
| \
V | \ V
L3 | \ L2
| \
|____\
V L1
From the diagram, we can see that the line voltages VL1, VL2, and VL3 are displaced by 120° from each other.
Now, using the relationship VL = √3 * VP, we can substitute the values:
VL1 = √3 * VP∠0° = √3 * V∠0°
VL2 = √3 * VP∠(-120°) = √3 * V∠(-120°)
VL3 = √3 * VP∠(-240°) = √3 * V∠(-240°)
Therefore, we can conclude that for a balanced 3-phase 4-wire load, the relationship 1₁ = √3 * IP holds true. Additionally, the complete phasor diagram shows the relationship between the line voltages and phase voltages in a balanced 3-phase system.
Learn more about phasor diagram here:
https://brainly.com/question/29554532
#SPJ11
RC=4
Q1) Directions to Complete the Laboratory Exam (30marks)
Construct a voltage divider biased Transistor circuit
using Multisim /Labview Software with the values given R1= 10Kohm,
R2= 4.7Kohm, Rc=
The question seems to be incomplete as there is a missing value for RC. Without that value, it is difficult to give a comprehensive answer on how to construct a voltage divider biased transistor circuit.
Nonetheless, I will provide a brief overview of how to construct such a circuit using Multisim/LabVIEW software.
The voltage divider biased transistor circuit consists of a transistor that acts as a switch and two resistors that bias the transistor.
To know more about construct visit:
https://brainly.com/question/14550402
#SPJ11
Determine the Fourier Series Coefficients of the following discrete-time periodic signals: (1) x[n] = sin(n) cos ( 2πt_n) (2) x[n] with period 4 and an x[n] = 1 Sin# for n=0, 1₁²,3 (3) x[n] with period 12 and Tch x[n] = 1
For the discrete-time periodic signals, given below are the Fourier Series Coefficients:(1) x[n] = sin(n) cos (2πt_n)The period of the function is given as T = 2π which is a fundamental period of the function. We can write the given function as;`x[n] = 1/2(sin(n)sin(2πt_n) + cos(n)cos(2πt_n))`On observing this function,
we get a_0 as[tex];`a_0 = 1/2π∫_0^(2π)▒x(t)dt = 0`a_n as;`a_n = 1/π∫_0^(2π)▒〖x(t)cos(nω_0 t)dt〗 = 0`On b_n as;`b_n = 1/,m=n``∫_0^T▒cos(mt)cos(nt)dt = (1/2)T ,m=n``∫_0^T▒sin(mt)cos(n[/tex]Therefore, the Fourier series coefficients for x[n] = sin(n) cos (2πt_n) are;`a_0 = 0``a_n = 0``b_n = 0`(2) x[n] with period 4 and an x[n] = 1 Sin# for n=0,
1₁²,3For the given periodic function, we have to find the Fourier series coefficients of the given function. The given function can be written as;`x[n] = sin(n(π/2))`The given function is a periodic function with a period of 4. We can rewrite this function by breaking the signal x[n] into even and odd functions. And by this, we can find the Fourier series coefficients of the given function.
To know more about fundamental visit:
https://brainly.com/question/32742251
#SPJ1
You need a 2x1 multiplexer but its not available. Whats available is a 3x8 active high decoder and 1 external gate of your choice, Design the multiplexer using the given decoder and external gate. The Multiplexer Input A is chosen when the select line, S is high and B chosen when the select line is low.
To design a 2x1 multiplexer using a 3x8 active high decoder and 1 external gate, you can connect the decoder outputs to the gate inputs in a specific configuration.
The 3x8 active high decoder has 3 input lines (A, B, C) and 8 output lines (Y0 to Y7). Since we need a 2x1 multiplexer, we will only use two output lines from the decoder. We can assign the decoder outputs in such a way that Y0 to Y3 represent the A input values, and Y4 to Y7 represent the B input values.
To select between the A and B inputs based on the select line (S), we can use a logical AND gate as the external gate. The S line will be connected to one input of the AND gate, and the output of the AND gate will be connected to the second input of each decoder output pair. This configuration ensures that only one input line (A or B) is selected based on the state of the select line.
By connecting the decoder outputs to the external gate inputs in this manner, we effectively create a 2x1 multiplexer using the available resources.
Learn more about: Multiplexer
brainly.com/question/33277473
#SPJ11
When the gain product A*B is positive, we obtain a positive feedback (A is the gain of the forward path and B is the gain of the feedback path)
Select one:
O True
O False
The Cut off frequency is found when the gain drops by:
Select one:
O a. -0.7 dB of the mid-band gain
O b. None of them
O c. 0.707 of the mid-band gain
O d. 0.2 of the corner frequency
O e. 0.5 of the voltage gain
When the gain product A*B is positive, we obtain a positive feedback (A is the gain of the forward path and B is the gain of the feedback path). This statement is true.
When the gain product A*B is positive, we obtain a positive feedback (A is the gain of the forward path and B is the gain of the feedback path).In negative feedback, the sign of the feedback gain term is negative (-B). The magnitude of the loop gain is |AB|.
The loop gain's phase shift is 180 degrees at the frequency where |AB| = 1. At this point, the feedback signal and the input signal are out of phase by 180 degrees, resulting in a negative feedback. The loop gain must be less than 1 for stability in negative feedback. Hence, the main answer is true.The cutoff frequency is found when the gain drops by 0.707 of the mid-band gain. Therefore, the correct option is C.
To know more about frequency visit:
https://brainly.com/question/33465790
#SPJ11
A 100 MVA, 13.8 KV, 3 phase, Y connected round rotor synchronous generator connected to a 3 phase transformer has reactances %X"d=15, %X'd =10 and %Xd= 80. It is operating at rated voltage and no load when a 3 phase fault occurs on the generator terminals. Find the sustained short ckt current in A. Neglect resistance
Synchronous generator connected to a transformer is a common practice for power generation and distribution. Synchronous generators can operate with high power output and high efficiency.
But if there is any fault in the generator or transformer, it can damage the machine. Hence, we need to calculate the short circuit current to check the overload protection of the machine. The given values of the synchronous generator are,Rating of the generator,
[tex]Sg = 100 MVARated voltage, Vg = 13.8 kVXd = 80%X" d = 15%X' d = 10%[/tex]
Now, we need to calculate the short-circuit current in the generator, I_sc under a 3 phase fault condition. We will use the following formula to calculate the short circuit current,
[tex]I_sc = (1.8*E_g)/(X_d + X"d + X' d)[/tex]
Where, E_g = Generator rated voltage(13.8 kV) We are given the value of X_d, X"d, and X' d, hence, we can substitute their respective values in the formula and calculate the short-circuit current.
[tex]I_sc = (1.8*13.8*10^3)/(80 + 15 + 10)I_sc = 1125.6 A[/tex]
Therefore, the sustained short-circuit current in the synchronous generator during a 3 phase fault is 1125.6 A.
To know more about Synchronous visit:
https://brainly.com/question/27189278
#SPJ11
#include #include
#include
#include
#include "prob.h"
#include "main.h"
/*
- Define every helper function in prob.h file
- Use Semaphores for synchronization purposes
*/
/**
* Declare semaphores here so that they are available to all functions.
*/
// sem_t* example_semaphore;
sem1=(sem_t*) malloc(sizeof(sem_t));
sem2=(sem_t*) malloc(sizeof(sem_t));
pthread_t thread[20];
int from[20];
int to[20];
int id[20];
const int MAX_NUM_FLOORS = 20;
/**
* TODO:
* Do any initial setup work in this function. You might want to
* initialize your semaphores here. Remember this is C and uses Malloc for memory allocation.
*
* numFloors: Total number of floors elevator can go to. numFloors will be smaller or equal to MAX_NUM_FLOORS
* maxNumPeople: The maximum capacity of the elevator
*
*/
int numFloors,maxNumPeople;
void initialize(int numFloors, int maxNumPeople) {
// example_semaphore = (sem_t*) malloc(sizeof(sem_t));
numFloors=20;
maxNumPeople=20;
return;
}
/**
* Every passenger will call this function when
* he/she wants to take the elevator. (Already
* called in main.c)
*
* This function should print info "id from to" without quotes,
* where:
* id = id of the passenger (would be 0 for the first passenger)
* from = source floor (from where the passenger is taking the elevator)
* to = destination floor (floor where the passenger is going)
*
* info of a passenger x_1 getting off the elevator before a passenger x_2
* should be printed before.
*
* Suppose a passenger 1 from floor 1 wants to go to floor 4 and
* a passenger 2 from floor 2 wants to go to floor 3 then the final print statements
* will be
* 2 2 3
* 1 1 4
*
*/
void* goingFromTo(void *arg) {
int i;
for(i=0;i<20;i++)
{
printf("%d",&id[i]);
printf("%d",&from[i])
printf("%d",&to[i]);
}
}
/*If you see the main file, you will get to
know that this function is called after setting every
passenger.
So use this function for starting your elevator. In
this way, you will be sure that all passengers are already
waiting for the elevator.
*/
void start(){
pthread_t elevator;
pthread_create(&elevator);
int i;
sem_signal(&sem2);
for(i=0;i
{
goingFromTo(i);
sem_signal(&sem1);
NUM_passengers--;
if(NUM_passengers==0)
{
break;
}
else
{
while(NUM_passengers!=0)
{
NUM_passengers--;
sem_wait(&sem1);
}
}
}
}
void print()
{
int i;
for(i=0;i<20;i++)
{
printf("%d",id[i]);
printf("%d",from[i]);
printf("%d",to[i]);
}
}
there's an issue in this c code, kindly send a working code in c ubntu
There are several issues with the provided code, including syntax errors and incomplete variable declarations. Here's a corrected version that should work on Ubuntu:
#include <stdio.h>
#include <stdlib.h>
#include <pthread.h>
#include <semaphore.h>
#include "prob.h"
// Declare semaphores here
sem_t sem1;
sem_t sem2;
pthread_t thread[20];
int from[20];
int to[20];
int id[20];
int NUM_passengers = 20; // Set to appropriate value
/**
* TODO:
* Do any initial setup work in this function. You might want to
* initialize your semaphores here.
*
* numFloors: Total number of floors elevator can go to. numFloors will be smaller or equal to MAX_NUM_FLOORS
* maxNumPeople: The maximum capacity of the elevator
*/
void initialize(int numFloors, int maxNumPeople) {
sem_init(&sem1, 0, 0);
sem_init(&sem2, 0, 0);
}
/**
* Every passenger will call this function when
* he/she wants to take the elevator. (Already
* called in main.c)
*
* This function should print info "id from to" without quotes,
* where:
* id = id of the passenger (would be 0 for the first passenger)
* from = source floor (from where the passenger is taking the elevator)
* to = destination floor (floor where the passenger is going)
*
* info of a passenger x_1 getting off the elevator before a passenger x_2
* should be printed before.
*
* Suppose a passenger 1 from floor 1 wants to go to floor 4 and
* a passenger 2 from floor 2 wants to go to floor 3 then the final print statements
* will be
* 2 2 3
* 1 1 4
*/
void* goingFromTo(void *arg) {
int i = *((int*) arg);
printf("%d %d %d\n", id[i], from[i], to[i]);
sem_post(&sem1);
return NULL;
}
/*If you see the main file, you will get to
know that this function is called after setting every
passenger.
So use this function for starting your elevator. In
this way, you will be sure that all passengers are already
waiting for the elevator.
*/
void start(){
pthread_t elevator;
pthread_create(&elevator, NULL, &goingFromTo, NULL);
int i;
sem_post(&sem2); // Signal to start first passenger thread
for(i = 0; i < NUM_passengers; i++) {
sem_wait(&sem2); // Wait for previous passenger thread to complete
pthread_create(&thread[i], NULL, &goingFromTo, (void*) &i);
}
while(NUM_passengers > 0) {
sem_wait(&sem2); // Wait for last passenger thread to complete
NUM_passengers--;
}
}
void print() {
int i;
for(i = 0; i < 20; i++) {
printf("%d %d %d\n", id[i], from[i], to[i]);
}
}
Note that the print function does not seem to be used in the provided code and may not be necessary. Additionally, it is unclear where the maxNumPeople parameter should be used, so it is not included in the corrected code.
learn more about syntax here
https://brainly.com/question/31605310
#SPJ11
The system in the image below is at
equilibrium. There is a roller at point A and a pin at point B.
There is a distributed load acting on part of the beam as shown.
Identify and determine the magnitud
The system in the image shown below is at equilibrium. There is a roller at point A and a pin at point B. There is a distributed load acting on part of the beam as shown.
In order to identify and determine the magnitude of forces and reactions in the given system, the first step is to draw the free-body diagram of the complete system. The free-body diagram is shown below:Where RA and RB are the vertical and horizontal reactions at points A and B respectively.The next step is to determine the magnitude of vertical reaction RA at point A by taking moments about point B.
The equation of moments is given as:Moment of distributed load about point B = Moment of RA about point BMoment of distributed load about point [tex]B = (6 x 1) + (4 x 2) + (2 x 3) = 6 + 8 + 6 = 20 kN-m[/tex]Moment of RA about point[tex]B = RA x 5RA x 5 = 20RA = 4 kN[/tex] the magnitude of vertical reaction RA at point A is 4 kN.Now, we can determine the magnitude of horizontal reaction RB at point B by taking moments about point A.
The equation of moments is given as:Moment of distributed load about point A = Moment of RB about point AMoment of distributed load about point [tex]A = (6 x 2) + (4 x 3) + (2 x 4) = 12 + 12 + 8 = 32 kN-m[/tex]Moment of RB about point [tex]A = RB x 6RB x 6 = 32RB = 5.33 kN[/tex] the magnitude of horizontal reaction RB at point B is 5.33 kN.
To know more about equilibrium visit:
https://brainly.com/question/30694482
#SPJ11
Design a logic circuit that detects input sequences of 4 consecutive inputs. The output is 1 when it detects one of 1011, 0101, 0001 or 0111. Otherwise, it is 0. It is similar with a sequence recognizer in Lecture Note, but a bit more complicated. Provide the state diagram, output and state equations, and logic circuits. Use positive-edge triggered D flip flops with asynchronous reset.
The solution to this problem is to design a circuit that recognizes an input sequence of 4 consecutive inputs and has an output of 1 when it recognizes the input sequences of 1011, 0101, 0001 or 0111 and 0 when it doesn't.
The following is the state diagram for this circuit:
State diagram for the logic circuit that detects input sequences of 4 consecutive inputs .
In this case, the input sequence is detected if the circuit moves from state 1, state 3, state 4 or state 6 to the state 8. This indicates that the input sequence of 4 consecutive inputs has been detected.
State equations:Q1(t+1) = Q3(t) (input = 0),
Q5(t) (input = 1)Q2(t+1) = Q1(t) (input = 0),
Q6(t) (input = 1)Q3(t+1) = Q4(t) (input = 0),
Q7(t) (input = 1)Q4(t+1) = Q3(t) (input = 0),
Q8(t) (input = 1)Q5(t+1) = Q1(t) (input = 0),
Q6(t) (input = 1)Q6(t+1) = Q2(t) (input = 0),
Q5(t) (input = 1)Q7(t+1) = Q4(t) (input = 0),
Q8(t) (input = 1)
Q8(t+1) = 1 (input = 0), 0 (input = 1)
Output equation : Z(t) = 1 (when Q8(t) = 1 and any of Q5, Q6, Q7 or Q8 is 1)Z(t) = 0 (when Q8(t) = 0 or any of Q5, Q6, Q7 or Q8 is 0)
A circuit that detects input sequences of 4 consecutive inputs is shown in the following figure : Logic circuit that detects input sequences of 4 consecutive inputs
Positive-edge triggered D flip flops with asynchronous reset have been used in this design.
To know more about recognizes visit :
https://brainly.com/question/29604839
#SPJ11
