Explain Resistor in parallel and series.
Answers
[tex]\sf\huge\underline\blue{Resistor:-}[/tex]
[tex]\rightarrow[/tex]A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element.
[tex]\rightarrow[/tex]Resistors reduce the current flow and lower voltage levels within circuits.
[tex]\sf\large\underline\purple{Resistors \:in\: Series:-}[/tex]
[tex]\rightarrow[/tex]A circuit is said to be connected in series when the same amount of current flows through the resistors. In such circuits, the voltage across each resistor is different.
[tex]\rightarrow[/tex]In a series connection, if any resistor is broken or a fault occurs, then the entire circuit is turned off. The construction of a series circuit is simpler compared to a parallel circuit.
[tex]\rightarrow[/tex]For the above circuit(attached image-1), the total resistance is given as:
[tex]\sf{R_{total}\: = \:R1 + R2 + ….. + Rn}[/tex]
The total resistance of the system is just the total of individual resistances.
[tex]\sf\large\underline\purple{Resistors \:in\: Parallel:-}[/tex]
[tex]\rightarrow[/tex]A circuit is said to be connected in parallel when the voltage is the same across the resistors. In such circuits, the current is branched out and recombines when branches meet at a common point.
[tex]\rightarrow[/tex]A resistor or any other component can be connected or disconnected easily without affecting other elements in a parallel circuit.
[tex]\rightarrow[/tex]The figure(attached image -2) above shows ‘n’ number of resistors connected in parallel. The following relation gives the total resistance here
[tex]\sf{\frac{1}{R_{total}}\: = \:\frac{1}{R1} + \frac{1}{R2} + ….. + \frac{1}{Rn}}[/tex]
[tex]\rightarrow[/tex]The sum of reciprocals of resistance of an individual resistor is the total reciprocal resistance of the system.
_______________________________
Hope it helps you:)
Answer:
In a series circuit, the output current of the first resistor flows into the input of the second resistor; therefore, the current is the same in each resistor. In a parallel circuit, all of the resistor leads on one side of the resistors are connected together and all the leads on the other side are connected together.
Related Questions
The graph represents the relationship between the work done by a student running up a flight of stairs and the time of ascent.
I think the answer is B, I think im wrong.
Answers
Answer:
power
Explanation:
The slope would be y/x or work / time which is the definition of power
Compressed air moves through a pipe at a speed of 0.5m/s. If the diameter is 1 cm, what is the flow rate of the air
Answers
Answer:
Square the pipe's radius. With a radius, for instance, of 0.05 meters, 0.05 ^ 2 = 0.0025. Multiply this answer by the pressure drop across the pipe, measured in pascals. With a pressure drop, for instance, of 80,000 pascals, 0.0025 x 80,000 = 200.
Explanation:
I hope this helps!
7. A rocket has a weight of 30,000 N on earth. a) What is the mass of the rocket in outer space? Use appropriate calculations and arguments to support your answer.
b) Calculate the weight of the rocket on planet X (g=7.5 N/Kg)
c) What is the weight of the rocket in outer space? Provide reasons to support your answer
Answers
Explanation:
a) mass=3000kg
b) weight on planet x=3000 × 7.5
=22,500N
c) Weight in outer space will be equal to zero
since the gravity in outer space is negligible
Do people actually see me inverted?☹
Answers
Answer:
of course is clear
Explanation:
very clear
A hiker, weighing 560 newtons, takes 140 seconds to walk to the top of a hill with a height of 60 meters. How much power does the hiker develop?
A. 240 W
B. 1300 W
C. 2400 W
D. 78,000 W
Answers
Answer:
A -- 240
Explanation:
It takes around 270 to cycle more newtons up a hill
A sound travels down a hallway that is 115 m long. Then it echoes and
returns back to the source. If the speed of sound is 350 m/s, how long
does it take in seconds) to hear the echo?
Answers
Answer:
0.66 s
Explanation:
∆x = v∆t → 2 × 115 = 350 ∆t → ∆t = 230/350 = 0.66 s
A monochromatic light passes through a narrow slit and forms a diffraction pattern on a screen behind the slit. As the slit width increases, the diffraction pattern:.
Answers
As the slit width increases, the diffraction pattern gets narrower and vice versa.
Relationship between width and diffraction patternThe increase in silt width leads to the narrowing of diffraction pattern of the light because the increase of width reduces the space for the passing of light wave.
So we can conclude that as the slit width increases, the diffraction pattern gets narrower and vice versa.
Learn more about diffraction here: https://brainly.com/question/16749356
The Earth pulls on the Sun with the same magnitude force that the Sun pulls on the Earth. If these forces are equal, why does Earth go in orbit around the Sun? Why does Earth experience a great centripetal acceleration, while the Sun doesn't?
Answers
Answer:
For every force there is an equal and opposite reaction force.
For instance, if one wants to find the acceleration of a person standing on a scales, he uses the force exerted by the scales on the person,
One doesn't consider the reaction force of the person on the scales.
Likewise for the force of the sun on the earth
m v^2 / R = G M m / R^2 descibes the force acting on the earth to produce the centripetal acceleration of v^2 / R
The sun experiences the same centripetal acceleration as the earth, but since the mass of the sun is about 333,000 times the mass of the earth the acceleration can be ignored for most purposes.
When a satellite experiences an acceleration of v^2 / r, the earth is undergoing the same centripetal acceleration. However since the mass of the earth is much greater than that of a satellite and the centripetal acceleration of the earth is ignored.
a bullet of mass 50gm is moving with the velocity of 720 km / HR calculate the key of bullet
Answers
Answer:
1000 j
Explanation:
KE = 1/2 m v^2 where m is in kg and v = m/s
= 1/2 * .050 * (720 *1000/3600 )^2
why do we see optical illusion?
Answers
Optical illusions occur because our brain is trying to interpret what we see and make sense of the world around us. Optical illusions simply trick our brains into seeing things which may or may not be real.
Have a great day ;)
initial velocity 0 km/hr, final velocity 24km/hr, time 3s, what is acceleration
Answers
Answer:
8 km/hr
Explanation:
Acceleration
=Change in Velocity/ Time
=(24-0)/3
=8
The acceleration of the body is {a} = 8 km/hr².
What is acceleration?Acceleration is defined as the rate of change of velocity per unit time.
Given is -
Initial velocity : 0 km/hr
Final velocity : 24km/hr
Time : 3s
We can write the acceleration as -
a = Δv/Δt
a = (24 - 0)/(3 - 0)
a = 24/3
a = 8 km/hr²
Therefore, the acceleration of the body is {a} = 8 km/hr².
To solve more questions on acceleration, visit the link -
brainly.com/question/30098550
#SPJ2
26. Suppose you have a circuit with two lightbulbs that have the same resistance
connected in series and you have another circuit with two lightbulbs with the same
resistance connected in parallel. What would happen if you disconnected one bulb in
each circuit?
Answers
Answer:
It would break the circuit.
Explanation:
As the projectile goes upward, what energy changes take place?.
Answers
Answer:
Initial kinetic energy is transformed into potential energy.
If a bullet of mass 50 gm is moving with the velocity of 720 km/hr. Calculate its kinetic energy. Ans: here, mass (m)= 50 gm = 50/1000 kg = 0.05 kg velocity (v) = 720 km/hr= 720×1000/60×60=200m/s kinetic energy = ? We know, K.E.= 1/2 mv^2 = 1/2 × 0.05×(200)^2 = 0.05×40000/2 = 1000j ans. Is it correct???????
Answers
Answer:
yes 1000 j as I posted on the same Q elsewhere
Explanation:
Which term is used to describe the highest point on a transverse wave?
A. frequency
B. crest
C. trough
D. amplitude
Answers
Answer:
B. Crest
Explanation:
The high point of a transverse wave is a called the crest.
define physical balance
Answers
A physical balance is simply a weight measuring instrument. It is used to measure the weight of any unknown object with the help of the other object with known weight.
Explanation:
Hope it helps you!!A block is sitting on a small platform supported by a spring and is undergoing simple harmonic oscillation with a frequency of 4.5 Hz. What is the maximum amplitude at which the block will stay on the platform
Answers
For a block undergoing simple harmonic oscillation, the maximum amplitude is mathematically given as
a=0.0749m
Generally, the equation for the maximum acceleration is mathematically given as
Ma=A*w^2
Where
A = 0.075 m
Therefore
0.075 * w^2 = 9.8
w = 11.43 rad/s
In conclusion, maximum frequency
mF=w/2pi
mF=11.43/2pi
mF= 1.82 Hz
Where
g=2\pif)^2a
a=(9.8)/4*\pi^2(1.82)^2
a=0.0749m
Read more about frequency
https://brainly.com/question/24623209
Which purpose does a light bulb serve in a circuit?
Answers
Answer:
A light bulb is that component of circuit that lights up when electricity flows through it and vice versa. Its main function is to tell whether electricity is being supplied or not. Its function is also to light up dark places.
Explanation:
Answer:
A light bulb is that component of circuit that lights up when electricity flows
Explanation:
Use the passage to answer the question.
Light can be passed through two slits and projected onto a screen. The light from the two light sources produces a pattern of dark and light spots on the screen. The spots can be the result of interference, which happens with waves but not particles. This shows that the wave explanation is best for explaining the spots.
What is the reasoning in this passage?
(1 point)
Light can be passed through two slits and projected onto a screen.
The light from the two light sources produces a pattern of dark and light spots on the screen.
The spots are the result of interference, which happens with waves but not particles.
This shows that the wave particle is best for explaining the spots.
Answers
The reasoning in the passage is : ( C ) The spots are the result of interference, which happens with waves but not particles
Light wavesLight passed through a slit and projected onto a screen will form a pattern which is very visible and the pattern might have dark spots if there is some form of interference. Interference is present in waves and not particles.
Hence we can conclude that the reasoning in the passage is The spots are the result of interference, which happens with waves but not particles
Learn more about light waves : https://brainly.com/question/25847009
The photograph shows a kettle made of the element copper. Which statement describes a chemical property of copper?
A. Copper forms a patina when it interacts with air.
B. Copper is a solid at room temperature.
C. Copper is a good conductor of electric current.
D. Copper can be re-shaped when hit with a hammer.
Answers
Explanation
B describes its matter (composition)
C describes its ability to conduct
D describes is mailability
A describes a chemical reaction with the air
5. The amount of energy provided by a battery in a circuit is
the amount of energy consumed in the circuit.
A. Equal to
B. Less than
C. Greater than
D. Not related to
Answers
the amount of energy consumed in the circuit.
C. Greater than
Which force is responsible for holding the nucleus together via gluons.
Answers
One end of a copper rod is placed in a flame of a Bunsen burner. Small pieces of wax placed along the rod melt at progressively larger distance from the flame. Heat is transferred through the rod by ________.
1) Convection
2)Radiation
3)Conduction
Answers
Conduction is the process of heat transferring from a region of hotter temperature to a region of colder temperature through a material or substance by its atoms or molecules transferring heat energy to each other through collision
Hope this helps
Answer:
3) Conduction
Explanation:
When heat is transferred through a material, it can be referred to as conductionThe wax on the rod can only melt by the rod only if it is in contact with itA 430 kg piano is to be slid up a 3.5 m frictionless plank at a constant speed. The plank makes an angle of 30° with the horizontal. Calculate the work done by the person sliding the piano up the plank.
Answers
Answer:
10628.87 1
Explanation:
What do we mean by the diffraction limit of a telescope?.
Answers
Answer:
Diffraction Limit. The angular resolution that a telescope could achieve if it were limited only by the interference of light waves; it is smaller (i.e., better angular resolution) for larger telescopes.
Explanation:
Searched it up
Questions #11, 12, and 13:
Part 1 of 3: 2.4 cm³ of water is boiled at atmospheric pressure to become 4514.7 cm³ of steam, also at atmospheric pressure. Calculate the work done by the gas during this process. The latent heat of vaporization of water is 2.26 × 10⁶ J/kg. Answer in units of J.
Part 2 of 3: Find the amount of heat added to the water to accomplish this process. Answer in units of J.
Part 3 of 3: Find the change in internal energy. Answer in units of J.
Answers
During the isobaric expansion;
work done by the gas is 457.2 Jheat absorbed by the water is 4520 Jthe change in internal energy of a system is 4062.8 J.What is the work done by a gas in an isolated process?The work done by a gas in an isolated expansion is the product of pressure and change in volume.
[tex]W = p\times \Delta V[/tex]
1 atm = 101325 Pa
2.4 cm³ = 2.4 × 10^-6 m³
4514.7 cm³ = 4514.7 × 10^-6 m³
[tex]W = 101325 Pa \times (4514.7\times 10^{-6} m^3 - 2.4\times10^{-6} m^3) = 457.2 J \\ [/tex]
Thus, work done by the gas is 457.2 J
Tje Heat absorbed by the water during vaporization process is calculated using the formul:
Q = m×ΔHvapmass of water = density × volume
mass of water = 1 g/cm³ × 2.4 cm³ = 2 g = 0.002 kg
Q = 0.002 kg × 2.26 × 10⁶ J/kg
Q = 4520 J
Thus, heat absorbed by the water is 4520 J
The change in internal energy, ΔU of a system is given as the heat absorbed minus the work done by the system.
[tex]\Delta U = Q-W [/tex]
ΔU = 4520 J − 457.2 J = 4062.8 J
Therefore, the change in internal energy of a system is 4062.8 J.
Learn more about change in internal energy at: https://brainly.com/question/14126477
conventionally anti clock wise torque is taken as?
Answers
Answer:
An anti-clockwise movement is taken as a positive and a clockwise moment is taken as a negative.
Why is the speed of different sounds in a single medium remain the same though wavelength is different?
Answers
Answer:
I think it's because the refractive index of that medium is constant
How many times has the Sun orbited around the Milky Way since the Sun first formed, if the Sun makes one orbit every 231 million years
Answers
Answer:
It would depend on the amount of years.
Explanation:
I don’t think this is very helpful-
Have a great day!
Anygays-
Help!!
Hurry!!!?!?!?
I don't know!!!!!
Answers
Answer:
KE = 1/2 M V^2 = 35 kg / 2 * (10 m/s)^2
KE = 17.5 * 100 kg m^2 / s^2 = 1,750 Joules
(B) is the correct answer
