"If a vector pointing to the right has a positive magnitude, then one point to the left has a negative magnitude " is a false statement.
Vector, in physics, a quantity that has both magnitude and direction. This is usually represented by an arrow whose direction is the same as the quantity and whose length is proportional to the magnitude of the quantity. A vector has magnitude and direction, but no position. In other words, the vector does not change with translation unless the length changes.
Reason :
Because magnitude is never negative, only direction may be negative or positive.
Learn more about Vector here :-
brainly.com/question/18660017
#SPJ4
When a person sits in a chair they apply a force to the chair the chair?; When you sit in a chair your body exerts a downward force on the chair What is the reaction force?; What would happen if a person sat on a chair and the chair did not exert an equal force back?; Why is it that if you sit on a chair you do not fall to the ground?
When you sit on the chair, your body will exert a downward force and in reaction, the chair pushes up on your body.
What is a Reaction Force?
A building experiences a reaction force when it rests against another object. Calculating the reaction forces at the supports as a result of the forces operating on the beam is a necessary step in the analysis of a beam structure. The reaction forces can be calculated using a free body diagram of the entire beam.
Corrosion can be caused by reaction forces. For instance, due to the system's increased stiffness, reaction forces increase when bearing clearances are reduced from 350 mm to 150 mm.
According to the question, when the body will exert a downward force that is mg due to gravity, the chair will make a normal reaction force which will be equal to the force applied by the body on the chair.
Learn more about Reaction Force here :-
brainly.com/question/14853868
#SPJ4
As the text discusses the conservation of linear momentum is applicable only when the system of objects is an isolated system. Which of the systems listed below are isolated systems? 1) A ball is dropped from the top of a building. The system is the ball. 2) A ball is dropped from the top of a building. The system is the ball and the earth. 3) A billiard ball collides with a stationary billiard ball on a frictionless pool table. The system is the moving ball. 4) A car slides to a halt in an emergency. The system is the car. 5) A space probe is moving in deep space where gravitational and other forces are negligible. The system is the space probe. O 3&5 O 1 & 3 O2 O 2 & 5 O 2 & 4
The correct answer for the isolated systems is options 2 & 4.
2) A ball is dropped from the top of a building. The system is the ball and the earth.
4) A car slides to a halt in an emergency. The system is the car.
In both of these systems, the isolated system is the object in motion, either the ball dropped from the top of the building or the car sliding to a halt in an emergency. The conservation of linear momentum is applicable because the system does not interact with any external forces or objects.
For more questions like Isolated system click the link below:
https://brainly.com/question/14434076
#SPJ4
Find the kinetic energy KKK of the block at the moment labeled B.
Express your answer in terms of kkk and AAA.
The kinetic energy KKK of the block at the moment labeled B is 3/8kA^2.
Kinetic energy is the energy that an object possesses due to its motion. It is defined as the work required to accelerate a body of specified mass from rest to a specified velocity. After the body acquires this energy during acceleration, it retains this kinetic energy as long as the velocity does not change.
Kinetic energy is the energy a body has due to its motion. If you want to accelerate an object you have to apply a force. To add strength, we need our work. When the work is done, the energy is transferred to the object and it moves at a new constant speed.
Learn more about Kinetic energy here:- https://brainly.com/question/25959744
#SPJ4
In searching the bottom of a pool at night, a watchman shines a narrow beam of light from his flashlight, 1.3 m above the water level, onto the surface of the water at a point d = 2.9 m from his foot at the edge of the pool Where does the spot of light hit the bottom of the h = 2.2 m deep pool? Measure from the bottom of the wall beneath his foot. Express your answer to two significant figures and include the appropriate units.
The spot of light hit the bottom of the h = 2.2 m deep pool will hit the bottom at 4.98 m away.
Here ,
height h = 2.2 m
h1 = 1.3 m
d = 2.9 m
let the distance of spot where light hit bottom from side is l
angle of incidence , i = arctan(2.9/1.3)
i = 65.9 degree
Using Snell's law
1 * sin(i) = 1.33 * sin(r)
1 * sin(65.9) = 1.33 * sin(r)
r = 43.4 degree
Now , tan(r) = (l - 2.9)/h
tan(43.4 degree) = (l - 2.9)/2.2
solving for x
l = 4.98 m
the spot Light will hit the bottom at 4.98 m away
Learn more about Light here:
https://brainly.com/question/15200315
#SPJ4
a distortion of the shape of four-dimensional spacetime. a distortion of the shape of three-dimensional space. a force that acts through the action of photons at the speed of light. a force that acts through the action of gravitons that travel instantaneously.
Just as waves spread out when a boat moves in water or a stone is thrown in a pond, gravitational waves are distortions in the curvature of space-time caused by motions of matter that propagate with the speed of light.
It turns out that one type of gluon chain behaves in the four-dimensional spacetime as the graviton, the fundamental quantum particle of gravity. In this description, gravity in four dimensions is an emergent phenomenon arising from particle interactions in a gravityless, three-dimensional world.
Since matter carries energy, such objects will have a gravitational field and so they will distort space-time. So one way in which a charge or a magnet will distort space-time is by virtue of its matter.
Learn more about gravitational waves here:- https://brainly.com/question/13045752
#SPJ4
A charged insulator can be discharged by passing it just above a flame. This is because the flame
A warms it
B dries it
C contains carbon dioxide
D contains ions
Passing an insulator just over a flame will cause it to discharge if it is charged. This is due to the presence of ions in the flame.
The Correct Answer is D.
What does a ion contain?An atom is referred to as an ION when it is drawn to another atom as a result of having an uneven number of protons and electrons. It is referred to be an anion or a negative ion if the atom contains more electrons than protons. An ion is a positive ion if it has more protons than electrons.A solution that typically has ions—atoms or molecules that have received or lost electrons—and is electrically conductive is referred to as an electrolyte solution. However, there are some situations when the electrolytes are not ions, despite the fact that they are frequently referred to as ionic solutions for this reason.To Learn more About ions refer To:
https://brainly.com/question/13692734
#SPJ4
The velocity, , of an object that falls freely due to the Earth gravity can be modeled with the equation: m dv/dt = -mg + kv^2
where m is the mass of the object, g = 9.81 m/s^2, and k is a constant. Solve the equation for v for the case that m = 5 kg, k = 0.05 kg/m, 0
V=√1962 tan h (-√1962t/100) is the velocity of the object that is falling freely due to earth's gravity.
What is Newton second law of motion?The second law states that the acceleration of an object is dependent upon two variables - the net force acting upon the object and the mass of the object.
According to Newton's second law of motion,
mdv/dt= -mg+kv²
Calculation:mdv/dt=-mg+kv²
5dv/dt=-10g+0.05v²
dv/dt=-2×9.81×0.01v²
dev/dt=0.01v²-19.62
-1/19.62 dv/dt =1-v²/1962
-1/19.62 ∫dv/1-v²/1962=∫dt
√1962 Tanh∧-1 (v/√1962)=-19.62t
Tanh∧-1(v/√1962)=-√1962/100 t
v=√1962 Tan h∧-1 (-√1962t/100)
To know more about Newton's second law of motion, click on https://brainly.com/question/25545050
#SPJ4
A steel ball of mass 0.500 kg is fastened to a cord that is 70.0 cm long and fixed at the far end. The ball is then released when the cord is horizontal (Fig 9-65). At the bottom of its path, the ball strikes a 2.50 kg steel block initially at rest on a frictionless surface The collision is elastic. Find
(a)the speed of the ball and (b) the speed of the block, both just after the collision.
(a) ball velocity = - 2.47 m/s
(b) block velocity = 1.236 m/s
What is collision?Two items collide when they briefly come into touch with one another. To put it another way, a collision is a brief reciprocal encounter between two masses in which the momentum and energy of the masses change.
For ball as it is at initially at height of 70.0 cm = 0.7 m
so by energy conservation,
K.E.(i) P.E.(i) + K.E.(f)+P.E.(f)
0 + mg×(0.7) = 1/2 mv² + 0
v = 3.71 m/s
now, collision b/w ball and block
as the block is in rest initially and there is no external force b/w them
so by momentum conservation,
m₁u₁+ m₂u₂ = m₁v₁+ m₂v₂
or, (0.5 x 3.71) + 0 = (0.5x v₁) + (2.5 x v₂)
3.71 = v₁ + 5v₂ .........(1)
as elastic collision so energy conservation
or, 1/2 m₁ u₁² + 1/2 m₂ u₂² = 1/2 m₁ v₁² + 1/2 m₂ v₂²
or, (1/2 x 0.5 x 3.712) + 0 = (1/2 x 0.5 x v₁²) + (1/2 x 2.5 x v₂²)
or, 3.433 = 0.25xv₁² + 1.25 v₂² ...............(2)
from eq. 1 and eq. 2
or, 3.433 = 0.25 x (3.71 - 5 v₂)² + 1.25v₂²
or, v² = 1.236 m/s
and v₁ = 3.71 - 5v₂
or, v₁ = - 2.47 m/s
so after collision
ball velocity = - 2.47 m/s [(-)ve x direction]
block velocity = 1.236 m/s [(+)ve x direction]
To know more about velocity refer to:
https://brainly.com/question/24445340
#SPJ1
What is the frequency of a red light( red light has a wavelength of 700 nanometers ) ( 1 nanometer: 1*10^9 meters)
When the wavelength is 700 NM, the frequency of red light is 4.29 x 1014 Hz.
What frequency is red light with a 700 nm wavelength?For instance, visible red light with a wavelength of 700 nm has a frequency of 4.29 x 1014 Hz and an energy of 2.84 x 10-19 J or 171 kJ per mole of photons (note that Avogadro's number is 6.02 1023 mol1).
How often does 700 occur?A significant portion of the spectrum that is available for both commercial wireless and public safety communications is the 700 MHz Band. The Band, which spans 108 megahertz of spectrum from 698 to 806 MHz, was created as a result of the switch to digital television.
To know more about wavelength visit:-
https://brainly.com/question/13533093
#SPJ1
you cut one of these plasmids simultaneously with enzymes a and b, and obtain the following gel (cut product loaded in lane 1): Which plasmid is it that you cut?A. Plasmid 1B. Plasmid 2C. Plasmid 3D. Plasmid 4
The cuts on the plasmid are done via restriction enzymes which are also known as molecular scissors. (B) Plasmid 2 is the one that got cut by the restriction enzyme.
What is the Plasmid?A plasmid is a type of double-stranded, circular, tiny DNA molecule that differs from a cell's chromosomal DNA. Both bacterial and certain eukaryotic cells naturally contain plasmids. Plasmids frequently carry genes that give bacteria genetic advantages like antibiotic resistance.
What is the Restriction enzyme?An isolated bacterial protein known as a restriction enzyme cleaves DNA at sequence-specific locations to create DNA fragments with a known sequence at each end. For several laboratory techniques, such as genetic engineering and recombinant DNA technologies, restriction enzymes are essential.
Hence, the cuts on the plasmid are done via restriction enzymes which are also known as molecular scissors. (B) Plasmid 2 is the one that got cut by the restriction enzyme.
To know more about Restriction enzymes, check out:
https://brainly.com/question/1127662
#SPJ4
Based on the number of galaxies visible in the Hubble eXtreme Deep Field (Figure 16.1 in your text), the estimated number of galaxies in our observable universe is at least ______.100 million50,000100 billioninfinity
Based on the number of galaxies visible in the Hubble eXtreme Deep Field, the estimated number of galaxies in our observable universe is at least 100 billion.
The Hubble eXtreme Deep Field contains an estimated 10,000 galaxies, representing a tiny fraction of the estimated 100 billion galaxies that make up our observable universe. Beyond that, the universe is thought to be infinite, making the total number of galaxies impossible to count.
Therefore the correct option in this question is C which is 100 billion.
For more questions like Galaxies click the link below:
https://brainly.com/question/29589933
#SPJ4
7. The vectors d &e are [- 4, 1] \&[1,4] respectively. Find the angle b/n d&e( use dot product)
Answer:
90° or π/2 rad
Explanation:
Given two vectors:
[tex] \displaystyle{ \vec d = - 4 \hat i + \hat j} \ \: \text{and} \ \: \displaystyle{ \vec e = \hat i + 4 \hat j}[/tex]
We can find the angle by applying dot product:
[tex] \displaystyle{ \vec d \cdot \vec e = | \vec d| | \vec e| \cos \theta}[/tex]
Find magnitude of two vectors:
[tex] \displaystyle{ | \vec d| = \sqrt{ {( - 4)}^{2} + {1}^{2} }} \\ \\ \displaystyle{ | \vec d | = \sqrt{16 + 1} = \sqrt{17} }[/tex]
And
[tex] \displaystyle{ | \vec e| = \sqrt{ 1^{2} + {4}^{2} }} \\ \\ \displaystyle{ | \vec e | = \sqrt{1 + 16} = \sqrt{17} }[/tex]
Thus, we now have:
[tex] \displaystyle{ \vec d \cdot \vec e = \sqrt{17} \cdot \sqrt{17} \cos \theta} \\ \\ \displaystyle{ \vec d \cdot \vec e = 17 \cos \theta}[/tex]
Product of two vectors are:
[tex] \displaystyle{ \vec d \cdot \vec e = d_xe_x + d_ye_y}[/tex]
Therefore:
[tex] \displaystyle{( - 4)(1) + (1)(4) = 17 \cos \theta} \\ \\ \displaystyle{ - 4 +4= 17 \cos \theta} \\ \\ \displaystyle{0= 17 \cos \theta} \\ \\ \displaystyle{0 =\cos \theta}[/tex]
Therefore, the angle would be 90° or π/2 since we know that cos90° = 0.
❧ What are Convex Mirrors?
❧ What are Concave Mirrors?
Answer:
Spherical mirrors whose inner side is reflecting are called concave mirrors. Spherical mirrors whose outer side is reflecting are called convex mirrors.
Explanation:
a spring scale shows a net force of 0.8 n acting on a 1.5-kg mass. what happens to the acceleration of the object if the net force is decreased to 0.2 n?(1 point)
Answer:
0.4m/s²
Explanation:
force = 0.8–0.2 = 0.6N
mass = 1.5kg
acceleration = ?
force = mass × acceleration
f = m × a
a = f/m
a = 0.6/1.5
a= 0.4 m/s²
rate as brainliest
Question: A nuclear power plant operates at 71 % of its maximum theoretical (Carnot) efficiency between temperatures of 635 ∘C and 300 ∘C.
If the plant produces electric energy at the rate of 1.2 GW , how much exhaust heat is discharged per hour? Express your answer using two significant figures.
If the plant produces the electrical energy at the rate of 1.2 GW then the exhaust hear discharged per hour will be 73280 Giga Joule.
What is Electrical energy?When put in an electromagnetic field, charged matter experiences a force due to the fundamental property of electric charge. Positive or negative electrical ions are possible.
When two charges are in opposition to one another, they repel one another. The term "neutral" refers to an object that has no net charge.
As per the given information in the question,
Temperature, T(L) = 300 °C
Temperature, T(H) = 635 °C
Use the equation of efficiency of the Carnot engine,
1 - T(L)/T(H) = 1 - 300/635
= 0.52
The energy produced is 1.2 GW.
This energy accounts for 75% of all theoretically created energy.
Assume that the total energy produced by the plant is x.
x × (71/100) = 1.2
x = 1.69 GW
So, the energy lost = 1.69 - 1.2 = 0.49 GW
Assume the total heat provided is y.
0.52 × y = 1.69GW
y = 3.2 GW
So, the energy lost in the engine = 3.2 - 1.69 = 1.56
So, total energy loss = 1.56 + 0.49 = 2.05 GW or,
2.05 × 60 × 60 = 73280 Giga Joule.
To know more about Electrical energy:
https://brainly.com/question/16182853
#SPJ1
a large goose lands in a lake and bobs up and down for a short time. a fisherman notices that the first wave crest created by the goose reaches the shore 8.6 ss after the goose first contacts the water. the distance between two wave crests is 75 cmcm, and in 1.8 ss he sees four wave crests hit the shore.
The shore the goose landed 11.85m
Briefly:-For development of this problem we must resort to concepts of the basic kinematic equations that define the distance of a body, such as speed for a certain time, that is,
D=v*t
From the information is provided say that the distance between the cretas is= 0.6m,
Dcrets= .06m
In our information we have also that length between the first and the latest wave is in time terms of 2.2s. They are 4 waves in 3 intervals then
Dt= Dcrets*3= 2.4m
t= 1.6s
V= Dt/t
V= 1.5 m/s.
Then the distance from the shore is given by the speed of the waves for the total time. That is
X= v*t=11.85
the shore the goose landed X=11.8m
To know more about kinematic equation visit:-
https://brainly.com/question/28712225
#SPJ4
calculate the total impedance of the circuits in fig. 123. express your answer in rectangular and polar forms
a)6.8 + j8.2 ohms=10.65(50.33 deg) ohms
b)12-j6 ohms=13.41(-26.57 deg) ohms
c)6.6+j10 kohms=11.98(56.575 deg) ohms
RECTANGULAR FORMS
a) 6.8+j8.2 ohm
b)12-j6 ohm
c) 6.6+j10 kohm
POLAR FORMS
a) 10.65 angle 50.332 deg
b) 13.416 angle -26.565 deg
c) 11.982 angle 56.575 deg
Impedance, sometimes referred to as a "AC circuit," is the resistance to electricity passing through a circuit that uses an alternating current. Impedance, which is measured in Ohms, is the result of the combined action of the circuit's current-limiting elements, such as Resistance (R), Inductance (L), and Capacitance (C) (C).
The resistance to current flow in a Direct Current (DC) circuit is known as impedance, but in an AC circuit, impedance is the consequence of both the resistive (R) and reactive (X) components of the circuit. A DC circuit's electrical resistance is indicated by the letter "R," but an alternating AC circuit's resistance to current flow is indicated by the letter or symbol "Z."
Learn more about Ohms here:
https://brainly.com/question/2141402
#SPJ4
(01.03 MC)
An object is moving 10 m/s to the south. After one minute, its moving at a rate of 15 m/s. Explain what type of motion this is describing. Then explain
whether this represents a scalar or vector quantity.
The type of motion that is being described is linear motion and it is vector quantity because it has direction.
What is linear type of motion?
A linear motion is a type of motion in which the displacement of the object is directly proportional to the speed and time of motion of the object.
Also this type of motion occurs in a straight line.
The formula for final velocity in a linear type of motion is given as;
v = u + at
where;
v is the final velocity of the objectu is the initial velocity of the objecta is the acceleration of the objectt is time of motion of the objectFrom the given statement, our equation becomes;
15 m/s = 10 m/s + 60a
Thus, the above equation shows final velocity formula which is a vector quantity.
Learn more about final velocity here: https://brainly.com/question/25905661
#SPJ1
what is the total work wfric done on the block by the force of friction as the block moves a distance 7.00 m up the incline?
The total work done on the block by the force of friction is 14 J.
What is what done by friction force?The work done by a force of friction is obtained from the product of the force of friction and the displacement of the object.
Mathematically, the work done by force of friction is given as;
W = Fd
where;
F is the force of frictiond is the displacement of the objectThe given parameters include;
force of friction = 2 Ndisplacement of the block = 7 mThe total work done on the block by the force of friction is calculated as;
W = 2 N x 7 m
W = 14 J
Learn more about work done here: https://brainly.com/question/25816840
#SPJ1
The complete question is below:
what is the total work wfric done on the block by the force of friction of 2 N as the block moves a distance 7.00 m up the incline?
match the terms with their definitions. matchtermdefinition instantaneous speeda) total distance covered divided by the total time required average speedb) rate of change of velocity with time accelerationc) rate of change of distance with time speedd) speed at a particular instant of time
Option B and C is the answer, A car's speedometer provides information about the vehicle's current instantaneous speed. It displays your speed at a certain point in time.
The speed of an item at a specific time is its instantaneous speed. The instantaneous velocity is obtained by adding the direction to the speed. In other words, this person's instantaneous velocity at that specific time was eight meters per second to the right. The speedometer on a car displays the vehicle's instantaneous speed since it does so while it is driving.
The complete question is :
which letter(s) of the sentences that are true of instantaneous speed?
a. Instantaneous speed is the total distance covered divided by
time.
b. Instantaneous speed is the speed at any instant.
c. The speedometer on a car shows the instantaneous speed.
d. If you traveled 30 kilometers in 1 hour, your instantaneous
speed would be 30 km/h.
learn more about instantaneous speed here:
https://brainly.com/question/1222392
#SPJ4
A pulse of electromagnetic radiation is propagating in the negative y-direction. You have two devices that can detect electric and magnetic fields. You place detector #1 at location {eq}\rm \langle 0, 4, 0 \rangle \ m {/eq} and detector #2 at location {eq}\rm \langle 0, -4, 0 \rangle \ m {/eq}.(a) At time t = 0, detector #1 detects an electric field in the negative x-direction. At that instant, what is the direction of the magnetic field at the location of detector #1?(b) At what time will detector #2 detect electric and magnetic fields?
The following approaches describe how electromagnetic waves travel from the transmitter antenna to the receiving antenna: ground swells Ground wave propagation is the term for electromagnetic wave propagation that occurs along the surface.
What devices that can detect electric and magnetic fields?As a result, electromagnetic waves can be generated by allowing an alternating current to pass through a wire, or an antenna.
Therefore, The X axis represents spatial distance, and the Y axis represents amplitude. An oscillating magnetic field and an adjacent oscillating electric field make up electromagnetic waves.
Learn more about magnetic field here:
https://brainly.com/question/14848188
#SPJ1
you can improve the efficiency of a program by leaving a loop as soon as a match is found in the array. True or false
A program's efficiency can be increased by exiting a loop as soon as a match is discovered in the array.The given statement is true
What is programs efficiency?
The cost of producing goods or services in comparison to other programs or an ideal procedure is referred to as program efficiency. Analyzing expenses such as money, people, time, materials, etc. is related to cost effectiveness.
Program efficiency is the cost of producing goods or services in relation to other programs or an ideal technique. Cost effectiveness is related to the analysis of expenses such as cash, people, time, and materials, among other things.
To learn more about programs efficiency visit:https://brainly.com/question/29491302
#SPJ4
to construct a nonmechanical water meter, a 0.500-t magnetic field is placed across the pipe supplying water to a home, and the hall voltage between the ends of a pipe diameter perpendicular to the field is measured. this works, because water contains ions, which are charged particles and move at the flow speed of the water.
Required:
a. Find the flow rate through a 3.00-cm-diameter pipe if the Hall voltage is 60.0 mV.
b. What would the Hall voltage be for the same flow rate through a 10.0-cm-diameter pipe with the same field applied?
The flow rate and hall voltage of non mechanical water meter is 0.339m/s and 1592.3volt respectively.
Flow rate equations depends on intensive study of fluid mechanics.
a]. flow rate =V/B x A= 60/0.500 x 3.14 x 0.03²=0.339m/s
V is hall voltage , B is magnetic field and A is cross sectional area.
The Hall effect principle describes the behavior of charge carriers when exposed to electric and magnetic fields. This principle can be viewed as an extension of the Lorentz force, which is the force acting on charge carriers (electrons and holes) passing through a magnetic field.
The Hall effect principle states that when a conductor or semiconductor is introduced with current flowing in a direction perpendicular to the magnetic field, voltage can be measured perpendicular to the current path.
b]. V=M/A=0.500/(3.14 x 0.01²) =1592.3volt
The effect of obtaining a measurable voltage as described above is called the Hall effect.
Hall voltage is directly proportional to the currentHall voltage is directly proportional to the applied magnetic field.To study about charge carriers -
https://brainly.com/question/21503713
#SPJ4
determine the mass moment of inertia of the thin plate about an axis perpendicular to the page and passing through point o . the material has a mass per unit area of 28 kg/m2 . (figure 1)
The mass moment of inertia of the thin plate about an axis perpendicular to the page and passing through point O is 0.113kgm^2
Two sections of the plate are possible. Segment (2) should be viewed as a negative part because it is a hole. The perpendicular distances from each segment's center of mass to point O are also shown.
The formula used to calculate the moment of inertia of segments (1) and (2). is Mass Moment of Inertia
m1 = π(0.2^2)(28) = 3.51kg
m2 = (0.2)(0.2)(28) = 1.12 kg
The parallel-axis theorem can be used to calculate the plate's moment of inertia for each segment along an axis perpendicular to the page and passing through point O.
I = ΣI' + md^2
I = [1/2x(3.51)x(0.2 )^2+3.51x(0.2 )^2]–[ 1/12x(0.8)x(0.2^2 + 0.2^2)+0.8x(0.2)^2]
I = 0.113kg⋅m^2
To learn more about moment of inertia click here https://brainly.com/question/15246709
#SPJ4
complete the following statement using the choices below. air moves out of the lungs when the pressure inside the lungs is . group of answer choices less than the pressure in the atmosphere equal to the pressure in the atmosphere greater than the intra-alveolar pressure greater than the pressure in the atmosphere
Air moves out of the lungs when the pressure inside the lungs is greater than the pressure in the atmosphere equal to the pressure in the atmosphere less than the pressure in the atmosphere greater than the pressure in the atmosphere greater than the intra-alveolar pressure.
When a force is applied to a substance's limits in a given amount of space, it is known as pressure. Newton per square meter, sometimes known as a pascal, is the accepted SI unit for pressure (Pa). Mathematically:
p = F/A
where
the pressure, p
F is the standard force.
The boundary's surface area is A.
In most cases, a substance's molecules colliding with the system's borders is what produces pressure, also known as the force applied per unit area to a substance's boundaries. The walls attempt to move outward as a result of the pressures that molecules try to push upon impact with them. The pressure that a system puts on its surroundings is brought about by the forces generated by all of these encounters. applying intense pressure.
Learn more about pressure here:
https://brainly.com/question/12473337
#SPJ4
if the molecular mass of a gas increases by a factor of 4 at constant temperature, its rms speed will
if the molecular mass of a gas increases by a factor of 4 at constant temperature, its rms speed is decrease by a factor of 2.
The mass of a given molecule is its molecular mass (m), which is expressed in Daltons. Because they contain various isotopes of an element, multiple molecules of the same substance can have distinct molecular weights. According to IUPAC, the related quantity relative molecular mass is a unitless comparison between the mass of a molecule and the unified atomic mass unit (also called the Dalton).. The molar mass, which is stated in g/mol, is defined as the mass of a specific material divided by the amount of a substance.As a result, the molecular mass is the mass of a single particle or molecule, while the molar mass is the average of numerous particles or molecules. When discussing macroscopic (weigh-able) amounts of a substance, the molar mass is typically the most relevant number.
To know more about molecular mass
https://brainly.com/question/29728147
#SPJ4
Part A
Consider the situation in the figure below, where two charged rods are placed a distance d on either side of an aluminum can. What does the can do?
View Available Hint(s)
Rolls to the left
Stays still
Rolls to the right
Part B
Now, consider the situation shown in the figure below. What does the can do?
Stays still
Rolls to the left
Rolls to the right
Part C
Using the setup trom the first question, imagine that you brielly touch the negatively charged rod to the can. You then hoid the two rods at equal distances or either side of the can. What does the can do?
View Avallable Hint(s)
Rolls toward the positively charged rod
Does not move
Rolls away from the positively charged rod
a) The can stays still
b) The can stays still
c) The can moves towards the positive rod
What is electrostatic force?We know that the electrostatic force is the force that attracts an object is the force that induces a charge on an object even though the objects do not touch each other. In all the cases that are shown in the images there is no contact between the charged bodies and the can.
In all the cases, we see that immediately the charged object is brought around the can, the object would cause the the electrons that are in the can to become polarized. It is the polarization of the electrons that are in the can that would make the can to move.
The movement of the can would be with reference to the kind of charges that are on the surrounding rods as well as the charges that are on the rods that have been brought around the can.
Learn more about electrostatic force:https://brainly.com/question/9774180
#SPJ1
TRUE/FALSE. g if a body is rolling on another body, the friction force required is less than or equal to je'n the relative velocity of the points in contact is zero the linear and angular motions of a cylinder are constrained by one another the friction force leads to loss of energy
It is true that the needed friction force when one body is rolling over another body is zero in both angular and linear motion if the relative velocity of the points in contact is less than or equal to that value.
When one body slides through a surface, friction acts as a repelling force. The contact between two surfaces is what causes friction. The passage of things through a surface is not smooth if there is a lot of friction. Throughout this motion, kinetic energy is converted to thermal energy. The rate of change in an object's position relative to a frame of reference is called velocity, and it depends on time. An object's speed and direction of motion are specified by its velocity.
Learn more about motion here
https://brainly.com/question/22810476
#SPJ4
What will be the gravitational force between two objects if?; What happens to the force of gravitational attraction between two small objects?; When the masses of two bodies are very small the gravitational force between them is?; Is the gravitational force between two objects the same?
The gravitational pressure among two objects is f
F=(Gm1, m2) /r^2 so force here is immediately proportional to the mass.
Since the gravitational force is inversely proportional to the rectangular separation distance between the two interacting gadgets, more separation distance will result in weaker gravitational forces. in order for two gadgets to be separated from every other, the force of gravitational enchantment between them also decreases.
The pressure of gravity relies upon without delay loads of the 2 objects, and inversely the rectangular gap between them. which means that the force of gravity increases with mass, but decreases with growing distance among gadgets.
Learn more about mass here
https://brainly.com/question/19385703
#SPJ4
You put on sunglasses and looks at the outside view. The sky is a little dark, but the reflection from a pond is much darker. Why?
A. Pond reflection is polarized
B. The light outside has changed.
C. Sunglasses are not polarized.
D. Skylight is polarized.
When you put on sunglasses and looks at the outside view, the sky is a little dark, but the reflection from a pond is much darker because Pond reflection is polarized. Option (A) is correct.
What is polarization?In the field of physics, polarization is referred to as a phenomena brought on by the fact that electromagnetic radiation is a wave.
Moving across space, electric and magnetic fields interact to form light. Light waves vibrate electrically and magnetically in perpendicular to one another. The magnetic field and electric field both move perpendicular to one another in different directions.
As a result, the direction of motion is perpendicular to both the plane occupied by the electric field and the plane of the magnetic field that is perpendicular to it.
These magnetic and electric vibrations can take place on a variety of planes. Unpolarized light is a type of light wave that vibrates in more than one plane. The sun, a lamp, and a tube light are all examples of unpolarized light sources.
Learn more about polarization here:
https://brainly.com/question/29217577
#SPJ1
