Answer:
625 GIVE ME BRAINLIEST ANSWER PLEASE
Explanation:
This question is based on pascal's Law.
So By Pascal's Law
=
therefore =force on input piston =200N
= Force on output piston = 5000N
therefore after putting the values we get,
a) = (25x 5000)/200
= 625
b) area of the salve piston = = 625
so = 625/3.14 = 199
so r = = 14.10 cm
Physics - Electricity and Magnetism
A ceiling fan operates at three speeds, using 120 V of electricity from the wall. At low speeds, it uses 0.25 A. Calculate the resistance needed to generate that current. Then in 1-2 sentences, describe how the resistance would change at medium and high speeds if larger currents are needed at those speeds. Your answer should include the calculated resistance and a sentence describing your reasoning.
Answer:
480 Ohms for the calculations
Explanation:
For the calculations:
V = 120 and I = 0.25
V = IR
R = V/I
R = 120/0.25
R = 480 Ohms
For the sentences, I am so sorry, I do not have them yet!
I. The resistance which is needed to generate a current of 0.25 Ampere in the ceiling fan is 480 Ohms.
II. Since current is inversely proportional to the resistance in the electrical circuit, an increase in the current (larger currents) flowing into the electrical circuit of the ceiling fan would cause the resistance to decrease in magnitude at medium and high speeds.
Given the following data:
Voltage = 120 VoltsCurrent = 0.25 AmpereTo calculate the resistance needed to generate that current, we would apply Ohm's law:
Ohm's law states that at constant temperature, the current flowing through an electrical circuit is directly proportional to the voltage (potential difference) applied across the two terminals of the electrical circuit and inversely proportional to the resistance in the electrical circuit.
Mathematically, Ohm's law is given by the formula;
[tex]V=IR[/tex]
Where;
V is the voltage measured in Volts.I is the current measured in Ampere.R is the resistance measured in Ohms.Making R the subject of formula, we have:
[tex]R =\frac{V}{I}[/tex]
Substituting the given parameters into the formula, we have;
[tex]R=\frac{120}{0.25}[/tex]
Resistance, R = 480 Ohms
Since current is inversely proportional to the resistance in the electrical circuit, an increase in the current (larger currents) flowing into the electrical circuit of the ceiling fan would cause the resistance to decrease in magnitude at medium and high speeds.
In conclusion, the larger the current, the lower the resistance would be at both medium and high speeds.
Read more on resistance here: https://brainly.com/question/23754122
Why does the blue force have a negative sign?
-20 N
50 N
Because 50 is smaller than 20
Because 20 is smaller than 50
Because it is pointing to the left
Because it is blue
I rode my bicycle to grandmother's house at 6 km/h in a flat road for 5 min before reach a hill. I went at 2 km/h up the hill for 3minutes. I met a friend and stopped to talk for 5 minutes. I went on at 2 km/h to my grandmother's house. Draw (plot) the v against t graph for this motion.
The graph can be plotted based on the given information which are given
in pairs (velocity and time), and which the coordinate pairs are formed.
Please find attached the required v against t graph created with MS ExcelReasons:
The given data are presented in a tabular form as follows;
[tex]\begin{tabular}{|c|c|c}\underline{Duration (Minutes)} & \underline{Speed (km/h)}\\0 - 5 &6 \\5 - 8&2\\8 -13&0&\\13- &2&\end{array}[/tex]
The velocity time graph can be plotted using the above table values on
MS Excel using the above table elaborated as follows;
[tex]\begin{tabular}{|c|c|c}\underline{Duration (Minutes)} & \underline{Speed (km/h)}\\0 &6 \\5&6\\5 &2\\8&2\\8&0\\13&0&\\13 &2&\end{array}[/tex]
The attached graph can then be created using the Insert → Chart menu
after selecting the data above inputted in the spreadsheet button on MS
Excel.
Learn more about velocity time graph here:
https://brainly.com/question/24874645
https://brainly.com/question/13522898
write two example in which chemical energy is converted into heat energy
Answer:
batteries in an electric heater, a nuclear power plant
Explanation:
sorry if it wrong g
The right to gather to advance some political or social cause is known as
Answer:
the first amendment
Explanation:
the first amendment to the United States constitution allows the freedoms concerning religion, expression, assembly, and the right to gather and petition.
What is the kinetic energy of a 2,000-kg boat moving at 5.0 m/s?
Answer:
25kJ
Explanation:
K = 1/2 mv^2 = 1/2 x 2000kg x (5.0m/s)^2
= 25 x 10^3 J = 25kJ
Part 1: A flower has 26 chromosomes. To create a new flower, how many chromosomes would a sperm cell have? What is this process called? Part 2: Within a flower cell that has 26 chromosomes, how many chromosomes would a cell that is created within the stem of a flower as it grows, have? What is this process called?
Answer/Explanation:
Part 1: 13 chromosomes.
Reproductive cell, male or female, whose nucleus contains only one chromosome of each pair (they are said to be haploid n = 13) and which unites with the gamete of the opposite sex (fertilization) to give birth to an egg (zygote 2n = 26 ) diploid resulting from the association of the two gametes with each his half of the genetic capital.
2. The process of creating a new flower is called reproduction.
Human reproduction is the process by which a man and a woman engender a new individual. It is a method of sexual reproduction.
Sexual reproduction requires:
Cells carrying parental genes, gametes: eggs and spermatozoa generated by meiosis.The encounter between male and female gametes: fertilization.What is carbon dating?
Answer:
Im pretty sure its number 2
Explanation:
The first one a scientific way of finding the age of something that is very old (such as a dinosaur bone) by measuring the amount of certain forms of carbon in it
Name two processes that release nuclear energy?
Answer: Nuclear energy is released from an atom through one of two processes: nuclear fusion or nuclear fission. In nuclear fusion, energy is released when the nuclei of atoms are combined or fused together. This is how the sun produces energy. In nuclear fission, energy is released when the nuclei of atoms are split apart.
Let me know if it helps!
Two forces are applied to a 50-kg box. One is 60.0
N to the south and the other is 80.0 N to the east.
These are the only forces acting on the box. The
magnitude of the acceleration of the box is:
1. 20m/s^2
2. 1.5 m/s^2
3. 5.2 m/s^2
4. 0.50m/s^2
5. 10m/s^2
The magnitude of the acceleration of the box is 2 m/s².
The given parameters;
mass of the box, m = 50 kgfirst force, F₁ = 60 N southsecond force, F₂ = 80 eastThe resultant of the two given forces is calculated as follows;
[tex]F= \sqrt{F_1 ^2 + F_2 ^2} \\\\F = \sqrt{60^2 + 80^2} \\\\F = 100 \ N[/tex]
The magnitude of the acceleration of the box is calculated as follows;
[tex]F = ma\\\\a = \frac{F}{m} \\\\a = \frac{100}{50} \\\\a = 2 \ m/s^2[/tex]
Thus, the magnitude of the acceleration of the box is 2 m/s².
Learn more about acceleration here:
https://brainly.com/question/17067013
explain the production of current with the help of a magnet and describe which device works on this phenomena
Answer:
Explanation:
The properties of magnets are used to make electricity. Moving magnetic fields pull and push electrons. ... Moving a magnet around a coil of wire, or moving a coil of wire around a magnet, pushes the electrons in the wire and creates an electrical current.
A marble is launched at by dropping it through a marble launcher. The marble took 0.22s to land 0.31m from
where it was launched. Find the horizontal velocity of the marble as it rolls off the table.
A. 1.4m/s
B. 0.53m/s
C. 0.71 m/s
D. 0.07m/s
Hi there!
For projectile motion, the horizontal and vertical components are SEPARATE.
We can use the kinematic equation to solve:
dₓ = vₓt
We can rearrange to solve for vₓ:
dₓ/t = vₓ
0.31/0.22 = vₓ
vₓ = 1.4 m/s ⇒ A
A 0.5 kg cheeseburger is lobbed at a particularly unhappy customer with a force of 10 N.
While it is being thrown, what is the acceleration experienced by the cheeseburger?
Answer in units of m/s2
Which type of forces creates contact between surfaces?
Answer:
Frictional Force: Frictional force is the force caused by the relative motion of two surfaces that come into contact with each other.
Heat rising in a hot-air balloon is an example of __________.
1. Look at this data table
What data seems to be inconsistent with the rest? What are 2 different explanations for this data?
Using visual inspection and knowledge of linear regression , the inconsistent input is the last data point (30, 12.0).
Looking at the data, there is a negative relationship between the depth of water sample and the amount of dissolved oxygen. As the depth increases, the amount of dissolved oxygen decreases. However, the last data point does not concur with this trend. This might have been caused by imputation error or error in the measuring device used.Therefore, the inconsistent data point is (30, 12.0)
Learn more : https://brainly.com/question/25651592
can someone sent some gravity questions
Answer:
can gravity from waves
Explanation:
yes gravity can froms way
A container on the highway with a round hemispherical end is considered a(n) _________ pressure container.
Answer:
high pressure container
A container on the highway with a round hemispherical end is considered a(n) High-pressure container.
What is pressure ?Pressure (symbol: p or P) stands the force involved perpendicular to the surface of an object per unit area over which that force exists distributed. 445 Gauge pressure (even spelled Gage pressure) exists the pressure comparable to the ambient pressure.
Various units exist utilized to represent pressure. Some of these derive from a unit of force separated by a unit of area; the SI unit of pressure, the pascal (Pa), Pressure may also be represented in terms of standard atmospheric pressure; the atmosphere (atm) stands equivalent to this pressure, and the tore exists described as 1⁄760 of this.
Hence, A container on the highway with a round hemispherical end is considered a(n) High-pressure container.
Learn more about High-pressure container refer to;
https://brainly.com/question/9451586
#SPJ2
Propose a hypothesis for how the position of the ball will affect the amount of its gravitational pull energy
throwing a ball up initially has a lot of kinetic energy because it is moving upwards ( kinetic energy is energy which a body possesses by virtue of being in motion.) this all then get converted to gravitational potential energy, and for a moment it is stationary before it begins to fall again. by the time it has returned again, all the gravitational potential energy has turned back into kinetic.
Is mixing mixing sugar and cinnamon a chemical or physical change?
Answer:
It is a physical
Explanation:
What is the mass (in kg) of an object which accelerates at 3 m/s^2 when acted upon by a 15 N force?
[tex]\purple{\longrightarrow \sf Force = Mass \times Acceleration}[/tex]
[tex] \longrightarrow \sf Mass = \dfrac{Force}{Acceleration }[/tex]
[tex]\longrightarrow \sf Mass = \dfrac{15}{3}[/tex]
[tex]\longrightarrow \sf Mass = \cancel{\dfrac{15}{3}} [/tex]
[tex]\longrightarrow {\pink{\underline{\underline{\sf{ Mass = 5 \: Kg }}}}}[/tex]
Henceforth :-
The mass of the object is 5 kg.▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
What is benford's law.
Answer:
Known variously as the Newcomb–Benford law, the law of anomalous numbers, or the first-digit law, Benford's Law is the observation that the first digit in many real-world collections of numerical data will be tiny, as shown by the example of the first-digit law.
Explanation:
Hope it helps:)
Best definition of an electromagnetic wave?
A) an electromagnetic wave is a longitudinal wave with electricity
B) an electromagnetic wave is a mechanical wave
C) an electromagnetic wave is a transversal wave that has electrical and magnetic properties
Answer:
Longitudinal and mechanical waves require a medium to support their transmission:
C) is the correct answer
A 1,500 kg car’s speed changes from 30 m/s to 15 m/s after the brakes are applied. Calculate the work done onto the car from the brakes.
The work done onto the car is 506,250 J
The work done on a system implies an increase in the internal energy of the system as a result of some forces acting on the system from the outside.
From the parameters given:
The mass of the car = 1500 kgThe initial speed = 30 m/sThe final speed = 15 m/sThe work done onto the car refers to the change in the kinetic energy (i.e. ΔK.E)
[tex]\mathbf{=\dfrac{1}{2} mv_1^2 -\dfrac{1}{2} mv_2^2}[/tex]
[tex]\mathbf{=\dfrac{1}{2} m(v_1^2 - v_2^2)}[/tex]
[tex]\mathbf{=\dfrac{1}{2} \times 1500 \times (30^2 - 15^2)}[/tex]
= 506,250 J
Therefore, we can conclude that the work done on the car is 506,250 J
Learn more about work done here:
https://brainly.com/question/18762601
PLEASE ANSWER NEED HELP!!!!!!!! PLEASE THE CORRECT ANSWER!!!!!!
Why are those with low cardiovascular fitness more prone to heart disease than those whose cardiovascular fitness is high?
A.
Exercise decreases the size of arteries, causing heart disease.
B.
Those with lower cardiovascular fitness will have weaker heart muscles.
C.
High cardiovascular fitness means that the heart rate is rarely elevated.
D.
Cardiovascular fitness is the only factor that determines the strength of the heart.
PLEASE NO LINKS OR I WILL REPORT YOU
People with low cardiovascular fitness are more prone to heart disease than those whose cardiovascular fitness is high because those with lower cardiovascular fitness will have weaker heart muscles. Thus, the correct option is B.
What is Cardiovascular fitness?Cardiovascular fitness may be defined as the accommodation of the cardiovascular system to furnish oxygenated blood to functioning muscles. It includes the muscles of the heart, lungs, blood vessels, etc.
People with low cardiovascular fitness have lower furnishing of oxygenated blood to various organs like the heart, lungs, etc. Due to this, the muscles of specific body parts or organs may undergo a state of inactivity suddenly for a fraction of seconds.
This activity constantly leads to various heart-related diseases directly or indirectly in the life of an individual.
Therefore, the correct option for this question is B.
To learn more about Cardiovascular fitness, refer to the link:
https://brainly.com/question/11176067
#SPJ1
What is Kepler’s first law?
Answer:
Kepler's First Law: each planet's orbit about the Sun is an ellipse. The Sun's center is always located at one focus of the orbital ellipse. The Sun is at one focus. The planet follows the ellipse in its orbit, meaning that the planet to Sun distance is constantly changing as the planet goes around its orbit.
Answer:
Explanation:
Kepler 's first law - sometimes referred to as the law of ellipses - explains that planets are orbiting the sun in a path described as an ellipse. An ellipse can easily be constructed using a pencil, two tacks, a string, a sheet of paper and a piece of cardboard. Tack the sheet of paper to the cardboard using the two tacks.
Saima travels 2.5 km in 21.2 seconds. What as Saima's initial speed if her final velocity is 10.7 m/s?
Answer:
d/t = (230 km)/(3.25 h) = 70.8 km/h.
Explanation:
what is the direction of the rotational velocity vector of the jar lid when you open a jar of pickles?
Answer:
Explanation:
The rotational velocity vector is directed away from the jar
an astronomer looking out into space will observe that
Answer:
The farther out a galaxy is from Earth, the faster it is moving away.
Explanation:
gold is a metal angu
Answer:
God is a metal- gold is a transition metal and a group 11 element. It is one of the least reactive chemical elements and is solid under standard condition.
•Gold is the chemical element with 79 protons in each atomic nucleus. Every atom containing 79 protons is a gold atom.
