In a series connection with identical loads, the voltage would be the same throughout each demand.
When all of the loads are linked in a row, the circuit is said to be in series. One route alone can carry electricity. The left lights in this circuit would be out if one of the flashbulbs were missing. The voltage across the circuit in a series connection is the sum of the individual voltage drops across each component, while the current flows at a constant rate. A series circuit has a voltage equal to the sum of all individual voltage drops. In a series circuit, the voltage across the circuit and the current flowing through each component are both the same.
Learn more about voltage here-
https://brainly.com/question/29342143
#SPJ4
If a microhydro dam generates 1 mw of power, how much energy will it produce annually?.
8.76 MUs of energy will be produced yearly by the micro-hydro dam.
What is a dam?A dam is a physical obstruction that slows or restricts the flow of subsurface or seawater. Dam-created reservoirs offer freshwater for uses.
Taking into account that the micro-hydro dam produces 1 MW of power
To estimate how much energy this will yearly generate.
There is one unit of electricity per kwh ( kW hours)
A 1000 KW plant becomes a 1 MW plant.
The quantity of toward the in a day when a plant runs continuously at maximum capacity is:
24000 Kwh, approximately 24000 units, is equal to 1000 KW multiplied by 24 hours. Units made during a specific year.
When 1000 KW is multiplied by 24 hours and 365 days, the result is 8,760,000 Kwh, or 8.76 Million Units (MUs).
The micro-hydro dam will generate 8.76 MUs of energy every year.
Learn more about dam, here:
https://brainly.com/question/29483452
#SPJ1
) for laminar flow in a round 10-cm-diameter pipe, at what distance from the centerline (in cm) is the actual velocity equal to the average velocity?
When the acceleration is zero or the speed is constant, instantaneous and average velocities can both be equal. This is because all instantaneous velocities will be equal in this situation.
Explain about the Actual velocity?After the control filter and display filter have been applied, the filtered value that remains is known as the Actual Velocity. The Actual Velocity (Unfiltered) status register provides the unfiltered value, and the Actual Velocity (Control) value provides the first filtered value.
To calculate the velocity, multiply the distance travelled by the time needed to traverse that distance, then add direction. If one's position doesn't change, their velocity is zero.
Velocity is essentially a vector quantity. It is the rate of change in distance. The displacement change rate is the issue. A moving object can never move more slowly than it is moving. An object in motion can move at zero velocity.
To learn more about Actual velocity refer to:
https://brainly.com/question/24445340
#SPJ4
what would be the minimum resist thickness to ensure that the top surface of the polysilicon is not damaged?
Answer:
Deflection of a beam depends on the following parameters:
1.Modulus of Elasticity of steel 200kN/sq. m
2. Moment of Inertia of the beam section
3. Effective Span of the beam
4. Applied load
Minimum thickness recommended is 6mm, from consideration of corrosion etc. however, minimum Structural steel section of thickness may be used provided they satisfy strength and durability requirements.
raising (increasing the elevation of) the outer edge of a road with respect to inner edge is known as
Superelevation is a type of infrastructure building utilized in roadway curves where the outer edge of the pavement is raised above the inner margin.
What do you mean by superelevation?Superelevation is the banking of a road along a horizontal curve to allow vehicles to pass through the curve safely, pleasantly, and at a respectable pace. Speeds rise and tighter horizontal curves necessitate a steeper superelevation rate.The pavement rotating as it approaches and passes through a horizontal curve is known as superelevation. The purpose of superelevation is to help the driver by reducing the lateral acceleration brought on by following the curve.Superelevation is a type of infrastructure building utilized in roadway curves where the outer edge of the pavement is raised above the inner margin. It's a crucial safety component in the design requirements of any road with curves and refers to a feature of the vertical alignment or "profile" of a road when examined in cross-section.To learn more about Superelevation refer to:
https://brainly.com/question/15184829
#SPJ4
wt steel shape is produced by cutting a wide flange beam lengthwise in half. group of answer choices true false
It is true that wt steel shape is produced by cutting a wide flange beam lengthwise in half.
A beam is a structural component that resists loads mostly applied laterally to its axis (an element designed to carry primarily axial load would be a strut or column). Its primary method of deflection is bending. Reaction forces are produced at the beam's support points as a result of the loads placed on it.
As a result of all the forces operating on the beam, internal stresses, strains, and deflections of the beam are caused by shear forces and bending moments within the beams. Beams differ from one another in terms of how they are supported, their profile (the form of their cross-section), equilibrium circumstances, length, and material.
Beams are typically used to describe structural elements in buildings or civil engineering when the beams are horizontal and support vertical loads.
To know more about beam click here:
https://brainly.com/question/23818966
#SPJ4
technician a says that in the event of a total failure of the primary circuit in an fmvss-121 compliant tractor-trailer combination, the rig is designed to be brought safely to a complete stop. technician b says that in the event of a total failure of the primary circuit the relay section of the treadle valve will be actuated mechanically. who is correct?
A technician is a worker in the technology industry who possesses the necessary knowledge, abilities, and skills as well as a practical comprehension of the theoretical underpinnings.
Who is technician?Expert technicians in a certain tool domain often have expert competency in technique and a moderate comprehension of theory.
As a result, technicians in that sector of technology are typically significantly more knowledgeable about technique than the average layperson and even general professionals.
For instance, although not as knowledgeable in acoustics as acoustical engineers, audio technicians are more adept at using sound equipment and are likely to know more about acoustics than other studio staff members, such as performers.
Therefore, A technician is a worker in the technology industry who possesses the necessary knowledge, abilities, and skills as well as a practical comprehension of the theoretical underpinnings.
To learn more about technician, refer to the link:
https://brainly.com/question/14290207
#SPJ1
Which of the following methods is used to notify a provider of the denial of a claim by an insurance carrier?
A. Remittance advice
B. Coordination of benefits
C. Eligibility for insurance
D. CMS-1500 claim form
Answer:
A:Remittance advice
Explanation:
a(n) ? is any transformer in which the primary and secondary circuits have a portion of their two windings in common.
A auto transformer is any transformer in which the primary and secondary circuits have a portion of their two windings in common.
What is transformer?
A transformer is a passive part that moves electrical energy between circuits, whether they be single circuits or multiple circuits. The electromotive force (EMF) across any coils wound around the same core changes in response to changes in the current flowing through any one of the transformer's coils, which causes changes in the magnetic flux in the transformer's core. Without a metallic (conductive) connection between this same two circuits, electrical energy can be transferred between different coils. The 1831 discovery of Faraday's law of induction defines the induced voltage effect in any coil as the result of a fluctuating magnetic flux surrounding the coil.
To learn more about transformer
https://brainly.com/question/26787198
#SPJ1
A small single-cylinder, two-stroke cycle SI engine operates at 4000 rpm with a
compression ratio of 9. At this speed, the engine produces 5 kW of brake power. If
the engine is square with a total displacement volume of 150 cm3
, calculate:
1- Cylinder bore and piston stroke (mm).
2- Crank offset (mm).
3- Average piston speed (m/s).
4- Clearance volume (cm3
).
5- Brake output per total displacement (kW/liter).
6- Number of cycles performed in one second
7- Speed of rotation of the camshaft (rpm)
a 3105 aluminum plate previously cold worked 23% is 2-in thick. it is then cold worked further to 1.4 in. calculate the final elongation.
Answer:
Explanation:
x
during this period, which value best approximates the average value of the san lorenzo river's discharge in cubic feet per second (cfs)?
The total annual discharge of the San Lorenzo River, as recorded at the stream gage near Felton, was almost 400 cubic feet per second (cfs).
ExplanationJust before the Boardwalk, the San Lorenzo River flows through the center of Santa Cruz to the Monterey Bay. Along the river in the Boardwalk and downtown regions is the San Lorenzo Riverway Trail. San Lorenzo Park is located on the northern edge of city, close to the river. In the past, logs from the Santa Cruz Mountains were transported by the river. (To the headwaters of the San Lorenzo River from Felton through a flume.) Over time, the river has receded due to increased water demand. The water moves at a rate of roughly 10 cubic feet per second in the summer. On December 23, 1955, a maximum discharge of 30,400 cubic feet per second was recorded. The Army Corps of Engineers built the current levees by 1959. They
To learn more about lorenzo river's refer to
https://brainly.com/question/25060766
#SPJ4
what material property would still cause strain in a strain gauge that is positioned perpendiclator to the direction of force if it were fully bonded in a high strain region of the sepcimen if this occurs then the set up must be calculated as a two active gauge set up will this set up continue to compensate for the environemental factor
Ductility is the material property would still cause strain in a strain gauge that is positioned. Understanding how an object responds to different forces is necessary for mechanical testing and measurement.
A material's ductility refers to its capacity to withstand plastic deformation or drawing without breaking. As a result, it provides information on how "soft" or pliable the material is. The types and concentrations of alloying elements present affect the ductility of steels in different ways. A material is said to be malleable if it is easy to hammer out a thin sheet of the material. The most malleable metal is gold. The ability of a solid material to deform when subjected to tensile stress is known as ductility.
Learn more about mechanical here-
https://brainly.com/question/20434227
#SPJ4
a homeowner in raleigh, north carolina, wants to install a wind turbine in his backyard to augment electrical power from the grid. a local supplier states that the combined efficiency of their turbines is approximately 0.28. how much electrical power can this turbine generate for a wind speed of 18 m/s if the turbine blade diameter is 6 m?
Answer:
5.68ugs
Explanation:
List 5 cutting actions of sawing machines
pls help
Thin metal blades or flexible bands with teeth on one edge, thin grinding wheels, or thin metal disks with teeth on their edges can all be used as sawing machine cutting tools.
What is sawing machine?Sawing machine is defined as a device for cutting forms out of raw material plates or cutting apart bars of material. It is used to sever material, usually wood, but occasionally metal or stone. The material is cut by pressing the toothed edge against it and pushing it swiftly forward, slowly backward, or continually forward.
Rotating blades, reciprocating blades, and circulating blades are the three basic types of power sawing machines.
Thus, thin metal blades or flexible bands with teeth on one edge, thin grinding wheels, or thin metal disks with teeth on their edges can all be used as sawing machine cutting tools.
To learn more about sawing machine, refer to the link below:
https://brainly.com/question/366955
#SPJ1
when conduit is not used in new residential low-voltage construction, cables can be pulled through the finished wall by the use of a . select one: a. mud ring b. closed box c. sleeve d. ceramic tube
the correct answer is option (d) ceramic tube.
A ceramic tube is most commonly used in industrial high temperature applications, and electrical and thermal insulations. Our high temperature ceramic tubes include alumina, silicon carbide, and quartz choices that have excellent thermal, anti-shock, anticorrosion, and extreme high temperature resistance properties. The uniform dimensional stability of ceramic tubing offers optimal insulation while providing reliable protection.
To learn more about ceramic tube click on link given below:
brainly.com/question/20466176
the hydraulic gradient is: group of answer choices the permeability of the rock. the slope of the water table. the increase in temperature with depth. the rate of flow of groundwater.
Groundwater moves in the direction of maximum decreasing total head under the influence of the hydraulic gradient.
Explain about the hydraulic gradient?The change in water level per unit of distance along the direction of highest head drop is known as the hydraulic gradient (1), which is the slope of the water table or potentiometric surface.
If the gradient is negative, which means the hydraulic head is lower at depth, there is an indication of a downward flow component. The hydraulic head is higher at depth if the gradient is positive, on the other hand, which denotes an upward flow component. The gradient's size tells us a lot about its importance.
This vector depicts the flow direction of groundwater, with zero denoting "no flow" and negative values denoting flow along a dimension.
To learn more about hydraulic gradient refer to:
https://brainly.com/question/15872139
#SPJ4
technician a says that a vehicle with a modified suspension may need an aftermarket kit installed to achieve the specified alignment settings. technician b says that the radar cruise control may have to be recalibrated if aligning a vehicle equipped with an electronic suspension. which technician is correct?
Both technician A and technician B are correct.
Some vehicles may require the installation of aftermarket kit alignments when the suspension is modified. This helps to properly adjust the alignment settings. Therefore, technician A is correct who states that in order to achieve the specified alignment settings, a vehicle with a modified suspension may need an aftermarket kit installed.
Alignment of vehicles done through an electronic suspension may need that recalibrated radar cruise control. Thus, technician B is also correct who says that in the alignment of a vehicle equipped with an electronic suspension, the radar cruise control may have to be recalibrated.
You can learn more about vehicle alignment at
https://brainly.com/question/16857448
#SPJ4
briefly cite the differences between the recovery and recrystallization processes. explain the differences in grain structure for a metal that has been cold worked and one that has been cold worked and then recrystallized
While primary recrystallization proceeds discontinuously by the formation, recovery describes the gradual re-ordering and destruction of the stored dislocations.
High-angle grain boundaries that sweep the deformation substructure infrequently. After cold plastic deformation and/or during hot working, RECOVERY, RECRYSTALLIZATION, AND GRAIN GROWTH are microstructural changes that take place during annealing. Because they return the microstructural configuration to a lower energy level, these three mechanisms are commonly referred to as restoration processes. Recovery is crucial for removing internal stresses from forged, welded, and manufactured equipment without reducing the strength developed during and after use. The most crucial technique for cleaning nonvolatile organic materials is recrystallization. The process of recrystallization requires dissolving the solute, which needs to be purified, in a suitable hot solvent.
Learn more about stresses here-
https://brainly.com/question/17252580
#SPJ4
concrete must be compacted in the forms to eliminate trapped air and to fill completely around the reinforcing steel and into all the corners of the formwork. what tool is used to accomplish this?
A vibrat0r is a tool used to accomplish this.
A vibrat0r is a concrete tool that generates stronger concrete by strenuously shaking the concrete right after it is poured to eliminate the air pockets or air bubbles. The vibrat0r forces the trapped air out of the mixture making the final product a level slab and more compact.
According to the given context where concrete is compacted in the form in order to eliminate trapped air and fill around the reinforcing steel and into all of the corners of the framework. The tool named vibrat0r can be used to serve the purpose.
You can leran more about concrete at
https://brainly.com/question/25500184
#SPJ4
the model that resembles a systems approach with inputs at the base, processes in the center, and outputs at the top is known as the:
The model that resembles a systems approach with inputs at the base, processes in the center, and outputs at the top is known as the team Leadership Model.
What Is a Leadership Model?A leadership model is a conceptual framework for the most effective personnel management.It often offers a commensurate, effective way of responding to organizational and employee demands. Interviews, discussion, openness to viewpoints from the public and private sectors, and individuals from all levels of an institution's structure are all components of a systems approach. A leader's method for giving instructions, carrying out strategies, and inspiring people is referred to as their leadership style.There are three primary leadership styles, according to study conducted in 1939 by psychologist Kurt Lewin and his team: authoritarian (autocratic), participative (democratic), and delegative (Laissez-Faire).To learn more about systems approach refer
https://brainly.com/question/13149592
#SPJ4
The voltage difference in a graphing calculator is 6V and the resistance is 1200 what is the current through the batteries of the graphing calculator?
The current through the batteries of the graphing calculator is 0.005 A
How to calculate current through the batteries of the graphing calculator?The potential difference in charge between two sites in an electrical field is quantified as voltage, also known as electromotive force.
When charged electrons (current) are forced through a conducting loop by the pressure of an electrical circuit's power source, they can perform tasks like lighting a lamp. In a nutshell, voltage is measured in volts and equals pressure.
The derived unit for electric potential, voltage, and electromotive force is the volt (symbol: V). The Italian physicist Alessandro Volta (1745–1827), who created the voltaic pile, conceivably the first chemical battery, is honored by having his name attached to the volt.
Given ,
I = ?
V = 6V
R = 1,200 Ω
I = 6V / 1,200 Ω
I = 0.005 A
To learn more about voltage refer to:
https://brainly.com/question/1176850
#SPJ1
assume the skin friction drag on the airfoil is essentially that for a flat plate with the boundary layer being laminar and incompressible. what percentage of the total drag is due to skin friction?
Preliminary studies found that skin friction drag accounts for between 20 to 40% of overall drag.
Explain about the skin friction?Aerodynamic drag, which is a resistive force applied to an object moving in a fluid, includes skin friction drag.
The viscosity of a fluid as it passes across a surface is what creates skin friction. Its size is determined by the fluid's viscosity, the amount of wetted (or total) surface area in contact with it, and the degree of roughness of the surface.
Skin friction is important because it plays a role in the erosion of sediment particles from the water-bed boundary condition. Regarding the vertical mixing of the sediment over the water depth, form drag-related turbulence (separation-induced eddies, etc.) is significant.
To learn more about skin friction refer to:
https://brainly.com/question/14174373
#SPJ4
technician a says that cylinder components are the most highly stressed parts of the diesel engine. technician b says cylinder pressures can now exceed 3000 pounds per square inch (psi) (20,684 kilopascals [kpa]) of force. who is correct?
Only technician A is correct because cylinder components are the most highly stressed parts of the diesel engine but cylinder pressures can NOT exceed 3000 pounds per square inch (psi) at this time.
What are the facts that prove the above?The findings of the nonlinear static analysis revealed that the high-stress area was situated in the crack start zone while the engine was operating at maximum power.
Peak cylinder pressures near TDC (where spark occurs) will be in the 300 psi range for light load engines, 1000 psi for full-power production engines, and 1500 psi or higher for race engines.
Learn more about Diesel Engines:
https://brainly.com/question/8829745
#SPJ1
which type of drawing commonly describes hydraulic and pneumatic circuits electrical power and fluid flow
The type of drawing commonly describes hydraulic and pneumatic circuits electrical power and fluid flow is fluid power.
The technologies of hydraulics and pneumatics are referred to as fluid power. Both systems transfer electricity from one place to another using a fluid (liquid or gas). In pneumatics, the fluid is a gas, whereas in hydraulics, the fluid power is typically a liquid (oil) (usually compressed air).
Both are methods of power transmission, which is the science of transforming energy into a form that is more usable and transferring it to the locations where it is required. Electrical, mechanical, and hydraulic power are the three most popular ways to transmit power.
Although they are occasionally seen as rival technologies, there is no one type of power transmission that is ideal for all uses. In actuality, a variety of technologies are used to suit the majority of applications. However, compared to other methods, fluid power has several significant advantages.
To know more about fluid power click here:
https://brainly.com/question/12947998
#SPJ4
in the moren corporation (a) case, we learned what important lesson when selecting professional engineering services?
Moren has experience with two of the three engineering companies: Travers & Bolton (T&B) and Crown Engineering (CE). Both have contributed significantly and satisfactorily.
The conversion of the 120 kV to 230 was already assigned to T&B, and it was suggested that a reliable engineering firm be hired to handle the conversion.Group of potential solutions It is the responsibility of procurement to ensure that the technical proficiency of those delivering engineering services satisfies the demands of their internal client. On occasion, procurement must defy internal client preferences when choosing the engineering services provider for a significant, multimillion-dollar building project.
Learn more about engineering services here:
https://brainly.com/question/18063021
#SPJ4
which of the following is not a performance technique developed by stanislavski? multiple choice through line biomechanics concentration and observation magic if
Through line biomechanics concentration and observation magic if International Society of Biomechanics in sports.
What is "International Society of Biomechanics in sports"?The recently developed professional association in biomechanics is the "International Society of Biomechanics in sports".It is the professional association in bio-mechanics.
It is an international society which is dedicated to bio-mechanics to sports. The main purpose of the society is to understand and study the human movement and its relation to sport bio-mechanics. They provide information regarding bio-mechanics in sports.
Therefore, Through line biomechanics concentration and observation magic if International Society of Biomechanics in sports.
Learn more about biomechanics on:
https://brainly.com/question/13898117
#SPJ1
A vehicle can hydroplane in speeds as low as __ mph.
Answer:35
Explanation:
a plan or series of plans showing the placement of each lighting instrument and its type, wattage, size, wiring, and color is called
a plan or series of plans showing the placement of each lighting instrument and its type, wattage, size, wiring, and color is called light plot.
What is on a light plot?Specifically for theatrical lighting designers, a light plan, lighting plot, or merely plot is a document similar to an architectural blueprint used to depict and communicate the lighting design to the director, other designers, and finally the Master Electrician and electrics team.Each fixture in the Instrument Schedule typically includes a single line of text.Other than what can be inferred from the hanging position name and fixture's sequence number, it lacks the particular fixture location information that the Light Plot has.To learn more about Light Plot refer,
https://brainly.com/question/28245288
#SPJ4
derive the characteristic state equations for the following components: a. a) sr latch b. b) gated d latch c. c) jk flip-flop d. d) t flip-flop
The state equations for sr latch b are S+R'Q, gated d latch is D, jk flip-flop is JQ' + K'Q and for t flip-flop T'Qn + TQn' .
What is Flip flop ?One of a flip-flop's two states corresponds to a "one," and the other state corresponds to a "zero," and it is a device that stores a single bit of data.
Signals applied to one or more control inputs and one or two outputs allow the circuit to alter state. It is the fundamental component of storage in sequential logic.
Fundamental components of digital electronics systems used in computers, communications, and many other sorts of systems include flip-flops and latches.
Common types of flip-flops are the SR (set-reset), D (data or delay), T (toggle), and JK. The so-called characteristic equation can be used to explain a type's behaviour.
t flip-flop Qn+1 = T'Qn + TQn'SR flip flop Qn+1=S+R'QJ-k flip flop Qn+ 1 = JQ' + K'QD flip flop Qn+ 1 = DTo learn more about flip flop refer :
https://brainly.com/question/13981199
#SPJ4
The tactile system is the sensory system that refers to the sense of touch. Please select the best answer from the choices provided t f.
True is the correct response. The task of processing touch data from the body falls on the tactile system.
Through neurological connections to the spinal cord, brain stem, and thalamus, the body transmits tactile data to the somatosensory cortex.
The trigeminal system, which causes somatosensory feelings, and the primary olfactory system, which produces scent sensations, make up the olfactory system at the anatomical level (tactile, thermal, pain, humidity). The third component, referred to as the "vomeronasal organ," is positioned behind the nostril opening. Because the afferent nerve of the vomeronasal organ in humans stops functioning by the 18th week of fetal development, the organ stays in a primitive state.
Learn more about system here-
https://brainly.com/question/27162243
#SPJ4
