The time constant of the circuit is 2.10 s.
How do you find time constant in a circuit?The product of the circuit resistance (in ohms) and the circuit capacitance yields the RC time constant, often known as tau, the time constant (in seconds) of an RC circuit (in farads)The equation T = R*C in seconds is used to get the time constant,.An RLC circuit's transient response and time constant can be extracted from simulations in one of two ways: Simply fit the circuit's time-domain response (natural log scale) using a transient simulation, as was mentioned before, and determine the transfer function from the slope.The formula for an RL circuit's time constant is =L/R.The time constant specifies the amount of time it takes for a signal to be reduced to 1/e, or roughly 37%, of the output signal.Given data :
product of the circuit resistance = 2.81 msms
circuit capacitance = 0.75
By applying the equation T = R*C in seconds is used to get the time constant.
T = R x C =
= 2.81 x 0.75 = 2.10 s
Learn more about time constant in a circuit refer to :
https://brainly.com/question/28045311
#SPJ4
A golfer is teeing off a 160.0 m long par-3 hole. the ball leaves with a velocity of 40.0 m/s at 50.0° to the horizontal. assuming that she hits the ball on a direct path to the hole, how far from the hole will the ball land (no bounces or rolls)?
The distance the land near hole is -0.6
As we know that the golfer hits the ball with a speed of 40 m/s at an angle of 50 degrees
so here we will have the range of the ball on the ground given as
R = v² sin2∅/g
so we will have
[tex]R =\frac{40^{2}sin(2*50) }{9.81}[/tex]
R = 160.6
So it will land at a distance of 160.6 m
so the distance from the hole is given as:
d = 160 -160.6
d = -0.6
To calculate the horizontal distance as the projectile travels Multiply the vertical height h by 2 and divide by the acceleration due to gravity g. Take the square root of the result from step 1 and multiply it by the initial projection velocity u to get the horizontal distance.
The maximum horizontal distance a baseball travels is the horizontal distance a baseball travels when returning to its initial height. An example of horizontal distance is the distance from an observer to a building, and an example of vertical distance is the height of a building. Players are given a reasonable amount of time to reach the hole and must wait an additional 10 seconds for the ball to fall into the hole. If the ball falls into the hole during this waiting time.
Learn more about A velocity here:-https://brainly.com/question/24681896
#SPJ9
a gas does 189 j of work while expanding, and at the same time it absorbs 154 j of heat. what is the change in internal energy?
35 joule is the change in internal energy when a gas does 189 j of work while expanding, and at the same time it absorbs 154 j of heat.
w= -189
q=154
E=w+q
E= -189+154
E=-35 joule
Internal energy is a property or state function in thermodynamics that describes a substance's energy when capillary effects and the effects of external magnetic, electric, and other fields are not present. As with any other state function, the energy's value depends on the substance's state rather than the kind of methods employed to get there. The first law of thermodynamics states that when a system changes state as a result of a process in which only work is involved, the work is equal to the change in internal energy.
To know more about internal energy visit : https://brainly.com/question/11278589
#SPJ4
which of the following quantities are units of impulse? (there could be more than one correct choice.)A) N ∙ m
B) kg ∙ s/m
C) kg ∙ m/s
D) N ∙ s
E) kg ∙ m2/s2
The units of impulse are C) kg . m/s and D) N .s. Hence, option C) and D) both are correct.
What is impulse?Impulse determines velocity of an object after a force acts on it and this can be seen as a consequence of impulse being a change in momentum. SI unit of impulse is Newton-seconds and dimensionally equivalent unit of momentum is kilogram meter per second (kg⋅ m/s).
In classical mechanics, impulse is the integral of force over the time interval for which it acts. As we know that force is a vector quantity, so is impulse. Impulse applied to an object produces equivalent vector change in its linear momentum and also in the resultant direction.
To know more about impulse, refer
https://brainly.com/question/904448
#SPJ4
The moment of inertia for a point mass m and rotating around a radius of r is what?.
this proves that the moment of inertia of a point mass M rotating around an axis at a distance R is the same as the moment of inertia for a thin ring of mass M and radius R measured around its central axis.
All these are possible because a thin ring can be thought of as a collection of many point masses collectively making that ring.
The moment of inertia for a point mass m and rotating around a radius of r is inertia (I).
The moment of inertia of a point mass is the product of its mass and the square of its distance from the axis of rotation. Let the mass be M and the distance be R. So, the moment of inertia is
I= M[tex]R^{2}[/tex]
Now let's consider a thin ring of mass M and radius R. The ring is made up of infinite numbers of point masses. All these point masses are at an equal distance from the center which is equal to the radius of the ring. Let's divide the ring into N numbers of point masses each having an equal mass. So, the mass of each point mass is
M= M/N
All these point masses are at an equal distance from the center of the ring. And that distance is the radius R. So, the moment of inertia of each point mass is
I’ = m[tex]R^{2}[/tex]
Therefore, the total moment of inertia of the ring is
I = I’ +_ I’ + I’ +........up to N terms
=> I = NI’
=> I=Nm[tex]R^{2}[/tex]
=> I= N (M/N)[tex]R^{2}[/tex]
=> I= M[tex]R^{2}[/tex]
Similar to how mass determines the force needed to achieve the desired acceleration, a rigid body's moment of inertia, also known as its mass moment of inertia, angular mass, second moment of mass, or, more precisely, rotational inertia, is a property that determines the torque needed to achieve a desired angular acceleration about a rotational axis.
Depending on the axis selected and the distribution of the body's mass, a change in the body's rate of rotation will need a greater torque for larger moments.
The moment of inertia for a point mass is just the mass times the square of the distance perpendicular to the axis of rotation. This is an extensive (additive) property.
To learn more about a moment of inertia visit here:
brainly.com/question/21439277
#SPJ4
if a simple pendulum with length 1.50 meters makes one oscillation in 2.446 seconds, what is the acceleration due to gravity at its location?
The acceleration due to gravity at the point is 6.58 m/s
What is gravity?
In mechanics, gravity—also known as gravitation—is the constant force of attraction that pulls all matter together. It has no impact on determining the internal characteristics of common matter because it is by far the weakest known force in nature. In contrast, it governs the structures as well as evolution of stars, galaxies, and the entire cosmos through its extensive and universal action, which affects the trajectories of objects in the solar system and throughout the universe. All objects on Earth have a weight, or a gravitational pull downward, proportional to their mass, which is a result of the mass of the planet. The acceleration that gravity gives to objects falling freely serves as a gauge of its strength. The acceleration of gravity at Earth's surface is approximately 9.8 metres (32 feet) per second per second.
As Given, The length of pendulum is 1.5 m
Time taken for one oscillation is 2.446 s
Formula used to find acceleration due to gravity is g= (2π/T)²L
Now substituting the values,
g= (2×3.14/2.446)²×1
g= 6.58 m/s
From the above observation, the acceleration due to gravity at its location is 6.58 m/s.
To know more about gravity, visit
https://brainly.com/question/557206
#SPJ4
a 1.57-cm panel of a certain material can absorb 85.5% of incoming rays from a radioactive source. how thick of a panel, in cm, of that same material would you need to absorb 99.2% of the rays?
The thickness of the panel should be 1.82 cm.
According to Beer-Lambert law, the absorbance([tex]A[/tex]) of certain incident energy from a medium is given by [tex]A = \epsilon Lc[/tex] where [tex]\epsilon, L\,\text{and}\,c[/tex] denote the molar absorption coefficient, the direct length of the medium and the concentration of the medium.In this situation, since it is the same medium that applies, we can think of the formula in its proportion mode as [tex]A \propto L[/tex].Now we can apply this simplified formula to both situations and find the needed quantity as follows,[tex]\begin{aligned}\\\\\frac{99.2\%}{85.5\%}&=\frac{L}{1.57\,cm}\\\\L&=1.82\,cm\end{aligned}[/tex]
This result is satisfying as more energy can be thought to be lost in the medium during its travel through the medium so the absorbance is higher.To know more about absorbance follow the link below.https://brainly.com/question/29434481
#SPJ4
The electron transport chain consists of a series of _____ that serve as electron carriers.
A group of proteins that act as electron carriers make up the electron transport chain.
How are electrons introduced into the electron transport system?All of the electrons that enter the transport chain come from NADH and FADH2 molecules created during the glycolysis, pyruvate oxidation, and citric acid cycle, which are early phases of cellular respiration.
Electrons are transferred from one molecule to another in the electron transport chain, and the energy released during these electron transfers is utilised to create an electrochemical gradient. The energy held in the gradient is utilized in chemiosmosis to produce ATP.
NAD +start superscript, plus, end superscript (nicotinamide adenine dinucleotide, as illustrated below) and FAD are two forms of electron carriers that are particularly significant in cellular respiration (flavin adenine dinucleotide).
To know more about electron transport visit:
https://brainly.com/question/24372542
#SPJ13
the wavelength of the green light from a traffic signal is centered at 522 nm. what is the frequency in hertz of this radiation? x 1014 hz
The frequency in hertz of this radiation if the wavelength of the green light from a traffic signal is centered at 522 nm is 0.575 * [tex]10^{15}[/tex] m
f = c / λ
f = Frequency
c = Speed of light
λ = Wavelength
c = 3 * [tex]10^{8}[/tex] m / s
λ = 522 nm = 522 * [tex]10^{-9}[/tex] m
f = 3 * [tex]10^{8}[/tex] / 522 * [tex]10^{-9}[/tex]
f = 0.575 * [tex]10^{15}[/tex] m
f = 0.575 Pm
Frequency is the repetition of an event per unit amount of time. The wavelength is the distance between identical points in adjacent cycles of a wave.
Therefore, the frequency in hertz of this radiation is 0.575 Pm
To know more about Frequency
https://brainly.com/question/2140860
#SPJ4
What is the accuracy of the model?.
The ratio of the total number of predictions made to the number of classifications a model correctly predicts is known as model accuracy.
It's one method of evaluating a model's performance, but by no means the only one. Accuracy offers the best insight into how well a model is performing on a particular dataset when taking into account a large number of rich measurements at once rather than any one of them individually.In many cases, a model's accuracy needs to be improved because the first pass at training it was insufficient. This is typical in machine learning; some iteration on your initial models is required because it is nearly impossible to create a model that perfectly fits all the goals you initially set out to achieve on your first try.Demerits of model accuracy :- In addition, accuracy could be increased by switching to a totally different model. Convolutional neural networks are one of the top models for classifying images, for instance, as is now widely acknowledged. One could switch to a completely different model, such as the convolutional neural network, for more accurate readings if one had started out on an image classification problem with a simple logistic regression over pixel values in the image and wasn't getting the hoped for performance.To know more about Convolutional neural networks -
https://brainly.com/question/7774945
#SPJ4
which of the following situations do you think is more risky: one where a car is breaking up to -3 meters per second squared, or one where it is braking up to -8 meters per second squared? why? follow up: can you think of a situation where it can be the opposite?
Braking up to -8 meters per second squared is more risky than the other one.
What is inertia?According to the definition of inertia, matter has the ability to remain at rest or to move uniformly in a single direction unless applied with an external force.
The ability of moving object to remain in moving uniformly in a single direction is called inertia of moving.
In this case, the car moving with certain velocity has inertia of moving. By certain applying brakes of more deceleration is more risky as it works opposite to the inertia of moving. Hence, braking up to -8 meters per second squared is more risky than breaking up to -3 meters per second squared.
As 8 meters per second squared acceleration or deceleration is larger compare to other; there may have no situation where it can be the opposite.
Learn more about inertia here:
https://brainly.com/question/3268780
#SPJ1
During parkour, a person leaps at a wall and performs a flip. What must they do to change directions?.
That person has to exert a significant amount of the force on the wall to make flip happen.
When a person flips, during this process first thing he exerts a significant amount of the force on the wall, so this force will give push in opposite direction according to the third law of Newton's law.
During he applies force, he bents and that's where centripetal force will help to keep his body on the air and meanwhile he is bending more to balance himself when he touches the ground. Balancing of force is the key in this process.
To learn more about the force, visit here
https://brainly.com/question/13191643
#SPJ4
Danica observes a collision between two vehicles. she sees a large truck down the road. it strikes a small car parked at the side of the road. complete the library passage summarizing the collision
a) On colliding, the truck applies a force on the stationary car, and the stationary car applies an equal opposite force on the trunk.
b) The front of the truck is designed to crumple in order to lower the force impact on stationary car accelerate both vehicles passengers - which protects the well-being of the passengers.
Firstly, we see that the collision between truck and car is a head of collision.
We have required to find the force which car apply on truck in opposite direction.
Force is a defined as the product of mass of object by acceleration of an object.
According to Newton's third law of motion, whenever one object applies a force on another object , the second object also applies an equal and opposite on the first one.
This is law tells that every action has equal and opposite reaction.
So, we conclude that if a truck applies a force on a stationary car during collision then stationary car also applies equal magnitude of force on truck but in opposite direction.
Now, a crumble is applied in front of truck before collision to stationary car.
force of impact is defined as the force generated when the objects collide with each other.
when a crumble designed in front of truck , it increase the collision time between truck and stationary car. As the time increase it implies acceleration of truck become smaller.
Mathematically , a = v/t
So, the force on the trunk becomes smaller.
because of Newton's second law of motion,
F = ma
therefore, if accleration is smaller then force applied by trunk is also smaller/ lower.
this results lower the force of impact and it saves the passengers from injury by protecting them from impact.
To learn more about Newton's laws of forces, refer:
https://brainly.com/question/28171613
#SPJ4
#Complete Question
Danica observes a collision between two vehicles. She sees a large truck driving down the road. It strikes a small car parked at the side of the road. Complete the passage summarizing the collision.
On colliding, the truck applies a force on the stationary car, and the stationary car applies - A smaller, A greater, An equal- . and opposite force on the truck. The front of the truck is designed to crumple in order to - Lower the force of impact, Apply maximum force on the stationary car, Accelerate both vehicles passengers - , which protects the well-being of the passengers
Is the amount of energy required to get a spacecraft from the earth to the moon greater than, less than, or equal to the energy required to get the same spacecraft from the moon to the earth?.
The amount of energy required to get a spacecraft from the earth to the moon will be greater than the energy required to get the same spacecraft from the moon to the earth.
The reason for this is firstly it's harder to leave the Earth than the moon. There's six times the gravity and an atmosphere to push through. Even if you're just going into orbit, you need at least a medium-sized rocket.
Moreover, when we launch a rocket from the earth, it has to push all the equipment and fuel needed to get to the Moon and then back. When launching from the moon- at least with the Apollo mission model- you only need enough fuel to get two astronauts and their equipment back into lunar orbit.
Also, because Earth has an atmosphere- this lets you slow down at Earth without using any fuel.
Learn more about the energy required by spacecraft from the earth to the moon here:
https://brainly.com/question/1665464
#SPJ4
If B is added to A, under what condition does the resultant vector have a magnitude equal to A+B.
If B is added to A and the resultant vector have a magnitude equal to A+B if the angle between vector A and b is zero or either magnitude of A or b is zero.
I A I = √ A . A
I B I= √ B . B
I A + B I = √ (A + B ) ( A + B )
I A + B I = √ AA + AB + BA + BB
I A + B I = √ I A I² + I B I² + 2 I A I I B I Cos θ → ( 1 )
Given condition
I A + B I = I A I + I B I
I A + B I² = ( I A I + I B I )²
I A + B I² = I A I² + I B I² + 2 I A I I B I → ( 2 )
Equating ( 1 ) and ( 2 ),
I A I² + I B I² + 2 I A I I B I Cos θ = I A I² + I B I² + 2 I A I I B I
2 I A I I B I Cos θ = 2 I A I I B I
I A I I B I ( cos θ - 1 ) = 0
So either,
I A I = 0
I B I = 0
cos θ - 1 = 0
cos θ = 1
θ = 0°
Therefore, if B is added to A and the resultant vector have a magnitude equal to A+B if the angle between vector A and B is zero or either magnitude of A or B is zero.
To know more about resultant vector
https://brainly.com/question/28188107
#SPJ9
calculate the ratio of the resistance of 15.0 m of aluminum wire 2.2 mm in diameter, to 23.0 m of copper wire 2.0 mm in diameter.
The ratio of the resistance was found to be 0.85013
Define resistance?
Resistance is a measure of the resistance to current flow in an electrical circuit.
The Greek letter omega () represents resistance in ohms. Ohms are named after Georg Simon Ohm (1784-1854), a German scientist who researched the link between voltage, current, and resistance. Ohm's Law is attributed to him.
the formula for calculating the resistance was R= ρ 1/s
ρal=2.65(10)^-8 mΩ
ρcu= 1.68(10)^-8mΩ
l al=15.0 m
l cu= 23.0 m
s= π(d/2)^2
d= diameter
dal=2.2mm=0.0022m
dcu= 2.0mm=0.0020m
for aluminum
Sal= π(0.0022/2)^2
=3.14(0.0022/2)^2
=3.14(0.0011)^2
=3.14(0.00000121)
=0.0000037994
for copper
scu= π(0.0020/2)^2
=3.14(0.000001)
=0.00000314
resistance of aluminum
Ral=2.65(10)^-8mΩ x 15/0.0000037994
=2.65(10)^-8 x 15/3.7994
=0.001046
resistance of copper
Rcu= 1.68(10)^-8mΩ x 23/0.00000314
=1.68(10)^-8x 7.324
=0.0012304
The ratio of the resistance = 0.001046/0.0012304
=0.85013
therefore the final ratio of the wires was = 0.85013
To learn more about resistance follow the given link: https://brainly.com/question/1364361
#SPJ4
what is the average magnitude of the poynting vector 3.50 mi from a radio transmitter broadcasting isotropically (equally in all directions) with an average power of 260 kw?
1.68 is the average magnitude of the poynting vector 3.50 mi from a radio transmitter broadcasting isotropically (equally in all directions) with an average power of 260 kw
Given In questionquestion :
Power of Radio Transmission(P) = 260W
Radius of Transmission Ares(r) = 3.5 metre
Expression of average value of the magnitude of the Poynting vector(S) is ;
S = P/area of radio transmission([tex]4\pi r^{2}[/tex])
S = 260 / [4×[tex]\frac{22}{7}[/tex] ×[tex]3.5^{2}[/tex]]
S = 1.68
So, The of average value of the magnitude of the Poynting vector is 1.68
What is Poynting vector?
In physics, the Poynting vector represents the directional energy flux or power flow of an electromagnetic field. The SI unit of the Poynting vector is the watt per square metre; kg/s³ in base SI units. It is named after its discoverer John Henry Poynting who first derived it in 1884.
To learn more about Poynting Vector visit here ; https://brainly.com/question/28215376?referrer=searchResults
#SPJ4
closing the mouth is of the mandible. opening the mouth is of the mandible. drawing the shoulders anteriorly, or protruding the mandible outward, is of the scapulae or mandible. pulling the shoulders back, as in sticking out your chest, is of the scapulae. making a conical motion with a limb, as in drawing a circle, is called .
Making a conical motion with limb as drawing a circle is called the humerus.
What is humerus?Humerus is the largest bone in the arm and the only bone in the upper arm. Movement of the humerus is essential for all varied activities. Humerus is the only bone in the upper arm. This bone has many uses because it is directly related to the human hand, which plays a very important role for humans.
From the statement above, we get various important information. Mandible is the lower jawbone which is the largest and strongest bone in the facial area. This bone is useful for helping humans in chewing food, speaking, and other activities that require the use of the lower jaw.
Learn more about humerus https://brainly.com/question/7194643
#SPJ4
How do you find kinetic energy with mass and speed in physics?.
The kinetic energy with mass and speed in physics K.E. = 1/2 m v².
If the mass is in kilograms and the velocity is in meters/second, then the kinetic energy is in kilograms - meters squared/second. Kinetic energy is proportional to the square of velocity, so doubling velocity quadruples kinetic energy. The energy transferred is called kinetic energy and depends on the mass and velocity achieved.
Kinetic energy is transferred between bodies and converted into other types of energy. Equations of motion are a set of equations that describe the motion of an object with constant acceleration. Equations of motion require knowledge of derivatives rates of change and integrals.
Learn more about Kinetic energy here:-https://brainly.com/question/25959744
#SPJ4
Salt water is more dense than fresh water. A ship floats in both fresh water and salt water. Compared to the fresh water, the volume of salt water displaced by the ship is.
To create a fluid weight equivalent to the weight of the object, less of a more dense fluid must be moved. The amount of displaced water won't be as great because the salt water is denser.
Freshwater is less dense than saltwater. More dense substance will be located below less dense material. When salt is dissolved in water, as it is in ocean water, the added mass of the dissolved salt increases the density of the water relative to that of the water without salt. Consequently, when the density of the fluid increases, upward Due to the increase in buoyant force, objects will float more easily in salt water. Seawater has a higher density and buoyancy than freshwater. Water that is pure is less dense.
Learn more about density here-
https://brainly.com/question/943734
#SPJ4
which nonmetal forms a gas commonly found in our atmosphere? responses cl uppercase c lowercase l n n i i rn
Acc to the responses given in the query:
Nonmetal forms a gas commonly found in our atmosphere is chlorine (Cl, element 17)
Many of the nonmetals are gases when they are in their elemental state. Example Hydrogen, Flourine, Oxygen, and Nitrogen. (H2, N2, O2, F,and Cl2.)
Describe a non metal.A non-metallic chemical element that may create anions, acid oxides, acids, and stable hydrogen compounds. Examples include boron, carbon, and nitrogen. When compared to metals, nonmetals' electrons exhibit different behaviour. Elements with 4, 5, or 7 electrons in their outermost shell are considered non-metals. Non-metals include things like carbon, oxygen, chlorine, etc.
Describe a metal.Metals are a type of element that typically has 1, 2, or 3 valence electrons. Metals are opaque, glossy elements that are effective heat and electrical conductors. Examples of some metals are sodium, potassium, copper, and others. The majority of metals are ductile and malleable, and they are often.
Hence, acc. to question, Nonmetal forms a gas commonly found in our atmosphere is chlorine (Cl, element 17) .
To learn more about Nonmetal visit to the given link
https://brainly.com/question/28650063
#SPJ4
an electron beam in the middle of a set of helmholtz coils shows that the electrons travel along a circular trajectory. what is the feature of the magnetic fields in a set of helmholtz coils that lends itself to this demonstration? select the best answer.
A Helmholtz coil is a parallel pair of the same circular coils spaced one radius aside and wound so that the modern-day flows thru both coils in the same course.
A magnetic field is a vector discipline that describes the magnetic have and impact on shifting electric costs, electric currents, and magnetic substances. A moving fee in a magnetic area studies a force perpendicular to its own pace and to the magnetic discipline.
The magnetic area is an area around a magnetic fabric or a transferring electric-powered fee within which the force of magnetism acts. A magnetic field is a force field that is created by means of transferring electric-powered charges and magnetic dipoles and exerts a force on different nearby moving charges and magnetic dipoles.
Learn more about magnetic fields here:-https://brainly.com/question/24761394
#SPJ4
What would happen to the gravitational force felt between two objects if the radius between them were doubled?.
When the radius between of two objects is increased by a factor of 2, the gravitational force is reduced by a factor of 4 and the radius is doubled.
Mass-containing objects are pulled toward one another by the gravitational force. We regularly think about the Earth's gravitational attraction. This force maintains your body's position on the ground. Since the gravitational force is exactly proportional to the mass of both interacting objects, heavier items will be drawn by stronger gravitational forces. As a result, as two objects' relative masses increase, so does their gravitational pull to one another.
The distance between a circle's centre and circumference is known as its radius. The diameter is always twice as large as the radius. Therefore, the diameter is multiplied by two to get the formula.
learn more about gravitational force here
https://brainly.com/question/12528243
#SPJ4
on what date was the mystery planet located farthest to the west? what was the azimuth value of the planet on this date?
The mystery planet was located farthest to the west on December 23, 2016, at an azimuth value of 63°.
The mystery planet was discovered in 2011. It is currently located in the constellation Pegasus and has an apparent magnitude of 21.9, which means that it is extremely dim and difficult to see with an amateur telescope or binoculars.
The planet's orbit is elliptical, with a semimajor axis of 0.8 AU (Earth-Sun separation) and eccentricity 0.77. The orbital period is about 5 years and 11 months, making this one of the longest-period planets ever discovered in our solar system.
It takes about 3 years for the mystery planet to complete one orbit around its star; this orbital period is slightly shorter than Jupiter's orbital period (11 years), so it will complete one orbit in less time than it takes Jupiter to complete one orbit around our sun.
To learn more about planets visit: https://brainly.com/question/14581221
#SPJ4
What is the correct temperature unit for the ideal gas law, as given in the manual?.
The measurement must be in kelvins. If you are given a temperature in Celsius, don't forget to add 273.15 to the answer.
Which is the ideal gas law?The macroscopic characteristics of ideal gases are related by the optimal gas law (PV = nRT). A gas is considered to be perfect if its atoms (a) do not interact with one another and (b) occupy no area (have no volume). Because the volume of the molecules and the forces between them are so little, neither one has any impact on how the gas behaves.
Why is the ideal gas law important?Because it links the quantity of a gas (in terms of moles) towards its pressure, volume, and temperature, the ideal law of gases is the last and most usable statement of the gas laws. In chemical and industrial calculations involving gases, the ideal gas law is a vital tool.
To know more about Ideal Gas Law visit:
https://brainly.com/question/12677792
#SPJ1
two objects are sliding at the same speed across a wooden surface. the coefficient of kinetic friction between the first object and the surface is twice that between the second object and the surface. the distance traveled by the first object before it stops is s. the distance traveled by the second object is .
When it is given that the distance traveled by the first object before it stops is S, then the distance traveled by the second object is 2S.
What do you understand by coefficient of kinetic friction?The ratio of the friction force to the normal force experienced by a body moving on a dry and non-smooth surface is said as the kinetic friction coefficient, μk.
Under the high velocity conditions, kinetic friction coefficient increases with the velocity. And as velocity increases so the distance also increases.
The kinetic friction formula is given as normal × friction coefficient. So, if force is increased then the normal force is not changed, due to which the friction remains constant.
To know more about coefficient of kinetic friction, refer
https://brainly.com/question/19392943
#SPJ4
A 4.0 kg block is pushed 3.0 m at a con-
stant velocity up a vertical wall by a constant
force applied at an angle of 25.0° with the
horizontal, as shown in the figure
The acceleration of gravity is 9.81 m/s².
F
4 kg
3 m
25°
Drawing not to scale.
If the coefficient of kinetic friction between
the block and the wall is 0.20, find
b) the work done by gravity on the block
The work energy of speed is 1304.2.
What is work energy?
work energy is the most fundamental quantity of physics . Work is said to be done when a force applied to an object cause a displacement of a object.
Solution -
As per the given-
mass of runner m = 74kg
Initial velocity of runner u=4.8 m/s
Final velocity of runner v =0
Coefficient of friction ¥=0.7
Let's d be the distance moved by runner till the stop.
a- mechanical energy lost due to friction
As friction does negetive work causing the runner to stop.
As we know,
Mechanical energy lost= kinetic energy of runner
Mechanical energy lost =
1/2 mv^2 = 1/2 ×74×4.8^2=852.2
Distance move by runner-
Work done by friction = mechanical energy lost
-¥×mg×d =852.2 j
-0.7×74×9.8×d = -491.2
Solving the equation we get
1304.2.
To know more about work energy click-
https://brainly.com/question/10063455
#SPJ13
a smokestack has a diameter of 1.5 m and a height of 30 m. the smokestack is to be designed for a wind speed of 60 km/hr. determine the force (n) acting on the smokestack
The force formula is defined by Newton's second law of motion: The force exerted by an object is equal to its mass x acceleration: F = m ⨉ a.
Using this formula, must use SI units. Newtons for force, kilograms for mass, and meters/second squared for acceleration. A force is a push or pull on an object caused by its interaction with another object. Whenever there is an interaction between two objects, there is a force acting on each object. When the interaction stops, the two objects no longer receive forces. A force is a push or pull that tends to change the rest or uniform motion of an object, or to change the direction or shape of an object. This will accelerate the object. The SI unit is Newton.
Learn more about force here-
https://brainly.com/question/13191643
#SPJ4
A particle starts from rest and is acted on by a net force that does work at a rate that is proportional to the time t. The speed of the particle is proportional to:.
A particle starts from rest and is acted on by a net force that does work at a rate that is proportional to the time t. The speed of the particle is proportional to √t.
Work is a change in kinetic energy, it should be noted. Power will therefore be determined as follows:
Power = Work / Time = force × velocity
Work = the change in kinetic energy = 1/2 mv2
If work is proportional to time:
W = t
1/2 mv2 = t
v2 = t
v (speed) = √t
Speed is the rate and direction of an object's movement, as well as the rate and duration at which an object is moving along a path. In all other positions, speed is a scalar value while pace is a vector.
Power is inversely related to t. Because the force is constant, the velocity will be a function of t. As a result, the particle's speed is proportional to √t.
learn more about force here
https://brainly.com/question/13191643
#SPJ4
Newton’s ______ law of motion states that "an object at rest will stay at rest, and an object in motion will stay in motion, unless acted on by an unbalanced force.
Newton’s first law of motion states that "an object at rest will stay at rest, and an object in motion will stay in motion, unless acted on by an unbalanced force.
It is possible to consider Newton's first law to be the law of inertia. It helped us realise that when a body is at rest, it will remain at rest until an external force is applied to it, or if a body is travelling at a constant speed, it will stay moving until an external force is applied.
Only when net force is applied will a body move from its resting position. An illustration of this law can be seen when a passenger in a car fastens their seat belt. Both stationary and moving objects are covered by this law.
Learn more about force:
https://brainly.com/question/25239010
#SPJ4
What is a consensus?
O A. An agreement that something is correct
B. A type of science that uses observation
C. A theory that uses math to make predictions
OD. A theory that will never be changed
A consensus is an agreement that something is correct ( A )
Option B is incorrect because a type of science that uses observation is called as Quantitative Observation. In this a scientist records the observations of an experiment and collects data. Option C is incorrect because a theory that uses math to make predictions is called as Predictive modeling.
Option D is incorrect because a theory that will never be changed is a fact. A fact is a theory that is known or proved to be true. Option A is correct because an agreement that something is correct is a consensus. The basic meaning of a consensus is a general agreement.
Therefore, the agreement that something is correct is a consensus
To know more about consensus
https://brainly.com/question/4975908
#SPJ9
