Question 2 - Choose resistances for a voltage divider. Please provide any references/sources used. The following schematic shows a simple voltage divider used to measure a signal that is expected to b

Using the given values of the power supplied to the motor (80 kW), torque angle (250 degrees converted to radians), and voltage at the terminals, we can calculate the armature current at the load condition (Ia = IaLO).

To calculate the magnitude of the internal generated voltage (Ea) and the armature current (Ia = IaLO), we can use the following formulas:

a) Magnitude of the internal generated voltage (Ea):

The magnitude of the internal generated voltage can be calculated using the formula:

Ea = (P / (3 * √3 * IaLO * cos(θ))) + V

where:

P = Power supplied to the motor (in watts)

IaLO = Armature current at the load condition (in amperes)

θ = Torque angle (in radians)

V = Voltage at the terminals of the motor (in volts)

Given that the power supplied to the motor is 80 kW (80,000 watts), and the torque angle is 250 degrees (converted to radians), you can substitute these values into the formula along with the other known values (such as the voltage at the terminals) to calculate the magnitude of the internal generated voltage (Ea).

b) Armature current at the load condition (Ia = IaLO):

The armature current at the load condition can be calculated using the formula:

IaLO = P / (3 * √3 * V * cos(θ))

where:

P = Power supplied to the motor (in watts)

V = Voltage at the terminals of the motor (in volts)

θ = Torque angle (in radians)

Using the given values of the power supplied to the motor (80 kW), torque angle (250 degrees converted to radians), and voltage at the terminals, you can calculate the armature current at the load condition (Ia = IaLO).

Learn more about armature current from the given link!

https://brainly.in/question/50692921

#SPJ11

According to the law of conservation of energy, the total initial energy should be equal to the final energy.

Based on the given information, we can analyze the situation using principles of energy conservation and Hooke's Law for the spring.

Potential Energy:

The potential energy of the box can be calculated using the formula:

Potential Energy = m * g * h,

where m is the mass of the box (0.5 kg), g is the acceleration due to gravity (9.8 m/s²), and h is the change in height (30 cm - 20 cm = 10 cm = 0.1 m).

Potential Energy = 0.5 kg * 9.8 m/s² * 0.1 m = 0.49 J.

Spring Potential Energy:

The spring potential energy can be calculated using the formula:

Spring Potential Energy = (1/2) * k * x²,

where k is the spring constant (120 N/cm = 120 N/m = 12,000 N/m) and x is the change in length of the spring.

Change in length of the spring, x = final length - initial length = (30 cm - 40 cm) = -10 cm = -0.1 m (negative sign indicates compression).

Spring Potential Energy = (1/2) * 12,000 N/m * (-0.1 m)² = 60 J.

Total Initial Energy:

The total initial energy of the system is the sum of the potential energy and the spring potential energy when the box is at rest:

Total Initial Energy = Potential Energy + Spring Potential Energy = 0 + 60 J = 60 J.

Final Energy:

The final energy of the system is the potential energy when the box reaches the new height:

Final Energy = Potential Energy = 0.49 J.

To learn more about final energy

https://brainly.com/question/29413600

#SPJ11

Complete Answer:

A Spring With An Unstretched Length Of 40 Cm And A K Value Of 120 N/Cm Is Used To Lift A 0.5 Kilogram Box From A Height Of 20 Cm To A Height Of 30 Cm. If The Box Starts At Rest, What Would You Expect The Final Velocity To Be?

A spring with an unstretched length of 40 cm and a k value of 120 N/cm is used to lift a 0.5 kilogram box from a height of 20 cm to a height of 30 cm. If the box starts at rest, what would you expect the final velocity to be?

The mutual inductance between two coils is the measure of their ability to induce an electromotive force (emf) in each other.

Faraday's law of induction states that a changing magnetic field induces an emf in a nearby coil. In this scenario, when the current in one coil is switched off, it results in a changing magnetic field. This changing magnetic field induces an emf in the other coil due to their close proximity. The magnitude of this induced emf is directly proportional to the rate of change of magnetic flux linking the second coil.

The value of mutual inductance quantifies the strength of the coupling between the two coils. It depends on factors such as the number of turns in each coil, their relative orientation, and the distance between them. By measuring the induced emf in the second coil and knowing the rate of change of current in the first coil, the mutual inductance can be determined using Faraday's law. Mutual inductance is an important concept in understanding electromagnetic phenomena and is widely used in various applications, including transformers, motors, and generators.

To know more about mutual inductance click here:

https://brainly.com/question/28585496

#SPJ11

The current contained within the width of a thin ring concentric with the wire, with a radial width of 14.0 μm and at a radial distance of 1.20 mm, can be determined by integrating the current density function over the area of the ring.

To calculate the current, we need to find the area of the ring first. The area of the ring can be approximated as the difference between the areas of two concentric circles: the outer circle with a radius of (1.20 mm + 7.00 μm) and the inner circle with a radius of (1.20 mm - 7.00 μm).

The outer radius of the ring is (1.20 mm + 7.00 μm) = 1.207 mm = 0.001207 m.

The inner radius of the ring is (1.20 mm - 7.00 μm) = 1.193 mm = 0.001193 m.

The area of the ring is then given by:

A = π * (outer radius)^2 - π * (inner radius)^2.

Substituting the values:

A = π * (0.001207 m)^2 - π * (0.001193 m)^2.

Now, we can calculate the current within the ring by multiplying the area with the current density at the radial distance:

Current = J(r) * A.

The current density, J(r), is given as J(r) = Br, where B = 1.95 × 10^5 A/m^3.

Substituting the values:

Current = (1.95 × 10^5 A/m^3) * (0.001207 m - 0.001193 m).

Learn more about current here:-

https://brainly.com/question/32059694

#SPJ11

The magnitude of the charge accumulated on each of the oppositely charged plates is approximately 5.4888 * 10⁽⁻¹⁰⁾ C.

To find the electric field in the region between the two plates of a capacitor, we can use the formula:

E = V / d

where E is the electric field, V is the potential difference (voltage) between the plates, and d is the distance between the plates.

V = 8.0 V

d = 0.80 cm = 0.80 * 10⁽⁻²⁾ m

Plugging in these values into the formula:

E = 8.0 V / (0.80 * 10⁽⁻²⁾ m)

E = 8.0 V / 0.008 m

E = 1000 V/m

Therefore, the electric field in the region between the two plates is 1000 V/m.

To find the charge magnitude Q accumulated on each of the oppositely charged plates, we can use the formula:

Q = C * V

where Q is the charge, C is the capacitance, and V is the potential difference (voltage) between the plates.

The capacitance of a parallel-plate capacitor is given by the formula:

C = ε₀ * A / d

where ε₀ is the permittivity of free space, A is the area of each plate, and d is the distance between the plates.

A = 0.78 m²

d = 0.80 cm = 0.80 * 10⁽⁻²⁾ m

Substituting these values into the capacitance formula:

C = (8.85 * 10⁽⁻¹²⁾⁾ F/m) * 0.78 m² / (0.80 * 10⁽⁻²⁾⁾m)

C ≈ 6.861 * 10⁽⁻¹¹⁾ F

Plugging the capacitance and the potential difference into the charge formula:

Q = (6.861 * 10⁽⁻¹¹⁾ F) * 8.0 V

Q = 5.4888 * 10⁽⁻¹⁰⁾ C

To know more about  charge refer here

brainly.com/question/14692550

#SPJ11

Complete Question : A capacitor is constructed with two parallel metal plates each with an area of 0.83 m 2 and separated by d=0.80 cm. The two plates are connected to a 9.0-volt battery. The current continues until a charge of magnitude Q accumulates on each of the oppositely charged plates. Find the electric field in the region between the two plates. V. /m Find the charde Q.

Therefore, the speed of the wave is 0.5 m/s. The amplitude of the wave is 0.120 m, and the frequency is 2 Hz.  The amplitude of the wave is 0.120 m, and the wavelength is 0.25 m.

To determine the speed of the wave, we can use the equation v = λf, where v is the speed of the wave, λ is the wavelength, and f is the frequency.

In the given wave function y = (0.120 m)sin(8πx + 4πt), the coefficient in front of the argument of the sine function (8π) represents the wave number, k, which is related to the wavelength by the equation λ = 2π/k.

So, in this case, the wavelength is λ = 2π/(8π) = 1/4 = 0.25 m.

The frequency, f, can be determined from the coefficient in front of t in the argument of the sine function (4π). Since the general form of the wave equation is y = A sin(kx - ωt), where ω is the angular frequency, we can relate the angular frequency to the frequency by the equation ω = 2πf.

In this case, ω = 4π, so the frequency is f = ω/(2π) = 4π/(2π) = 2 Hz.

Now we can calculate the speed of the wave using v = λf:

v = 0.25 m × 2 Hz = 0.5 m/s

Therefore, the speed of the wave is 0.5 m/s.

b) To draw a history graph for the wave function at position x = 8 meters, we fix x = 8 in the equation y = (0.120 m)sin(8πx + 4πt) and plot y as a function of t.

The history graph will show how the wave oscillates over time at the specified position. The amplitude of the wave is 0.120 m, and the frequency is 2 Hz.

c) To draw a snapshot graph for the wave function at moment t = 0 s, we fix t = 0 in the equation y = (0.120 m)sin(8πx + 4πt) and plot y as a function of x.

The snapshot graph represents the shape of the wave at a specific instant in time. In this case, we are considering the wave at t = 0 s. The amplitude of the wave is 0.120 m, and the wavelength is 0.25 m.

To know more about wave function:

https://brainly.com/question/28446841

#SPJ4

The average current drawn by the cell phone when turned on is approximately 0.45 A

We have the following information:

The rated voltage of the cell phone battery is V = 3.70 V.

The amount of electrical energy that can be produced by the battery is E = 3.15 × 104 J.

The duration for which the battery can produce electrical energy is t = 5.25 hours.

Conversion of time to seconds:1 hour = 60 minutes

1 minute = 60 seconds

Therefore, 5.25 hours = 5.25 × 60 × 60 seconds = 18,900 seconds.

The average current drawn by the cell phone when turned on is given by the formula: I = ΔQ/Δt

Where, ΔQ is the charge in coulombs and Δt is the time in seconds.

The electrical energy E produced by the battery is given by:E = VQQ = E/V

Substituting the given values, we get:Q = (3.15 × 104 J)/(3.70 V) = 8513.5 C

Therefore, the average current drawn by the cell phone is:

I = ΔQ/Δt = 8513.5 C/18,900 s = 0.45 A (approximately)

Learn more about electrical energy at

https://brainly.com/question/15174073

#SPJ11

Pulse duration, t₁ = 1 ns Peak power,

P₁ = 100 kW Pulse duration,

t₂ = 10 ns The peak transmit power when the pulse is expanded to 10 ns is to be determined. Concept:

Peak power of a signal is inversely proportional to its pulse duration. It is given by:

P = k / t where k is a constant. The pulse duration and peak power of a signal are related by:

P₁ x t₁ = P₂ x t₂ Calculation:

P₁ x t₁ = P₂ x t₂⇒ 100 k

W x 1 ns = P₂ x 10 ns⇒

P₂ = 10 kW The peak transmit power when the pulse is expanded to 10 ns is 10 kW. Explanation:

Given, a pulse of duration 1 ns and peak power of 100 kW. The peak power is inversely proportional to the pulse duration. So, the peak power reduces if the pulse duration increases.

In this case, the pulse duration has increased to 10 ns. Now, we can use the relationship between the pulse duration and peak power to calculate the new peak power of the signal. The product of the peak power and the pulse duration remains constant.  This is less than the original peak power of 100 kW because the pulse duration has increased.

To know more about duration visit:

https://brainly.com/question/32886683

#SPJ11

1).

Clo is defined as a unit used to measure the thermal resistance or insulation of a fabric or garment. Clo values are used to determine the thermal resistance of fabrics or garments.

Clo values are commonly used to determine how warm a garment or fabric is and what temperature it can maintain. For instance, a 1 clo value is equal to the thermal resistance of typical indoor clothing. The below are two examples of Clo values:

- A winter jacket with a 3 clo value has a thermal resistance that is three times greater than indoor clothing.
- A sleeping bag with a 6 clo value can keep someone warm in temperatures below freezing.

2).  

There are five factors that can cause a human to interpret a noise source as ‘nuisance noise’ in relation to environmental noise. These factors are as follows:

- Volume: the louder a noise is, the more likely it is to be considered a nuisance.
- Tone: the pitch of a sound can make it more unpleasant or irritating.
- Source: the closer the sound source is to someone, the more likely it is to be a nuisance.
- Duration: the longer a sound lasts, the more likely it is to be considered a nuisance.
- Time: The time of day or night can influence how someone perceives a noise. Nighttime sounds are more likely to be considered a nuisance than daytime sounds.

3).

To calculate the value of X, use the formula:

L1 + L2 + L3 + ... = 10 log10 (I1/I0 + I2/I0 + I3/I0 + ...)

where L is the sound level, I is the sound intensity, and I0 is the standard reference intensity of 10-12 W/m2.

- For 57 dB + 57dB = X,
57 dB + 57 dB = 114 dB
10 log10 (I1/I0 + I2/I0)
10 log10 (10-3/10-12 + 10-3/10-12)
= 116 dB

Therefore, the value of X is 116 dB.

- For 62 dB + 62 dB + 65 dB = X,
62 dB + 62 dB + 65 dB = 189 dB
10 log10 (I1/I0 + I2/I0 + I3/I0)
10 log10 (10-3/10-12 + 10-3/10-12 + 3.16 x 10-3/10-12)
= 191 dB

Therefore, the value of X is 191 dB.

- For 86 dB +28 dB = X,
86 dB + 28 dB = 114 dB
10 log10 (I1/I0 + I2/I0)
10 log10 (10-3/10-12 + 10-2/10-12)
= 116.5 dB

Therefore, the value of X is 116.5 dB.

To know more about  sound intensity visi:

https://brainly.com/question/14349601

#SPJ11

Using the given formula;Re = (789 kg m) (0.298333 m³ s⁻¹) (60 m) / (4.13 CP -3)Re = 11,347As the Reynold's number (Re) is greater than 4000, the flow is turbulent. So, the flow is turbulent.

Reynold's number is used to identify whether the flow is laminar or turbulent. The formula to find the Reynold's number is given by:Re = ρvd/μWhereRe = Reynold's numberρ = density of the fluidv = velocity of the

fluid = diameter of the pipemu

(μ) = Viscosity of the fluid laminar flow is when Re < 2000

Turbulent flow is when Re > 4000

Transitional flow is when 2000 < Re < 4000 Given data, Orange juice concentrate is flowing at 0.298333 m³ s-1 in a 60 m diameter pipe.

Viscosity of orange juice concentrate at 40 °C = 4.13 CP -3

Density of orange juice concentrate at 40°C = 789 kg m

Temperature of juice concentrate = 40°C.Using the given formula;

Re = (789 kg m) (0.298333 m³ s⁻¹) (60 m) / (4.13 CP -3)

Re = 11,347As Reynold's number (Re) is greater than 4000, the flow is turbulent. So, the flow is turbulent.

To know more about Reynold's number visit:

brainly.com/question/31298157

#SPJ11

The correct answer is: b) Receding from Earth.

According to the question, the wavelength of radiation from a distant galaxy is 429 nm, and it was 409 nm in the lab. Therefore, the redshift is z = 429/409 - 1 = 0.0489a)

To determine the radial speed of the galaxy relative to the earth, we'll use the formula:v = zc where v is the radial velocity, z is the redshift, and c is the speed of light.

Substitute the values: v = (0.0489)(3 x 10^5 km/s) ≈ 14,670 km/s

Therefore, the radial velocity of the galaxy relative to the Earth is approximately 14,670 km/s.

b) The galaxy is receding from Earth because the value of z is positive.

To know more about radial speed please refer:

https://brainly.com/question/25279049

#SPJ11

The maximum coefficient of performance (COP) for a freezer that is set to maintain the cold space at -1.4°F, which is located in a kitchen that is maintained at 76° F is given as 4.05.

A freezer is an electronic device that is used to keep food and other perishable things at a very low temperature. This device keeps food and other things from spoiling due to the low temperature that is being maintained in the freezer.

Coefficient of Performance (COP) is defined as the ratio of the heat that is moved from the low-temperature environment to a high-temperature environment to the amount of work that is done by a refrigeration unit or device.

The maximum coefficient of performance (COP) for a freezer that is set to maintain the cold space at -1.4°F, which is located in a kitchen that is maintained at 76° F is given by

COP = (Th/Tl - 1) = (76 + 459.67)/(-1.4 + 459.67) - 1

= 4.05 (approx.)

Therefore, the maximum coefficient of performance (COP) for a freezer that is set to maintain the cold space at -1.4°F, which is located in a kitchen that is maintained at 76° F is given as 4.05.

learn more about freezer here

https://brainly.com/question/31408301

#SPJ11

Two steel conductors are bent into rectangular prisms with square bases of lengths a and I, where l=2a. If the thin prism has a length of L1=10a and the thick prism has a length of L2=40a; compare the resistances of the two conductors:

The thinner conductor has smaller resistance, so option A is correct.Conductors are materials that have a low resistance to the flow of electric current. A rectangular prism is a three-dimensional shape that has six faces, each of which is a rectangle. Square bases have sides of the same length.

The thinner conductor has a lower resistance compared to the thicker conductor because resistance increases as the length of the conductor increases, all other factors remaining constant. The resistance of a conductor depends on three things, namely, its length, cross-sectional area, and material of construction.

The greater the length of a conductor, the greater its resistance, as its cross-sectional area remains the same.The thin prism has a length of L1=10a, and the thick prism has a length of L2=40a.

To know more about rectangular visit:

https://brainly.com/question/32444543

#SPJ11

The maximum number of appliances that can be plugged into the sockets of that circuit before the circuit breaker trips is 4 whole numbers.

Given data: The voltage of circuit, V = 120 V

The current at which circuit breaker will trip, I = 20 A

The power of each appliance, P = 515 W

To find: The number of appliances that can be plugged into the sockets of that circuit before the circuit breaker trips.

Formula:The current through the circuit can be found as follows;

I = P / V Where P is the power of the appliance and V is the voltage of the circuit.

Substituting the given values

I = 515 W / 120 VI = 4.29 A (approx)

The maximum number of appliances can be calculated as follows;

N = I / n Where I is the current of the circuit and n is the current consumption of a single appliance.

N = 20 A / 4.29 AN = 4.66 (approx)

To know more about  circuit  visit:-

https://brainly.com/question/12608491

#SPJ11

The output of the filter can be found out by first calculating the Fourier transform of the input signal x(t) and then multiplying it with the frequency response of the filter

Y(jω) = 0.3π(δ(ω - 31) + δ(ω + 31)) - 0.3jπ(δ(ω - 31) + δ(ω + 31)) - 0.15[δ(ω - 4) - δ(ω + 4)]

The input signal

x(t) = 2cos(31t) - 3sin(4t)

is to be filtered using an ideal high pass filter that has a cutoff angular frequency of 5 rad/sec and a passband gain of 1, and the output of the filter is to be found out. The units of the time variable r and angular frequency ω in this IRA are in seconds and rad/second, respectively. IRA#6_1.

The highpass filter can be defined as having the frequency response

H(jω) = (jω/5 + 1) / (jω + 5).

Here, j is the imaginary unit, ω is the angular frequency in rad/sec, and 5 is the cutoff angular frequency of the filter, which is 5 rad/sec. Since this is an ideal highpass filter, its gain is unity in the passband (angular frequencies greater than 5 rad/sec) and zero in the stopband (angular frequencies less than 5 rad/sec).

The output of the filter can be found out by first calculating the Fourier transform of the input signal x(t) and then multiplying it with the frequency response of the filter

H(jω).x(t) = 2cos(31t) - 3sin(4t)X(jω) = [π(δ(ω - 31) + δ(ω + 31))] / 2j - 1.5[δ(ω - 4) - δ(ω + 4)]

Now, the output of the filter Y(jω) can be obtained as follows.

Y(jω) = H(jω)X(jω)

= [(jω/5 + 1) / (jω + 5)][π(δ(ω - 31) + δ(ω + 31))] / 2j - 1.5[δ(ω - 4) - δ(ω + 4)]
The final answer is:

Y(jω) = 0.3π(δ(ω - 31) + δ(ω + 31)) - 0.3jπ(δ(ω - 31) + δ(ω + 31)) - 0.15[δ(ω - 4) - δ(ω + 4)]

To know more about Fourier transform visit:

https://brainly.com/question/1542972

#SPJ11

The strength of the magnetic field is approximately 1.6 x 10^(-4) Tesla.

The strength of the magnetic field can be determined using the formula:

E = B * L * v

Where:
E is the induced emf (0.37 V)
B is the strength of the magnetic field (unknown)
L is the length of the rod (0.70 m)
v is the velocity of the rod (1.9 mi/s)

First, we need to convert the velocity from miles per second to meters per second. There are 1609.34 meters in one mile, so:

v = 1.9 mi/s * 1609.34 m/mi = 3058.75 m/s

Now we can rearrange the formula to solve for B:

B = E / (L * v)

Substituting the given values:

B = 0.37 V / (0.70 m * 3058.75 m/s)

Calculating the numerator and denominator separately:

B = 0.37 / (0.70 * 3058.75) V * m / (m * s)

B ≈ 1.65 x 10^(-4) V * m / (m * s)

Finally, rounding to two significant figures:

B ≈ 1.6 x 10^(-4) T

Therefore, the strength of the magnetic field is approximately 1.6 x 10^(-4) Tesla.

Learn more about the magnetic field

https://brainly.com/question/26257705

#SPJ11

The steady-state maximum power that the machine can deliver before losing synchronism is given by the formula Pmax=EbVtXS×sinδWhere Eb is the voltage induced in the field winding of the generator. Since the field current is not given, we cannot calculate Eb directly.

However, we can use the fact that the maximum power occurs when δ is 90°. This is because sinδ is maximum at 90°. Therefore, we can write Pmax=EbVtXS×1

=EbVtXS

=24000×0.8

=19,200 kVA The armature current corresponding to this maximum power isIamax

=Pmax/√3VtCosϕ

=19,200×103/√3×24,000×0.8

=0.925 kA

The reactive power corresponding to this maximum power is Q=EbVtXS×cosδ

=24000×0.8×0.6

=11,520 kVAr The phasor diagram for the generator operating at maximum power is shown below:

Figure:

Phasor diagram of generator operating at maximum power

To know more about maximum visit:

https://brainly.com/question/30693656

#SPJ11

The velocity of the car relative to the train is 40 mph and the velocity of the walker relative to the train is 78 mph. The train rider is the correct one because they chose the frame of reference, and therefore their velocity is 0 mph.

1. Frame of reference and relative velocity The relative velocity of two objects is the velocity of one with respect to the other. The frame of reference chosen will be that of the train because it is traveling the fastest, and the velocities of the other two members of the group will be calculated with respect to the train rider. The velocity of the car relative to the train will be the difference in their velocities, which is 80-40 = 40 mph. Similarly, the velocity of the walker relative to the train is 80-2 = 78 mph.

2. Throwing sandwich The answer is no. When the car passes the train, it is also moving at a speed of 80 mph, so the sandwich will not be able to keep up with the train rider's speed of 80 mph. As a result, the sandwich will be thrown in the direction of the train and will not reach the train rider.

3. Velocity observed by group members According to the train rider, the velocity of the ball is (0, -vy). As observed by the car, the velocity of the ball will be (40, -vy). Finally, as observed by the walker, the velocity of the ball will be (78, -vy).

4. Velocity vector and speedThe velocity vector of the ball as observed by the train-rider is in the downward direction (0, -vy). As observed by the car, the velocity vector will be pointing in the downward direction and slightly to the right of the car (40, -vy). Finally, as observed by the walker, the velocity vector will be pointing in the downward direction and slightly to the right of the walker (78, -vy). According to the three group members, the ball is moving in a downward direction with different horizontal velocities. However, the speed of the ball is the same according to all three group members. The train-rider is correct because they chose the frame of reference, and therefore their velocity is 0 mph.

To know more about relative velocity please refer:

https://brainly.com/question/17228388

#SPJ11

We need to find the net force experienced by q3. Let's find the electrostatic force between q3 and q1 and q3 and q2 using Coulomb's Law.

The force experienced by q3 due to q1 is given by,

[tex]f1-3 = k * q1 * q3 / d1-3f1-3 = 9 * 10^9 * -15 * 10^-9 * 5 * 10^-9 / 2f1-3 = -33.75 N[/tex]

The force experienced by q3 due to q2 is given by,

[tex]f2-3 = k * q2 * q3 / d2-3f2-3 = 9 * 10^9 * 20 * 10^-9 * 5 * 10^-9 / 6f2-3 = 15 N[/tex]

Step 2: Let's find the direction of the forces.

f1-3 acts towards the left and f2-3 acts towards the right

Step 3:

Fnet = f1-3 + f2-3

Fnet = -33.75 + 15

Fnet = -18.75 N

Hence, the option is D.

To know more about electrostatic visit:

https://brainly.com/question/16489391

#SPJ11

The mass of 14C required is,m = 2.74 × 10-21 mol × 14 g/mol=3.84×10−20 kg

Radioactivity refers to the process by which the nucleus of an atom of an unstable isotope releases energy in the form of radiation. It has three types, namely: alpha decay, beta decay, and gamma decay.

ActivityThe activity is the rate at which radioactive nuclei undergo decay. It is the number of disintegrations per second of a sample of radioactive material. It is measured in Becquerels (Bq) or Curie (Ci).

The formula for calculating activity is given as,A=λNWhere A represents activity (Bq), λ represents the decay constant, and N represents the number of radioactive nuclei present.

 Half-lifeIt is defined as the time taken for the activity of a radioactive sample to fall to half of its original value. It is denoted by the symbol T1/2.

The formula for calculating half-life is given as,T1/2=ln2λ

CalculationThe mass of 14C required to provide an activity of 7.57 nCi is to be calculated.

Therefore, the first step is to convert the activity to Becquerels.

The conversion factor is, 1 Ci = 3.7 × 1010 Bq7.57 n

                                       Ci = 7.57 × 10-9

                                         Ci=7.57 × 10-9 Ci×3.7 × 1010 Bq/Ci = 2.80 × 102 Bq

The next step is to calculate the number of radioactive nuclei present.

The formula is given as,A=λNN=A/λN = (2.80 × 102)/ (ln2/5730)=1.90 × 1012

The mass of 14C required to provide an activity of 7.57 nCi is given as,m = N × Mwhere M is the molar mass and N is the number of moles.

The molar mass of 14C is 14 g/mol.

The number of moles of 14C is,3.84×10−20 kg ÷ 14 g/mol=2.74 × 10-21 mol

Therefore, the mass of 14C required is,m = 2.74 × 10-21 mol × 14 g/mol=3.84×10−20 kg

Hence, the answer is 3.84×10−20 kg.

Learn more about Radioactivity

brainly.com/question/1770619

#SPJ11

The problem considers a clear liquid in an open container. The critical angle for the liquid-air interface is 48 degrees. Now, when light is directed at the container from above, its angle of incidence (0₂) is varied.

At an angle of incidence 0₂, an orientation (0₁=0) can be found where OP makes an angle 0 with the normal to the surface. OP is the distance that is parallel to the surface between the entry and exit points of the light beam. The task is to find the value of OP when 0₂=50 degrees.

In the case of refraction, Snell's law applies, which is defined as $n_1 sin(θ_1) = n_2 sin(θ_2)$Here, θ1 and θ2 denote the angles of incidence and refraction, respectively, n1 and n2 denote the refractive indices of the first and second media, respectively, and sin is the trigonometric function.

The critical angle for the liquid-air interface is given by sin(θ_c) = n_air/n_liquid.  The value of θ_c is 48°. Let us consider a light ray incident at an angle 0₂ from the vertical in the liquid

To know more about critical visit:

https://brainly.com/question/15091786

#SPJ11

1. The ball has an upward displacement of 0.5835 m.

2.  time of flight  = 0.239 s`

3.  the ball's net displacement is zero.

1. Calculation of displacement of the ball in the upward direction:

Given that a ball is thrown into the air with a speed of 2.35 m/s (upon release), and then caught. The motion is symmetric, and without air resistance. Therefore, the ball has the same speed when it is caught, as when it was thrown, assuming it is caught at the same height it was released.The upward velocity will decrease as the ball goes up, and it will eventually come to a stop at the highest point of its trajectory and begin falling back down. At the highest point, the velocity will be zero and the displacement of the ball will be maximum. Also, the displacement of the ball at the highest point is equal to the displacement of the ball at the instant it was thrown upwards. Therefore, the ball has an upward displacement of 0.5835 m.

2. Calculation of the ball's time of flight in the upward direction

:Time of flight in the upward direction is given by;

`t = v/g`

Where

t = time,

v = initial velocity

= 2.35 m/s, and

g = acceleration due to gravity

= 9.8 m/s²

`t = 2.35/9.8

= 0.239 s`

3. Calculation of the ball's total time of flight:

Since the ball has the same speed when it is caught as when it was thrown and assuming it is caught at the same height it was released, the total time of flight is two times the time of flight in the upward direction.

`Total time of flight = 2 x t``= 2 x 0.239`

`= 0.478 s`4.

Calculation of the ball's net displacement:

Since the displacement of the ball in the upward direction is 0.5835 m, the net displacement of the ball is zero because it returns to its initial position. Hence, the ball's net displacement is zero.

To know more about displacement visit:

https://brainly.com/question/11934397

#SPJ11

The height of the mercury column is 0.00416 m. A manometer is an instrument that uses fluid columns to measure pressure or pressure differences. It is the most accurate way to measure gauge pressure. The most common type of manometer is the mercury manometer. It is used to measure low-pressure differences in liquids and gases.

In this problem, we are given a multifluid manometer with water and mercury. We are asked to determine the height h of mercury in the manometer. We are also given that the oil (aceite) has a relative density of 0.8, and the density of water (agua) is 1000 kg/m3.

The pressure difference between the two sides of the manometer is given by the difference in the heights of the two columns of fluid. Let h1 be the height of the water column, and h2 be the height of the mercury column.

We know that the pressure at the bottom of the manometer is the same on both sides. Therefore, we can write:

ρwater * g * h1 = ρmercury * g * h2 + ρoil * g * h3

where ρwater is the density of water, ρmercury is the density of mercury, ρoil is the density of oil, and h3 is the height of the oil column.

Since the oil has a relative density of 0.8, its density is:

ρoil = 0.8 * ρwater = 0.8 * 1000 kg/m3 = 800 kg/m3

Substituting this value into the equation, we get:

1000 * 9.8 * 0.25 = 13600 * 9.8 * h2 + 800 * 9.8 * 0.15

Solving for h2, we get:

h2 = (1000 * 9.8 * 0.25 - 800 * 9.8 * 0.15) / (13600 * 9.8)

h2 = 0.00416 m

Therefore, the height of the mercury column is 0.00416 m.

To learn more about mercury visit;

https://brainly.com/question/19940784

#SPJ11

An automobile's horn produces a frequency of 780 Hz. How fast is the car traveling if a stationary microphone measures the horn's frequency to be 863.8 Hz? The temperature of the air is 28.8 Deg Celcius on that day.

Solution:Let's assume the speed of sound at the temperature of the air that day is v m/s.We can use the formula:υ = fλWhere:υ is the velocity of the wave (in meters per second, m/s)f is the frequency of the wave (in hertz, Hz)λ is the wavelength of the wave (in meters, m)

Let's calculate the wavelength of the sound wave using the given frequency of 780[tex]Hz:υ = fλ ⇒ λ = υ/f[/tex]The speed of sound depends on the temperature of the air, which is 28.8 deg Celsius in this case.

To find the speed of sound, we can use the following formula:v = 331 + 0.6twhere t is the temperature in degrees Celsius.

So:[tex]v = 331 + 0.6(28.8) = 348.48 m[/tex]/s Now we can substitute the values into the formula to solve for the wavelength:λ[tex]= υ/f = 348.48/780 = 0.4462 m=[/tex]

To know more about frequency visit:

https://brainly.com/question/29739263

#SPJ11

1. The phase differences between the RLC phasors are all 90 degrees. In the RLC circuit, there are three phasors, namely, the current phasor, voltage phasor across the resistor, and voltage phasor across the inductor and capacitor. The voltage phasor across the resistor leads the current phasor by 0°, and the voltage phasor across the inductor and capacitor lags the current phasor by 90°. Therefore, the voltage phasor across the capacitor is behind the current phasor by 90°.

In the RLC circuit, the phase differences between the phasors are as follows:

Voltage phasor across resistor = In-phase with the current phasor

Voltage phasor across inductor = Lags behind the current phasor by 90°

Voltage phasor across capacitor = Leads ahead of the current phasor by 90°2. The response that is characteristic of an LRC circuit driven at resonance is the current attains its maximum value. In a resonant circuit, the resonant frequency is the frequency at which the inductive reactance and the capacitive reactance are equal in magnitude, causing the impedance to be a minimum, and the current to be a maximum. The resonant frequency of a resonant circuit is calculated by the formula

f0=1/2π√(LC)

where f0 is the resonant frequency, L is the inductance, and C is the capacitance.3. RMS stands for Root Mean Square, and it is the effective or DC equivalent of an AC signal. The RMS value of a sinusoidally oscillating function is defined as the value of a direct current that produces the same heating effect in a resistor as that of an alternating current. The RMS value of a sinusoidally oscillating function is given by the formula

Vrms=Vmax/√2

where Vmax is the maximum amplitude of the sine wave signal.

Therefore, in an RLC circuit, the voltage phasor across the resistor leads the current phasor by 0°, and the voltage phasor across the inductor and capacitor lags the current phasor by 90°.

The response that is characteristic of an LRC circuit driven at resonance is the current attains its maximum value.

The RMS value of a sinusoidally oscillating function is defined as the value of a direct current that produces the same heating effect in a resistor as that of an alternating current.

To know more about phase differences, visit:

https://brainly.com/question/14594671

#SPJ11

The torque of the armature of the motor is 60 Newton-meters.

To find the torque of the armature of a motor, we can use the formula:

Torque = (Armature Current * Back EMF) / (Angular Speed * Armature Resistance)

Given:

Angular Speed (N) = 200 r/s

Armature Current = 100 Amperes

Armature Resistance = 0.5 ohms

Back EMF = 120 volts

Using the provided values, we can calculate the torque:

Torque = (100 * 120) / (200 * 0.5) = 6000 / 100 = 60 Newton-meters

Therefore, the torque of the armature of the motor is 60 Newton-meters.

Learn more about torque here:

https://brainly.com/question/30338175

#SPJ11

the cost of running the electric water heater for one month is $36.

To calculate the cost of running the electric water heater for one month, we need to determine the total energy consumption in kilowatt-hours (kWh) and then multiply it by the cost per kWh.

Given:

Power consumption = 5 kW

Duration of usage = 2 hours per day

Number of days = 30

Electricity cost = 12 cents/kWh

First, let's calculate the total energy consumption in kWh:

Energy consumption per day = Power × Time = 5 kW × 2 hours = 10 kWh

Total energy consumption for one month = Energy consumption per day × Number of days = 10 kWh/day × 30 days = 300 kWh

Now, let's calculate the cost:

Cost = Total energy consumption × Cost per kWh = 300 kWh × $0.12/kWh = $36

Therefore, the cost of running the electric water heater for one month is $36.

to know more about energy visit:

brainly.com/question/33216468

#SPJ11

(a) Carbon-14: 6 protons, 8 neutrons

(b) Cobalt-60: 27 protons, 33 neutrons

(c) Boron-11: 5 protons, 6 neutrons

(d) Tin-120: 50 protons, 70 neutrons

(a) Carbon-14:

The isotope carbon-14 has a mass number of 14, which indicates the total number of protons and neutrons in its nucleus. Carbon has an atomic number of 6, which represents the number of protons. To determine the number of neutrons, we subtract the atomic number from the mass number.

Number of protons: 6

Number of neutrons: 14 - 6 = 8

Therefore, carbon-14 has 6 protons and 8 neutrons.

(b) Cobalt-60:

The isotope cobalt-60 has a mass number of 60.

Number of protons: The atomic number of cobalt is 27, so it has 27 protons.

Number of neutrons: To find the number of neutrons, we subtract the atomic number from the mass number.

Number of neutrons: 60 - 27 = 33

Therefore, cobalt-60 has 27 protons and 33 neutrons.

(c) Boron-11:

The isotope boron-11 has a mass number of 11.

Number of protons: The atomic number of boron is 5, so it has 5 protons.

Number of neutrons: To find the number of neutrons, we subtract the atomic number from the mass number.

Number of neutrons: 11 - 5 = 6

Therefore, boron-11 has 5 protons and 6 neutrons.

(d) Tin-120:

The isotope tin-120 has a mass number of 120.

Number of protons: The atomic number of tin is 50, so it has 50 protons.

Number of neutrons: To find the number of neutrons, we subtract the atomic number from the mass number.

Number of neutrons: 120 - 50 = 70

Therefore, tin-120 has 50 protons and 70 neutrons.

Learn more about protons

brainly.com/question/12535409

#SPJ11

We know that the magnetic force on a charged particle moving with velocity v in a magnetic field of strength B is given by the equation: F = qvBsinθ, Where q is the charge of the particle, v is the velocity of the particle, B is the magnetic field strength and θ is the angle between v and B.

Given, the electric charge of alpha particle = 2e = 2 × 1.6 × [tex]10^{-19}[/tex] C

The mass of alpha particle = 4 u = 4 × 1.661 × [tex]10^{-27[/tex] kg

Radius of the circular path, r = 5.47 cm = 5.47 × [tex]10^{-2[/tex] m

Magnetic field, B = 1.77 T

(a) Speed of the alpha particle

We know that the magnetic force on a charged particle moving with velocity v in a magnetic field of strength B is given by the equation: F = qvBsinθ

Where q is the charge of the particle, v is the velocity of the particle, B is the magnetic field strength and θ is the angle between v and B. Since the alpha particle moves in a circular path, the magnetic force F acts as the centripetal force [tex]mv^2[/tex]/r. Therefore, we have:

[tex]mv^2[/tex]/r = qvBsinθ

We know that the angle between the velocity of the alpha particle and the magnetic field is 90°.

sinθ = 1

Substituting the given values in the above equation, we get: [tex]mv^2[/tex]/r = qv

B⇒ v = q

Br/m= 2 × 1.6 × [tex]10^{-19[/tex] C × 1.77 T × 5.47 × [tex]10^{-2[/tex] m / 4 × 1.661 × [tex]10^{-27[/tex] kg= 4665975.9 m/s

Therefore, the speed of the alpha particle is 4.67 × [tex]10^6[/tex] m/s.

(b) Period of revolution

The time taken by the alpha particle to complete one revolution is called its period of revolution T. We can calculate T using the formula: T = 2πr/v= 2π × 5.47 × [tex]10^{-2[/tex] m / 4.67 × [tex]10^6[/tex] m/s= 7.3658 ×[tex]10^{-8[/tex]s

Therefore, the period of revolution of the alpha particle is 7.37 × [tex]10^{-8[/tex] s.

(c) Kinetic energy

The kinetic energy of the alpha particle is given by the formula: K.E. = 1/2 [tex]mv^2[/tex]= 1/2 × 4 × 1.661 × [tex]10^{-27[/tex] kg × (4.67 × [tex]10^6[/tex] m/s[tex])^2[/tex]= 7.2280 × [tex]10^{-20[/tex] J= 7.2280 × [tex]10^{-20[/tex] J × 6.24 × [tex]10^{18[/tex] eV/J= 4.50 eV

Therefore, the kinetic energy of the alpha particle is 4.50 eV.

(d) Potential difference

To find the potential difference, we can use the formula: K.E. = eV

where K.E. is the kinetic energy of the alpha particle and e is the charge of an electron. Substituting the given values, we get: 4.50 eV = 1.6 × [tex]10^{-19[/tex] C × V⇒ V = 4.50 eV / 1.6 ×[tex]10^{-19[/tex] C= 2.34 × [tex]10^5[/tex] V

Therefore, the potential difference through which the alpha particle would have to be accelerated to achieve this energy is 2.34 × [tex]10^5[/tex] V.

To know more about magnetic field visit:

https://brainly.com/question/19542022

#SPJ11

i) The equivalent circuit:  L is 1.2 × 10-3 H

ii) Peak current: Ip is 34 A

iii) Peak voltage is 15 V

i) The equivalent circuit:

At the point of strike, the equivalent circuit can be determined as follows:

Equivalent circuit

R = 1500 // 600

= 429.7 Ω

C = 1.21/1500

= 8.0 × 10-7 F

(rounded to two significant figures)

L = 1500 × 8 × 10-7

= 1.2 × 10-3 H

(rounded to two significant figures)

ii) Peak current: The peak current is determined by

Ip = Vp/R.

To determine the peak current, first, we need to determine the peak voltage. The peak voltage can be determined as follows:

Vp = Zc × Ic

= 1500 × 10 × 10-3

= 15 V

Therefore, the peak current is given by'

Ip = Vp/R

= 15/429.7

= 0.034 A

≈ 34 A (rounded to two significant figures).

iii) Peak voltage: The peak voltage has already been determined as 15 V (in part ii) above).

To know more about Peak current visit:

https://brainly.com/question/31870573

#SPJ11