Quickly dissolving a solute in a solvent, you can increase the temperature and/or agitate the mixture.
The ability of a solute to dissolve in a solvent is described by its solubility.
The type of solute that dissolves the fastest is typically one that has a high solubility in the solvent and is finely divided or has a large surface area.
The three ways to dissolve a solute in a solvent are increasing temperature, agitating the mixture, and using solubility-enhancing agents.
Dissolving a solute in a solvent can be facilitated by employing various techniques. One way to expedite the dissolution process is by increasing the temperature of the solvent.
Higher temperatures provide more energy to the solvent molecules, allowing them to move more vigorously and collide with the solute particles more frequently.
This enhanced kinetic energy helps overcome the intermolecular forces holding the solute particles together, promoting their separation and dissolution into the solvent.
Agitating the mixture is another effective method. Stirring or shaking the solution helps to increase the contact between the solute and solvent, increasing the chances of successful collisions and facilitating faster dissolution.
The ability of a solute to dissolve in a solvent is described by its solubility.
Solubility refers to the maximum amount of solute that can dissolve in a given quantity of solvent at a specific temperature and pressure.
It is influenced by factors such as the nature of the solute and solvent, their respective polarities, and the presence of any solubility-enhancing agents.
Solutes with high solubility in a particular solvent will dissolve more readily compared to those with low solubility.
The type of solute that dissolves the fastest is typically one that possesses high solubility in the solvent and is either finely divided or has a large surface area.
A solute with high solubility readily interacts with the solvent molecules, leading to rapid dissolution.
Finely divided solutes or those with a large surface area provide more contact points for the solvent molecules, allowing for more efficient dissolution.
In summary, to quickly dissolve a solute in a solvent, increasing the temperature and agitating the mixture are effective techniques.
Solubility determines the ability of a solute to dissolve in a solvent, while a solute with high solubility, fine division, or a large surface area generally dissolves most rapidly.
Dissolution is a complex process influenced by multiple factors, including temperature, solute-solvent interaction, solubility, and surface area.
Understanding these factors and their interplay can provide insights into optimizing dissolution processes for specific applications.
Learn more about Dissolving a solute
brainly.com/question/8586615
#SPJ11
The boiling point of ethanol {CH}_{3} {CH}_{2} {OH} is 78.50^{\circ} {C} at 1 atmosphere. A nonvolatile, nonelectrolyte that dissolves in ethanol is saccharin.
Saccharin is a non-volatile and non-electrolyte substance. It is soluble in ethanol. The boiling point of ethanol is 78.50℃ at 1 atmosphere.
The dissolution of saccharin in ethanol does not affect the boiling point of the solution. The boiling point of ethanol is a physical property that refers to the temperature at which ethanol will change from a liquid to a gas phase. The boiling point of ethanol is 78.50℃ at 1 atmosphere pressure. This is an important factor to consider when using ethanol for various purposes, as it affects its performance and characteristics.
Saccharin, on the other hand, is a non-volatile and non-electrolyte substance. It is a synthetic compound that is widely used as an artificial sweetener in food and beverage products. When saccharin is dissolved in ethanol, it does not affect the boiling point of the solution because saccharin is non-volatile. Therefore, the boiling point of the solution remains at 78.50℃ at 1 atmosphere pressure.
To know more about non-electrolyte visit:
brainly.com/question/14566383
#SPJ11
Determine whether the study is experiment or an observational study, and then identify a major problem with the study. a) The Physicians Health Study involved 22,071 male physicians. Based on random selections, 11,037 of them were treated with aspirin and the other 11,034 were given placebos. The study was stopped early because it became clear that the aspirin reduced the risk of hear attack by a substantial amount. b) A medical researcher tested for a difference in systolic blood pressure levels between male and female students who are 12 years of age. She randomly selected four males and four females for her study.
a) The study is an experimental study.
A major problem with the study is the lack of blinding.
b) The study is an observational study.
A major problem with the study is the small sample size.
a) The Physicians Health Study is an experiment because the researchers intentionally assigned participants to two groups: one receiving aspirin and the other receiving placebos.
A major problem with the study is the lack of blinding. Since the participants were aware of whether they were receiving aspirin or placebos, their knowledge could have influenced their behavior and responses, potentially introducing bias. Additionally, the study involved only male physicians, so the results may not be generalizable to other populations or genders.
b) The study described is an observational study because the researcher did not intervene or assign treatments. Instead, the researcher observed and compared existing differences in systolic blood pressure levels between male and female students.
A major problem with the study is the small sample size. With only four males and four females, the sample may not be representative of the larger population, limiting the generalizability of the findings. Additionally, the study did not specify any control or comparison group, making it challenging to draw definitive conclusions about the differences in blood pressure between genders.
Learn more about experimental study
https://brainly.com/question/3233616
#SPJ11
If 0.889J of heat causes a 0.124 degree C temperature change, what mass of water is present?
Answer:
m = 1.73 g
Explanation:
We can use the formula for heat capacity to solve this problem:
q = m x c x ΔT
where q is the heat energy transferred, m is the mass of the substance, c is the specific heat capacity of the substance, and ΔT is the change in temperature.
In this case, we know that q = 0.889 J and ΔT = 0.124°C. We are trying to find the mass of water present.
The specific heat capacity of water is 4.184 J/g°C. Substituting the given values into the formula, we get:
0.889 J = m x 4.184 J/g°C x 0.124°C
Simplifying and solving for mass, we get:
m = 0.889 J / (4.184 J/g°C x 0.124°C)
m = 1.73 g
The mass of water that would be present when 0.889J of heat causes 0.124°C temperature change is 1.712 g.
We know from the following formula,
Q=m x c x ΔT
where, Q ⇒Amount of heat energy (absorbed or liberated)
m ⇒mass of the sample
c ⇒specific heat capacity of the sample
ΔT ⇒Change in temperature
So, putting in the formula,
Q=0.889J (given)
ΔT=0.124°C (given)
c=4.186 J/ g-°C (specific heat capacity of water)
∴ Q= mcΔT
⇒ 0.889= mx(4.186)x(0.124)
⇒ m= 1.712 g
Specific heat capacity is the measure of what amount of energy is needed to be added to something to make it 1 degree hotter.
To learn more about Heat and Specific heat concepts:
https://brainly.com/question/27991746
which molecule has a central atom that is sp3 hybridized? select the correct answer below: sf6 ch3cl alcl3 pcl5
The molecule that has a central atom that is sp3 hybridized is CH3Cl. To determine the hybridization of an atom, we need to count the number of electron groups around the central atom.
In this case, the central atom in CH3Cl is carbon (C). CH3Cl has four electron groups around the central carbon atom: three sigma bonds with hydrogen (C-H bonds) and one sigma bond with chlorine (C-Cl bond). Each sigma bond counts as one electron group.
The four electron groups indicate that the carbon atom is sp3 hybridized. In sp3 hybridization, the carbon atom forms four sigma bonds with four electron groups, resulting in a tetrahedral geometry. Therefore, the correct answer is CH3Cl.
More on sp3 hybridized: https://brainly.com/question/8235897
#SPJ11
The Lewis structure for HN3 is given below. N=N=N-H The formal charge on the nitrogen atom second from left (marked with an a)is: O +1 +2 -1 -2
To determine the formal charge on the nitrogen atom marked with "a" in the Lewis structure of HN₃ (N=N=N-H), we need to compare the number of valence electrons on the atom with its assigned electrons in the structure.
In the Lewis structure given (N=N=N-H), the nitrogen atom marked with "a" is bonded to three other atoms (two nitrogen atoms and one hydrogen atom) and has one lone pair of electrons.
The nitrogen atom (N) has five valence electrons. In the structure, it is bonded to three atoms (two nitrogen and one hydrogen) and has one lone pair. Each bond contributes one electron, and the lone pair is assigned two electrons.
To calculate the formal charge, we use the formula:
Formal Charge = Valence Electrons - Assigned Electrons
For the nitrogen atom marked with "a":
Valence Electrons = 5
Assigned Electrons = 3 (from the bonds) + 2 (from the lone pair)
Assigned Electrons = 5
Formal Charge = 5 - 5 = 0
Therefore, the formal charge on the nitrogen atom marked with "a" is 0.
Learn more about formal charges here:
https://brainly.com/question/33737884
#SPJ 4
1. The formula for the conjugate acid of NO3- is _____
2. The formula for the conjugate base of NH4+ is _____
The formula for the conjugate acid of [tex]\rm NO_3^-[/tex] is [tex]\rm HNO_3[/tex] and the formula for the conjugate base of [tex]\rm NH_4^+[/tex] is [tex]\rm NH_3[/tex] respectively.
A conjugate acid contains one more H atom and one more + charge than the base that formed it. Conjugate acid is formed when an acid donates a proton to a base.
When a Brønsted-Lowry base accepts a proton, it becomes its conjugate acid. Similarly, when a Brønsted-Lowry acid donates a proton, it becomes its conjugate base.
1. The formula for the conjugate acid of [tex]\rm NO_3^-[/tex] is [tex]\rm HNO_3[/tex]. [tex]\rm NO_3^-[/tex]is a polyatomic anion that has a charge of -1. When it accepts a proton (H+), it forms [tex]\rm HNO_3[/tex], which is nitric acid.
2. The formula for the conjugate base of [tex]\rm NH_4^+[/tex] is [tex]\rm NH_3[/tex]. [tex]\rm NH_4^+[/tex] is a polyatomic cation that has a charge of +1. When it donates a proton (H+), it forms [tex]\rm NH_3[/tex], which is ammonia.
Therefore, conjugate acid of [tex]\rm NO_3^-[/tex] is [tex]\rm HNO_3[/tex] and conjugate base of [tex]\rm NH_4^+[/tex] is [tex]\rm NH_3[/tex] , respectively.
Learn more about conjugate acid here:
https://brainly.com/question/29870371
#SPJ4
what is the final concentration of h2so4 when 8.65 ml of 18.1 m h2so4 is diluted to a final volume of 100. ml?
The final concentration of H₂SO₄ after dilution is 1.564 M.
Concentration refers to the amount of a substance present in a given volume or mass of a solution or mixture. It is a measure of how much solute is dissolved or dispersed in a solvent or mixture.
Concentration can be expressed in various ways, such as molarity (moles of solute per liter of solution), mass/volume percent (mass of solute per volume of solution), or parts per million (ppm).
C₁V₁ = C₂V₂
Where:
C₁ = Initial concentration of H₂SO₄
V₁ = Initial volume of H₂SO₄
C₂ = Final concentration of H₂SO₄
V₂ = Final volume of the solution
Given:
C₁ = 18.1 M
V₁ = 8.65 mL
V₂ = 100 mL
C₂ = (C₁ × V₁) / V₂
C₂ = (18.1 M × 8.65 mL) / 100 mL
C₂ = 1.564 M
Learn more about Concentration, here:
https://brainly.com/question/30862855
#SPJ4
Cyclohexane and toluene have boiling points of 80.8∘ C and 110.6∘C, respectively. If distilling a mixture of these two compounds, which will distill first? Toluene Cyclohexane Question 8 1 pts According to the SDS, which of the following is a possible hazard for isopropanol? Radioactive Flammable Corrosive Oxidizer What must be done when assembling the distillation apparatus to prevent the loss of vapor? Apply acetone to all of the joints. Rub all the joints with alcohol. Soak all the pieces of glassware in water for 45 minutes. Apply vacuum grease to all of the joints. Question 10 1 pts In a simple distillation setup, what is the sequence of equipment from the bench top to the round bottom flask? Heating mantle, stir plate, lab jack Lab jack, stir plate, heating mantle Heating mantle only Stir plate, lab jack, heating mantle
Cyclohexane and toluene have boiling points of 80.8∘C and 110.6∘C, respectively. While distilling a mixture of these two compounds, the first to distill will be cyclohexane. This is because cyclohexane has a lower boiling point than toluene and hence it will be the first one to evaporate.
The boiling point of any substance is related to the strength of the attractive forces between the molecules of that substance. The stronger the intermolecular forces, the higher will be the boiling point and vice versa.
The boiling point of toluene is higher than that of cyclohexane because toluene has stronger attractive forces due to the presence of the -CH3 group which induces dipole-dipole interactions and hence stronger intermolecular forces.
According to the SDS, flammable is a possible hazard for isopropanol. Isopropanol (isopropyl alcohol) is a clear, colorless, and volatile liquid that is flammable and highly flammable. It is widely used in industry and medicine as a solvent, disinfectant, and antifreeze.
When assembling the distillation apparatus, vacuum grease must be applied to all of the joints. The main reason for applying vacuum grease is to provide a tight seal around the joints of the apparatus and to prevent the loss of vapor.
It is important to prevent the loss of vapor because it can lead to the loss of the desired product and can also be a safety hazard. Applying vacuum grease ensures that the apparatus is airtight and the vapor produced is collected in the collection flask.
In a simple distillation setup, the sequence of equipment from the benchtop to the round-bottom flask is as follows: Heating mantle, lab jack, round-bottom flask.
The heating mantle is used to heat the sample and the lab jack is used to adjust the height of the round-bottom flask. The round-bottom flask is where the sample is collected after it has been distilled.
The stir plate is not used in a simple distillation setup because the sample is not being stirred. Simple distillation is used to separate two liquids that have a large difference in boiling points (more than 25°C) and do not have any other chemical properties in common.
To know more about cyclohexane here
https://brainly.com/question/17019157
#SPJ11
Name the dependent and independent variables for each
procedure?
What must be included in the title of a graph?
What is a curve in graphs?
The dependent variable is the measured or observed variable, while the independent variable is the manipulated or controlled variable in scientific experiments.
In scientific experiments, the dependent variable is the variable being measured or observed, while the independent variable is the variable being manipulated or controlled.
For each procedure, the dependent and independent variables can vary depending on the specific experiment. Here are some examples:
Procedure 1
Dependent variable: Temperature
Independent variable: Time
Procedure 2
Dependent variable: Height
Independent variable: Amount of fertilizer
Procedure 3
Dependent variable: Reaction rate
Independent variable: Concentration of reactant
In the title of a graph, it is important to include the variables being plotted and the units of measurement.
This helps to clearly describe the content of the graph and provide information to the reader. For example, a title could be "Temperature (°C) vs. Time (min)" or "Height (cm) vs. Amount of Fertilizer (g)."
In graphs, a curve refers to the line or shape created when plotting data points on a graph. It represents the relationship or trend between the independent and dependent variables.
The curve can be smooth or jagged, depending on the nature of the data. The shape of the curve provides insights into the relationship between the variables and helps in analyzing the data.
To know more about dependent variable refer here
https://brainly.com/question/33270051#
#SPJ11
Select the true statement. The four most prevalent elements in biosystems, in random order, are. H.O.S.C. The chiral amino acids found in biosystems are D-stereoisomers. Hydrogen bonds are weaker in non-polar solvents than they are in water. The strength of ionic bonds is inversely proportional to the dielectric constant of the solvent.
The correct statement is "Hydrogen bonds are weaker in non-polar solvents than they are in water."
The four most prevalent elements in biosystems, in random order, are C, H, O, and N. Amino acids are the building blocks of proteins, and the majority of the ones found in nature are L-stereoisomers, which means that they are left-handed. Ionic bonds are stronger in low dielectric constant solvents than in high dielectric constant solvents. They're also weaker in water because of its high dielectric constant. As a result, hydrogen bonding is stronger in water than in nonpolar solvents.
Therefore, the statement, "Hydrogen bonds are weaker in non-polar solvents than they are in water" is true.
Learn more about Ionic bonds-
brainly.com/question/977324
SPJ11
The rate of a chemical reaction increases if the frequency of molecular collisions within the system increases. a)TRUE b)FALSE
The given statement that "The rate of a chemical reaction increases if the frequency of molecular collisions within the system increases" is TRUE.
The chemical reaction rate increases if the frequency of molecular collisions within the system increases. The collision theory helps to understand how different factors affect the reaction rate. This theory states that chemical reactions occur when molecules collide with each other.
The rate of a chemical reaction depends on the frequency of the collisions, the energy transferred during the collisions, and the orientation of the molecules during the collision.
Therefore, the rate of a chemical reaction increases if the frequency of molecular collisions within the system increases. So, the statement given in the question is true.
Learn more about reaction rate from the given link:
https://brainly.com/question/28566775
#SPJ11
Consider a one-dimensional NaCl crystal where each ion has nearest neighbours of the opposite charge a distance ' a ' from it. One of the Na +
ions is displaced by a small amount δ(a>>δ) from its equilibrium position. Obtain an expression for the change in the Madelung constant to the smallest non-vanishing order in δ. What can you conclude from the result.
The change in the Madelung constant is proportional to the displacement, and it is dependent on the charge of the ions, the distance between the displaced ion and its nearby ions, and other factors, according to this conclusion.
Let's investigate the electrostatic potential caused by the displacement of the Na⁺ ion in order to generate an expression for the change in the Madelung constant to the smallest non-vanishing order in.
The total electrostatic potentials contributed by each ion in the crystal lattice are represented by the Madelung constant. The change in the electrostatic potential brought on by the slight movement of one Na⁺ ion will have an impact on how the Madelung constant changes.
We can think about the change in the Madelung constant up to the first-order approximation if the displacement is small (a >> ). Let M stand for the Madelung constant's initial value and M for its variation.
We can analyze the change by taking into account the Madelung constant's contribution from the displaced Na⁺ ion. Since every ion has close neighbors with the opposite charge, the displaced ion's electrostatic potential will be impacted by the nearby ions.
By taking into account the contribution from the nearby ions and applying Coulomb's equation, we may roughly determine the potential at the location of the displaced ion. Let r be the distance between the displaced ion and its nearby ions (a in the equilibrium constant), and let q be the charge of the ions, which is the elementary charge e.
When the displacement is taken into account, the electrostatic potential change can be roughly calculated as V q / (40r), where 0 is the vacuum permittivity.
We can now think about how this hypothetical change affects the Madelung constant. The total electrostatic potential of all the ions affects the Madelung constant. We can write the change as M N V because that is what we are interested in, where N is the total number of ions in the crystal lattice.
When the expression for V is substituted, we get M N (q / (40r)).
The formula for the Madelung constant change to the smallest non-vanishing order in is as follows:
ΔM ≈ N (q / (4πε₀r)) δ.
The change in the Madelung constant is proportional to the displacement, and it is dependent on the charge of the ions, the distance between the displaced ion and its nearby ions, and other factors, according to this conclusion.
To know more about equilibrium constant:
https://brainly.com/question/32542562
#SPJ4
How many Ba2+ ions are contained in 5.46 g of BaCrO4?
BaCrO4 is a chemical compound with a molar mass of 253.32 g/mol. BaCrO4 contains Ba2+ ions, which are ionic forms of barium. Barium chromate is the common name for BaCrO4.
This chemical compound is made up of one barium ion (Ba2+) and one chromate ion (CrO42−).
To determine how many Ba2+ ions are contained in 5.46 g of BaCrO4, we need to use the molar mass and the formula weight of the Ba2+ ion.
Ba2+ has a molar mass of 137.33 g/mol, which we can use to convert from mass to moles.
To get the number of Ba2+ ions in the sample,
we need to divide the number of moles of BaCrO4 by the number of moles of Ba2+.5.46 g BaCrO4 x (1 mol BaCrO4 / 253.32 g BaCrO4) x (1 mol Ba2+ / 1 mol BaCrO4) = 0.0215 mol Ba2+
To determine the number of Ba2+ ions, we must multiply the number of moles of Ba2+ by Avogadro's number.
1 mol Ba2+ x (6.022 x 1023 Ba2+ ions / 1 mol Ba2+) = 1.30 x 1022 Ba2+ ions
There are 1.30 x 1022 Ba2+ ions in 5.46 g of BaCrO4.
To know more about chemical compound visit:
https://brainly.com/question/33413143
#SPJ11
What is the electron-domain (charge-cloud) geometry of BrF5? Enter the electron-domain geometry of the molecule.
b. What is the molecular geometry of BrF5?
c. Ignoring lone-pair effects, what is the smallest bond angle in BrF5?
d. Which choice best describes the polarity of BrF5?
The electron-domain (charge-cloud) geometry of BrF5 is octahedral, and the molecular geometry is square pyramidal.
In BrF5, bromine (Br) is the central atom surrounded by five fluorine (F) atoms. The Br atom has seven valence electrons, and each F atom contributes one valence electron. The total number of valence electrons is 34. Based on the electron-domain geometry, there are six electron domains around the central Br atom, consisting of five bonding pairs (Br-F) and one lone pair.
The electron-domain geometry of BrF5 is octahedral because it has six electron domains. This arrangement maximizes the distance between electron domains, resulting in a symmetrical structure. However, considering the molecular geometry, the lone pair occupies more space than the bonding pairs, causing the fluorine atoms to be slightly pushed downward. This leads to a square pyramidal molecular geometry.
Ignoring lone-pair effects, the smallest bond angle in BrF5 is approximately 90 degrees. This angle occurs between the two adjacent fluorine atoms in the axial positions of the square pyramid.
Regarding the polarity of BrF5, the molecule is polar due to the asymmetrical arrangement caused by the lone pair. The fluorine atoms are highly electronegative, causing an uneven distribution of electron density. As a result, BrF5 exhibits a net dipole moment, making it a polar molecule.
Learn more about electron-domain
brainly.com/question/30461548
#SPJ11
convert 8.654 X 10^11 nm/sec to cm/hour
The given quantity is 8.654 × 10^11 nm/sec. Convert this quantity to cm/hour.
Here,8.654 × 10^11 nm/sec = 8.654 × 10^11 × (1/10^9) m/sec= 865.4 m/sec
Now, we have to convert this quantity into cm/hour.1 km = 1000 m and 1 hour = 3600 sec ⇒ 1 km/hour = 1000 m/3600 sec⇒ 1 km/hour = 5/18 m/sec.So,865.4 m/sec = (865.4 × 5/18) km/hour= (2403.889) km/hour= 2.403889 × 10^3 km/hour.
We have to convert km/hour to cm/hour as,1 km = 10^5 cm
Therefore,1 km/hour = (10^5) / 3600 cm/sec= (1000/36) cm/sec.So,2.403889 × 10^3 km/hour = (2.403889 × 10^3) × (1000/36) cm/hour= (66.77469444 × 10^3) cm/hour= 6.677 × 10^4 cm/hour.
Thus, 8.654 × 10^11 nm/sec is equivalent to 6.677 × 10^4 cm/hour.
to know more about hour here:
brainly.com/question/13349617
#SPJ11
A given ample of ga ha a volume of 4. 20 L at 60. C and 1. 00 atm preure. Calculate it preure if the volume i changed to 5. 00 L and the temperature to 27C (aume the amount of ga doe not change)
The pressure of the gas would be 0.84 atm when the volume is changed to 5.00 L and the temperature is changed to 27°C.
To calculate the pressure of a gas when the volume and temperature are changed, we can use the ideal gas law equation: PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the gas constant, and T is the temperature in Kelvin.
Initial volume (V₁) = 4.20 L
Initial temperature (T₁) = 60°C = 333 K
Initial pressure (P₁) = 1.00 atm
Final volume (V₂) = 5.00 L
Final temperature (T₂) = 27°C = 300 K
To solve for the final pressure (P₂), we can use the equation PV = nRT and compare the initial and final states of the gas.
1: Convert temperatures to Kelvin
Initial temperature (T₁) = 60°C = 333 K
Final temperature (T₂) = 27°C = 300 K
2: Use the equation PV = nRT to compare the initial and final states of the gas.
(P₁)(V₁) = (P₂)(V₂)
3: Rearrange the equation to solve for P₂.
P₂ = (P₁)(V₁) / V₂
4: Substitute the given values into the equation.
P₂ = (1.00 atm)(4.20 L) / 5.00 L
5: Calculate the final pressure (P₂).
P₂ = 0.84 atm
You can learn more about pressure at: brainly.com/question/32099691
#SPJ11
pls
help me
1.) What is the chemical reaction equation for 1-propanol? 2.) What is the chemical reaction equation for 2-propanol?
The chemical reaction equation for 1-propanol is : CH₃CH₂CH₂OH + 6[O] → 3CO₂ + 4H₂O₂.)
The chemical reaction equation for 2-propanol is : CH₃CHOHCH₃ + 3[O] → 2CO₂ + 3H₂O
1-propanol is also known as n-propanol, 1-propyl alcohol, or propan-1-ol. The chemical formula of 1-propanol is CH₃CH₂CH₂OH. 1-Propanol is used as a solvent, in the manufacturing of various chemicals, and in the production of cosmetics and pharmaceuticals.1-propanol is highly flammable and can react with oxidizing agents, such as potassium permanganate or chromic acid, to produce heat and potentially explosive mixtures.1-propanol is oxidized when it reacts with oxygen, producing carbon dioxide and water. The balanced equation for this reaction is:
CH₃CH₂CH₂OH + 6[O] → 3CO₂ + 4H₂O
The equation for 2-propanol is as follows:
CH₃CHOHCH₃ + 3[O] → 2CO₂ + 3H₂O
The chemical formula of 2-propanol is CH₃CHOHCH₃. 2-propanol is used as a solvent and a cleaning agent. 2-propanol is flammable and should be handled with care when used in an industrial setting.2-propanol is oxidized when it reacts with oxygen, producing carbon dioxide and water. The balanced equation for this reaction is:
CH₃CHOHCH₃ + 3[O] → 2CO₂ + 3H₂O
Learn more about 1-propanol at https://brainly.com/question/30909638
#SPJ11
