which of the following conditions does not contribute to greater gas ideality? group of answer choices lower system temperatures larger system volumes smaller gas molecule sizes smaller system pressures

Answer: 20.16cm³ of CO₂ produced

Explanation: the equation for the reaction between carbon monoxide (CO) and oxygen (O2) is:

2CO (g) + O₂ (g) → 2CO₂ (g)

Given that 20 cm³ of carbon monoxide is reacted with 10 cm³ of oxygen. From the equation,

we can see that two molecules of CO react with one molecule of O₂to produce two molecules of CO₂

Since we have 20 cm³ of CO and 10 cm³ of O₂, we can calculate the number of moles of CO and O₂ as follows:

CO: 20 cm³ x (1 mole / 22.4 cm³) = 0.89 moles

O₂: 10 cm³ x (1 mole / 22.4 cm³) = 0.45 moles

Since two molecules of CO react with one molecule of O₂, the number of moles of O₂ is half the number of moles of CO. Since we have 0.45 moles of O₂, we can calculate the number of moles of CO₂ produced as follows:

0.45 moles x 2 = 0.9 moles

Finally, to find the volume of CO₂ produced, we can multiply the number of moles of CO₂ by the volume occupied by one mole of CO₂:

0.9 moles x 22.4 cm³/mole = 20.16 cm³

Read more about stoichiometry and mole concept:

https://chem.libretexts.org/Bookshelves/Introductory_Chemistry/Beginning_Chemistry_(Ball)/05%3A_Stoichiometry_and_the_Mole#:~:text=5.2%3A%20Stoichiometry,mass%20in%20atomic%20mass%20units.

Standard deviation is a quantity which describes how spread out a set of data is.

A standard deviation (or σ) is a measure of how dispersed the data is in relation to the mean. Low standard deviation means data are clustered around the mean, and high standard deviation indicates data are more spread out.

A standard deviation close to zero indicates that data points are close to the mean, whereas a high or low standard deviation indicates data points are respectively above or below the mean. Standard deviation is a statistic that measures the dispersion of a dataset relative to its mean and is calculated as the square root of the variance.

Learn more about standard deviation,here:

https://brainly.com/question/16555520

#SPJ1

A standard EpiPen contains approximately 0.3 milligrams of epinephrine, which is equivalent to 0.3 milliliters of a 1:1000 solution, or 3 micrograms of epinephrine per dose. there are approximately 9.83 x 10^20 molecules of epinephrine in a standard EpiPen.

Epinephrine, also known as adrenaline, is a hormone and neurotransmitter that is produced naturally by the body in response to stress or danger. It acts on the sympathetic nervous system to increase heart rate, constrict blood vessels, dilate airways, and mobilize energy stores in the body. It is also used as a medication to treat severe allergic reactions, such as anaphylaxis.

A standard EpiPen is a self-administered device that contains a single dose of epinephrine in a prefilled syringe. The EpiPen delivers the medication through a spring-loaded mechanism that injects the solution into the thigh muscle. The dose is typically 0.3 milligrams (or 0.3 milliliters) of a 1:1000 solution of epinephrine, which means that there is 1 milligram of epinephrine in 1000 milliliters of solution.

To calculate the number of molecules of epinephrine in a standard EpiPen, we need to know the molecular weight of epinephrine and Avogadro's number, which is the number of molecules in one mole of a substance. The molecular weight of epinephrine is approximately 183 grams per mole, which means that one mole of epinephrine contains Avogadro's number (6.02 x 10^23) molecules.

Since the dose of epinephrine in a standard EpiPen is 0.3 milligrams, we can convert this to micrograms by multiplying by 1000, which gives us 300 micrograms. To calculate the number of molecules of epinephrine in 300 micrograms, we need to use the formula:

Number of molecules = (mass in micrograms/molecular weight) x Avogadro's number

Plugging in the values for epinephrine, we get:

Number of molecules = (300/183) x 6.02 x 10^23

Simplifying this expression gives us:

Number of molecules = 9.83 x 10^20

Therefore, there are approximately 9.83 x 10^20 molecules of epinephrine in a standard EpiPen.

Learn more about EPIPEN here:

https://brainly.com/question/28097758

#SPJ4

In most cases, the formal element that contributes most to the viewer's awareness of the passage of time is the use of duration.

This can be achieved through various means, such as the duration of shots or scenes, the pacing of events, or the progression of the plot. For example, in a film or video, longer shots or scenes can create a sense of leisurely passing time, while quicker cuts or montages can convey a sense of accelerated time. In a musical composition, changes in tempo and rhythm can also contribute to the perception of time passing.Other formal elements, such as lighting and sound design, can also play a role in shaping the viewer's perception of time, but the most direct and significant influence is typically the use of duration.

Learn more about film here:

https://brainly.com/question/14824318

#SPJ4

Volume is the amount of space taken up by an object

The instrument used to measure liquid volume is called a graduated cylinder.

The formula used to calculate the volume of a solid object such as a rectangular prism is: V =  length, *  width * height

Volume is a measure of the amount of space that a substance or object occupies. It is typically measured in units such as liters, cubic meters, gallons, or cubic feet.

The instrument used to measure liquid volume is called a graduated cylinder. It is a cylindrical tube made of glass or plastic, with volume markings along its length that allow for the accurate measurement of liquids.

The formula used to calculate the volume of a solid object depends on its shape. Here are some common formulas for finding the volume of different types of solid objects:

Cube: V = s³ (where s is the length of one side of the cube)

Rectangular prism: V =  length, *  width * height

Sphere: V = 4/3πr³ (where r is the radius of the sphere)

Cylinder: V = πr^2h (where r is the radius of the cylinder and h is its height)

Learn more about the volume of a substance at: https://brainly.com/question/27710307

#SPJ1

In water, a substance that is ionizes totally and completely in solution is called strong electrolyte.

Ionization is a process in which a neutral snippet or patch earnings or loses one or further electrons. The performing charged snippet/ patch is called an ion. A appreciatively charged ion is called a cation, while a negatively charged ion is called an anion.

The ionization process is used in a wide variety of outfit, for illustration, spectrometer, radiation remedy, fluorescent lights,etc.

Strong electrolytes are ones that completely ionise or dissociate in their aqueous solution.

These electrolytes have a higher extension of ionisation and a high electrical conductivity.

Learn more about Strong electrolyte:

https://brainly.com/question/2285692

#SPJ4

The volume of hydrogen at STP is required to produce 25 g of ammonia is 37.5 g.

The balanced equation for the formation of ammonia is given as follows

N₂ + 3H₂ → 2NH₃

The stoichiometry of H₂ to NH₃ is 3 : 2.

Avagadros law states that "at volume of gas is proportional to number of moles of gas at constant pressure and temperature."

Therefore, the molar ratio is equivalent to volume ratio,

Hence, the volume ratio of H₂ to NH₃ is 3 : 2

It can be concluded that 2 L of NH₃ requires 3 L of H₂.

Then 25.g of NH₃ requires = 3/2 x 25 = 37.5 g of H₂

So, volume of H₂ required is 37.5 g.

Learn more about volume from the link given below.

https://brainly.com/question/27868083

#SPJ4

The water features are often associated with the condensation is the correct option are The Ocean and the Clouds and Dew.

The Condensation is the process where the water vapor will becomes the liquid. The condensation is the reverse of the evaporation, in which the liquid water becomes the water vapor. The Condensation is occurs one of the two ways: the first way is the air is cooled to the dew point and  it will becomes so saturated with the water vapor  and it cannot be hold  more of the water.

Thus, The Ocean and the Clouds and Dew is the feature of water that is connected with the condensation.

To learn more about condensation here

https://brainly.com/question/868510

#SPJ4

The final equilibrium temperature is approximately 247.7°C and the percentage of ice that melts is 50%.

The amount of heat transferred is given by the equation:

[tex]Q = m * c * \triangle T[/tex]

First, we need to calculate the amount of heat needed to melt the ice. The heat required to melt ice is given by the equation:

[tex]Q = m * L[/tex]

where L is the latent heat of fusion of ice, which is 334 J/g. Therefore, the heat required to melt 50 g of ice is:

[tex]Q = 50 g * 334 J/g = 16700 J[/tex]

the heat lost by the water is equal to the heat gained by the ice:

[tex]Q_{water} = -Q_{ice[/tex]

[tex]T_f = (Q_{ice}/m_{ice}c_{ice} + Q_{water}/m_{water}c_{water}) + T_i[/tex]

Plugging in the values, we get:

[tex]T_f = (16700 J / 50 g * 2.1 J/gC + 100 g * 4.2 J/gC * (25C - T_i)) + T_i[/tex]

Simplifying this equation, we get:

[tex]T_f[/tex] = (835°C/g + 4200 J/°C + 105000 J/g) / (100 g * 4.2 J/g°C)

[tex]T_f[/tex]= (104035°C/g) / (420 J/°C)

[tex]T_f[/tex]= 247.7°C

Therefore, the final equilibrium temperature is approximately 247.7°C.

To calculate the percentage of ice that melts, we can use the equation:

% ice melted = (mass of ice melted / initial mass of ice) * 100%

mass of ice melted = [tex]Q_{ice} / L[/tex]

mass of ice melted = 16700 J / 334 J/g

mass of ice melted = 50 g

Therefore, the percentage of ice that melts is:

% ice melted = (50 g / 100 g) * 100%

% ice melted = 50%

Thus, the percentage of ice that melts is 50%.

Learn more about latent heat :

https://brainly.com/question/28044951

#SPJ4

0.99 moles of copper (Cu) would be made when 0.33 mole of copper (II) phosphide (Cu3P2) deteriorates.

Copper (II) phosphide (Cu3P2) is a compound that can be made through a reaction between copper and phosphorus under controlled conditions. It can also be made by the reaction between copper sulfate and sodium hypophosphite or by reducing copper (II) phosphate with carbon at high temperatures.

Copper (II) phosphide (Cu3P2) has several uses. It is used as a rodenticide to control rodents, as a catalyst, as a lubricant, as an alloying agent, and as a pigment in some ceramic glazes.

The decomposition of copper (II) phosphide (Cu3P2) can be represented by the following chemical equation Cu3P2 → 3Cu + 2P.

The number of moles of copper produced when 0.33 mole of copper (II) phosphide decomposes will be:

0.33 moles Cu3P2 / 1 x 3 moles Cu / 1 mole Cu3P2 = 0.99 moles Cu

So, 0.99 moles of copper (Cu) would be made when 0.33 mole of copper (II) phosphide (Cu3P2) deteriorates.

To know more about the moles, visit here:

https://brainly.com/question/14357742

#SPJ1

435.0 grams of ammonium nitrate is equivalent to 5.436 moles of the compound.To determine how many moles of ammonium nitrate are in 435.0 grams of the compound, we need to first determine the molar mass of ammonium nitrate and then use that value to convert grams to moles.

The molecular formula of ammonium nitrate is NH4NO3, which consists of one nitrogen atom, four hydrogen atoms, one oxygen atom, and three nitrogen atoms. To calculate the molar mass of NH4NO3, we can add up the atomic masses of each of these elements, taking into account the number of atoms of each element in the molecule.

The atomic masses are: nitrogen (N) = 14.01 g/mol, hydrogen (H) = 1.008 g/mol, and oxygen (O) = 16.00 g/mol.

Molar mass of NH4NO3 = (1 x 14.01 g/mol) + (4 x 1.008 g/mol) + (3 x 16.00 g/mol)

Molar mass of NH4NO3 = 80.04 g/mol

To convert 435.0 grams of NH4NO3 to moles, we can use the formula:

moles = mass (in grams) / molar mass

moles of NH4NO3 = 435.0 g / 80.04 g/mol

moles of NH4NO3 = 5.436 mol

Therefore, 435.0 grams of ammonium nitrate is equivalent to 5.436 moles of the compound.

Find out more about ammonium nitrate

brainly.com/question/10197458

#SPJ4

Answer:

Covalent bond

Explanation:

A covalent bond is a type of chemical bond where two or more atoms share electrons in order to form a bond between them. This bond results from the sharing of electrons in order to attain stability and full valence electron shells for each of the atoms involved. Covalent bonds are typically formed between non-metal elements and are known for their strength and stability.

Answer:

Covalent bond

Explanation:

A covalent bond is a type of chemical bond where two atoms share a pair of electrons in order to form a chemical bond. This bond is formed when the electron pair is shared equally between the two atoms, resulting in a stable and strong bond. Covalent bonds are typically found in compounds composed of non-metallic elements, such as oxygen, nitrogen, and carbon. These bonds are important in the formation of molecules and play a key role in biological processes.

The limiting reactant is calcium hydroxide. The maximum amount of calcium chloride that can be formed is 44.6 grams.

The balanced chemical equation for the reaction between calcium hydroxide and hydrochloric acid is:

Ca(OH)2 + 2HCl → CaCl2 + 2H2O

To determine the maximum amount of calcium chloride that can be formed, we need to identify the limiting reactant. The limiting reactant is the reactant that is completely consumed in the reaction, thus limiting the amount of product that can be formed.

We can determine the limiting reactant by calculating the amount of product that can be formed from each reactant and comparing the results.

First, let's calculate the amount of calcium chloride that can be formed from 27.8 grams of calcium hydroxide. We'll use the molar mass of calcium hydroxide to convert grams to moles, and then use the mole ratio between calcium hydroxide and calcium chloride to calculate the amount of calcium chloride that can be formed:

27.8 g Ca(OH)2 × (1 mol Ca(OH)2 / 74.093 g) × (1 mol CaCl2 / 1 mol Ca(OH)2) × (110.98 g CaCl2 / 1 mol CaCl2)

= 44.6 g CaCl2

Next, let's calculate the amount of calcium chloride that can be formed from 22.7 grams of hydrochloric acid. We'll use the molar mass of hydrochloric acid to convert grams to moles, and then use the mole ratio between hydrochloric acid and calcium chloride to calculate the amount of calcium chloride that can be formed:

22.7 g HCl × (1 mol HCl / 36.46 g) × (1 mol CaCl2 / 2 mol HCl) × (110.98 g CaCl2 / 1 mol CaCl2)

= 77.5 g CaCl2

From the calculations above, we can see that the amount of calcium chloride that can be formed from 27.8 grams of calcium hydroxide is 44.6 g, while the amount that can be formed from 22.7 grams of hydrochloric acid is 77.5 g. Therefore, the limiting reactant is calcium hydroxide.

The maximum amount of calcium chloride that can be formed is 44.6 grams.

Learn more about limiting reactant here:

https://brainly.com/question/14225536

#SPJ4

The brine a more effective de-ice solution than solid ice melt products is the correct option is : Since brine is already a solution, the Van't Hoff Factor is higher than solid salt, making the freezing point depression greater.

The Brine, is the concentrated salt solution, that is better to prevents and to eliminates the ice from the roads, but it can be more costly to store it. Since the brine is already the solution, the Van't Hoff Factor will be higher than the solid salt, the making is the freezing point depression is greater.

Freezing point depression requires a solution to occur. Brine starts as a solution, where solid salt must form a solution first.

To learn more about brine here

https://brainly.com/question/1493673

#SPJ4

The  compound will be isolated from the aqueous acidic solution that results from mixing 3 m HCl with the ether solution of the organic reactants is ethyl-4-aminobenzoate.

The insulation of organic composites is of particular interest to the oil painting, medicinal, ornamental, and alcohol product diligence. Achieving a good separation requires a conscious selection of the fashion to be used, depending on the physical parcels of the organic emulsion.

The compound that shows basic nature can be isolated in aqueous medium by mixing HCl solution.

Among the given (a) ethyl-4-aminobenzoate has a basic amino group which can react with HCl to form soluble salt that enters into aqueous medium.

So (a)  Ethyl 4-aminibenzoate.

Learn more about Isolated compound:

https://brainly.com/question/29361978

#SPJ4

Complete question:

According to the procedure for experiment 4C, which compound will be isolated trom the aqueous acidic solution that results from mixing 3 M HC with the ether solution of the arganic reactants?

A Ethyl 4-aminibenzoate

B 9 fluorenone

C benzoic acid

D the hydrochloride salt of benzoic acid

Orange juice has a pH of 3.5,Drain cleaner has a pH of 13.The pH scale is a measure of the acidity or basicity (alkalinity) of a solution, ranging from 0 (most acidic) to 14 (most basic), with 7 being neutral.

Based on the given pH values, we can classify each substance as acidic, basic, or neutral:

Orange juice has a pH of 3.5, which is below 7, indicating that it is acidic. Orange juice is acidic due to the presence of citric acid, which is a weak organic acid found naturally in citrus fruits.

Drain cleaner has a pH of 13, which is above 7, indicating that it is basic (alkaline). Drain cleaners are typically basic due to the presence of strong alkaline compounds such as sodium hydroxide (NaOH) or potassium hydroxide (KOH), which are used to dissolve clogs in drains and pipes.

In summary, based on their pH values, orange juice is acidic and drain cleaner is basic. It is important to note that both acids and bases can be harmful if not used or handled properly, and caution should always be exercised when working with them.

Find out more about pH scale

brainly.com/question/13934432

#SPJ4

C. Fast growth rate would be the most useful trait for these farmers.

Selective breeding is used to produce a crop with desired characteristics, such as a fast growth rate. A fast growth rate is beneficial to farmers in northern areas with short summer seasons because it allows the wheat to mature quickly and be harvested in a shorter amount of time, thus providing a larger yield despite the shorter growing season.Selective breeding is a process of selecting chemical compounds with specific desired properties and breeding them together to create a new compound with the desired traits. This is done by rearranging the chemical bonds between the two compounds and creating a new molecule with the desired characteristics. This process is known as chemical hybridization.

learn more about hybridization refer:brainly.com/question/8451085

#SPJ4

complete question:Scientists plan to use selective breeding to produce a new type of wheat for farmers who live in northern areas with short summer seasons. Which of these traits would be MOST useful for these farmers?

a.large seed size

b.long stem length

c.fast growth rate

d.shallow root systems

Maltose, which has the chemical formula C12H22O11, is created when three glucose molecules are joined together by dehydration processes.

Maltose, with the chemical formula C12H22O11, is created when dehydration events join three glucose molecules together.

Each glucose molecule that is bonded together during the dehydration event results in the removal of one water molecule. This joins the molecules together in a glycosidic bond, resulting in the disaccharide maltose.

By deducting the total number of water molecules lost from the combined molecular formula of the three glucose molecules, one may get the molecular formula of maltose. Three dehydration processes remove three molecules of water, each of which removes one. Maltose has the chemical formula (C6H12O6)3 - 3H2O, which is translated to C12H22O11 as a result.

learn more about molecules here:

https://brainly.com/question/19556990

#SPJ4

The molecular formula for glucose is C6H12O6. What would be the molecular formula for a molecule made by linking three glucose molecules together by dehydration reactions?

A 0.280M solution of [tex]KBr[/tex] in 16.743 L where 13.0 g of [tex]AgBr[/tex] must be precipitated in order to from an [tex]AgNO3[/tex] solution with 0.490 mol

Given the concentration of [tex]KBr[/tex] = 0.280M

The mass of [tex]AgBr[/tex] = 13g

The number of moles of [tex]AgNO3[/tex] is = 0.490

The volume of [tex]KBr[/tex] required = V

The volume of a 0.280 m solution of [tex]KBr[/tex] needed to precipitate 13.0 g of [tex]AgBr[/tex] from a solution containing 0.490 mol of [tex]AgNO3[/tex] is calculated using the following equation:

[tex]KBr+AgNO3--- > AgBr+KNO3[/tex]

Volume (L) = (Moles * Molar Mass [tex]AgBr[/tex]) / (Molarity [tex]KBr[/tex])

Volume (L) = (0.490 * (107.8682)) / (0.280 mol/L)

Volume (L) = 16.743 L

As a result, 13.0 g of AgBr must be precipitated from a solution containing 0.490 mol of [tex]AgNO3[/tex] using 16.743 L of a 0.280 m solution of [tex]KBr[/tex].

To learn more about AgBr click here https://brainly.com/question/14031729

#SPJ4

The change in enthalpy for the reaction of 4.00 g of CH4(g) burning in excess oxygen according to the reaction: CH4(g) + 2 O2(g) → CO2(g) + 2 H2O(g); H°rxn = –802.2 kj is  200.6 kJ.

Calculate the number of moles of CH4(g) using the molar mass of CH4(g):
4.00 g CH4(g) / 16.04 g/mol = 0.2494 mol CH4(g)

Use the balanced chemical equation to determine the ratio of moles of CH4(g) to the change in enthalpy:
1 mol CH4(g) : -802.2 kJ

Use the ratio to calculate the change in enthalpy for the given amount of CH4(g):
0.2494 mol CH4(g) x (-802.2 kJ / 1 mol CH4(g)) = -200.6 kJ

Therefore, the change in enthalpy for the reaction of 4.00 g of CH4(g) burning in excess oxygen is -200.6 kJ.

For more information about the change in enthalpy refers to the link:

https://brainly.com/question/13996238

#SPJ11

The observed phenomena is the result of a chemical interaction between aluminium and copper nitrate. The following happens when aluminium is added to a copper nitrate solution: 2Al + 3Cu(NO3)2 -> 3Cu + 2Al(NO3) (NO3) 3.

The inorganic substance copper nitrate solution has the vivid blue chemical formula Cu(NO3)2. It dissolves easily in water and easily separates into copper (Cu2+) and nitrate (NO3-) ions in solution. Copper nitrate solution is frequently employed in industrial processes like electroplating and as a catalyst in organic synthesis as well as laboratory studies. Moreover, it is employed in the manufacturing of a number of copper-based products, including copper oxide, copper hydroxide, and copper carbonate. While highly reactive, copper nitrate solution can be hazardous if handled improperly, especially when it comes into touch with combustible materials as this could result in the production of explosive compounds. As a result, it needs to be handled carefully and in a controlled environment.

Learn more about copper nitrate solution here:

https://brainly.com/question/15088874

#SPJ4

The likelihood of side reactions and the formation of byproducts during the nitration of methyl benzoate increases at higher temperatures due to the increased reactivity and concentration of the reactive species, and the decreased stability of the nitronium ion.

In the nitration of methyl benzoate reaction, the reaction is typically carried out by adding a mixture of concentrated nitric acid and sulfuric acid to methyl benzoate. This reaction is exothermic and the heat generated from the reaction can cause the reaction mixture to heat up.

At higher temperatures, there is an increased likelihood of side reactions occurring. One common side reaction that can occur during the nitration of methyl benzoate is the formation of byproducts such as dinitromethyl benzoate and trinitromethyl benzoate. These byproducts are formed when excess nitric acid reacts with methyl benzoate, rather than just a single nitro group being added to the benzene ring.

The formation of these byproducts is favored at higher temperatures because the reaction rate of the nitration reaction increases with temperature, and the concentration of the reactive species is higher at higher temperatures. This means that there is a greater likelihood of excess nitric acid being present and reacting with the methyl benzoate at higher temperatures, which can result in the formation of the unwanted byproducts.

Furthermore, the stability of the nitronium ion, which is the key reactive species in the nitration of methyl benzoate, decreases at higher temperatures. This can lead to the formation of other unwanted side products, such as benzene, due to the decomposition of the nitronium ion.

Learn more about nitronium here:

https://brainly.com/question/14803468

#SPJ4

The two major components, making up at least 3% each of the human body are Magnesium and Nitrogen.

Only six elements make up nearly all of the human body: oxygen, hydrogen, nitrogen, carbon, calcium, and phosphorus. The remaining mass is composed of sulfur, potassium, sodium, chlorine, and magnesium, which together make up around 0.85% of the total mass. These 11 components are all necessary components.

An adult's body has about 25 g of magnesium, with the majority of that amount found in soft tissues and 50–60% in the bones. Blood serum contains less than 1% of the total amount of magnesium, and these levels are closely monitored.

One of the primary elements in the body, nitrogen is necessary for the formation of various nitrogenous molecules, including hormones, neurotransmitters, and antioxidant defense components.

To know about elements

https://brainly.com/question/12009107

#SPJ4

The units that express specific heat capacity are J/(g°C), J/(gK), cal/(g°C), and cal/(gK). The J stands for joules, which is the SI unit of energy, g stands for gram, which is the SI unit of mass, °C stands for degrees Celsius, and K stands for Kelvin.

The cal stands for calorie, which is a non-SI unit of energy. Specific heat capacity is the amount of energy required to increase the temperature of a unit mass of a substance by one degree. It is usually expressed in joules per gram degree Celsius (J/g°C) or calories per gram degree Celsius (cal/g°C). The specific heat capacity of a substance is related to its molecular structure and the intermolecular forces that exist between its molecules. Substances that have strong intermolecular forces, such as those composed of molecules with multiple polar bonds, typically have higher specific heat capacities than substances with weak intermolecular forces, such as those composed of molecules with few or no polar bonds.

To know more about intermolecular forces please refer:

https://brainly.com/question/9007693

#SPJ4

Answer: If you add acid to a solution the concentration of hydrogen ions (acidity) increases and the pH decreases.

Explanation:

Answer:

The acidity of a solution increases with increasing concentration of hydrogen ions (H+). The concentration of H+ in a solution determines the pH of the solution, with lower pH values indicating a more acidic solution.

Explanation:

When a nonvolatile solute is added to a liquid, the concentration of the solute increases, which leads to a decrease in the vapor pressure of the solvent.

This is due to the fact that the solute particles occupy some of the space that would otherwise be filled by the solvent molecules. Since the solvent molecules have fewer spaces to escape into, the number of solvent molecules that escape into the air above the solution decreases, and therefore, the vapor pressure of the solvent decreases.

This decrease in vapor pressure is proportional to the concentration of the solute, and it is the basis for the phenomenon of vapor pressure lowering. This effect is important in many chemical and physical processes, such as boiling and evaporating, because it affects the temperature at which the solvent will boil.

To learn more about Nonvolatile solute :

https://brainly.com/question/29392465

#SPJ4

According to the Boyle's law, at constant temperature,  the pressure of

the gas is 1.99 atmospheres.

Boyle's law is an experimental gas law which describes the behavior of gas as  pressure of the gas decreases the volume increases. It's statement can be stated as, the absolute pressure which is exerted by a given mass of an ideal gas is inversely proportional to its volume provided temperature and amount of gas remains unchanged.

According to the equation the unknown pressure and volume of any one gas can be determined if two gases are to be considered.That is,given by the equation

P₁V₁=P₂V₂substitution of values gives

P₂= 1.15×215/124=1.99 atmospheres.

Thus,  at constant temperature,  the pressure of the gas is 1.99 atmospheres.

Learn more about Boyle's law,here:

https://brainly.com/question/1437490

#SPJ9

Answer:

yes I am good at the subject. That is my course

The ashes contain chemicals which have alkaline nature and the range of pH is from 10 to 12. Ashes are made up of atoms of different elements.

Ashes are defined as something which is left after burning or destroying some substances by fire. It is a greyish-white to black powder residue left when something is burned.

In the branch of analytical chemistry ashes are generally used to identify the mineral and metal content of the chemical samples. Ash is the non-liquid residue.

Ashes contain many atoms of the elements like carbon, calcium, magnesium, potassium, aluminium, phosphorous, etc.

Thus ashes are not remnants, it contains many atoms.

To know more about ash, visit;

https://brainly.com/question/9111555

#SPJ1

False. A sugar is classified as a D isomer if the hydroxyl group on its penultimate carbon (the second to last carbon) is oriented to the right in its Fischer projection.

In a Fischer projection, the horizontal lines represent bonds that are coming out of the plane of the paper, while the vertical lines represent bonds that are going into the plane of the paper. The orientation of the hydroxyl group on the penultimate carbon is determined by looking at the Fischer projection so that the

group is at the top, and the molecule is oriented vertically.

If the hydroxyl group on the penultimate carbon is oriented to the right in the Fischer projection, the sugar is classified as a D isomer. If the hydroxyl group on the penultimate carbon is oriented to the left in the Fischer projection, the sugar is classified as an L isomer.

It's worth noting that the position of the hydroxyl group on the carbon farthest from the carbonyl group does not affect whether a sugar is classified as a D or L isomer. This carbon is not the anomeric carbon, and it does not determine the overall stereochemistry of the molecule.

To know more about carbon :-

brainly.com/question/22530423

#SPJ4