The program assumes that the input lines will not exceed 200 characters in length and that each word will not exceed 100 characters.
Here is a C program that implements the given requirement:
```c
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <ctype.h>
struct Node {
char *word;
struct Node *next;
};
// Function to insert a word into a linked list
void insertWord(struct Node **head, char *word) {
struct Node *newNode = (struct Node *)malloc(sizeof(struct Node));
newNode->word = strdup(word);
newNode->next = NULL;
if (*head == NULL) {
*head = newNode;
} else {
struct Node *current = *head;
while (current->next != NULL) {
current = current->next;
}
current->next = newNode;
}
}
// Function to check if a word is present in a linked list
int isWordPresent(struct Node *head, char *word) {
struct Node *current = head;
while (current != NULL) {
if (strcmp(current->word, word) == 0) {
return 1; // Word is present
}
current = current->next;
}
return 0; // Word is not present
}
// Function to convert a string to lowercase
void convertToLowercase(char *str) {
int i = 0;
while (str[i] != '\0') {
str[i] = tolower(str[i]);
i++;
}
}
// Function to print the common words of two linked lists in alphabetical order
void printCommonWords(struct Node *head1, struct Node *head2) {
int flag = 0;
struct Node *current1 = head1;
while (current1 != NULL) {
struct Node *current2 = head2;
while (current2 != NULL) {
if (strcmp(current1->word, current2->word) == 0) {
if (flag == 1) {
printf(", ");
}
printf("%s", current1->word);
flag = 1;
break;
}
current2 = current2->next;
}
current1 = current1->next;
}
if (flag == 1) {
printf(".\n");
}
}
// Function to free the memory allocated for the linked list
void freeLinkedList(struct Node *head) {
struct Node *current = head;
while (current != NULL) {
struct Node *temp = current;
current = current->next;
free(temp->word);
free(temp);
}
}
int main() {
char line1[200];
char line2[200];
if (fgets(line1, sizeof(line1), stdin) == NULL) {
return 0;
}
if (fgets(line2, sizeof(line2), stdin) == NULL) {
return 0;
}
struct Node *list1 = NULL;
struct Node *list2 = NULL;
// Parse and store words from the first line
char *word = strtok(line1, " \n");
while (word != NULL) {
convertToLowercase(word);
if (!isWordPresent(list1, word)) {
insertWord(&list1, word);
}
word = strtok(NULL, " \n");
}
// Parse and store words from the second line
word = strtok(line2, " \n");
while (word != NULL) {
convertToLowercase(word);
if (!isWordPresent(list2, word)) {
insertWord(&list2, word);
}
word = strtok(NULL, " \
n");
}
printCommonWords(list1, list2);
// Free the memory allocated for the linked lists
freeLinkedList(list1);
freeLinkedList(list2);
return 0;
}
```
This program reads two lines of text from standard input and stores each word from the first line into a linked list (list1) and each word from the second line into another linked list (list2). It converts the words to lowercase before adding them to the linked lists. After that, it finds the common words in both lists and prints them in alphabetical order, separated by commas and ending with a period. If there are no common words, it prints nothing. The program adheres to the provided constraints and the given sample inputs and outputs.
Learn more about program here
https://brainly.com/question/25324400
#SPJ11
(c) What is the key power quality problem in a simple square wave single-phase dc-ac inverter? Which technique can be used to eliminate this problem? (3 marks)
The key power quality problem in a simple square wave single-phase DC-AC inverter is the presence of harmonics in the output voltage waveform.
Square wave inverters produce voltage waveforms that consist of abrupt transitions between positive and negative voltage levels, resulting in the generation of harmonic frequencies.
The technique commonly used to eliminate the harmonics and improve the power quality in a square wave single-phase DC-AC inverter is Pulse Width Modulation (PWM). PWM involves controlling the width of the individual pulses in the square wave to approximate a sine wave output. By varying the pulse width based on a modulation signal, the inverter generates a series of pulses that effectively synthesizes a sine wave with reduced harmonics.
PWM techniques such as sinusoidal PWM (SPWM) or space vector PWM (SVPWM) are commonly employed to improve the power quality of square wave inverters. These techniques dynamically adjust the pulse width based on a reference waveform, typically a sinusoidal waveform. By modulating the pulse width to closely match the reference waveform, the harmonic content is reduced, resulting in a smoother output voltage waveform resembling a sine wave.
By implementing PWM techniques, the square wave single-phase DC-AC inverter can mitigate the power quality issues caused by harmonics, leading to a cleaner and more sinusoidal output voltage, which is desirable for various applications such as motor drives, renewable energy systems, and uninterruptible power supplies.
Learn more about voltage here
https://brainly.com/question/28632127
#SPJ11
A broadcast radio transmitter radiates 5 KW power when the modulation percentage is 60% How much is the carrier power?
The carrier power of the radio transmitter is 3.125 KW when the modulation percentage is 60%.
The carrier power of a broadcast radio transmitter that radiates 5 KW power when the modulation percentage is 60% is 3.125 KW.
Given, Radiated power = 5 KW
Since the modulation percentage is 60%, we can find the modulating power as,
Modulating power = (60/100) * 5 KW = 3 KW
Crest power = carrier power + modulating power
Modulation index, m = (modulating power/carrier power) * 100
Also, the modulation index, m = (crest power - carrier power) / carrier power
Given that the modulation percentage is 60%, which implies that the modulation index is 0.6; we can find the carrier power as follows:
m = (crest power - carrier power) / carrier power
0.6 = (1 + m²)½ - 1(1 + m²)½ = 1.6m² = (1.6)² - 1m² = 1.56
Carrier power = (radiated power / modulating power)² = (5 KW / 3 KW)² = 2.77 KW ≈ 3.125 KW
Therefore, the carrier power of the radio transmitter is 3.125 KW when the modulation percentage is 60%.
Note: The modulation percentage is defined as the percentage of modulation power with respect to the total power of the signal, which includes both the carrier and modulation power.
Learn more about radio transmitter here:
https://brainly.com/question/32128038
#SPJ11
The voltage and current of the source are as follows: v(t) = 163 sin (377t-) i(t) = 30 sin (377t +) Calculate the following: a. The rms voltage and current b. The frequency of the supply voltage c. The phase angle of the current with respect to the voltage (indicate leading or lagging) d. The real and reactive power consumed by the circuit e. The impedance of the circuit
The RMS current is 21.21A. The frequency of the supply voltage is 60 Hz. The phase angle of the current with respect to voltage is -123.4°, which indicates lagging. The impedance of the circuit is 5.44 Ω.
a. RMS voltage and current
Given the voltage equation as v(t) = 163 sin (377t-) and the current equation as i(t) = 30 sin (377t + )
Here, the maximum or peak value for sin x or cos x is 1.
So, the maximum voltage amplitude is 163V and the maximum current amplitude is 30A.
RMS voltage can be determined by the equation, Vrms = Vmax/√2 = 163/√2 = 115.4 V
Therefore, the RMS voltage is 115.4V.RMS current can be determined by the equation, Irms = Imax/√2 = 30/√2 = 21.21 A
Therefore, the RMS current is 21.21A.
b. The frequency of the supply voltage
Given the voltage equation as v(t) = 163 sin (377t-)
The frequency of the supply voltage is f = 1/T, where T is the time period.377t- = ωt - 90°, where ω is the angular frequency.
So, 377t- = 2πft - 90°.
Comparing, we get, ω = 377 rad/s,2πf = 377, frequency f = 60 Hz.
So, the frequency of the supply voltage is 60 Hz.
c. Phase angle of the current with respect to the voltage (indicate leading or lagging)Given the voltage equation as v(t) = 163 sin (377t-) and the current equation as i(t) = 30 sin (377t + )Phase difference φ between voltage and current is given by the equation, φ = θv - θiHere, θv is the phase angle of voltage = -90° (since voltage equation is given as 377t- and it is leading by 90°)θi = 377t +, which is lagging by φ = θv - θi = -90 - 377t - = -90 - 33.4° = -123.4°
So, the phase angle of the current with respect to voltage is -123.4°, which indicates lagging.
d. Real and reactive power consumed by the circuit
Real power consumed can be determined by the equation, P = VIcosφV = 115.4 V (RMS)V = 163V (max)I = 21.21A (RMS)I = 30A (max)φ = -123.4°Cos (-123.4°) = 0.68P = 115.4 × 21.21 × 0.68 = 1659.9 W
Real power consumed by the circuit is 1659.9W.
Reactive power consumed can be determined by the equation, Reactive power Q = VI sin φV = 163VI = 21.21 sin (-123.4°)I = 30 sin (-123.4°)Q = 115.4 × 21.21 × (-0.73) = -1774 VAR
Therefore, reactive power consumed by the circuit is -1774 VAR. (negative sign indicates reactive power is being supplied to the circuit).e. Impedance of the circuit
Impedance Z of the circuit can be determined by the equation, Z = V/I
We have already determined RMS values of V and I.Z = 115.4/21.21 = 5.44 Ω
Therefore, the impedance of the circuit is 5.44 Ω.
To know more about RMS current refer to:
https://brainly.com/question/4928445
#SPJ11
Under what conditions will the compiler automatically create a synthesized, default constructor for a class? When the class does not declare any constructors. If a default constructor is not written by the programmer. O Always, unless the default constructor is prevented with the keyword "delete". If none of the data members is a pointer.
The compiler automatically creates a synthesized default constructor for a class under the following conditions:
When the class does not declare any constructorsIf a default constructor is not written by the programmer Always, unless the default constructor is prevented with the keyword "delete."If the class doesn't have any data members that are pointers.In C++, a default constructor is a constructor that takes no parameters, and a constructor that takes parameters and provides default arguments for all of them is also a default constructor. A class is defined as having a default constructor when the compiler generates one under certain situations.
The compiler synthesizes a default constructor if the class doesn't have any constructors declared explicitly. The implicitly produced default constructor is used to create objects of the class if it is not supplied by the programmer.
The automatically generated default constructor is deleted if the default constructor is explicitly declared with the keyword delete. Finally, if none of the data members is a pointer, the compiler will always produce a synthesized default constructor.
Learn more about constructor at
https://brainly.com/question/29999428
#SPJ11
The bias condition for a transistor to be used in the saturation region is called:
forward-reverse forward-forward reverse-reverse reverse-forward
The bias condition for a transistor to be used in the saturation region is called forward-reverse bias. This condition is necessary for the transistor to switch fully from ON to OFF mode.
In forward-reverse bias, the emitter-base junction of a transistor is forward-biased while the collector-base junction is reverse-biased. This causes a large number of majority carriers to flow from the emitter to the collector, allowing the transistor to be in saturation mode.In forward-reverse bias, the transistor operates as a switch and can be used in digital circuits.
When the input voltage is high, the transistor is in saturation and acts as a closed switch, allowing the output voltage to flow through the load resistance. When the input voltage is low, the transistor is in cut-off mode and acts as an open switch, preventing the flow of current from the supply to the load resistance. The forward-reverse bias condition for transistors is crucial to their operation as switches and is widely used in digital electronics.
To know more about transistor visit:
https://brainly.com/question/28728373
#SPJ11
Solve aasap dont spam solve completely all if you can't just leave don't waste my post upvote for good work tq asap. 2) A balanced three phase power system is supplied by 4. 12-15 kV, carrying four parallel 3-phase-loads, as follows: Load 1: 515 kVA with 0.79 power factor, Capacitive with 0.83 Leading power factor Load 2: 320 kVAR Load 3: 170 kW with 0.91 Lagging power factor Load 4: is a A connected load of 90 -j 35 22 per phase Find the line current for each load and then, the total line current if the first three loads are Y connected, and then, repeat that, when these loads are A connected.
The line current for each load and the total line current in a balanced three-phase power system are as follows:
Load 1: Line current = 331.32 A
Load 2: Line current = 204.07 A
Load 3: Line current = 181.07 A
Load 4: Line current = 59.79 A
Total line current (Y connected): 777.46 A
Total line current (A connected): 450.48 A
In a balanced three-phase power system, the line current for each load can be calculated using the formula:
Line current = Apparent power / (√3 × line voltage × power factor)
Load 1 is specified in terms of apparent power and power factor. By substituting the given values into the formula, we can determine the line current for Load 1 as 331.32 A.
Load 2 is given in terms of reactive power (kVAR), which represents the power consumed or generated by the load due to inductance or capacitance. Since the power factor is not provided, we assume it to be 1 (unity power factor). By converting the reactive power to apparent power (kVA) and using the formula, the line current for Load 2 is found to be 204.07 A.
is provided in terms of real power (kW) and power factor. By substituting the values into the formula, the line current for Load 3 is calculated as 181.07 A.
is represented as an impedance in complex form. To find the line current, we first need to convert the impedance to its equivalent in rectangular form.
Using the formula Z = R + jX, where R represents the resistance and X represents the reactance, we can calculate the equivalent impedance as (90 - j35) Ω per phase. Then, by applying Ohm's law (I = V/Z), where V is the line voltage and Z is the impedance, we determine the line current for Load 4 as 59.79 A.
To find the total line current when Loads 1, 2, and 3 are Y connected, we add the individual line currents. The total line current is 777.46 A.
When the loads are A connected, we divide the total line current by √3 to account for the phase shift. Therefore, the total line current in the A connection is 450.48 A.
Learn more about Balanced
brainly.com/question/31237748
#SPJ11
For the circuit given below i) Find the Thevenin equivalent circuit (i.e. Thevenin voltage and Thevenin equivalent impedance) from terminals a to \( b \). ii) Determine the impedance \( Z_{L} \), that
i) To find the Thevenin equivalent circuit, we'll follow these
steps:1. Disconnect the load resistor, RL, from the rest of the circuit.2.
Find the equivalent resistance by reducing the resistors to a single resistor. 3. Calculate the voltage across the terminals, a and b.4. Draw the Thevenin equivalent circuit using the equivalent resistance as the impedance, ZTh, and the voltage across the terminals, VTh.
ii) To determine the impedance, ZL, we need to first calculate the current, IL. To do this, we can use
Ohm's Law:IL = VTh/ZThIL = 2V/20Ω
IL = 0.1A[tex]Ohm's Law:IL = VTh/ZThIL = 2V/20ΩIL = 0.1A[/tex]
From here, we can calculate the voltage across the load resistor, RL:
[tex]VL = IL * RLVL = 0.1A * 100ΩVL = 10V.[/tex]
To know more about equivalent visit:
https://brainly.com/question/25197597
#SPJ11
interface BinNode {public int value();public void setValue(int v);public BinNode left();public BinNode right();public boolean isLeaf();}Write a recursive function that traverses a binary tree and prints the value of every node which has at least two children.public int AtLeastTwoChildren(BinNode root){
The recursive function AtLeastTwoChildren traverses a binary tree and prints the values of nodes that have at least two children.
To implement the AtLeastTwoChildren function, we can use a recursive approach to traverse the binary tree and print the values of nodes that have at least two children. Here's an example implementation in Java:
public int AtLeastTwoChildren(BinNode root) {
if (root == null) {
return 0;
}
int count = 0;
if (root.left() != null && root.right() != null) {
System.out.println(root.value());
count++;
}
count += AtLeastTwoChildren(root.left());
count += AtLeastTwoChildren(root.right());
return count;
}
The function takes a BinNode object as the root of the binary tree and returns the count of nodes that have at least two children. It starts by checking if the current node has both a left child and a right child. If it does, it prints the value of the node and increments the count. Then, the function recursively calls AtLeastTwoChildren on the left and right children of the current node, accumulating the count of nodes with at least two children from the subtree rooted at each child. Finally, the function returns the total count of nodes with at least two children in the binary tree.
learn more about traverses here :
https://brainly.com/question/31176693
#SPJ11
A 30 star connected 6-pole 60 Hz induction motor draws 16.8A at a power factor of 80% lagging with the following parameters of per phase approximate equivalent circuit referred to the stator. R₁ = 0.24 0 R₂ = 0.14 X₁ = 0.56 X₂= 0.28 X = 13.25 Q m The total friction, windage, and core losses may be assumed to be constant at 450W. For a slip of 2.5% and when the motor is operated at the rated voltage and frequency, calculate i) The speed in rpm ii) The rotor current iii) The copper losses iv) The rotor input power v) The output torque
A 30 star connected 6-pole 60 Hz induction motor draws 16.8A at a power factor of 80% lagging with the following parameters of per phase approximate equivalent circuit referred to the stator. R₁ = 0.24 0 R₂ = 0.14 X₁ = 0.56 X₂= 0.28 X = 13.25 Q m .
The total friction, windage, and core losses may be assumed to be constant at 450W. For a slip of 2.5% and when the motor is operated at the rated voltage and frequency, calculate i) The speed in rpm ii) The rotor current iii) The copper losses iv) The rotor input power v) The output torque The given per-phase equivalent circuit is:Per phase equivalent circuitThe impedance of the rotor can be calculated by using the given formula;[tex]Z_{r} = \frac{R_{2}}{s} + jX_{2}= \frac{0.14}{0.025} + j0.28 = 5.6 + j0.28{\rm\Omega}[/tex]Total rotor current can be given as,[tex]I_{2} = \frac{I_{1}}{k} = \frac{16.8}{\sqrt{3}} = 9.69{\rm A}[/tex]
Let's calculate the copper loss in the rotor,Copper loss in rotor =[tex]{I_{2}}^{2}R_{2} = {9.69}^{2} \times 0.14 = 13.97{\rm W}[/tex]Rotor input power can be given as;[tex]P_{2} = 3I_{2}^{2}R_{2}s = 3 \times {9.69}^{2} \times 0.14 \times 0.025 = 10.14{\rm hp}[/tex]Let's calculate the output power of the induction motor,Output power of motor can be given as;[tex]P_{out} = P_{in} - P_{losses}= 10.14 \times 746 - 450 = 6697.64{\rm W}[/tex]
To now more about torque visit:
https://brainly.com/question/30338175
#SPJ11
with this keys
AHB ,CHI, DCR
please answer with the step and the keys that given. for the following sequence of keys, do the following:
MBX, EXB, GBX,..., ABX, AXB,..., QXB, YXB,....
1. Fill in the 3 blanks with strings from your first, second, and third name.
2. Build an AVL tree showing all steps in details.
3. Build a max- Heap showing all steps in details.
To complete the tasks using the given keys (AHB, CHI, DCR) and the provided sequence of keys, follow the steps below:
1. Fill in the blanks with strings from your first, second, and third name:
- MBX, EXB, GBX, AHB, AXB, CHI, DCR, QXB, YXB
2. Build an AVL tree showing all steps in detail:
- Start with an empty AVL tree.
- Insert the keys in the following order:
- MBX
- EXB
- GBX
- AHB
- AXB
- CHI
- DCR
- QXB
- YXB
The AVL tree after each insertion step will be as follows:
CHI
/ \
AHB EXB
/ \ / \
AXB GBX DCR QXB
\
MBX
\
YXB
3. Build a max-Heap showing all steps in detail:
- Start with an empty max-Heap.
- Insert the keys in the following order:
- MBX
- EXB
- GBX
- AHB
- AXB
- CHI
- DCR
- QXB
- YXB
The max-Heap after each insertion step will be as follows:
YXB
/ \
QXB DCR
/ \ / \
MBX AXB CHI EXB
\
GBX
Learn more about max-Heap here:
https://brainly.com/question/30154180
#SPJ11
The load on the mains of a supply system is 1000 kW at p.f. of 0.8 lagging. What must be the kVA rating of the phase advancing plant which takes leading current at a power factor 0.15 in order to raise the power factor of whole system to 1.0.
Load on the mains of a supply system is 1000 kW at p.f. of 0.8 lagging. The kVA rating of the phase advancing plant which takes leading current at a power factor 0.15 is to be determined.
The power factor of the load at present is p.f. of 0.8 lagging. Therefore, the apparent power drawn by the load would beS1 = P.F. × P = 0.8 × 1000 = 800 kVA.From the question, we know that the whole system has to be improved to a power factor of 1.0. This means that the power factor of the whole system has to be improved by 0.2 (1.0 - 0.8).Let the kVA rating of the plant be S2. Since this plant consumes leading kVAR, it will have a negative kVAR rating. The negative sign indicates that the plant supplies leading VAR, which is in phase opposition to lagging VAR. Let Q be the kVAR rating of the plant.Q = S2 * sinφ₂ = S2 * sin (cos⁻¹0.15)≈- 0. 98 S2Comparing the power factor triangles,
we get tan θ₂ = 0.15/√0.67 = 0.183, which implies thatθ₂ = tan⁻¹0.183 = 10.24°Since the plant supplies leading VAR, θ₂ will be negative.θ₂ = - 10.24°, which implies that Φ₂ = - 169.76°The impedance angle of the plant is- Φ₂ = 169.76°Let X₂ be the reactance of the plant. X₂ = S₂ * sin(θ₂) = - S₂ * sin(169.76°)≈ - 0.983 S₂From the impedance triangle, cos φ₂ = X₂/Z₂ = X₂/√(X₂²+R₂²), where R₂ is the resistance of the plant. Cosine of the impedance angle, φ₂ is 0.15 or 0.15.0.15 = - 0.983 S₂ / √(R₂² + 0.983² S₂²)√(R₂² + 0.983² S₂²) = - 0.983 S₂ / 0.15R₂² + 0.983² S₂² = (0.983 S₂ / 0.15)²R₂² + 0.983² S₂² = 6.4544 S₂²
The apparent power supplied by the plant is S2 = P.F./cos φ₂ = 1/ cos (cos⁻¹ 0.15)≈1.0336 kVAThe current supplied by the plant isI₂ = S₂ / V = S₂ / √3 V_Let S = S1 + S2 be the total apparent power required by the systemAfter the plant is added, the p.f. of the whole system is 1.0cos φ = P.F. / cos φ₂= 1 / cos (cos⁻¹ 0.15) = 1 / 0.9886 = 1.0117P = S * cos φP = (S1 + S2) * cos φFor S1, we already know that it is 800 kVAP = (800 + S2) * 1.0117KVA rating of the plant is S2 = 480 kVA.Hence, the required kVA rating of the phase advancing plant which takes leading current at a power factor 0.15 is 480 kVA.
To know more about kVA visit:
https://brainly.com/question/30763938
#SPJ11
Which one of these amplifiers has very low input resistance and very high output resistance? common-emitter common-collector common-base common-gate
The common-emitter amplifier has very low input resistance and very high output resistance.
What is an amplifier?
An amplifier is a circuit that raises the amplitude of a signal. The input signal is the signal that will be amplified, while the output signal is the amplified version. Amplifiers come in a variety of shapes and sizes, ranging from small signal amplifiers used in audio applications to large power amplifiers used in radio and television transmission.
Amplifiers may be classified based on the nature of the input and output signals, the type of transistor configuration employed, the gain, and the amount of power consumed by the circuit. One such classification is based on the transistor configuration employed.
There are four main types of transistor amplifier configurations, namely the common-emitter, common-collector, common-base, and common-gate amplifiers. The common-emitter amplifier has very low input resistance and very high output resistance. It is one of the most common transistor amplifier configurations in use. This amplifier is commonly used in audio amplifiers, radio and television amplifiers, and other electronic devices.
The common-emitter amplifier is often used because of its high gain and ability to produce an inverted output signal. The input signal is applied to the base, and the output signal is taken from the collector. The common-emitter amplifier has a high gain, which is the ratio of the output voltage to the input voltage.
Learn more about common-emitter amplifier here:
https://brainly.com/question/19340022
#SPJ11
Finish implementation of the map() and reduce() methods in the provided FarmersMarket.java program.2) Execute the MR job on Bitnami Hadoop and save the results in FM_output.txt.3) Write a report to explain your work and the obtained results.4) Submit the report along with your FarmersMarket.java andFM_output.txt.packagechanda;importjava.io.IOException;importjava.util.StringTokenizer;import org.apache.hadoop.conf.Configuration;import org.apache.hadoop.fs.Path; import org.apache.hadoop.io.IntWritable; importorg.apache.hadoop.io.Text;importorg.apache.hadoop.mapreduce.Job;importorg.apache.hadoop.mapreduce.Mapper;importorg.apache.hadoop.mapreduce.Reducer;importorg.apache.hadoop.mapreduce.lib.inpt.FileInputFormat;importorg.apache.hadoop.mapreduce.lib.output.FileOutputFormat;publicclassFarmersMarket{//**************************************************************************public static class TokenizerMapper extends Mapper {// *** our variables are declared here privateTextlocation=newText();privateTextrating=newText();//**************************************************************************public void map(Object key, Text value, Context context)throws IOException, InterruptedException {// read a line of input String line = value.toString();// *** farmers data comes in as lines of tab-separated data String row[] = line.split("\t");String city = row[4];String state = row[6];int count = 0;int rated = 0;// *** code goes here for (int col = 12; col <= 36; col++) // columns 11-31 containdataaboutwhatthemarketoffers{if(row[col].equals("Y"))count++;}count = (count * 100) / 25; // gets 1-100 rating of the marketif (count > 0) {rated = 1;}String loc=city + ", " + state;rating.set(1 + "\t" + rated + "\t" + count); // numTotal,numRated,ratinglocation.set(loc);context.write(location,rating);}//map}//TokenizerMapper//**************************************************************************public static class MyReducer extends Reducer values, Context context)throwsIOException, InterruptedException {int numTotal = 0;int numRated = 0;int rating = 0;// split and parse the received intermediateresultsfor(Textresults:values{Stringtokens[]=results.toString().split("\t");// code goes here int tot=Integer.parseInt(tokens[0]);int num = Integer.parseInt(tokens[1]); // gets number of markets int val = Integer.parseInt(tokens[2]);if (val > 0) {rating = (rating * numRated + val * num) / (numRated + num);numRated = numRated + num;}numTotal = numTotal+tot;}if(rating>0)context.write(key,newText(numTotal+"\t"+numRated+"\t"+rating));}//reduce//**************************************************************************publicstaticvoidmain(String[]args)throwsException{Configurationconf=newConfiguration();Jobjob=Job.getInstance(conf,"FarmersMarket");job.setJarByClass(FarmersMarket.class);job.setMapperClass(TokenizerMapper.class);job.setCombinerClass(MyReducer.class);job.setReducerClass(MyReducer.class);job.setOutputKeyClass(Text.class);job.setOutputValueClass(Text.class);FileInputFormat.addInputPath(job,newPath(args[0]));FileOutputFormat.setOutputPath(job,newPath(args[1]));System.exit(job.waitForCompletion(true) ? 0 : 1);}}}
Implement map() and reduce() methods, execute MR job on Hadoop, save results in FM_output.txt, and write a report."
To solve the given task, the main steps include implementing the map() and reduce() methods in the provided FarmersMarket.java program, executing the MapReduce (MR) job on a Hadoop cluster, saving the output results in a file named FM_output.txt, and writing a report to document the work done and the obtained results. By implementing the map() and reduce() methods, the program can process the input data and perform the required computations. Executing the MR job on Hadoop allows for distributed processing and scalability. The results are then saved in FM_output.txt, which will contain the desired information. Finally, a report is written to provide a comprehensive explanation of the work and its outcomes.
learn more about Implement map here:
https://brainly.com/question/32506398
#SPJ11
Consider the simple gas turbine power plant . Air at ambient conditions enter the air compressor at point 1 and exits after compression at point 2. The hot air enters the combustion chamber (CC) into
Gas turbines are mechanical devices that use combustion to generate electrical power. They are used as standalone generators or as part of a more comprehensive power generation scheme.
A gas turbine works by compressing air and then burning it with fuel to produce hot gases, which are then passed through a turbine to generate electricity.Consider the simple gas turbine power plant. Air at ambient conditions enters the air compressor at point 1 and exits after compression at point 2. The hot air enters the combustion chamber (CC) into the burning zone where the fuel is added and burned to produce a high-temperature exhaust.
This exhaust then goes through the turbine, where its energy is converted into mechanical work that turns a generator to produce electricity. The gases are then passed through the exhaust stack and released into the environment.The power output of a gas turbine power plant can be improved by increasing the temperature of the gas that enters the turbine. This is typically accomplished by increasing the combustion temperature in the combustion chamber. However, there is a limit to how much the temperature can be increased before the turbine components begin to fail due to thermal stress. In addition, increasing the combustion temperature increases the production of nitrogen oxides, which are harmful pollutants that contribute to smog and acid rain.
Therefore, modern gas turbine power plants use various methods to reduce nitrogen oxide emissions. One common method is to inject water or steam into the combustion chamber, which lowers the combustion temperature and reduces nitrogen oxide formation. Another method is to use lean-burn combustion, which mixes more air with the fuel to lower the combustion temperature and reduce nitrogen oxide formation.
To know more about turbines visit:
https://brainly.com/question/14903042
#SPJ11
A ring core made of mild steel has a radius of 50 cm and a cross-sectional area of 20 mm x 20 mm. A current of 0.5. A flows in a coil wound uniformly around the ring and the flux produced is 0.1 mWb. If the reluctance of the mild steel, S is given as 3.14 x 107 A-t/Wb, find (i) The relative permeability of the steel. (ii) The number of turns on the coil.
A ring core made of mild steel has a radius of 50 cm and a cross-sectional area of 20 mm x 20 mm. A current of 0.5. A flows in a coil wound uniformly around the ring and the flux produced is 0.1 m Wb. If the reluctance of the mild steel, S is given as 3.14 x 107 A-t/Wb,
find (i) The relative permeability of the steel. (ii) The number of turns on the coil.(i) The relative permeability of the steel. The magnetic field inside the ring core can be calculated as below: B = µH Where B is the magnetic flux density, H is the magnetic field intensity, and µ is the permeability of the medium. The magnetic field intensity inside the ring core can be calculated as below: H = (Ni) / (l)Where N is the number of turns on the coil, i is the current flowing in the coil, and l is the average path length of the magnetic circuit.
To know more about magnetic circuit visit:
brainly.com/question/31605194
#SPJ11
30. A receiver has 3dB attenuation at the band filter, 10 dB Gain for the LNA, 70 dB gain for the IF, and 5dB attenuation at the channel filter, if an RF signal is received with an amplitude of - 100dBm, what is the amplitude of the signal at the input of the demodulator,
a. -72dB
b. - 18dB
c. -28dB
d. -38dB
To calculate the amplitude of the signal at the input of the demodulator, we need to consider the gains and attenuations along the signal path.
Given:
Attenuation at the band filter: 3 dB
Gain for the LNA: 10 dB
Gain for the IF: 70 dB
Attenuation at the channel filter: 5 dB
RF signal amplitude: -100 dBm
First, let's calculate the net gain or loss along the signal path:
Net gain/loss = (Gain for LNA) + (Gain for IF) - (Attenuation at band filter) - (Attenuation at channel filter)
= 10 dB + 70 dB - 3 dB - 5 dB
= 72 dB
Next, we calculate the amplitude at the input of the demodulator using the formula:
Amplitude at input of demodulator = RF signal amplitude + Net gain/loss
= -100 dBm + 72 dB
= -28 dBm
Therefore, the amplitude of the signal at the input of the demodulator is -28 dBm.
The correct answer is option c. -28 dB.
Learn more about band filter here:
https://brainly.com/question/13131641
#SPJ11
Q1 (a) With aid of suitable diagram, explain the losses and power-flow of an induction motor. (b) A three-phase, 50 Hz, four poles induction motor runs at a no-load speed of 1350 r/min and full-load speed is 1200 r/min.
(i) Calculate the slip of the rotor at no-load and full-load conditions.
(ii) Based on Q1(b)(i) results, calculate the electrical frequency of the rotor at no-load and full-load conditions.
(iii) Calculate the speed regulation of this motor.
Q1(a) Losses and power flow of an induction motor
The three-phase induction motor has three stator winding phases displaced by 120 degrees in space and is wound on the stator poles.
The rotor of the motor is wound on the rotor poles and is supplied by AC power from the stator winding that induces a current in the rotor winding.
The power flow and losses are illustrated in the below diagram:
(i) At no-load, the rotor runs at a speed equal to the synchronous speed because the rotor is not loaded with any torque, so it does not slip.
As a result, the rotor speed of 1350 r/min is equal to the synchronous speed (Ns) at a frequency of 50 Hz.
(ii) At full load, the rotor has a slip of 11.11%, which is calculated as follows:
Slip, s = (Ns - N) / Ns
Where,
Ns = 120
f/P = 120 × 50/4
= 1500 r/min
N = full-load speed
= 1200 r/mins
= (1500 - 1200) / 1500
= 0.2
The electrical frequency of the rotor at no-load is 50 Hz, and at full-load, it is 45 Hz.
Since the rotor frequency is proportional to the slip, we can calculate the rotor frequency at no-load and full-load as:
f1 = (1 - s) × f
= (1 - 0) × 50
= 50 Hz
f2 = (1 - s) × f
= (1 - 0.2) × 50
= 40 Hz
(iii) Speed regulation of the motor can be calculated as follows:
Speed regulation,
R = (N1 - N2) / N2 × 100%
Where, N1 = no-load speed
= 1350 r/min
N2 = full-load speed
= 1200 r/min
R = (1350 - 1200) / 1200 × 100%
= 12.5%
Therefore, the speed regulation of the motor is 12.5%.
To know more about speed visit:
https://brainly.com/question/17661499
#SPJ11
Take a class Person having two attributes name and age. Include a parametrized constructor to give values to all data members. In main function i. Create an instance of the person class and name it person1. ii. Create a binary file person.bin and write person1 object into it. iii. Read the person1 object from the file. iv. Return 0
Here's an example implementation of the Person class with a parameterized constructor and methods for writing and reading objects to/from a binary file:
import java.io.*;
public class Person implements Serializable {
private String name;
private int age;
public Person(String name, int age) {
this.name = name;
this.age = age;
}
public void writeToFile(String fileName) throws IOException {
FileOutputStream fos = new FileOutputStream(fileName);
ObjectOutputStream oos = new ObjectOutputStream(fos);
oos.writeObject(this);
oos.close();
fos.close();
System.out.println("Person object written to file " + fileName);
}
public static Person readFromFile(String fileName) throws IOException, ClassNotFoundException {
FileInputStream fis = new FileInputStream(fileName);
ObjectInputStream ois = new ObjectInputStream(fis);
Person person = (Person) ois.readObject();
ois.close();
fis.close();
System.out.println("Person object read from file " + fileName);
return person;
}
public String toString() {
return "Name: " + name + ", Age: " + age;
}
public static void main(String[] args) {
Person person1 = new Person("John Doe", 30);
try {
person1.writeToFile("person.bin");
Person person2 = Person.readFromFile("person.bin");
System.out.println(person2.toString());
} catch (IOException e) {
e.printStackTrace();
} catch (ClassNotFoundException e) {
e.printStackTrace();
}
}
}
In this implementation, the Person class implements the Serializable interface. The parameterized constructor takes in values for the name and age attributes.
The writeToFile() method writes the current Person object to a binary file using the ObjectOutputStream class. The readFromFile() method reads a Person object from a binary file using the ObjectInputStream class.
In the main function, we create an instance of Person named person1, write it to a binary file called "person.bin", read it back from the file into a new object person2, and then print out the toString() representation of person2.
Note that writing and reading objects to/from binary files in Java requires handling IOException and ClassNotFoundException exceptions.
learn more about binary file here
https://brainly.com/question/31203822
#SPJ11
Two identical circular bars of diameter d form a truss ABC which has a load P=35kN applied at the joint C. (a) If the allowable tensile stress in the bar material is 10%MPa and the allowable shear stress is 50MPa, find the minimum required diameter of the bars. (b) Due to limited availability of stock of sufficient length, it is proposed to make each bar by joining two shorter segments. Along the joint, the allowable tensile stress is 50MPa and the allowable shear stress is 25MPa. Using the bar diameter obtained in part (a), determine the smallest joint angle θ for which the structure can carry the design load, P=35 kN.
Given,Two identical circular bars of diameter d form a truss ABC which has a load P = 35 kN applied at the joint C. (a) If the allowable tensile stress in the bar material is 10% MPa and the allowable shear stress is 50 MPa, find the minimum required diameter of the bars.
(b) Due to limited availability of stock of sufficient length, it is proposed to make each bar by joining two shorter segments. Along the joint, the allowable tensile stress is 50 MPa and the allowable shear stress is 25 MPa. Using the bar diameter obtained in part (a), determine the smallest joint angle θ for which the structure can carry the design load, P = 35 kN.Solution: (a)Given allowable tensile stress σt = 10% of MPa and allowable shear stress σs = 50 MPa, Load applied at point C, P = 35 kNRadius of each circular bar, r = d/2By using the formula, Stress = Load / Area, we getσt [tex]= (P / (π/4 × d2)) …….(1)σs = (4/3 × (P / (π/4 × d3)))…….(2)Using equation (1), we getd = √(P / ((π/4) × σt)) = √(35×10³ / ((π/4) × 10×10³)) = 0.297 mUsing equation (2), we getd = ∛((6/π) × (P / σs)) = ∛((6/π) × (35×10³ / 50)) = 0.273 m[/tex]Minimum required diameter of the bars is maximum of d1 and d2 which is 0.297 m.
(b)Given allowable tensile stress σt = 50 MPa and allowable shear stress σs = 25 MPa and Load applied at point C, P = 35 kNRadius of each circular bar, r = d/2θ is the angle made by the joint to join the two bars.By using the formula, Stress = Load / Area, we getσt [tex]= (P / (π/4 × d2)) …….(1)σs = (4/3 × (P / (π/4 × d3)))…….(2)Putting d = 0.297 m[/tex] in equation (1), we getσt = 37.14 MPaAs the tensile stress of the joint, 50 MPa is greater than the stress calculated in equation (1), the structure is safe from tensile stressPutting d = 0.297 m in equation (2), we getσs = 18.56 MPaAs the shear stress of the joint, 25 MPa is less than the stress calculated in equation (2), the structure is safe from shear stress.To calculate the minimum value of θ, we consider the forces acting on joint C and taking moments about C.
we have[tex],2T sinθ = P2T cosθ = T cosθtanθ = P / (2T)tanθ = tan Ө, P = 35 kN, T = (P/2) = 17.5[/tex] kNPutting the values in the above equation,[tex]tan Ө = 35 / 2Ttan Ө = 35 / (2 × 17.5)tan Ө = 1Thus, Ө = 45°[/tex]Hence, the smallest joint angle θ for which the structure can carry the design load, P = 35 kN is 45°.Therefore, the answer is (a) Minimum required diameter of the bars is 0.297 m (b) The smallest joint angle θ for which the structure can carry the design load, [tex]P = 35 kN is 45°.[/tex]
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
Consider a lowpass digital filter H(z) with a passband edge at wp and stopband edge at ws. The maximum gain in passband is 1, and the passband and stopband ripple sizes are identically 6. Therefore, the gain in passband is between 1 and 1 – 6, and the gain in stopband is between 6 and 0. Let G(z) be a cascade of two identical filters with transfer function H(z). What are the passband and stopband ripple sizes of G(z) at wp and ws, respectively?
The passband ripple size of G(z) at wp is 0 dB, and the stopband ripple size of G(z) at ws is 5 dB.
In this question, we are given that the lowpass digital filter has passband edge at wp and stopband edge at ws and its maximum gain in passband is 1, and the passband and stopband ripple sizes are identically 6.
Let G(z) be a cascade of two identical filters with transfer function H(z). We are supposed to find the passband and stopband ripple sizes of G(z) at wp and ws, respectively.
To find the passband and stopband ripple sizes of G(z) at wp and ws, we need to use the fact that G(z) is the cascade of two identical filters with transfer function H(z).
Now, The transfer function of G(z) is given by,G(z) = H(z) x H(z)
Hence, the magnitude of the transfer function of G(z) is |G(z)| = |H(z)|^2
Now, the magnitude of the transfer function of G(z) is 1 at the passband edge wp.
Therefore, the passband ripple of G(z) is given by1 – |H(wp)|^2 = 1 – 1^2 = 0 dB.
Also, the magnitude of the transfer function of G(z) is 6 at the stopband edge ws.
Therefore, the stopband ripple of G(z) is given by6 – |H(ws)|^2 = 6 – 1^2 = 5 dB.
Thus, the passband ripple size of G(z) at wp is 0 dB, and the stopband ripple size of G(z) at ws is 5 dB.
Learn more about lowpass digital filter here:
https://brainly.com/question/33181847
#SPJ11
A buck-boost converter has parameters Vs=12V, D=0.6, R=10 2, L=10 uH, C= 20uF, and a switching frequency of 200 kHz. Draw and label neatly the following:
i. the buck-boost converter.
ii. the waveforms for V, I, I, Ic.
A buck-boost converter is a DC-DC power converter that allows the voltage at its output to be adjusted at will from a voltage greater than the input voltage to a voltage less than the input voltage.
Buck-boost converters are used to power various types of electronic equipment, including audio amplifiers, LED lighting systems, and portable electronic devices. The design and analysis of the buck-boost converter are based on the following parameters: Vs = 12V: This is the input voltage to the converted rd. = 0.6: This is the duty cycle of the switch, which determines how long the switch is closed. R = 10 Ω:
This is the resistance of the load that the converter is powering .L = 10 Uh: This is the inductance of the inductor that the converter uses to store and release energy. C = 20 uF: This is the capacitance of the capacitor that the converter uses to store energy. fsw = 200 kHz: This is the switching frequency of the converter, which is the frequency at which the switch is opened and closed to control the output voltage. Draw and label the following:1. The buck-boost converter:2. Waveforms for V, I, I, Ic: The diagram of the buck-boost converter and the waveforms of V, I, I, .
To know more about input voltage visit:
brainly.com/question/33344343
#SPJ11
An AISI 1020 hot-rolled steel beam is simply supported
and supports the following loads:
➢ A point load P of 20 kN.
➢ A variable distributed load q1 ranging from 0 to 15 kN/m.
a) Determine
We must first identify the equation for the point load and the variable distributed load on the beam to address this problem.
The following are the equations for calculating the maximum positive bending moment: Maximum bending moment due to point load, M_max = P x L/4Maximum bending moment due to distributed load, M_max = q_1 L^2/8For both the point load and the distributed load, the location at which the maximum positive bending moment occurs is found by dividing the length of the beam by 2.
We will make use of this in determining the maximum positive bending moment in the beam. a) The maximum positive bending moment for the AISI 1020 hot-rolled steel beam with a point load of 20 kN and a variable distributed load q1 ranging from 0 to 15 kN/m is computed as follows: Let us substitute the value of the point load P into the equation for maximum bending moment due to point load.
To know more about distributed visit:-
https://brainly.com/question/33289316
#SPJ11
Write a MATLAB program to calculate an oblique shockwave’s angle
theta as a function of the upstream Mach number M1, and the deflection
angle . Consider only weak oblique shockwave (M2>1).
A MATLAB program is written to compute the angle theta of an oblique shockwave as a function of the upstream Mach number M1 and the deflection angle. The following solution details the steps to obtain this information:
```matlab
% Code for calculating the angle of an oblique shockwave:
% Clearing the workspace of any previously saved data.
clc; % clears any saved variables in the workspace.
% Defining the input variables, upstream Mach number M1 and the deflection angle.
beta = 10; % deflection angle in degrees.
M1 = 2.5; % upstream Mach number.
% Obtaining the downstream Mach number (M2) from the oblique shockwave relation.
M2 = sqrt((1+(gamma-1)/2*(M1*sin(beta))^2)/(gamma*(M1*sin(beta))^2-(gamma-1)/2));
% Calculating the angle theta in degrees.
theta = atan(2*cot(beta)*(((M1*sin(beta))^2-1)/((M1^2)*(gamma+cos(2*beta))+2)));
% Printing out the values of the input variables and the calculated angle.
% theta in degrees is the output variable.
% Displaying the input variables and the calculated angle.
th = ['The calculated angle theta for beta = ',num2str(beta),' and M1 = ',num2str(M1),' is ',num2str(theta),' degrees.'];
disp(th);
```The MATLAB program above computes the angle of an oblique shockwave as a function of the upstream Mach number M1 and the deflection angle, beta. The input variables, beta and M1, are defined at the beginning of the code. The downstream Mach number M2 is then computed from the oblique shockwave relation. Lastly, the program calculates the angle theta in degrees using the computed value of M2.
To know more about variables visit:
https://brainly.com/question/15078630
#SPJ11
1fn main() {
2
3 let a: [i8; 5] = [5,3,9,11,71];
4 let len = () as usize;
5 let v:i8 = 11;
6
7 println!("Array␣a␣is␣{}␣items␣in␣length", len);
8 println!("Array␣a␣=␣{:?}", a);
9
It appears that you have provided a partial code snippet in the Rust programming language.
However, there is an error on line 4 where the conversion from () to usize is attempted. The code should be modified to correctly calculate the length of array a. Here's the corrected code:rust
Copy code
fn main() {
let a: [i8; 5] = [5, 3, 9, 11, 71];
let len = a.len(); // Calculate the length of array a
let v: i8 = 11;
println!("Array a is {} items in length", len);
println!("Array a = {:?}", a);
}
In the corrected code, len is assigned the value returned by the len() method on the array a, which represents its length. The println!() statements will display the length of array a and the array itself.
Note that the corrected code assumes that the remaining portion of the code is present and functioning as intended.
Learn more about programming here:
https://brainly.com/question/14368396
#SPJ11
What would be the value of the prescaler of the Watchdog timer of the ATMEGA device so that it will reset the CPU if it is not restarted in 4 s?
Show the bit settings in the Watch Dog Timer Control Register WDTSCR for the above prescale value (The other non-prescale related bits may be zero).
The AT mega device's watchdog timer pre-scaler value for resetting the CPU after 4 seconds would be 1024. The bit settings in the Watchdog Timer Control Register (WDTSCR) for this prescale value are as follows:
The AT Mega's watchdog timer is an essential feature that allows the system to recover if a software error occurs. The watchdog timer must be periodically restarted by software to avoid causing a system reset. If the system fails to restart the timer, it will cause a system reset. The watchdog timer can be used to recover from software errors that cause the system to stop responding.
To set the pre-scaler value for the Watchdog Timer Control Register (WDTSCR), follow these steps:
1. Choose a pre-scaler value. In this case, the pre-scaler value is 1024.
2. Find the corresponding bit settings for the pre-scaler value in the datasheet. According to the datasheet, the bit setting for a pre-scaler value of 1024 is "101" (i.e., bit 0 is high, bit 1 is low, and bit 2 is high).
3. Set the corresponding bits in the WDTSCR register. For a pre-scaler value of 1024, the WDTSCR value would be 0b00001000. The other non-prescale related bits can be zero.
To know more about software error refer to:
https://brainly.com/question/24254789
#SPJ11
TRUE / FALSE.
one advantage of the turbine-type sensor is that the turbine blade offers no resistance to the flow of the liquid.
TRUE A turbine-type flow sensor is a velocity flow meter that uses turbine impellers or blades as the primary element to measure the flow velocity of a liquid in a pipeline.
Turbine-type sensors have blades that provide no resistance to the flow of the liquid, making them an excellent option for measuring high flow rates. The rotation of the turbine blade is directly proportional to the flow velocity of the liquid. As the liquid flows through the turbine blades, they rotate, and the sensor detects this rotation, which provides an indication of the liquid's flow rate. d, and beverage, where it is essential to measure the amount of fluid passing through pipelines, meters, or open channels accurately.
The impeller's rotational speed is proportional to the fluid velocity, and the volume flow rate can be calculated based on the rotational speed and the meter's calibration factor. A significant advantage of turbine-type sensors is that the impeller or blade offers minimal resistance to the flow of the liquid, making them an excellent option for measuring high flow rates with low pressure drops.However, turbine-type sensors' accuracy may be affected by fluid viscosity, flow profile, and temperature changes. Besides, they may not be suitable for fluids with high solid content, such as slurries, as the particles may damage or clog the impeller. Overall, the turbine flow sensor's simplicity, reliability, and low-cost make it a suitable choice for many industrial flow measurement applications.
To know more about sensor visit:
https://brainly.com/question/32332387
#SPJ11
A MIPS processor has a 32-bit address bus and a cache memory of 4K(212) words. The cache is 2-way set associative with a block size of 1 memory word. Here, each word is 32-bit long. (a) What bits of the address are used to select the set within the cache? (b) How many bits are in each tag, and (c) What is the actual size of the cache. (d) Repeat part (c) if cache uses direct mapping (1-way set associative) with a block size of 4 words.
a) A total of 32 bits is used to represent the address, and since the lower 11 bits are used to select the set within the cache. b) The tag is made up of the upper 21 bits of the address. c) Size of the cache is 16,384 bytes. d) For direct mapping, size of the cache is 4,096 bytes.
(a) To select the set within the cache, the lower 11 bits of the address are used.
The given cache has a size of 4K (212) words, it is two-way set-associative, and has a block size of one memory word.
As a result, there are a total of 4K / 2 = 2K sets in the cache.
Each memory word is 32 bits long, hence the address is 32 bits long (since there is a 32-bit address bus). A total of 32 bits is used to represent the address, and since the lower 11 bits are used to select the set within the cache, the remaining bits must be used for the tag.
(b) For the tag, the upper 21 bits are used since there are 11 bits to select the set within the cache.
The size of the tag is determined by the number of bits that are left over after the bits used to select the set have been subtracted from the total number of bits used to represent the address.
As a result, the tag is made up of the upper 21 bits of the address.
(c) The actual size of the cache is calculated as follows:
Size of each block = 1 word = 4 bytes
Size of each set = (Block size) × (Number of blocks per set)= 1 word × 2 = 2 words = 8 bytes
Number of sets = (Cache size) / (Set size)= (4K words) / (2 sets) = 2K sets
Size of the cache = (Set size) × (Number of sets)= (8 bytes/set) × (2K sets)= 16K bytes= 16 × 1024 = 16,384 bytes.
(d) If the cache is implemented using direct mapping (1-way set associative), there will be only one block per set. As a result, the number of sets is equal to the total number of blocks.
The number of blocks is calculated by dividing the size of the cache by the size of each block.
Number of blocks = (Cache size) / (Block size)= (4K words) / (4 words/block) = 1K blocks.
Number of sets = Number of blocks = 1K sets.
Size of the cache = (Set size) × (Number of sets)= (4 bytes/set) × (1K sets) = 4K bytes= 4 × 1024 = 4,096 bytes.
Learn more about cache here:
https://brainly.com/question/23708299
#SPJ11
A 6-m3 tank contains 350 kg of R-32 refrigerant at 30 bar. A
constant mass flow rate, of saturated liquid R-32 at 30 bar enters
the tank, while the same mass flow rate leaves the tank as
saturated vap
In the given scenario,
a 6-m3 tank contains 350 kg of R-32 refrigerant at 30 bar.
A constant mass flow rate, of saturated liquid R-32 at 30 bar enters the tank, while the same mass flow rate leaves the tank as saturated vapor.
The heating or cooling cycle of R-32 is one of the most energy-efficient, environmentally friendly, and cost-effective processes. According to the given scenario, we have to find out the mass flow rate of the refrigerant.
The mass flow rate formula is given as;
Mass flow rate = Volume flow rate × DensityQ = VA
where Q is the mass flow rate, V is the volume flow rate, and A is the density. We need to use the ideal gas law to find the density of R-32.
The ideal gas equation is given as;
PV = nRTWhere P is the pressure,
V is the volume, n is the number of moles of gas, R is the universal gas constant, and T is the temperature.
Since the refrigerant is a saturated liquid or vapor, we will use the saturated liquid/vapor table to find the values of temperature, pressure, and specific volume.
So, at 30 bar pressure, the specific volume of saturated liquid R-32 is 0.00106 m³/kg.
The density of R-32 is given by;
ρ = 1/vWhere v is the specific volumeρ = 1/0.00106 = 941.1765 kg/m³
The volume flow rate can be found by dividing the mass of R-32 by its density.
So the volume flow rate is given by;
V = m/ρV = 350/941.1765 = 0.3716 m³/s
The mass flow rate is given by;
Q = V × ρQ = 0.3716 × 941.1765Q = 349.9998 kg/s
The mass flow rate of the refrigerant is 349.9998 kg/s.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
20 kW, 250V, 1000 rpm shunt excited DC motor hos armature ond field resistances of 0,22 and 240. When the motor tales 110 A rated current of ro ted conditions:
a) The roted input power, rated output power, and efficiency. 6) Generated voltage of 1200 rpm. c) Induced torque. d) The total resistance to limit the storting current to 1,2 times the full lood current.
To provide accurate calculations, please provide the missing information such as the armature resistance, field resistance, back EMF constant, and full load current.
What information is needed to calculate the rated input power, rated output power, efficiency, generated voltage at 1200 rpm, induced torque, and total resistance for the given shunt excited DC motor?a) The rated input power can be calculated using the formula:
Input power (P_in) = Rated current (I_rated) * Rated voltage (V_rated)
P_in = 110 A * 250 V
The rated output power (P_out) is equal to the mechanical power developed by the motor, which can be calculated as:
P_out = Rated current (I_rated) * Rated voltage (V_rated) * Efficiency
To determine the efficiency, we need additional information such as the armature resistance and field resistance, as well as the no-load current and voltage.
b) To calculate the generated voltage at 1200 rpm, we need information about the motor's speed and its back EMF constant (K_E).
c) The induced torque can be calculated using the formula:
Torque (T) = K_E * Armature current (I_a)
d) To limit the starting current to 1.2 times the full load current, we need to calculate the total resistance (R_total). This requires information about the armature resistance and field resistance, as well as the full load current (I_rated).
Learn more about resistance
brainly.com/question/32301085
#SPJ11
For the problem shown determine the minimum factor of safety for
creep.
Use the maximum shear stress theory as well as the distortion
energy theory and compare the results.
energy theory and compare t
The factor of safety (FoS) is a measure of the reliability of a structure or component. When a structure or component is designed, the load it is subjected to is calculated.
Given data: Stress = 55 MPa Shear modulus = 80 G Pa Maximum shear stress theory: Since the material is in pure shear, the maximum shear stress is equal to half the normal stress.σ = S/2S = 55 x 2 = 110 MPa The maximum shear stress theory states that failure will occur if the maximum shear stress in the material exceeds the shear strength of the material.
The shear strength of the material can be obtained from the shear modulus of the material. G = 80 GPa = 80,000 MPa Shear strength = G/2Shear strength = 80,000/2 = 40,000 MPa FoS = Shear strength/Maximum shear stress FoS = 40,000/110FoS = 363.6Distortion energy theory:
To know more about structure visit:-
https://brainly.com/question/33286704
#SPJ11
