cubical tank 1 meter on each edge is filled with water at 20 degrees C. A cubical pure copper block 0.46 meters on each edge with an initial temperature of 100 degrees C is quickly submerged in the water, causing an amount of water equal to the volume of the smaller cube to spill from the tank. An insulated cover is placed on the tank. The tank is adiabatic. Estimate the equilibrium temperature of the system (block + water). Be sure to state all applicable assumptions.

Answers

Answer 1

Answer:

final temperature = 26.5°

Explanation:

Initial volume of water is 1 x 1 x 1 = 1 [tex]m^{3}[/tex]

Initial temperature of water = 20° C

Density of water = 1000 kg/[tex]m^{3}[/tex]

volume of copper block = 0.46 x 0.46 x 0.46 = 0.097 [tex]m^{3}[/tex]

Initial temperature of copper block = 100° C

Density of copper = 8960 kg/[tex]m^{3}[/tex]

Final volume of water = 1 - 0.097 = 0.903 [tex]m^{3}[/tex]

Assumptions:

since tank is adiabatic, there's no heat gain or loss through the wallsthe tank is perfectly full, leaving no room for cooling airtotal heat energy within the tank will be the summation of the heat energy of the copper and the water remaining in the tank.

mass of water remaining in the tank will be density x volume = 1000 x 0.903 = 903 kg

specific heat capacity of water c = 4186 J/K-kg

heat content of water left Hw = mcT = 903 x 4186 x 20 = 75.59 Mega-joules

mass of copper will be density x volume = 8960 x 0.097 = 869.12 kg

specific heat capacity of copper is 385 J/K-kg

heat content of copper Hc = mcT = 869.12 x 385 x 100 = 33.46 Mega-joules

total heat in the system = 75.59 + 33.46 = 109.05 Mega-joules

this heat will be distributed in the entire system

heat energy of water within the system = mcT

where T is the final temperature

= 903 x 4186 x T = 3779958T

for copper, heat will be

mcT = 869.12 x 385 = 334611.2T

these component heats will sum up to the final heat of the system, i.e

3779958T + 334611.2T = 109.05 x [tex]10^{6}[/tex]

4114569.2T = 109.05 x [tex]10^{6}[/tex]

final temperature T = (109.05 x [tex]10^{6}[/tex])/4114569.2 = 26.5°


Related Questions

An eddy current separator is to separate aluminum product from an input streamshredded MSW. The feed rate to the separator is 2,500 kg/hr. The feed is known to contain174 kg of aluminum and 2,326 kg of reject. After operating for 1 hour, a total of 256 kg ofmaterials is collected in the product stream. On close inspection, it is found that 140 kg ofproduct is aluminum. Estimate the % recovery of aluminum product and the % purity of thealuminum produc

Answers

Answer:

the % recovery of aluminum product is 80.5%

the % purity of the aluminum product is 54.7%

Explanation:

feed rate to separator = 2500 kg/hr

in one hour, there will be 2500 kg/hr x 1 hr = 2500 kg of material is fed into the  machine

of this 2500 kg, the feed is known to contain 174 kg of aluminium and 2326 kg of rejects.

After the separation, 256 kg  is collected in the product stream.

of this 256 kg, 140 kg is aluminium.

% recovery of aluminium will be = mass of aluminium in material collected in the product stream ÷ mass of aluminium contained in the feed material

% recovery of aluminium = 140kg/174kg x 100% = 80.5%

% purity of the aluminium product = mass of aluminium in final product ÷ total mass of product collected in product stream

% purity of the aluminium product = 140kg/256kg

x 100% = 54.7%

You are tasked with designing a thin-walled vessel to contain a pressurized gas. You are given the parameters that the inner diameter of the tank will be 60 inches and the tank wall thickness will be 5/8" (0.625 inches). The allowable circumferential (hoop) stress and longitudinal stresses cannot exceed 30 ksi.
(1) What is the maximum pressure that can be applied within the tank before failure? = psi(2) If you had the opportunity to construct a spherical tank having an inside diameter of 60 inches and a wall thickness of 5/8" (instead of the thin-walled cylindrical tank as described above), what is the maximum pressure that can be applied to the spherical tank? = psi

Answers

Answer:

Explanation:

For cylinder

Diameter d = 60 inches

thickness t = 0.625 inches

circumferential (hoop) stress = 30 ksi

[tex]hoop \ \ stress =\sigma_1=\frac{P_1d}{2t}\\\\\sigma_1=30ksi\\\\30000=\frac{P_1\times 60}{2\times0.625}\\\\P_1=624psi[/tex]

[tex]longitudinal \ \ stress =\sigma_2=\frac{P_2d}{2t}\\\\\sigma_2=30ksi\\\\30000=\frac{P_2\times 60}{4\times0.625}\\\\30000=\frac{P_2\times 60}{2.5}\\\\75000=P_2\times60\\\\P_2=\frac{75000}{60} \\\\P_1=1250psi[/tex]

Therefore maximum pressure without failure is P₁ = 625 psi

ii) For Sphere

[tex]\sigma_1=\sigma_2=\frac{Pd}{4t} \\\\P=\frac{30000\times 4 \times 0.625}{60} \\\\=\frac{75000}{60}\\\\=1250\ \ psi[/tex]

What's the "most common" concern with using variable frequency drives (VFDs)? 1) carrier frequency 2) harmonic distortion 3) hertz modulation

Answers

Also I want the answer please

The common" concern with using variable frequency drives (VFDs) is C. hertz modulation.

What is variable frequency drive?

It should be noted that a variable frequency drive simply means a type of motor drive that us used in mechanical drive system.

In this case, common" concern with using variable frequency drives (VFDs) is hertz modulation

Learn more about frequency on:

brainly.com/question/6985885

#SPJ9

Choose two consumer services careers and research online to determine what kinds of professional organizations exist for these professions. Write a paragraph describing the purpose of the organization, the requirements for joining, and the benefits of membership.

Answers

Bank loan facilitator, and hospital emergency care specialist are the two consumer or customer services careers.

Bank loan facilitator is a consumer service facilitator who ask and provide people loan in emergency, for the purpose of education, treatment, family events, and for other reasons. For bank loan facilitator the professional organizations should be banking and finance sector. The purpose of these organizations is to help people in financial matter seeking benefit by getting interest from customers. The requirements for joining of the employee must include strong convincing power for the employee, time management, strong and tactful communication skills. Benefits of membership of the customers can help them to seek loans on need basis on lower interest. Hospital emergency care specialist provides help to the staff and the customers in medical emergency. These professionals are necessary for the hospital, clinics, and rehabilitation centers. Purpose of the organization is to provide medical care to the patients. The requirements for joining of the employee includes ability to give information to patients and staff during emergency conditions, facilitating ambulance to rescue patients from their homes, and from other areas, providing medicine, medical equipment, and other facilities to the patients and other medical staff necessary for treatment. Benefits of membership in clinical or hospital settings can help the patient in frequent visits for treatment, concession in laboratory tests, and medication.

Learn more about customer:

https://brainly.com/question/13735743

The Rappahannock River near Warrenton, VA, has a flow rate of 3.00 m3/s. Tin Pot Run (a pristine stream) discharges into the Rappahannock at a flow rate of 0.05 m3/s. To study mixing of the stream and river, a conserva- tive tracer is to be added to Tin Pot Run. If the instruments that can mea- sure the tracer can detect a concentration of 1.0 mg/L, what minimum concentration must be achieved in Tin Pot Run so that 1.0 mg/L of tracer can be measured after the river and stream mix? Assume that the 1.0 mg/L of tracer is to be measured after complete mixing of the stream and Rappa- hannock has been achieved and that no tracer is in Tin Pot Run or the Rap- pahannock above the point where the two streams mix. What mass rate (kg/d) of tracer must be added to Tin Pot Run?

Answers

Find the given attachments for complete explanation

An isentropic steam turbine processes 5.5 kg/s of steam at 3 MPa, which is exhausted at 50 kPa and 100°C. Five percent of this flow is diverted for feedwater heating at 500 kPa. Determine the power produced by this turbine. Use steam tables.

Answers

Answer:

The answer is 1823.9

Explanation:

Solution

Given that:

m = 5.5 kg/s

= m₁ = m₂ = m₃

The work carried out by the energy balance is given as follows:

m₁h₁ = m₂h₂ +m₃h₃ + w

Now,

By applying the steam table we have that<

p₃ = 50 kPa

T₃ = 100°C

Which is

h₃ = 2682.4 kJ/KJ

s₃ = 7.6953 kJ/kgK

Since it is an isentropic process:

Then,

p₂ =  500 kPa

s₂=s₃ = 7.6953 kJ/kgK

which is

h₂ =3207.21 kJ/KgK

p₁ = 3HP0

s₁ = s₂=s₃ = 7.6953 kJ/kgK

h₁ =3854.85 kJ/kg

Thus,

Since 5 % of this flow diverted to p₂ =  500 kPa

Then

w =m (h₁-0.05 h₂ -0.95 )h₃

5.5(3854.85 - 0.05 * 3207.21  - 0.95 * 2682.4)

5.5( 3854.83 * 3207.21 - 0.95 * 2682.4)

5.5 ( 123363249.32 -0.95 * 2682.4)

w=1823.9

While having a discussion about O-rings at the bottom of filters, Technician A says that the Automotive Filter Manufacturers Council recommends that the filter O-ring be lubricated with oil after installing the filter. Technician B says that the filter O-ring should be lubricated before installation. Who is correct

Answers

Answer:

Technician B is correct

Explanation:

O- rings are used with oil transmission filters to avoid transmission failures but some people use  lip seals as well. either of them is  inserted onto the outer part of the transmission system i.e it is inserted/found in-between Transmission filters and the transmission systems and it main purpose is to avoid leaks and transmission failure in the short and long term.

0-rings should be lubricated before installation this is because the o-rings are usually super tight when installing and would require lubrication to ease the installation process else the rubber might get ruptured and this would lead to instant transmission failure.

WHAT IS A VACUOMETER?

Answers

It is a tool used to measure Low pressure
It is a tool to measure low pressure

Solid spherical particles having a diameter of 0.090 mm and a density of 2002 kg/m3 are settling in a solution of water at 26.7C. The volume fraction of the solids in the water is 0.45. Calculate the settling velocity and the Reynolds number.

Answers

Answer:

Settling Velocity (Up)= 2.048*10^-5 m/s

Reynolds number Re = 2.159*10^-3

Explanation:

We proceed as follows;

Diameter of Particle = 0.09 mm = 0.09*10^-3 m

Solid Particle Density = 2002 kg/m3

Solid Fraction, θ= 0.45

Temperature = 26.7°C

Viscosity of water = 0.8509*10^-3 kg/ms

Density of water at 26.7 °C = 996.67 kg/m3

The velocity between the interface, i.e between the suspension and clear water is given by,

U = [ ((nf/ρf)/d)D^3] [18+(1/3)D^3)(1/2)]

D = d[(ρp/ρf)-1)g*(ρf/nf)^2]^(1/3)

D = 2.147

U = 0.0003m/s (n = 4.49)

Up = 0.0003 * (1-0.45)^4.49 = 2.048*10^-5 m/s

Re=0.09*10^-3*2.048*10^-5*996.67/0.0008509 = 2.159*10^-3

Other Questions
What architecture is known for its large stained glass windows Which strategies could be used to reverse the current trend occurring in the United States check all that apply Enforce regulations for drivers who do not obey cyclists lanes on roadways Assess roadways for more bicycle safety lanes and crosswalk signals Redone certain regions to improve traffic flow and reduce congestion for drivers Allocate funding to promote health fairs that advertise bicycle safety and gear Educate the community about the need to drive more slowly on roadways who founded the Safavid empire at the age of 14 years old Three consecutive integers have a sum of 45. Find the integers. There is a clerk at the butcher shop, he is five feet ten inches tall, and he wears size 13 sneakers. He has a wife and 2 kids. What does he weigh? Complete this sentence."Lequel" is used to replace quel + ______.a nouna verban adjectivean adverb pleas help please helpppp Russia let the Finns do exactly as they wanted.True or False? Which sentence is punctuated correctly? A. There were only three questions left when the teacher said "Okay, pencils down." B. There were only three questions left when the teacher said, "Okay, pencils down." C. There were only three questions left when the teacher said "Okay pencils down". D. There were only three questions left when the teacher said, "Okay pencils down". How many faces does the rectangular solid have?8264 1) Factor x2 +7x+ 10. Which of the following is thebest antonym for"conjecture"?A. estimateB. assumeC. proveD. speculate There are two red jars of marbles and one blue jar of marbles. Jars of a certain color have the same number of marbles in them. There are 30 marbles in total. The difference between the number of marbles in a red jar and the number of marbles in a blue jar is 12. Find the number of marbles in each type of jar. Any help would be great do honey bee produce propolis? A. Complete the sentencesIUse words from page 1 to complete the sentences.1. The2. We have to3. #BlackLivesMatter wantsis second-degree murder.peacefully and passionately,for black people all over the world.a police officer of a crime, you need a very strong case.? He didn't do anything wrong.4. To5. Why are you putting him in1.2.3.4.5. Which one of these plans would NOT be considered a "fad" diet?The grapefruit diet (where you eat grapefruit with every meal)O Atkins (very low carbs, high on protein and fats)Weight Watchers (you can eat anything, but count total calories)O A diet where you can only eat certain foods at certain times of the day Which expression is equivalent to LAT QUESTION AND LAST TRY!!! WILL GIVE BRANLIEST!!!! AT LEAST TAKE A LOOK, SHARE YO SMARTNESSS!!!!!!!! PLS4. All angles are formed by the intersection of two _______ at a point called the angle's vertex.A) raysB) linesC) segmentsTHE HINT I WAS GIVEN: These objects have start with an endpoint and end with a line. What is the product of 7/9 and 1/4