The shell lands 90.8 meters past the edge of the cliff when fired at 32.6 m/s and 43.0 degrees.
To tackle this issue, we can involve the conditions of movement for shot movement, which depict the movement of an article that is sent off up high and moves affected by gravity.
In the first place, we really want to break the underlying speed of the shell into its flat and vertical parts. The point of 43.0 degrees over the flat implies that the upward part of the speed is given by:
v_y = v * sin(43.0°)
Also, the even part of the speed is given by:
v_x = v * cos(43.0°)
where v is the underlying speed of the shell, which is given as 32.6 m/s in the issue articulation.
Presently, we can involve the condition for the even distance went by a shot:
x = v_x * t
where x is the flat distance went by the shell, and t is the time it takes for the shell to arrive on the ground. We can make the opportunity t by involving the condition for the upward distance went by a shot:
y = v_y * t - 0.5 * g * t^2
where y is the upward distance gone by the shell, g is the speed increase because of gravity (which is roughly 9.81 m/s^2 close to the outer layer of the Earth), and we can set y equivalent to the level of the bluff, 25.0 m.
Addressing for t, we get:
t = (v_y + sqrt(v_y^2 + 2 * g * y))/g
Subbing the qualities we have:
t = (v * sin(43.0°) + sqrt((v * sin(43.0°))^2 + 2 * 9.81 * 25.0))/9.81
t = 3.89 s (adjusted to two decimal spots)
Presently, we can find the even distance went by the shell:
x = v_x * t
x = 32.6 * cos(43.0°) * 3.89
x = 90.8 m (adjusted to two decimal spots)
Accordingly, the shell lands 90.8 meters past the edge of the bluff.
To learn more about projectile motion and kinematics, refer:
https://brainly.com/question/14674370
#SPJ4
The complete question is:
A cannon, located 60.0 m from the base of a vertical 25.0 m tall cliff, shoots a 15 kg shell at 43.0 ❝ above the horizontal toward the cliff.
v=32.6 m/s
The ground at the top of the cliff is level, with a constant elevation of 25.0 m above the cannon. Under the conditions of part A, how far does the shell land past the edge of the cliff?
what is the total charge of all the electrons in a 20 kg bar of aluminum? (aluminum has 13 electrons per atom and an atomic mass of 27 u .)
Given that Aluminum has 13 electrons per atom and an atomic mass of 27 u, we can use Avogadro's number (6.022 × 10^23 atoms/mole) to calculate the number of aluminum atoms in the 20 kg bar.
27 g/mol (atomic mass) x 1 kg / 1000 g = 0.027 kg/mol
The number of moles of aluminum in the 20 kg bar:
20 kg / 0.027 kg/mol = 740.74 moles
Finally, we can calculate number of aluminum atoms:
[tex]740.74 moles * 6.022 × 10^23[/tex] atoms/mole = [tex]4.460 * 10^26[/tex] atoms
4.460 × 10^26 atoms x 13 electrons/atom x 1.602 × 10^-19 coulombs/electron = 1.167 × 10^7 coulombs.
The total charge of all the electrons in a 20 kg bar of aluminum is approximately 1.167 × 10^7 coulombs.
To know more about Avogadro's number
https://brainly.com/question/13302703
#SPJ4
A student with a mass of 75.0 kg is sitting on 4-legged lab stool that has a mass of 3.0 kg. Each leg of the stool is circular and has a diameter of 2.50 cm. Find the pressure under each leg of the stool. (Hints: (1) Remember to convert cm² to m² for the area of the legs of the stool. (2) Remember that the stool has four legs. (3) Note that the problem gives the diameter of the legs of the stool, not the radius.)
The pressure under each leg of the stool is approximately 149,675 Pa, or 149.675 kPa.
The pressure under each leg of the stool is approximately 37,419 Pa, or 37.419 kPa.
How to find the pressureThe pressure under each leg of the stool can be calculated by dividing the total force applied by the area of the legs.
First, let's calculate the total force applied by the student and the stool:
Force = Mass x Gravity
= (75.0 kg) x (9.8 m/s²)
= 735 N
The area of each leg of the stool:
Diameter = 2.50 cm
Radius = Diameter / 2
= 2.50 cm / 2
= 1.25 cm
Area = π x (Radius)²
= π x (1.25 cm)²
= 4.91 cm²
Convert the area from cm² to m²:
Area = 4.91 cm² x (1 m / 100 cm)²
= 4.91 x 10^-4 m²
The pressure under each leg:
Pressure = Force / Area
= 735 N / (4.91 x 10^-4 m²)
= 149675 Pa
The pressure under each leg of the stool is approximately 149,675 Pa, or 149.675 kPa. Since the stool has four legs, the total pressure applied by the student and the stool is divided equally among the legs, meaning each leg experiences a pressure of approximately 37,419 Pa, or 37.419 kPa.
The pressure under each leg of the stool can be calculated by dividing the total force applied by the area of the legs.
Learn more about pressure at:
https://brainly.com/question/25965960
#SPJ1
identify the correct pressure variation graph for the 1120 hz standing wave in the pipe. note that the closed end of the pipe is on the right. view available hint(s) an air-filled pipe is found to have successive harmonics at 480 hz , 800 hz , and 1120 hz . it is unknown whether harmonics below 480 hz and above 1120 hz exist in the pipe. what is the length of the pipe?
The length of the air-filled pipe is [tex]v/560[/tex] Hz, where v is speed of sound.
The correct pressure variation graph for the 1120 Hz standing wave in the pipe is the one with two antinodes and one node. The pressure is highest at the antinodes and lowest at the nodes.
To determine the length of the pipe, we can use the formula:
[tex]L = n * (v/2f)[/tex]
where L is the length of the pipe, n is the harmonic number, v is the speed of sound, and f is the frequency of the harmonic.
For the fundamental frequency (the first harmonic), we have:
[tex]L = 1 * (v/2f) = v/2f[/tex]
For the second harmonic, we have:
[tex]L = 2 * (v/2f) = v/f[/tex]
For the third harmonic (1120 Hz), we have:
[tex]L = 3 * (v/2f) = 3v/2f[/tex]
Since the pipe has harmonics at 480 Hz, 800 Hz, and 1120 Hz, we can write:
[tex]v/2L = 480 Hz,[/tex] [tex]v/L = 800 Hz[/tex], and[tex]3v/2L = 1120 Hz[/tex]
Solving for L, we get:
[tex]L = v/(2 * 480 Hz) = v/960[/tex]
[tex]L = v/800 Hz[/tex]
[tex]L = 2v/3360 Hz[/tex]
Since we do not know if there are harmonics below 480 Hz or above 1120 Hz, we cannot use these equations to solve for the length of the pipe. However, we can see that the length of the pipe is proportional to the wavelength of the sound waves in the pipe. The wavelength of the third harmonic is four times the wavelength of the first harmonic, so the length of the pipe must be four times the length of the pipe for the first harmonic. Therefore, the length of the pipe is:
[tex]L = 4 * (v/2 * 1120 Hz) = v/560 Hz[/tex]
Learn more about length here:
https://brainly.com/question/13259521
#SPJ4
The entire class goes for a hike. We all pick up rocks from the valley and carry them up to Frenchman Mountain, east of Las Vegas, where we stack them up on the peak. Subsequently, the pile collapses and all the rocks roll back down the mountain to the valley below where we originally collected them. Based on this scenario, answer the following questions:
1. Before we picked up the rocks, what energy did the rocks possess if any?
2. If the rocks were moved from point A (the valley) to point B (the peak) and subsequently rolled back down to point A, was the overall energy used zero since they ended up back where they started? Explain why or why not.
The rocks were moved to the peak by the gravitational potential energy.
Describe energy.The ability to perform tasks is referred to as energy. Kinetic energy and potential energy are the two categories of mechanical energy.1) The potential energy changes when the rocks are moved from the valley to the top.
2) The rocks were moved to the peak by the gravitational potential energy. It results from where the object is located.
3) Kinetic energy is what propels the bricks down the mountain.
4) This is thus because there is no energy at all in the gravitational field.
For more information on gravitational potential energy kindly visit to
https://brainly.com/question/19768887
#SPJ1
Complete question : The entire class goes for a hike. We all pick up rocks from the valley and carry them up to Frenchman Mountain, east of Las Vegas,
where we stack them up on the peak. Subsequently, the pile collapses and all the rocks roll back down the mountain to the valley
below where we originally collected them. Answer the following questions:
1. What energy changed by moving the position of the rocks from the valley to the peak. Explain your answer.
2. What type of energy did the work to move the rocks to the peak? Where did that energy originally come from?
3. What type of energy was used as the rocks rolled back down the mountain?
4. If the rocks were moved from point A (the valley) to point B (the peak) and subsequently rolled back down to point A was the
overall energy used zero since they ended up back where they started? Explain why or why not.
a thin circular sheet of aluminum has a radius of 20 cm and a thickness of 0.50 mm. find the mass of the sheet.
Mass of the thin circular sheet of aluminum is 0.846 kg.
Weight is the force an item exerts, mass is the amount of substance that makes up an object. The kilogramme is the SI unit of mass.
To find mass use formula for mass of a thin circular plate:
m = ρAΔt
m: plate mass ρ : density of the material, A: plate area and Δt : plate thickness
First, we need to find the area of the circular sheet, which is given by:
A =[tex]\pi r^{2}[/tex]
r: sheet radius Substituting:
A = [tex]\pi (20 cm)^2 = 1256.64 cm^2[/tex]
Convert thickness from millimeters to meters, as density is typically given in kg per cubic m.
Δt = 0.50 mm = 0.0005 m
Aluminum density is [tex]2700 kg/m^3.[/tex] Substituting:
m = ρAΔt = [tex](2700 kg/m^3)(1256.64 cm^2)(0.0005 m) = 0.846 kg[/tex]
Learn more about mass here:
https://brainly.com/question/19124779
#SPJ4
HELP PLEASE! THIS IS DUE SOON!
The statement is consistent with the Stefan- Boltzmann law
What is Stefan Boltzmann law?Stefan-Boltzmann law is a physical law that states that the total amount of radiation emitted by a blackbody per unit time and per unit surface area is proportional to the fourth power of its absolute temperature. Mathematically, the law can be expressed as:
E = σT^4
where E is the total radiant emittance, σ is the Stefan-Boltzmann constant (5.67 x 10^-8 W/m^2K^4), and T is the absolute temperature in Kelvin. The law is important in understanding the behavior of thermal radiation and plays a crucial role in many areas of science and engineering.
Learn more about Stefan Boltzmann law:https://brainly.com/question/30550607
#SPJ1
the distance from one trough to another trough is called a _____
the distance from one trough to another trough is called a wavelength.
What is wavelength?
Wavelength is a measure of the distance between consecutive peaks of a waveform. It is a fundamental physical property of all waveforms and can be used to describe the properties of light, sound, and other forms of energy. Wavelength is most often expressed in units of meters (m). Wavelengths of different types of radiation can range from extremely short distances (nanometers) to extremely long distances (kilometers). The shorter the wavelength, the higher the energy of the radiation. Wavelengths are important for determining the behavior of waveforms, such as the speed and direction of travel, the amount of energy the wave carries, and the way in which the wave interacts with other forms of matter. Wavelengths are also important in communication technologies, such as radio and television transmission.
Therefore, the distance from one trough to another trough is called a wavelength.
To learn more about wavelength
Here: https:brainly.com/question/24452579
#SPJ4
Why does an iceberg have more total internal energy than a pan of boiling water, even though the iceberg has a lower temperature? In your answer, use the words “potential,” “kinetic,” and “thermal.”
An iceberg has more total internal energy than a pan of boiling water due to its greater potential energy and the greater amount of thermal energy contained in its larger mass.
What is total internal energy?
Total internal energy is the sum of the kinetic energy of the molecules in a system and the potential energy of their interactions. It is a measure of the energy contained within a system and is typically expressed in joules.
The total internal energy of an object is the sum of its potential and kinetic energies, as well as any thermal energy it contains. Even though the temperature of an iceberg is lower than that of a pan of boiling water, an iceberg has more total internal energy for two reasons: potential energy and the amount of thermal energy. Potential energy is energy that is stored in an object due to its position relative to other objects. An iceberg floating in water is at a higher position than the water in the pan, so it has more gravitational potential energy. Thermal energy is the energy that is associated with the random motion of particles in a system. The internal energy of a system is proportional to the temperature, but it also depends on the number of particles in the system, which is referred to as its mass. Since an iceberg is much larger than a pan of boiling water, it contains more particles and therefore has more thermal energy.
Therefore, greater potential energy and the greater amount of thermal energy contained in its larger mass.
To learn more about internal energy from the link
https://brainly.com/question/11623849
#SPJ1
Which force requires contact?
Answer:
Explanation:
where is the question
Marcus wants to test the effect of gravity on objects with different masses. He drops two footballs from a first-floor window, a second-floor window, and a third-floor window. In each case, he times how long it takes the footballs to reach the ground. What is wrong with his experiment's design? (1 point)
Marcus' experiment is flawed because he is not controlling for the effects of air resistance.
Without controlling for air resistance, the time it takes for a ball to reach the ground may be affected by factors other than gravity, such as the ball's surface area, shape, and velocity. Additionally, the time measurement may be subject to human error. To design a more effective experiment, Marcus could drop the balls in a vacuum or use a wind tunnel to control for air resistance. He could also use a timer or a motion sensor to more accurately measure the time it takes for the balls to fall. Finally, he could repeat the experiment multiple times to account for any random errors or variations.To know more about gravity visit:
https://brainly.com/question/30352914
#SPJ1
The first basic step in solving force and motion problems generally involves identifying all of the forces acting on an object. This tactics box provides a step-by-step method for identifying each force in a problem. 1. Identify the object of interest. This is the object whose motion you wish to study. 2. Draw a picture of the situation. Show the object of interest and all other objects—such as ropes, springs, or surfaces-that touch it. 3. Draw a closed curve around the object. Only the object of interest is inside the curve, everything else is outside. 4. Locate every point on the boundary of this curve where other objects touch the object of interest. These are the points where contact forces are exerted on the object. 5. Name and label each contact force acting on the object. There is at least one force at each point of contact: there may be more than one.
Crate is the subject of attention. Forces are applied to the crate via rope, wood board, and earth. Below is a picture that corresponds to this query.
Although feeble, gravitational force has a very vast range. Additionally, it always looks good. Since mass is its source, it operates between any two particles of matter in the universe.
Neutrino interactions and radioactive decay are both caused by the weak forces. It has a rather small range. It is quite weak, as its name suggests. Beta-decay, or the decay of a neutron into a proton, an electron, and an antineutrino, is brought on by the weak force.
The electromagnetic force has electric and magnetic effects, such as the attraction of bar magnets or the repelling of electrical charges that are similar to one another. Despite being considerably weaker than the strong force, it has a considerable range. It only works between particles of matter carrying an electrical charge and can be either attracting or repulsive. magnetism, electricity.
Learn more about Forces here:
https://brainly.com/question/13191643
#SPJ4
the α helix and β pleated sheet are examples of which level of protein structure? a) Primary structure.
b) Tertiary structure.
c) Secondary structure.
d) Quaternary structure.
The α helix and β pleated sheet are examples of the secondary structure of protein. Hence, the correct option is (c).
The secondary structure of a protein refers to the local spatial arrangement of its amino acid residues, which are the building blocks of proteins. The α helix and β pleated sheet are two common types of secondary structure in proteins. The α helix is a right-handed helical structure that is stabilized by hydrogen bonds between the carbonyl group of one amino acid residue and the amide group of another, four residues down the polypeptide chain. The α helix structure resembles a spiral staircase, with the amino acid residues forming the steps and the hydrogen bonds forming the railings. The β pleated sheet, on the other hand, is a sheet-like structure that is stabilized by hydrogen bonds between neighboring amino acid residues in different parts of the polypeptide chain. The β pleated sheet is formed when the polypeptide chain folds back on itself, creating a sheet-like structure with the hydrogen bonds forming the edges of the sheet. The secondary structure of a protein is important because it helps to determine the overall shape of the protein, which in turn determines its function. The α helix and β pleated sheet are important secondary structures in many proteins, including enzymes, antibodies, and structural proteins.
In summary, the α helix and β pleated sheet are examples of the secondary structure of proteins, which refers to the local spatial arrangement of amino acid residues in a protein. The α helix is a right-handed helical structure, while the β pleated sheet is a sheet-like structure. The secondary structure of a protein is important for determining its overall shape and function.
To know more about protein please refer: https://brainly.com/question/14652022
#SPJ4
A balloon is inflated to a pressure of 0.2 bar. A 5.0 kg book is balanced on top of the
balloon. With what surface area does the balloon contact the book? (Hint: Remember that
1 bar = 100 000 Pa.)
Answer: THE ANSWER IS 0.0555
Explanation:
BECAUSE A^2 + B^2 + C^2 IS THE ANSWER TO THE HYPOTENUSE OF THE PA 100000
suppose we are in the middle of a slowly melting block of ice. as we add a little more thermal energy, what happens to the temperature of the ice?
Adding more thermal energy to a slowly melting block of ice will cause the temperature of the ice to remain constant until it has completely melted. Once the ice has completely melted, the temperature of the liquid water will start to rise.
As we add a little more thermal energy to a slowly melting block of ice, the temperature of the ice will remain constant at 0°C until all of the ice has melted. This is because the added thermal energy is being used to break the bonds between the water molecules in the ice, causing it to change from a solid to a liquid.
Once all of the ice has melted, any additional thermal energy will cause the temperature of the water to increase. This process is known as latent heat of fusion, which is the amount of energy required to change a substance from a solid to a liquid at a constant temperature.
Learn more about thermal energy at https://brainly.com/question/19666326
#SPJ11
What is the name for a burst of activity on an EEG in the early stages of sleep?
gamma waves
sleep spindles
REM
lingering activation
The name for a burst of activity on an EEG in the early stages of sleep is "sleep spindle".
What is sleep spindle?A burst of brain activity during non-rapid eye movement (NREM) sleep is known as a sleep spindle and can be seen on an electroencephalogram (EEG). Although it can occur in other NREM sleep stages as well, it is a hallmark of Stage 2 sleep.
Sleep spindles are characterized by a burst of rhythmic brain activity that spans from 11 to 16 Hz and are short (often lasting only a few seconds). The thalamus, a region of the brain that is essential for transmitting sensory data to the cerebral cortex, is the source of this activity. The thalamus absorbs sensory input during sleep and modifies the information flow to the cortex, enabling the brain to filter out unimportant inputs and concentrate on significant ones.
To know more about sleep spindle visit:
brainly.com/question/13031857
#SPJ4
On which type of hillside is water erosion most likely to occur?
As a result, in the hilly area where it is hot and it rains frequently, water erosion is more likely to affect the landforms there.
It rains frequently where it is warm, rainy, and humid because evaporation and cloud formation occur at a much faster pace in these conditions.
Landforms are directly impacted by this, particularly in steep areas. It's because one of the things that causes the rocks to weather and erode in this area is the water. While erosion refers to the movement of the rock fragments, weathering refers to the breakdown of the rocks.
When water is moving, the rock minerals dissolve. Compared to hard rocks, soft rocks erode more easily. Additionally, quickly worn and eroded are the carbonate rocks. As a result, the geography of the region is altered.
To learn more about water erosion visit;
https://brainly.com/question/3852201
#SPJ4
if two points are at the same potential, does this mean that no net work is done in moving a test charge from one point to the other? does this imply that no force must be exerted? explain.
a spaceship has a rest mass of 620,000 tons. if you could measure its mass when it was traveling at half the speed of light, what would the value be?
The rest mass of a spacecraft is 620,000 tons. Its mass would be 715,088.8 tons if you could measure it when it was moving at half the speed of light.
The mass of a moving object is given by the relativistic mass formula:
[tex]m = m_0 / \sqrt{(1 - v^2/c^2)}[/tex]
here,
m₀ is rest mass of the object,
v is velocity, and
c is speed of light.
In this case, the rest mass of the spaceship is m₀ = 620,000 tons. If it is traveling at half the speed of light, its velocity is v = 0.5c, where c is approximately 299,792,458 m/s.
Reserving the values:-
[tex]m = m_0 / \sqrt{(1 - v^2/c^2)}[/tex]
= [tex]620,000 tons / \sqrt{(1 - (0.5c)^2/c^2)}[/tex]
=[tex]620,000 tons / \sqrt{(1 - 0.25)}[/tex]
= [tex]620,000 tons / \sqrt{(0.75)}[/tex]
= 620,000 tons / 0.866
= 715,088.8 tons
Therefore, the mass of the spaceship when it is traveling at half the speed of light is approximately 715,088.8 tons. Note that the relativistic mass of an object increases as its velocity approaches the speed of light. At speeds much smaller than the speed of light, the relativistic mass is approximately equal to the rest mass.
To know more about mass please refer: https://brainly.com/question/29038134
#SPJ4
how does the application of cool pads and spraying of water on the skin lower the body temperature?
Application of cool pads and spraying of water on the skin lowers the body temperature by increasing the rate of evaporation.
How does the application of cool pads and spraying of water on skin lower body temperature?Application of cold water to the skin can be achieved by either sponging patient or using spray bottle. Placing fan to blow directly on patient while also spraying or sponging will increase rate of evaporation, and therefore will more rapidly decrease body temperature
Spraying water on your body helps cool it off because of evaporative cooling. Turning liquid from its liquid state into a gas requires energy. This energy is taken from our body in the form of heat and the resulting heat transfer leads to desired cooling effect.
To know more about body temperature, refer
https://brainly.com/question/14758813
#SPJ1
oppositely charged parallel plates are separated by 5.16 mm. a potential difference of 600 v exists between the plates. (a) what is the magnitude of the electric field between the plates?
The magnitude of the electric field between the plates is 116279 N/C. A parallel-plate capacitor is a device that stores electric charge and electric potential energy.
The electric field between the plates of a parallel-plate capacitor is given by:
E = V/d
where E is the electric field (in N/C), V is the potential difference (in volts), and d is the distance between the plates (in meters).
In this problem, we are given V = 600 V and d = 5.16 mm = 0.00516 m. Substituting these values into the equation, we get:
E = V/d
E = 600 V / 0.00516 m
E = 116279 N/C
Therefore, the magnitude of the electric field between the plates is 116279 N/C
A parallel-plate capacitor is a device that stores electric charge and electric potential energy. It consists of two conducting plates separated by a small distance, with the space between the plates filled with an insulating material (called a dielectric).
In this problem, we were given the potential difference and the distance between the plates, and we used the formula for the electric field to calculate its magnitude. The electric field is a fundamental concept in electromagnetism, and it plays an important role in a wide range of phenomena, from the behavior of charged particles to the operation of electronic devices.
Learn more about dielectric here:
https://brainly.com/question/30523009
#SPJ4
How does the energy of visible light compare to the energy of infrared radiation?
The energy of visible light is more as compared to the energy of infrared radiation
Does infrared radiation exceed visible light in intensity?
Accordingly, the frequencies of IR, which range from around 300 Ghz to 400 THz, are greater than those of microwaves but lower than those of visible light. Although longer infrared waves can be felt as heat, infrared light is invisible to the human eye.
Due to their longer wavelengths than visible light, infrared waves can travel across crowded areas of gas and dust in space without being significantly scattered or absorbed. As a result, employing optical telescopes, infrared energy can also show celestial objects that are invisible to the eye.
To learn more about infrared use :
https://brainly.com/question/29796311
#SPJ1
a). Show that the average speed of Leslie is 10 km/h when she runs to the store 5 km away in 30 min.
(b) How fast is this in m/s?
6. (a) Calculate the acceleration for a ball that starts from rest and rolls down a ramp and gains a speed of 30 m/s in 4 s.
(b) What would acceleration be if the ball rolls at 60 m/s?
Acceleration is a physical quantity that describes the rate of change in velocity of an object over time. It is a vector quantity, which means it has both magnitude and direction, and is measured in units of meters per second squared (m/s²).
Describe Acceleration
When an object is accelerating, its velocity is changing, either by increasing or decreasing in speed or changing direction. The magnitude of the acceleration depends on the force applied to the object, which can come from a variety of sources such as gravity, friction, or electromagnetism.
The formula for acceleration is:
a = (v2 - v1) / t
where a is the acceleration, v2 is the final velocity, v1 is the initial velocity, and t is the time it takes to go from v1 to v2.
If an object is moving in a straight line with a constant acceleration, its velocity can be calculated by the following equation:
v = v0 + at
where v is the final velocity, v0 is the initial velocity, a is the acceleration, and t is the time.
Acceleration is a fundamental concept in physics and is used to describe the motion of objects in a wide variety of situations, including free-fall, projectile motion, circular motion, and the behavior of fluids. It is also essential in engineering and design, where it is used to calculate the performance and efficiency of machines and vehicles.
(a) To find the average speed of Leslie, we can use the formula:
average speed = total distance / total time
Leslie runs to the store 5 km away in 30 minutes (0.5 hours), so the total distance is 5 km and the total time is 0.5 hours.
average speed = 5 km / 0.5 hours = 10 km/h
Therefore, the average speed of Leslie is 10 km/h when she runs to the store 5 km away in 30 minutes.
(b) To convert km/h to m/s, we can use the conversion factor:
1 km/h = 0.2778 m/s
So, the speed of Leslie in m/s is:
10 km/h × 0.2778 m/s/km/h = 2.78 m/s
Therefore, Leslie's speed is 2.78 m/s.
(a) To calculate the acceleration of the ball, we can use the formula:
acceleration = (final velocity - initial velocity) / time
The ball starts from rest, so the initial velocity is 0 m/s. After 4 seconds, it gains a speed of 30 m/s.
acceleration = (30 m/s - 0 m/s) / 4 s = 7.5 m/s²
Therefore, the acceleration of the ball is 7.5 m/s².
(b) If the ball rolls at 60 m/s, we can use the same formula to find the acceleration:
acceleration = (60 m/s - 0 m/s) / 4 s = 15 m/s²
Therefore, the acceleration of the ball would be 15 m/s² if it rolls at 60 m/s.
To know more about speed visit:
brainly.com/question/13263542
#SPJ1
I need help in this please
The net electric force on charge +q is along direction C.
option C.
What is the electric force between two charges?
The electric force between two charges is determined applying Coulomb's law of electrostatic force.
Mathematically, the formula for this law is given as;
F = kq₁q₂/r²
where;
k is the Coulomb's constantq₁ is the magnitude of charge 1q₂ is the magnitude of charge 2r is the distance between the chargesThe strength of the electric force increases with decrease in the distance between the two charged particles.
The distance between the charge at the center and
point C = 1.5 dpoint B = 2dpoint D = point A = √[ (1.5d)² + (2d)² ] = 2.5dThe electric force is strongest towards point C, so the direction of the force will be towards point C.
Learn more about electric force here: https://brainly.com/question/17692887
#SPJ1
three massive spheres are connected to a rod of very small mass. consider the moment of inertia of the system, first when it is rotated about sphere a, and then when rotated around sphere b. are the moments of inertia the same or different? justify your answer.
To calculate the moments of inertia of the system, we would need to know the masses and positions of the spheres relative to the axis of rotation.
The moment of inertia of an object is a measure of its resistance to rotational motion. It depends on both the mass and the distribution of mass within the object. When a system of spheres connected by a rod is rotated about one of the spheres, the distribution of mass in the system will be different compared to when it is rotated about a different sphere.
To determine whether the moments of inertia of the system when rotated about sphere a and sphere b are the same or different, we need to consider the distribution of mass in each case. If the system is symmetric about both spheres, then the moments of inertia will be the same. However, if the distribution of mass is different, then the moments of inertia will be different.
Learn more about rotational motion :
https://brainly.com/question/12995374
#SPJ4
two forces are acting on an object. one force is 6 n forward. the other force is 8 n backward. what is the net force acting on the object?
Answer:
2 N backward
Explanation:
Positive direction is forward.
Fnet = 6 N - 8 N = -2 N
Negative sign in the result means the net force is 2 N backward
A pipet is used to measure out 10 mL of water. If the mass of this volume of water is 9.990 g and the density of water is given as 0.9978 g/mL, what is the actual volume of water measured out? O 10.000 mL O 9.990 mL O The actual volume measured out is impossible to tell O 10.012 mL
10.012ml is the actual volume of water measured out.
What does the word "volume" mean?
Each thing in three dimensions takes up some space. The volume of this area is what is being measured. The space occupied within an object's borders in three dimensions is referred to as its volume. It is sometimes referred to as the object's capacity.
The measure of how densely a material is packed together is called density. As the mass per unit volume, it has that definition. Typically, there are two forms of density: absolute density and relative density. The ratio of a substance's density to the density of a reference material is known as its relative density, sometimes referred to as specific gravity. Water is frequently used as the reference material.
D ⇒ M/V
V ⇒ M/D
M ⇒ 9.990g
D⇒ 0.9978g/ml
V ⇒ 9.990/0.9978 ⇒ 10.012ml
To learn more about volume use:
https://brainly.com/question/14197390
#SPJ1
and a student measures the length of a 1.00 m standard bar. he obtains measurements of 0.80 m, 0.78 m, and 0.79 m. which describes his measurements?
The length of the 1.00 m standard bar was measured by the student, and the results show approximate but correct readings.
In measurements, precision refers to the consistency and reproducibility of the measured values whereas accuracy refers to how closely the measured values resemble the true or accepted value.
With a 1.00 m standard bar, the student in this instance measured 0.80 m, 0.78 m, and 0.79 m. Since the measurements' range is 0.02 m (0.80 m - 0.78 m), which is disproportionately large given the amount of the measured quantity, they are not exact. Yet, the measurements are precise since they are near to the actual value of 1.00 m.
Learn more about quantity here :
https://brainly.com/question/12986460
#SPJ4
In the above figure, what is the net electric potential at point P due to the four particles if V=0 at infinity, q=5.00 fC and d=4.00 cm?
The net electric potential at point P due to the four particles would be Vtotal=5.5625×10−4Nm/C.
Among electric potential and electric field which one is a vector quantity?Electric field is a vector quantity, while electric potential is a scalar quantity. So, in order to find the electric potential on a point due to several other point charges, we will make a sum of their individual electric potential with respect to the point charge. So, to find the electric potential on point P due to the other point charges, we can find the electric potential of each point charge on P and add them, V=V1+V2+V3+V4
The electric potential of charges at either side of point P on P will be given by,
V1=V2=k(+q)d
In the same way, the electric potential on point P, due to the third charge,
V3=k(−q)2d
And the electric potential on point P due to fourth charge will be,
V4=k(−q)d
We know that electric potential is a scalar quantity, thus the total electric potential on point P is simply the sum of all the electric potentials on point P, V=V1+V2+V3+V4
Vtotal=k(+q)/d+k(+q)/d+k(−q)/2d+k(−q)/d
Vtotal=kq[(+1)/d+(+1)/d+(−1)/2d+(−1)/d]
Substituting the value of k=1/4πε0
and solving,
Vtotal= [ (2+2−1−2)/2d]
Vtotal= [(1)/2d]
We also know that the q=5.00fC=5×10⁻¹⁵C
, d=4.00cm=4×10⁻²m
and the value of the electrostatic constant, k=1/4πε0=8.996×10⁹Nm2C−2
Vtotal=8.996×10⁹Nm2C−2×5×10⁻¹⁵C[(1)2×4×10⁻²m]
Solving for Vtotal
we get,
Vtotal=5.5625×10⁻⁴Nm/C.
To know more about Electric field, visit:
brainly.com/question/30544719
#SPJ1
if the steel ball is shot horizontally off the table, how much time would it take the ball to hit the ground for each of the velocity settings of the launcher?
The time for a steel ball to hit the ground when shot horizontally off a table is independent of the initial velocity, and the formula is [tex]d = v_i*t + (1/2)at^2[/tex].
To decide the time it takes for a steel ball to stir things up around town when shot evenly off a table, we can utilize the conditions of movement, explicitly the kinematic condition:
[tex]d = v_i*t + (1/2)at^2[/tex]
where:
d is the distance voyaged
v_i is the underlying speed
an is the speed increase
t is the time
We can expect that the speed increase is because of gravity, which is steady and equivalent to [tex]9.81 m/s^2.[/tex]
Since the ball is shot on a level plane, its underlying vertical speed is zero. Accordingly, we can work on the situation to:
[tex]d = (1/2)at^2[/tex]
Settling for t, we get:
t = sqrt(2*d/a)
To decide the distance voyaged, we can utilize the way that the ball will follow an explanatory direction and will stir things up around town simultaneously it would have taken to fall upward from a similar level. Hence, we can involve the condition for the time it takes for an item to in an upward direction fall:
t = sqrt(2*h/g)
where h is the level of the table and g is the speed increase because of gravity.
Utilizing the trial information, we can decide the level of the table and the distance the ball goes prior to stirring things up around town for every speed setting of the launcher. Then, we can work out the time it takes for the ball to stir things up around town involving the condition for t.
The time it takes for the ball to stir things up around town will be the equivalent no matter what the speed setting of the launcher, as long as the ball is shot evenly with a similar starting level. This is on the grounds that the underlying speed in the level bearing doesn't influence the time it takes for the ball to upward fall.
This outcome is steady with the way that the time it takes for an item to fall upward just relies upon the level and speed increase because of gravity. Hence, failing upward from the table top to the floor beneath would bring about a similar time it takes for the ball to raise a ruckus around town when shot evenly off the table.
To learn more about kinematics, refer:
https://brainly.com/question/15375616
#SPJ4
The complete question is:
If the steel ball is shot horizontally off the table, how much time would it take the ball to hit the ground for each of the velocity settings of the launcher? Explain your answer using the equations of motion and your experimental data. How does this relate to the ball being dropped vertically from the table top to the floor below.
29) electrons in an x-ray machine are accelerated from rest trhough a potential difference of 50 kv. what is the kinetic energy of the electrons en ev?
Potential difference difference V = 50,000V
Kinetic Energy K.E. = q v , for electron q=E
KE= 50,000 ev.
What is kinetic energy?The energy an object has as a result of motion is known as kinetic energy in physics. It is described as the effort required to move a mass-determined body from rest to the indicated velocity. The body holds onto the kinetic energy it acquired during its acceleration until its speed changes. The body exerts the same amount of effort when slowing down from its current pace to a condition of rest. Formally, a kinetic energy is any term that includes a derivative with respect to time in the Lagrangian of a system.Gottfried Leibniz and Johann Bernoulli were the first to formulate the classical mechanics principle that E mv2, referring to kinetic energy as the "vital power," or vis viva. Experimental proof of this connection was supplied by Willem's Gravesande in the Netherlands. Willem's Gravesande discovered that the penetration depth of weights was proportional to the square of their impact speed by dropping weights from various heights upon a piece of clay.
To know more about Kinetic energy visit:
https://brainly.com/question/15764612
#SPJ1
