the ____ grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning

Answers

Answer 1

Answer:

the jig grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning


Related Questions


What is the first test you should do when checking the charging system?

Answers

Answer:

Connect the test light in series with the negative post, and start pulling feed wires. The first to check is the heavy charging wire from the alternator. A bad or leaky diode in an alternator is a very common source of overnight battery drain. Connect wires one at a time to see what lead is drawing current.

The local interlock system on a hybrid vehicle detects when ________ have been removed from high-voltage circuits.

Answers

The local interlock system on a hybrid vehicle detects when covers have been removed from high-voltage circuits.

What is a hybrid vehicle?

A hybrid vehicle can be defined as a mechanical system that is designed and developed to use multiple sources of power such as fuel and batteries, so as to enable it move from one point to another.

By design, the local interlock system on a hybrid vehicle is designed and developed to detect when covers have been removed from high-voltage circuits.

Read more on hybrid vehicle here: https://brainly.com/question/3535024

#SPJ1

Technician A uses heat shrink tubing to insulate and seal soldered wire connections. Technician B wraps the soldered connection with electrical tape. Who is correct

Answers

The technician that's correct is Technician A.

Who is a technician?

A technician is an individual that's employed to look after the technical equipments in an organization.

In this case, Technician A uses heat shrink tubing to insulate and seal soldered wire connections. He is correct.

Learn more about technicians on:

brainly.com/question/1548867

#SPJ12

Check the level of motor oil in your engine by ?

Answers

Answer:

cpct gvxjjxjhdfjokjdzfjiyddzzsjhxf

If the digital inputs for a supply-air fan control application indicate that the supply-air fan should be on, the controller compares the measured ________ to the set point; if this reading is lower than the setpoint, the supply-air fan speed must be increased.

Answers

If the digital inputs for a supply-air fan control application show that the supply-air fan should be ON, the controller compares the measured static air pressure to the set point.

The operation of a supply-air fan control.

Basically, the controller of a supply-air fan control application is designed and developed to compare the measured static air pressure to the set point when its digital inputs indicate that the supply-air fan should be ON.

By design and configuration, if the measurement of the static air pressure is lower than the set point, the supply-air fan speed must be increased by an engineer accordingly.

Read more on supply-air fan here: https://brainly.com/question/15096367

#SPJ12

The A/C compressor will not engage when the A/C is turned on. The static refrigerant pressure is 75 psi and the outside temperature is 72 degrees F. Technician A says that a poor connection at the pressure cycling switch could be the cause. Technician B says that a faulty A/C clutch coil could be the cause. Who is correct

Answers

In the case above,  poor connection at the pressure cycling switch  and also a faulty A/C clutch coil could be the cause.

What is likely the reason when an A/C compressor will not engage if A/C is turned on?

The cause that hinders the A/C Compressor from engaging are:

Due to low pressure lockout.Due to a poor groundDue to bad clutch coil.Dur to an opening in the wire that links to the clutch coil.Due to a blown fuse.

Note that the pressure switches is known to be one that control the on/off function of any kind of AC compressor and as such, if there is switch failure, it can hinder the AC compressor from functioning at all.

Therefore, technician A and B are correct.

Learn more about refrigerant pressure from

https://brainly.com/question/10054719

#SPJ1

Where a solid wood door is installed as a permitted opening between a garage and a residence, the minimum thickness of the door shallbe __________ inches.

Answers

For a garage and a residence, the minimum thickness of a solid wood door that is installed as a permitted opening shall be 1 3/8 inches.

What is a door?

A door can be defined as a solid material made of wood or metal, which is designed and developed to facilitate entrance and exit out of a building.

According to the International Residential Code (IRC), the minimum thickness of a solid wood door that is installed as a permitted opening for a garage and a residence shall be 1 3/8 inches.

Read more on doors here: https://brainly.com/question/22731237

#SPJ12

Besides hev and ev motor systems themselves what other systems may use high voltage

Answers

Besides hev and ev motor systems themselves what other systems may use high voltage are the air conditioning compressor, auxiliary battery, and water pump.

Why an excessive voltage is used?

High voltages are utilized in transmission structures due to the fact a better voltage implies a decrease modern-day for a given energy of transmission. With a decrease modern-day, much less warmth is generated withinside the transmission traces and so much less electricity is wasted. Furthermore, it has superb environmental benefits.

To come up with a difficult estimate the common rated energy of the water pump is from 250 watts to 1500 watts. The smaller the water pump, much less is the wattage, much less is the energy consumption, subsequently low is the release and head.Usually, an auxiliary deliver is energy delivery that gives an auxiliary voltage. An instance will clean this up. Say you've got got a switching circuit with score of 220VAC enter and 12VDC output. Enclosure air conditioners may be designed to run on AC and DC voltages. The AC versions perform at 120, 230, 380, 400, 480, 575 and six hundred V at frequencies of 60 and/or 50 Hz.

Read more about the voltage:

https://brainly.com/question/1176850

#SPJ1

3. You were given the opportunity to be a project manager for Apple to work on a new product. Provide me with details on what that product is ( you make it up ), how will you approach the work and find resources for it.

Answers

You were given the opportunity to be a project manager for Apple to work on a new product by Product control examples additionally consist of the branding and consumer conversation.

What makes you a very good mission supervisor?

Good mission managers recognize and recognize their marketplace and the enterprise in their projects. They look at the opposition and compare alternatives. A desirable mission supervisor remains updated at the brand new developments withinside the enterprise in their mission, and they show off a stable knowledge and know-how in their enterprise.

Product control examples additionally consist of the branding and consumer conversation required to release a brand new product. Each product, in its nascent form, calls for right branding. This creates recognition approximately the product withinside the marketplace. Advertising and PR managing additionally fall beneath neath the umbrella of product control.

Read more about the manager:

https://brainly.com/question/24553900

#SPJ1

Tech A says that on the full floating axle, there are two tapered roller bearings between the hub and the outside of the axle housing. Tech B says that a semi-floating axle, the axle supports the weight of the vehicle and is also subject to bending forces as the vehicle corners. Who is correct

Answers

The information depicted shows that both technicians are correct.

Who is a technician?

This is an individual who overlooks the technical equipment in an organization.

In this case, on the full floating axle, there are two tapered roller bearings between the hub and the outside of the axle housing.

Also in a semi-floating axle, the axle supports the weight of the vehicle and is also subject to bending forces as the vehicle corners.

Therefore, they're both correct.

Learn more about technicians on:

brainly.com/question/1548867

#SPJ12

Tech A says that if a CV boot is torn, it can typically be replaced without replacing the entire joint or shaft. Tech B says that worn CV joints can make a clicking noise when driving while making a tight turn. Who is correct

Answers

Both Technician A and Technician B are correct based on the information provided.

When to replace a CV boot?

The CV boot on an automobile vehicle should be replaced when it is torn but shouldn't have been torn for too long. Thus, you should just replace the boot when the CV joint is not yet completely damaged or full of dirt.

Similarly, worn CV joints in an automobile vehicle can make a clicking noise when driving while making a tight turn on a road.

Read more on CV joints here: https://brainly.com/question/12239770

#SPJ12


Design a driver circuit that should drive a a seven segment to display octal numbers
[0 up to 7]. Your work should include the following steps
1) An appropriate title
2) The truth Table
3) Simplified expressions for the appropriate circuit
4) Logical circuit for the driver.​

Answers

Answer:

point hehe sorry sorry

Explanation:

I don't know

Directions: Correct the errors.
to
1. I went to the library for study last night.
2. Helen borrowed my dictionary for to look up the spelling of "occurred."
3. The teacher opened the window for letting some fresh air in the room.
4. I came to this school for learn English.
5. I traveled to Osaka for to visit my sister.

Answers

Answer:

1. I went to the library to study last night.

2.Helen borrowed my dictionary to look up the spelling of "occurred."

3.The teacher opened the window to let some fresh air into the room.

4..I came to this school to learn English.

5.I traveled to Osaka to visit my sister.

Explanation:

...

A feature control frame must be connected to

Answers

Answer:

Surface Parallelism When a surface is to be parallel to a datum plane, the feature control frame is connected by a leader to the surface, or to an extension line from the surface.

Explanation:

Before installing head gaskets look for “____” labels on the head gaskets

Answers

Before installing head gaskets, you should look for "this side up" or "front" labels on the head gaskets.

What is a head gasket?

A head gasket can be defined as a gasket which is fitted between the engine block and the cylinder head in an internal combustion engine, so as to seal oil passages and absorb the pressures of the combustion that occurs inside the engine.

As a general rule, you should look for "this side up" or "front" labels on the head gaskets before installing head gaskets in an internal combustion engine of a vehicle.

Read more on head gaskets here: https://brainly.com/question/1264437

#SPJ1

valocity and acceleration of spherical coordinates and polar coordinates with complete description and derivations?​

Answers

A point P at a time-varying position (r,θ,ϕ) ( r , θ , ϕ ) has position vector ⃗r , velocity ⃗v=˙⃗r v → = r → ˙ , and acceleration ⃗a=¨⃗r a → = r → ¨ given by the following expressions in spherical components.

An Exterior Insulation Finish System (EIFS) shall terminate a minimum ___________ inches above the finished ground level.

Answers

Answer:

An Exterior Insulation Finish System (EIFS) shall terminate a minimum 6 inches above the finished ground level.

Please show NEC article 310.10(H)

Answers

Conductors in Parallel is covered in 310.10(H). Often when working with higher ampacities, we find it to be cumbersome and expensive to keep increasing the size of the wire and conduit. The solution is often to use multiple runs that are connected to a common location on each end. Notice in the 2011 edition of the code that much of this section is highlighted gray, indicating new or revised text. The change here was that the previous code stated that you were permitted to parallel conductors 1/0 AWG and larger; however, it didn’t specifically prohibit you from paralleling smaller conductors, which was the intent and the way it was enforced in all my years of enforcement. However, that’s not what the actual language said, and ambiguous language cancause enforcement issues; therefore, in the 2011 code it was made clear that you are only allowed to parallel conductors 1/0 AWG and larger.

The following is a dump of a udp header in hexadecimal format. 0632000d 001ce217 a. what is the source port number? b. what is the destination port number? c. what is the total length of the user datagram? d. what is the length of the data? e. is the packet directed from a client to a server or vice versa? f. what is the client process?

Answers

The source port number of the dump given above is 1586. The destination port number is given below.

What is the destination port number?

The destination port number is given as 000DH = 13. Destination port number is determined by running the following command in the Command Prompt: netstat-a

Then you hit the enter button.

What is the total length of the user datagram?

The total length of the datagram is given as 001CH = 28 bytes. Datagram is a form of message that is self-contained, that is relayed over the network. It must be noted that it's content cannot be guaranteed.

What is the length of the data?

The length of the data is 20 bytes. This is arrived at by computing the following:

Data Lenght - Header

= 28 - 8

= 20bytes.

Is the packet directed from a client to a server or vice versa?

It is to be noted that the packet is directed from the client to the sever.

Learn more about ports at;
https://brainly.com/question/18133590
#SPJ1

when electric power is transmitted over long distance, line losses can be reduced by generating AC rather than DC voltage and by transmitting?

Answers

When electric power is transferred over a long distance then, line loss can be reduced by high voltage and low current. Thus, option A is correct.

What is electric power?

The complete question is attached to the image below.

The electric circuit transfers the electric current then it is called electric power. The loss in the line over a larger distance is reduced by transferring AC instead of DC voltage.

The AC transmitted is of high voltage, and the power is low. The equation for current is given,

P = VI

The increase in the voltage causes the decrease in the current and in turn the resistance also reduces resulting in the loss of the power of the circuit to decrease.

Therefore, the loss is reduced by transferring high voltage and, low current AC.

Learn more about high volatge AC here:

https://brainly.com/question/18069892

#SPJ1

When what is visible to end-users is a deviation from the specific or expected behavior, this is called:

Answers

When what is visible to end-users is a deviation from the specific or expected behavior, it's an error.

What is an error?

It should be noted that an error means a deviation from what's expected by an individual or programmer.

In this case, when what is visible to end-users is a deviation from the specific or expected behavior, it's an error. This is a deviation.

Learn more about error on:

brainly.com/question/16012410

#SPJ12

How many gyros and how many accelerometers are in the INS?

Answers

The number of gyros and accelerometers that are in the INS are three (3) gyros and two (2) accelerometers respectively.

What is INS?

INS is abbreviation for Inertial Navigation System and it can be defined as a navigation device that is designed and developed to use motion sensors, a computer, and rotation sensors, so as to continuously calculate by dead reckoning the velocity, position, and orientation of a moving object.

Based on scientific information and records, the number of gyros and accelerometers that are in the INS are three (3) gyros and two (2) accelerometers respectively.

Read more on Inertial Navigation System here: https://brainly.com/question/26052911

#SPJ12

Why can’t we find all errors before we give the software to our customers?

Answers

Explanation:

what is protozoa define it with diagram srt-nhev-mvp

i m n * de

Draw isometric projection of a pls help

Answers

Draw isometric projection Spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn the same.

What is isometric projection?

Definition of isometric projection an axonometric projection wherein the 3 spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn same.

An isometric view of an item may be received via way of means of selecting the viewing path such that the angles among the projections of the x, y, and z axes are all of the same, or 120°. For example, with a cube, that is achieved via way of means of first searching immediately toward one face.

Read  more about the data:

https://brainly.com/question/25749514

#SPJ1

Which thematic group is involved in the transmission and generation of electrical power?
a.Communication Systems
b.Control Systems
c.Computer Systems
d.Energy Systems
e.Electronic Systems

Answers

In the transmission and generation of electrical power would have to be D. Energy systems!

Answer:

The 17 distinct years Mariah Carey has topped Billboard's Hot 100, spanning an historic four consecutive decades:

1990

1991

1992

1993

1994

1995

1996

1997

1998

1999

2000

2005

2006

2008

2019

2020

2021

Technician A says that mechanical shifting controls can wear out over time. Technician B says that vacuum control rubber diaphragms can deteriorate over time. Who is correct

Answers

Based on the information, both technician A and technician B are correct.

How to depict the information?

From the information given, Technician A says that mechanical shifting controls can wear out over time.

Technician B says that vacuum control rubber diaphragms can deteriorate over time.

In this case, both technicians are correct as the information depicted is true.

Learn more about technicians on:

brainly.com/question/1548867

#SPJ12

4.5% complete Question Select the methods of containment based on the concept of isolation. (Select all that apply.) A.Blackhole B.Sinkhole C.Physical disconnection/air gapping D.Sandboxing

Answers

Answer:

A. Blackhole

C. Physical disconnection/air gapping

D. Sandboxing

Here are the methods of containment based on the concept of isolation:

Physical disconnection/air gapping is the most effective method of isolation, separating the infected system from the rest of the network.

How does sandoxing work?

Sandboxing isolates the infected system in a controlled environment, allowing analysis and cleaning without affecting the rest of the network. Quarantine isolates the infected system from the rest of the network until it can be cleaned, preventing it from infecting other systems.

The following methods are not based on the concept of isolation:

Blackhole: This is a method of redirecting malicious traffic to a dead end. This does not isolate the infected system, but it does prevent the malicious traffic from reaching other systems on the network.

Sinkhole: This is a method of redirecting malicious traffic to a honeypot. This does not isolate the infected system, but it does allow security researchers to collect information about the malicious traffic.

Therefore, the methods of containment based on the concept of isolation are Physical disconnection/air gapping, Sandboxing, and Quarantine.

Read more about Quarantine here:

https://brainly.com/question/1597166

#SPJ2

an incorrect way of handling disposable gloves includes

Answers

The incorrect way of handling disposable gloves are as follows;

Blow into themHold them by the fingersRoll them onto the hands

What are disposable gloves?

Disposable gloves are gloves that you use one time and then throw away.

They are usually transparent and made of nitrile, latex, or vinyl.

They are usually tough to withstand liquids and chemicals.

Therefore, the incorrect way of handling them includes the following;

Blow into themHold them by the fingersRoll them onto the hands

learn more on disposable gloves here: https://brainly.com/question/24012826

#SPJ11

he minimum number of branch circuits is determined from ____ load and the size (or rating) of the circuits used.

Answers

The minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.

What is circuit?

It should be noted that circuit means a complete circular path that electricity flows through.

In this case, the minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.

Learn more about circuit on:

brainly.com/question/2969220

#SPJ12

In a basketball game, the point guard A intends to
throw a pass to the shooting guard B, who is breaking
toward the basket at a constant speed of 12 ft /sec. If
the shooting guard is to catch the ball at a height
of 7 ft at C while in full stride to execute a layup,
determine the speed v0 and launch angle with
which the point guard should throw the ball

Answers

In a basketball game, point guard A intends the speed as 47.76 ft/sec, and the launch angle will be 41.084°.

What is the projectile motion?

The projectile motion is given as the motion of the object in the curved path near the earth's surface. The throwing of the ball will follow the projectile motion.

The missing image is attached below.

The given game situation consists of:

Velocity of shooting guard (vs) = 12 ft/sec.

Distance from B to C (sc) = 20 ft

Final height to catch the ball, 7 ft

The total distance to cover from B to C = 60 ft

Time is taken to reach B to C = Distance/Speed

Time to reach B to C = 20ft/12ft/sec

Time to reach B to C = 1.667 sec.

The time taken to cover the horizontal distance:

Distance = Velocity * Time

60³ = v₀cosθ * distance/time

60³ =  v₀cosθ * 20/12

v₀cosθ  = 36 ft/sec

The vertical movement can be given where, g = 32.2 ft/sec²:

s = s₀ + v₀sinθ * time + 1/2 -g time²

7 = s + v₀sinθ * 20/12 - 1/2 32.2 ft/sec² * (20/12)²

v₀sinθ = 31.3875 ft/sec

[tex]\rm v_0 =\sqrt{v_0sin\theta^2\;+\;v_ocos\theta^2}[/tex]

Substituting the values:

v₀ = 47.76 ft/sec

The launch angle for the ball will be:

tanθ = v₀sinθ/v₀cosθ

tanθ = 31.3875/36

tanθ = 0.871

θ = 41.084°

Thus, the speed v₀ of the ball will be 47.76 ft/sec, and the launch angle will be 41.084°.

Read more about projectile motion, here:

https://brainly.com/question/11049671

#SPJ1

Other Questions
simplify -9 2/7-(-10 3/7) a sign at the summit of a mountain pass says that the grade for the next 5 miles of straight driving is 4.2 degrees. Determine the change of elevation in feet for a car at the end of the 5 mile drive Windows, mac os, and which other operating system constitute three desktop operating systems?. Solve the following compound inequality: (1 point)-2(x+8) +6 > x-4 or -3x + 12 < 6(x-4)0x4Ox>2 orx-2 orx Choose the quadratic model for the situation.d(v) =2.14v^/.039d(v) =2.15v^/64.79d(v) =2.15v^/25.116 If anyone can help me to solve this. The Green Party is in favor of protections for the environment and social justice. Which of the following best explains why theGreen Party has not won congressional seats or the presidency?Select one:a. The Constitution provides for the election of third parties to Congress, but not the presidencyb. Their views have been assimilated into one of the major political parties, so people who align with their beliefs tend to vote for the major partyc. Most Americans do not agree with environmental protection or social justiced. They are a third party and are not able to receive as many dollars in campaign finance as the two major parties When water vapor cools, it condenses.Which number represents this process on the hydrologic cyclediagram?O 102O 304 please place the dot for me(20 points will give brainliest!!!) 3 is less than w and 9 is greater than w cos2pi/7+cos4pi/7+cos8pi/7=1/8 Which transform function would you use to operate the filename values into two separate columns, one for the filename and the other for the file extension? e. G. , xml Like people differentiated by race, religion, or sexual orientation, the elderly constitute a ______ group that may be subject to negative stereotypes and discrimination. What was the purpose of the Munich conference? Please help I dont understand An exergonic reaction __________ free energy, and an endergonic reaction __________ free energy. What are the three methods of calculating balance charges on credit cards?. Suppose the ski patrol lowers a rescue sled carrying an injured skier, with a combined mass of 97.5 kg, down a 60.0-degree slope at a constant speed, as shown in the Figure. The coefficient of kinetic friction between the sled and snow is 0.100. a) How much work, in joules, is done by friction as the sled moved 28 m along the hill?b) How much work, in joules, is done by the rope on the sled this distance?c) What is the work, in joules done by the gravitational force on the sled?d) What is the net work done on the sled, in joules? A uniform density curve goes from negative 5 to positive 1.What would the height need to be for this curve to be a density curve?Negative one-sixthOne-sixthOne-fifth1Picture posted below Describe the change in the graph of the parabola f(x) when it transforms into g(x) =The parabola g(x) will open in the opposite direction of f(x), and the parabola will be narrower than f(x).The parabola g(x) will open in the same direction of f(x), and the parabola will be narrower than f(x).The parabola g(x) will open in the opposite direction of f(x), and the parabola will be wider than f(x).The parabola g(x) will open in the same direction of f(x), and the parabola will be wider than f(x).